SysKonnect driver - SKFP¶
© Copyright 1998-2000 SysKonnect,
SysKonnect driver - SKFP created 11-May-2000
Readme File for skfp.o v2.06
This README explains how to use the driver ‘skfp’ for Linux with your network adapter.
Chapter 2: Contains a list of all network adapters that are supported by this driver.
- Chapter 3:
Gives some general information.
Chapter 4: Describes common problems and solutions.
Chapter 5: Shows the changed functionality of the adapter LEDs.
Chapter 6: History of development.
2. Supported adapters¶
The network driver ‘skfp’ supports the following network adapters: SysKonnect adapters:
SK-5521 (SK-NET FDDI-UP)
SK-5522 (SK-NET FDDI-UP DAS)
SK-5541 (SK-NET FDDI-FP)
SK-5543 (SK-NET FDDI-LP)
SK-5544 (SK-NET FDDI-LP DAS)
SK-5821 (SK-NET FDDI-UP64)
SK-5822 (SK-NET FDDI-UP64 DAS)
SK-5841 (SK-NET FDDI-FP64)
SK-5843 (SK-NET FDDI-LP64)
SK-5844 (SK-NET FDDI-LP64 DAS)
Compaq adapters (not tested):
Netelligent 100 FDDI DAS Fibre SC
Netelligent 100 FDDI SAS Fibre SC
Netelligent 100 FDDI DAS UTP
Netelligent 100 FDDI SAS UTP
Netelligent 100 FDDI SAS Fibre MIC
3. General Information¶
From v2.01 on, the driver is integrated in the linux kernel sources. Therefore, the installation is the same as for any other adapter supported by the kernel.
Refer to the manual of your distribution about the installation of network adapters.
Makes my life much easier :-)
If you run into problems during installation, check those items:
The FDDI adapter cannot be found by the driver.
Look in /proc/pci for the following entry:
‘FDDI network controller: SysKonnect SK-FDDI-PCI …’
If this entry exists, then the FDDI adapter has been found by the system and should be able to be used.
If this entry does not exist or if the file ‘/proc/pci’ is not there, then you may have a hardware problem or PCI support may not be enabled in your kernel.
The adapter can be checked using the diagnostic program which is available from the SysKonnect web site:
Some COMPAQ machines have a problem with PCI under Linux. This is described in the ‘PCI howto’ document (included in some distributions or available from the www, e.g. at ‘www.linux.org’) and no workaround is available.
You want to use your computer as a router between multiple IP subnetworks (using multiple adapters), but you cannot reach computers in other subnetworks.
Either the router’s kernel is not configured for IP forwarding or there is a problem with the routing table and gateway configuration in at least one of the computers.
If your problem is not listed here, please contact our technical support for help.
You can send email to: email@example.com
When contacting our technical support, please ensure that the following information is available:
System Manufacturer and Model
Boards in your system
5. Function of the Adapter LEDs¶
The functionality of the LED’s on the FDDI network adapters was changed in SMT version v2.82. With this new SMT version, the yellow LED works as a ring operational indicator. An active yellow LED indicates that the ring is down. The green LED on the adapter now works as a link indicator where an active GREEN LED indicates that the respective port has a physical connection.
With versions of SMT prior to v2.82 a ring up was indicated if the yellow LED was off while the green LED(s) showed the connection status of the adapter. During a ring down the green LED was off and the yellow LED was on.
All implementations indicate that a driver is not loaded if all LEDs are off.
- v2.06 (20000511) (In-Kernel version)
64 bit support
new pci dma interface
in kernel 2.3.99
- v2.05 (20000217) (In-Kernel version)
Changes for 2.3.45 kernel
- v2.04 (20000207) (Standalone version)
Added rx/tx byte counter
- v2.03 (20000111) (Standalone version)
Fixed printk statements from v2.02
- v2.02 (991215) (Standalone version)
Removed unnecessary output
Fixed path for “printver.sh” in makefile
- v2.01 (991122) (In-Kernel version)
Integration in Linux kernel sources
Support for memory mapped I/O.
- v2.00 (991112)
Full source released under GPL
- v1.05 (991023)
Compilation with kernel version 2.2.13 failed
- v1.04 (990427)
New SMT module included, changing LED functionality
Synchronization on SMP machines was buggy
- v1.03 (990325)
Interrupt routing on SMP machines could be incorrect
- v1.02 (990310)
Support for kernel versions 2.2.x added
Kernel patch instead of private duplicate of kernel functions
- v1.01 (980812)
Connection hangup with telnet Slow telnet connection
- v1.00 beta 01 (980507)
tar archive instead of standard package format (rpm).
FDDI statistic is empty.
not tested with 2.1.xx kernels
integration in kernel not tested
not tested simultaneously with FDDI adapters from other vendors.
only X86 processors supported.
SBA (Synchronous Bandwidth Allocator) parameters can not be configured.
does not work on some COMPAQ machines. See the PCI howto document for details about this problem.
data corruption with kernel versions below 2.0.33.