Generic Thermal Sysfs driver How To

Written by Sujith Thomas <sujith.thomas@intel.com>, Zhang Rui <rui.zhang@intel.com>

Copyright (c) 2008 Intel Corporation

0. Introduction

The generic thermal sysfs provides a set of interfaces for thermal zone devices (sensors) and thermal cooling devices (fan, processor...) to register with the thermal management solution and to be a part of it.

This how-to focuses on enabling new thermal zone and cooling devices to participate in thermal management. This solution is platform independent and any type of thermal zone devices and cooling devices should be able to make use of the infrastructure.

The main task of the thermal sysfs driver is to expose thermal zone attributes as well as cooling device attributes to the user space. An intelligent thermal management application can make decisions based on inputs from thermal zone attributes (the current temperature and trip point temperature) and throttle appropriate devices.

  • [0-*] denotes any positive number starting from 0

  • [1-*] denotes any positive number starting from 1

1. thermal sysfs driver interface functions

1.1 thermal zone device interface

struct thermal_zone_device *
thermal_zone_device_register_with_trips(const char *type,
                                const struct thermal_trip *trips,
                                int num_trips, void *devdata,
                                const struct thermal_zone_device_ops *ops,
                                const struct thermal_zone_params *tzp,
                                unsigned int passive_delay,
                                unsigned int polling_delay)

This interface function adds a new thermal zone device (sensor) to the /sys/class/thermal folder as thermal_zone[0-*]. It tries to bind all the thermal cooling devices registered to it at the same time.

type:

the thermal zone type.

trips:

the table of trip points for this thermal zone.

devdata:

device private data

ops:

thermal zone device call-backs.

.should_bind:

check whether or not a given cooling device should be bound to a given trip point in this thermal zone.

.get_temp:

get the current temperature of the thermal zone.

.set_trips:

set the trip points window. Whenever the current temperature is updated, the trip points immediately below and above the current temperature are found.

.change_mode:

change the mode (enabled/disabled) of the thermal zone.

.set_trip_temp:

set the temperature of a given trip point.

.get_crit_temp:

get the critical temperature for this thermal zone.

.set_emul_temp:

set the emulation temperature which helps in debugging different threshold temperature points.

.get_trend:

get the trend of most recent zone temperature changes.

.hot:

hot trip point crossing handler.

.critical:

critical trip point crossing handler.

tzp:

thermal zone platform parameters.

passive_delay:

number of milliseconds to wait between polls when performing passive cooling.

polling_delay:

number of milliseconds to wait between polls when checking whether trip points have been crossed (0 for interrupt driven systems).

void thermal_zone_device_unregister(struct thermal_zone_device *tz)

This interface function removes the thermal zone device. It deletes the corresponding entry from /sys/class/thermal folder and unbinds all the thermal cooling devices it uses.

struct thermal_zone_device
*thermal_zone_of_sensor_register(struct device *dev, int sensor_id,
                     void *data,
                     const struct thermal_zone_of_device_ops *ops)

This interface adds a new sensor to a DT thermal zone. This function will search the list of thermal zones described in device tree and look for the zone that refer to the sensor device pointed by dev->of_node as temperature providers. For the zone pointing to the sensor node, the sensor will be added to the DT thermal zone device.

The parameters for this interface are:

dev:

Device node of sensor containing valid node pointer in dev->of_node.

sensor_id:

a sensor identifier, in case the sensor IP has more than one sensors

data:

a private pointer (owned by the caller) that will be passed back, when a temperature reading is needed.

ops:

struct thermal_zone_of_device_ops *.

get_temp

a pointer to a function that reads the sensor temperature. This is mandatory callback provided by sensor driver.

set_trips

a pointer to a function that sets a temperature window. When this window is left the driver must inform the thermal core via thermal_zone_device_update.

get_trend

a pointer to a function that reads the sensor temperature trend.

set_emul_temp

a pointer to a function that sets sensor emulated temperature.

The thermal zone temperature is provided by the get_temp() function pointer of thermal_zone_of_device_ops. When called, it will have the private pointer @data back.

It returns error pointer if fails otherwise valid thermal zone device handle. Caller should check the return handle with IS_ERR() for finding whether success or not.

void thermal_zone_of_sensor_unregister(struct device *dev,
                                       struct thermal_zone_device *tzd)

This interface unregisters a sensor from a DT thermal zone which was successfully added by interface thermal_zone_of_sensor_register(). This function removes the sensor callbacks and private data from the thermal zone device registered with thermal_zone_of_sensor_register() interface. It will also silent the zone by remove the .get_temp() and get_trend() thermal zone device callbacks.

struct thermal_zone_device
*devm_thermal_zone_of_sensor_register(struct device *dev,
                      int sensor_id,
                      void *data,
                      const struct thermal_zone_of_device_ops *ops)

This interface is resource managed version of thermal_zone_of_sensor_register().

All details of thermal_zone_of_sensor_register() described in section 1.1.3 is applicable here.

The benefit of using this interface to register sensor is that it is not require to explicitly call thermal_zone_of_sensor_unregister() in error path or during driver unbinding as this is done by driver resource manager.

void devm_thermal_zone_of_sensor_unregister(struct device *dev,
                                struct thermal_zone_device *tzd)

This interface is resource managed version of thermal_zone_of_sensor_unregister(). All details of thermal_zone_of_sensor_unregister() described in section 1.1.4 is applicable here. Normally this function will not need to be called and the resource management code will ensure that the resource is freed.

int thermal_zone_get_slope(struct thermal_zone_device *tz)

This interface is used to read the slope attribute value for the thermal zone device, which might be useful for platform drivers for temperature calculations.

int thermal_zone_get_offset(struct thermal_zone_device *tz)

This interface is used to read the offset attribute value for the thermal zone device, which might be useful for platform drivers for temperature calculations.

1.2 thermal cooling device interface

struct thermal_cooling_device
*thermal_cooling_device_register(char *name,
                void *devdata, struct thermal_cooling_device_ops *)

This interface function adds a new thermal cooling device (fan/processor/...) to /sys/class/thermal/ folder as cooling_device[0-*]. It tries to bind itself to all the thermal zone devices registered at the same time.

name:

the cooling device name.

devdata:

device private data.

ops:

thermal cooling devices call-backs.

.get_max_state:

get the Maximum throttle state of the cooling device.

.get_cur_state:

get the Currently requested throttle state of the cooling device.

.set_cur_state:

set the Current throttle state of the cooling device.

void thermal_cooling_device_unregister(struct thermal_cooling_device *cdev)

This interface function removes the thermal cooling device. It deletes the corresponding entry from /sys/class/thermal folder and unbinds itself from all the thermal zone devices using it.

1.4 Thermal Zone Parameters

struct thermal_zone_params

This structure defines the platform level parameters for a thermal zone. This data, for each thermal zone should come from the platform layer. This is an optional feature where some platforms can choose not to provide this data.

.governor_name:

Name of the thermal governor used for this zone

.no_hwmon:

a boolean to indicate if the thermal to hwmon sysfs interface is required. when no_hwmon == false, a hwmon sysfs interface will be created. when no_hwmon == true, nothing will be done. In case the thermal_zone_params is NULL, the hwmon interface will be created (for backward compatibility).

2. sysfs attributes structure

RO

read only value

WO

write only value

RW

read/write value

Thermal sysfs attributes will be represented under /sys/class/thermal. Hwmon sysfs I/F extension is also available under /sys/class/hwmon if hwmon is compiled in or built as a module.

Thermal zone device sys I/F, created once it’s registered:

/sys/class/thermal/thermal_zone[0-*]:
  |---type:                   Type of the thermal zone
  |---temp:                   Current temperature
  |---mode:                   Working mode of the thermal zone
  |---policy:                 Thermal governor used for this zone
  |---available_policies:     Available thermal governors for this zone
  |---trip_point_[0-*]_temp:  Trip point temperature
  |---trip_point_[0-*]_type:  Trip point type
  |---trip_point_[0-*]_hyst:  Hysteresis value for this trip point
  |---emul_temp:              Emulated temperature set node
  |---sustainable_power:      Sustainable dissipatable power
  |---k_po:                   Proportional term during temperature overshoot
  |---k_pu:                   Proportional term during temperature undershoot
  |---k_i:                    PID's integral term in the power allocator gov
  |---k_d:                    PID's derivative term in the power allocator
  |---integral_cutoff:        Offset above which errors are accumulated
  |---slope:                  Slope constant applied as linear extrapolation
  |---offset:                 Offset constant applied as linear extrapolation

Thermal cooling device sys I/F, created once it’s registered:

/sys/class/thermal/cooling_device[0-*]:
  |---type:                   Type of the cooling device(processor/fan/...)
  |---max_state:              Maximum cooling state of the cooling device
  |---cur_state:              Current cooling state of the cooling device
  |---stats:                  Directory containing cooling device's statistics
  |---stats/reset:            Writing any value resets the statistics
  |---stats/time_in_state_ms: Time (msec) spent in various cooling states
  |---stats/total_trans:      Total number of times cooling state is changed
  |---stats/trans_table:      Cooling state transition table

Then next two dynamic attributes are created/removed in pairs. They represent the relationship between a thermal zone and its associated cooling device.

/sys/class/thermal/thermal_zone[0-*]:
  |---cdev[0-*]:              [0-*]th cooling device in current thermal zone
  |---cdev[0-*]_trip_point:   Trip point that cdev[0-*] is associated with
  |---cdev[0-*]_weight:       Influence of the cooling device in
                              this thermal zone

Besides the thermal zone device sysfs I/F and cooling device sysfs I/F, the generic thermal driver also creates a hwmon sysfs I/F for each _type_ of thermal zone device. E.g. the generic thermal driver registers one hwmon class device and build the associated hwmon sysfs I/F for all the registered ACPI thermal zones.

Please read Documentation/ABI/testing/sysfs-class-thermal for thermal zone and cooling device attribute details.

/sys/class/hwmon/hwmon[0-*]:
  |---name:                   The type of the thermal zone devices
  |---temp[1-*]_input:        The current temperature of thermal zone [1-*]
  |---temp[1-*]_critical:     The critical trip point of thermal zone [1-*]

Please read Naming and data format standards for sysfs files for additional information.

3. A simple implementation

ACPI thermal zone may support multiple trip points like critical, hot, passive, active. If an ACPI thermal zone supports critical, passive, active[0] and active[1] at the same time, it may register itself as a thermal_zone_device (thermal_zone1) with 4 trip points in all. It has one processor and one fan, which are both registered as thermal_cooling_device. Both are considered to have the same effectiveness in cooling the thermal zone.

If the processor is listed in _PSL method, and the fan is listed in _AL0 method, the sys I/F structure will be built like this:

/sys/class/thermal:
 |thermal_zone1:
   |---type:                   acpitz
   |---temp:                   37000
   |---mode:                   enabled
   |---policy:                 step_wise
   |---available_policies:     step_wise fair_share
   |---trip_point_0_temp:      100000
   |---trip_point_0_type:      critical
   |---trip_point_1_temp:      80000
   |---trip_point_1_type:      passive
   |---trip_point_2_temp:      70000
   |---trip_point_2_type:      active0
   |---trip_point_3_temp:      60000
   |---trip_point_3_type:      active1
   |---cdev0:                  --->/sys/class/thermal/cooling_device0
   |---cdev0_trip_point:       1       /* cdev0 can be used for passive */
   |---cdev0_weight:           1024
   |---cdev1:                  --->/sys/class/thermal/cooling_device3
   |---cdev1_trip_point:       2       /* cdev1 can be used for active[0]*/
   |---cdev1_weight:           1024

 |cooling_device0:
   |---type:                   Processor
   |---max_state:              8
   |---cur_state:              0

 |cooling_device3:
   |---type:                   Fan
   |---max_state:              2
   |---cur_state:              0

/sys/class/hwmon:
 |hwmon0:
   |---name:                   acpitz
   |---temp1_input:            37000
   |---temp1_crit:             100000

4. Export Symbol APIs

4.1. get_tz_trend

This function returns the trend of a thermal zone, i.e the rate of change of temperature of the thermal zone. Ideally, the thermal sensor drivers are supposed to implement the callback. If they don’t, the thermal framework calculated the trend by comparing the previous and the current temperature values.

4.2. thermal_cdev_update

This function serves as an arbitrator to set the state of a cooling device. It sets the cooling device to the deepest cooling state if possible.

5. thermal_emergency_poweroff

On an event of critical trip temperature crossing the thermal framework shuts down the system by calling hw_protection_shutdown(). The hw_protection_shutdown() first attempts to perform an orderly shutdown but accepts a delay after which it proceeds doing a forced power-off or as last resort an emergency_restart.

The delay should be carefully profiled so as to give adequate time for orderly poweroff.

If the delay is set to 0 emergency poweroff will not be supported. So a carefully profiled non-zero positive value is a must for emergency poweroff to be triggered.