1.7. V4L2 sub-devices¶
Many drivers need to communicate with sub-devices. These devices can do all sort of tasks, but most commonly they handle audio and/or video muxing, encoding or decoding. For webcams common sub-devices are sensors and camera controllers.
Usually these are I2C devices, but not necessarily. In order to provide the
driver with a consistent interface to these sub-devices the
v4l2_subdev
struct (v4l2-subdev.h) was created.
Each sub-device driver must have a v4l2_subdev
struct. This struct
can be stand-alone for simple sub-devices or it might be embedded in a larger
struct if more state information needs to be stored. Usually there is a
low-level device struct (e.g. i2c_client
) that contains the device data as
setup by the kernel. It is recommended to store that pointer in the private
data of v4l2_subdev
using v4l2_set_subdevdata()
. That makes
it easy to go from a v4l2_subdev
to the actual low-level bus-specific
device data.
You also need a way to go from the low-level struct to v4l2_subdev
.
For the common i2c_client struct the i2c_set_clientdata() call is used to store
a v4l2_subdev
pointer, for other buses you may have to use other
methods.
Bridges might also need to store per-subdev private data, such as a pointer to
bridge-specific per-subdev private data. The v4l2_subdev
structure
provides host private data for that purpose that can be accessed with
v4l2_get_subdev_hostdata()
and v4l2_set_subdev_hostdata()
.
From the bridge driver perspective, you load the sub-device module and somehow
obtain the v4l2_subdev
pointer. For i2c devices this is easy: you call
i2c_get_clientdata()
. For other buses something similar needs to be done.
Helper functions exists for sub-devices on an I2C bus that do most of this
tricky work for you.
Each v4l2_subdev
contains function pointers that sub-device drivers
can implement (or leave NULL
if it is not applicable). Since sub-devices can
do so many different things and you do not want to end up with a huge ops struct
of which only a handful of ops are commonly implemented, the function pointers
are sorted according to category and each category has its own ops struct.
The top-level ops struct contains pointers to the category ops structs, which may be NULL if the subdev driver does not support anything from that category.
It looks like this:
struct v4l2_subdev_core_ops {
int (*log_status)(struct v4l2_subdev *sd);
int (*init)(struct v4l2_subdev *sd, u32 val);
...
};
struct v4l2_subdev_tuner_ops {
...
};
struct v4l2_subdev_audio_ops {
...
};
struct v4l2_subdev_video_ops {
...
};
struct v4l2_subdev_pad_ops {
...
};
struct v4l2_subdev_ops {
const struct v4l2_subdev_core_ops *core;
const struct v4l2_subdev_tuner_ops *tuner;
const struct v4l2_subdev_audio_ops *audio;
const struct v4l2_subdev_video_ops *video;
const struct v4l2_subdev_pad_ops *video;
};
The core ops are common to all subdevs, the other categories are implemented depending on the sub-device. E.g. a video device is unlikely to support the audio ops and vice versa.
This setup limits the number of function pointers while still making it easy to add new ops and categories.
A sub-device driver initializes the v4l2_subdev
struct using:
Afterwards you need to initialize sd
->name with a
unique name and set the module owner. This is done for you if you use the
i2c helper functions.
If integration with the media framework is needed, you must initialize the
media_entity
struct embedded in the v4l2_subdev
struct
(entity field) by calling media_entity_pads_init()
, if the entity has
pads:
struct media_pad *pads = &my_sd->pads;
int err;
err = media_entity_pads_init(&sd->entity, npads, pads);
The pads array must have been previously initialized. There is no need to
manually set the struct media_entity
function and name fields, but the
revision field must be initialized if needed.
A reference to the entity will be automatically acquired/released when the subdev device node (if any) is opened/closed.
Don’t forget to cleanup the media entity before the sub-device is destroyed:
media_entity_cleanup(&sd->entity);
If the subdev driver intends to process video and integrate with the media
framework, it must implement format related functionality using
v4l2_subdev_pad_ops
instead of v4l2_subdev_video_ops
.
In that case, the subdev driver may set the link_validate field to provide its own link validation function. The link validation function is called for every link in the pipeline where both of the ends of the links are V4L2 sub-devices. The driver is still responsible for validating the correctness of the format configuration between sub-devices and video nodes.
If link_validate op is not set, the default function
v4l2_subdev_link_validate_default()
is used instead. This function
ensures that width, height and the media bus pixel code are equal on both source
and sink of the link. Subdev drivers are also free to use this function to
perform the checks mentioned above in addition to their own checks.
There are currently two ways to register subdevices with the V4L2 core. The first (traditional) possibility is to have subdevices registered by bridge drivers. This can be done when the bridge driver has the complete information about subdevices connected to it and knows exactly when to register them. This is typically the case for internal subdevices, like video data processing units within SoCs or complex PCI(e) boards, camera sensors in USB cameras or connected to SoCs, which pass information about them to bridge drivers, usually in their platform data.
There are however also situations where subdevices have to be registered asynchronously to bridge devices. An example of such a configuration is a Device Tree based system where information about subdevices is made available to the system independently from the bridge devices, e.g. when subdevices are defined in DT as I2C device nodes. The API used in this second case is described further below.
Using one or the other registration method only affects the probing process, the run-time bridge-subdevice interaction is in both cases the same.
In the synchronous case a device (bridge) driver needs to register the
v4l2_subdev
with the v4l2_device:
This can fail if the subdev module disappeared before it could be registered.
After this function was called successfully the subdev->dev field points to
the v4l2_device
.
If the v4l2_device parent device has a non-NULL mdev field, the sub-device entity will be automatically registered with the media device.
You can unregister a sub-device using:
Afterwards the subdev module can be unloaded and
sd
->dev == NULL
.
You can call an ops function either directly:
err = sd->ops->core->g_std(sd, &norm);
but it is better and easier to use this macro:
err = v4l2_subdev_call(sd, core, g_std, &norm);
The macro will to the right NULL
pointer checks and returns -ENODEV
if sd
is NULL
, -ENOIOCTLCMD
if either
sd
->core or sd
->core->g_std is NULL
, or the actual result of the
sd
->ops->core->g_std ops.
It is also possible to call all or a subset of the sub-devices:
v4l2_device_call_all(v4l2_dev, 0, core, g_std, &norm);
Any subdev that does not support this ops is skipped and error results are ignored. If you want to check for errors use this:
err = v4l2_device_call_until_err(v4l2_dev, 0, core, g_std, &norm);
Any error except -ENOIOCTLCMD
will exit the loop with that error. If no
errors (except -ENOIOCTLCMD
) occurred, then 0 is returned.
The second argument to both calls is a group ID. If 0, then all subdevs are
called. If non-zero, then only those whose group ID match that value will
be called. Before a bridge driver registers a subdev it can set
sd
->grp_id to whatever value it wants (it’s 0 by
default). This value is owned by the bridge driver and the sub-device driver
will never modify or use it.
The group ID gives the bridge driver more control how callbacks are called.
For example, there may be multiple audio chips on a board, each capable of
changing the volume. But usually only one will actually be used when the
user want to change the volume. You can set the group ID for that subdev to
e.g. AUDIO_CONTROLLER and specify that as the group ID value when calling
v4l2_device_call_all()
. That ensures that it will only go to the subdev
that needs it.
If the sub-device needs to notify its v4l2_device parent of an event, then
it can call v4l2_subdev_notify(sd, notification, arg)
. This macro checks
whether there is a notify()
callback defined and returns -ENODEV
if not.
Otherwise the result of the notify()
call is returned.
The advantage of using v4l2_subdev
is that it is a generic struct and
does not contain any knowledge about the underlying hardware. So a driver might
contain several subdevs that use an I2C bus, but also a subdev that is
controlled through GPIO pins. This distinction is only relevant when setting
up the device, but once the subdev is registered it is completely transparent.
In the asynchronous case subdevice probing can be invoked independently of the
bridge driver availability. The subdevice driver then has to verify whether all
the requirements for a successful probing are satisfied. This can include a
check for a master clock availability. If any of the conditions aren’t satisfied
the driver might decide to return -EPROBE_DEFER
to request further reprobing
attempts. Once all conditions are met the subdevice shall be registered using
the v4l2_async_register_subdev()
function. Unregistration is
performed using the v4l2_async_unregister_subdev()
call. Subdevices
registered this way are stored in a global list of subdevices, ready to be
picked up by bridge drivers.
Bridge drivers in turn have to register a notifier object. This is
performed using the v4l2_async_notifier_register()
call. To
unregister the notifier the driver has to call
v4l2_async_notifier_unregister()
. The former of the two functions
takes two arguments: a pointer to struct v4l2_device
and a
pointer to struct v4l2_async_notifier
.
Before registering the notifier, bridge drivers must do two things:
first, the notifier must be initialized using the
v4l2_async_notifier_init()
. Second, bridge drivers can then
begin to form a list of subdevice descriptors that the bridge device
needs for its operation. Subdevice descriptors are added to the notifier
using the v4l2_async_notifier_add_subdev()
call. This function
takes two arguments: a pointer to struct v4l2_async_notifier
,
and a pointer to the subdevice descripter, which is of type struct
v4l2_async_subdev
.
The V4L2 core will then use these descriptors to match asynchronously
registered subdevices to them. If a match is detected the .bound()
notifier callback is called. After all subdevices have been located the
.complete() callback is called. When a subdevice is removed from the
system the .unbind() method is called. All three callbacks are optional.
1.8. V4L2 sub-device userspace API¶
Beside exposing a kernel API through the v4l2_subdev_ops
structure,
V4L2 sub-devices can also be controlled directly by userspace applications.
Device nodes named v4l-subdev
X can be created in /dev
to access
sub-devices directly. If a sub-device supports direct userspace configuration
it must set the V4L2_SUBDEV_FL_HAS_DEVNODE
flag before being registered.
After registering sub-devices, the v4l2_device
driver can create
device nodes for all registered sub-devices marked with
V4L2_SUBDEV_FL_HAS_DEVNODE
by calling
v4l2_device_register_subdev_nodes()
. Those device nodes will be
automatically removed when sub-devices are unregistered.
The device node handles a subset of the V4L2 API.
VIDIOC_QUERYCTRL
,
VIDIOC_QUERYMENU
,
VIDIOC_G_CTRL
,
VIDIOC_S_CTRL
,
VIDIOC_G_EXT_CTRLS
,
VIDIOC_S_EXT_CTRLS
and
VIDIOC_TRY_EXT_CTRLS
:
The controls ioctls are identical to the ones defined in V4L2. They behave identically, with the only exception that they deal only with controls implemented in the sub-device. Depending on the driver, those controls can be also be accessed through one (or several) V4L2 device nodes.
VIDIOC_DQEVENT
,
VIDIOC_SUBSCRIBE_EVENT
and
VIDIOC_UNSUBSCRIBE_EVENT
The events ioctls are identical to the ones defined in V4L2. They behave identically, with the only exception that they deal only with events generated by the sub-device. Depending on the driver, those events can also be reported by one (or several) V4L2 device nodes.
Sub-device drivers that want to use events need to set the
V4L2_SUBDEV_USES_EVENTS
v4l2_subdev
.flags and initializev4l2_subdev
.nevents to events queue depth before registering the sub-device. After registration events can be queued as usual on thev4l2_subdev
.devnode device node.To properly support events, the
poll()
file operation is also implemented.
Private ioctls
All ioctls not in the above list are passed directly to the sub-device driver through the core::ioctl operation.
1.9. I2C sub-device drivers¶
Since these drivers are so common, special helper functions are available to
ease the use of these drivers (v4l2-common.h
).
The recommended method of adding v4l2_subdev
support to an I2C driver
is to embed the v4l2_subdev
struct into the state struct that is
created for each I2C device instance. Very simple devices have no state
struct and in that case you can just create a v4l2_subdev
directly.
A typical state struct would look like this (where ‘chipname’ is replaced by the name of the chip):
struct chipname_state {
struct v4l2_subdev sd;
... /* additional state fields */
};
Initialize the v4l2_subdev
struct as follows:
v4l2_i2c_subdev_init(&state->sd, client, subdev_ops);
This function will fill in all the fields of v4l2_subdev
ensure that
the v4l2_subdev
and i2c_client both point to one another.
You should also add a helper inline function to go from a v4l2_subdev
pointer to a chipname_state struct:
static inline struct chipname_state *to_state(struct v4l2_subdev *sd)
{
return container_of(sd, struct chipname_state, sd);
}
Use this to go from the v4l2_subdev
struct to the i2c_client
struct:
struct i2c_client *client = v4l2_get_subdevdata(sd);
And this to go from an i2c_client
to a v4l2_subdev
struct:
struct v4l2_subdev *sd = i2c_get_clientdata(client);
Make sure to call
v4l2_device_unregister_subdev()
(sd
)
when the remove()
callback is called. This will unregister the sub-device
from the bridge driver. It is safe to call this even if the sub-device was
never registered.
You need to do this because when the bridge driver destroys the i2c adapter
the remove()
callbacks are called of the i2c devices on that adapter.
After that the corresponding v4l2_subdev structures are invalid, so they
have to be unregistered first. Calling
v4l2_device_unregister_subdev()
(sd
)
from the remove()
callback ensures that this is always done correctly.
The bridge driver also has some helper functions it can use:
struct v4l2_subdev *sd = v4l2_i2c_new_subdev(v4l2_dev, adapter,
"module_foo", "chipid", 0x36, NULL);
This loads the given module (can be NULL
if no module needs to be loaded)
and calls i2c_new_device()
with the given i2c_adapter
and
chip/address arguments. If all goes well, then it registers the subdev with
the v4l2_device.
You can also use the last argument of v4l2_i2c_new_subdev()
to pass
an array of possible I2C addresses that it should probe. These probe addresses
are only used if the previous argument is 0. A non-zero argument means that you
know the exact i2c address so in that case no probing will take place.
Both functions return NULL
if something went wrong.
Note that the chipid you pass to v4l2_i2c_new_subdev()
is usually
the same as the module name. It allows you to specify a chip variant, e.g.
“saa7114” or “saa7115”. In general though the i2c driver autodetects this.
The use of chipid is something that needs to be looked at more closely at a
later date. It differs between i2c drivers and as such can be confusing.
To see which chip variants are supported you can look in the i2c driver code
for the i2c_device_id table. This lists all the possibilities.
There are one more helper function:
v4l2_i2c_new_subdev_board()
uses an i2c_board_info
struct
which is passed to the i2c driver and replaces the irq, platform_data and addr
arguments.
If the subdev supports the s_config core ops, then that op is called with the irq and platform_data arguments after the subdev was setup.
The v4l2_i2c_new_subdev()
function will call
v4l2_i2c_new_subdev_board()
, internally filling a
i2c_board_info
structure using the client_type
and the
addr
to fill it.
1.10. V4L2 sub-device functions and data structures¶
-
struct
v4l2_decode_vbi_line
¶ used to decode_vbi_line
Definition
struct v4l2_decode_vbi_line {
u32 is_second_field;
u8 *p;
u32 line;
u32 type;
};
Members
is_second_field
- Set to 0 for the first (odd) field; set to 1 for the second (even) field.
p
- Pointer to the sliced VBI data from the decoder. On exit, points to the start of the payload.
line
- Line number of the sliced VBI data (1-23)
type
- VBI service type (V4L2_SLICED_*). 0 if no service found
-
enum
v4l2_subdev_io_pin_bits
¶ Subdevice external IO pin configuration bits
Constants
V4L2_SUBDEV_IO_PIN_DISABLE
- disables a pin config. ENABLE assumed.
V4L2_SUBDEV_IO_PIN_OUTPUT
- set it if pin is an output.
V4L2_SUBDEV_IO_PIN_INPUT
- set it if pin is an input.
V4L2_SUBDEV_IO_PIN_SET_VALUE
- to set the output value via
struct v4l2_subdev_io_pin_config
->value. V4L2_SUBDEV_IO_PIN_ACTIVE_LOW
- pin active is bit 0. Otherwise, ACTIVE HIGH is assumed.
-
struct
v4l2_subdev_io_pin_config
¶ Subdevice external IO pin configuration
Definition
struct v4l2_subdev_io_pin_config {
u32 flags;
u8 pin;
u8 function;
u8 value;
u8 strength;
};
Members
flags
- bitmask with flags for this pin’s config, whose bits are defined by
enum v4l2_subdev_io_pin_bits
. pin
- Chip external IO pin to configure
function
- Internal signal pad/function to route to IO pin
value
- Initial value for pin - e.g. GPIO output value
strength
- Pin drive strength
-
struct
v4l2_subdev_core_ops
¶ Define core ops callbacks for subdevs
Definition
struct v4l2_subdev_core_ops {
int (*log_status)(struct v4l2_subdev *sd);
int (*s_io_pin_config)(struct v4l2_subdev *sd, size_t n, struct v4l2_subdev_io_pin_config *pincfg);
int (*init)(struct v4l2_subdev *sd, u32 val);
int (*load_fw)(struct v4l2_subdev *sd);
int (*reset)(struct v4l2_subdev *sd, u32 val);
int (*s_gpio)(struct v4l2_subdev *sd, u32 val);
long (*ioctl)(struct v4l2_subdev *sd, unsigned int cmd, void *arg);
#ifdef CONFIG_COMPAT;
long (*compat_ioctl32)(struct v4l2_subdev *sd, unsigned int cmd, unsigned long arg);
#endif;
#ifdef CONFIG_VIDEO_ADV_DEBUG;
int (*g_register)(struct v4l2_subdev *sd, struct v4l2_dbg_register *reg);
int (*s_register)(struct v4l2_subdev *sd, const struct v4l2_dbg_register *reg);
#endif;
int (*s_power)(struct v4l2_subdev *sd, int on);
int (*interrupt_service_routine)(struct v4l2_subdev *sd, u32 status, bool *handled);
int (*subscribe_event)(struct v4l2_subdev *sd, struct v4l2_fh *fh, struct v4l2_event_subscription *sub);
int (*unsubscribe_event)(struct v4l2_subdev *sd, struct v4l2_fh *fh, struct v4l2_event_subscription *sub);
};
Members
log_status
- callback for
VIDIOC_LOG_STATUS()
ioctl handler code. s_io_pin_config
- configure one or more chip I/O pins for chips that multiplex different internal signal pads out to IO pins. This function takes a pointer to an array of ‘n’ pin configuration entries, one for each pin being configured. This function could be called at times other than just subdevice initialization.
init
- initialize the sensor registers to some sort of reasonable default values. Do not use for new drivers and should be removed in existing drivers.
load_fw
- load firmware.
reset
- generic reset command. The argument selects which subsystems to reset. Passing 0 will always reset the whole chip. Do not use for new drivers without discussing this first on the linux-media mailinglist. There should be no reason normally to reset a device.
s_gpio
- set GPIO pins. Very simple right now, might need to be extended with a direction argument if needed.
ioctl
- called at the end of ioctl() syscall handler at the V4L2 core. used to provide support for private ioctls used on the driver.
compat_ioctl32
- called when a 32 bits application uses a 64 bits Kernel, in order to fix data passed from/to userspace.
g_register
- callback for
VIDIOC_DBG_G_REGISTER()
ioctl handler code. s_register
- callback for
VIDIOC_DBG_S_REGISTER()
ioctl handler code. s_power
- puts subdevice in power saving mode (on == 0) or normal operation mode (on == 1).
interrupt_service_routine
- Called by the bridge chip’s interrupt service handler, when an interrupt status has be raised due to this subdev, so that this subdev can handle the details. It may schedule work to be performed later. It must not sleep. Called from an IRQ context.
subscribe_event
- used by the drivers to request the control framework that for it to be warned when the value of a control changes.
unsubscribe_event
- remove event subscription from the control framework.
-
struct
v4l2_subdev_tuner_ops
¶ Callbacks used when v4l device was opened in radio mode.
Definition
struct v4l2_subdev_tuner_ops {
int (*standby)(struct v4l2_subdev *sd);
int (*s_radio)(struct v4l2_subdev *sd);
int (*s_frequency)(struct v4l2_subdev *sd, const struct v4l2_frequency *freq);
int (*g_frequency)(struct v4l2_subdev *sd, struct v4l2_frequency *freq);
int (*enum_freq_bands)(struct v4l2_subdev *sd, struct v4l2_frequency_band *band);
int (*g_tuner)(struct v4l2_subdev *sd, struct v4l2_tuner *vt);
int (*s_tuner)(struct v4l2_subdev *sd, const struct v4l2_tuner *vt);
int (*g_modulator)(struct v4l2_subdev *sd, struct v4l2_modulator *vm);
int (*s_modulator)(struct v4l2_subdev *sd, const struct v4l2_modulator *vm);
int (*s_type_addr)(struct v4l2_subdev *sd, struct tuner_setup *type);
int (*s_config)(struct v4l2_subdev *sd, const struct v4l2_priv_tun_config *config);
};
Members
standby
- puts the tuner in standby mode. It will be woken up automatically the next time it is used.
s_radio
- callback that switches the tuner to radio mode. drivers should explicitly call it when a tuner ops should operate on radio mode, before being able to handle it. Used on devices that have both AM/FM radio receiver and TV.
s_frequency
- callback for
VIDIOC_S_FREQUENCY()
ioctl handler code. g_frequency
- callback for
VIDIOC_G_FREQUENCY()
ioctl handler code. freq->type must be filled in. Normally done byvideo_ioctl2()
or the bridge driver. enum_freq_bands
- callback for
VIDIOC_ENUM_FREQ_BANDS()
ioctl handler code. g_tuner
- callback for
VIDIOC_G_TUNER()
ioctl handler code. s_tuner
- callback for
VIDIOC_S_TUNER()
ioctl handler code. vt->type must be filled in. Normally done by video_ioctl2 or the bridge driver. g_modulator
- callback for
VIDIOC_G_MODULATOR()
ioctl handler code. s_modulator
- callback for
VIDIOC_S_MODULATOR()
ioctl handler code. s_type_addr
- sets tuner type and its I2C addr.
s_config
- sets tda9887 specific stuff, like port1, port2 and qss
Description
Note
On devices that have both AM/FM and TV, it is up to the driver
to explicitly call s_radio when the tuner should be switched to
radio mode, before handling other struct v4l2_subdev_tuner_ops
that would require it. An example of such usage is:
static void s_frequency(void *priv, const struct v4l2_frequency *f)
{
...
if (f.type == V4L2_TUNER_RADIO)
v4l2_device_call_all(v4l2_dev, 0, tuner, s_radio);
...
v4l2_device_call_all(v4l2_dev, 0, tuner, s_frequency);
}
-
struct
v4l2_subdev_audio_ops
¶ Callbacks used for audio-related settings
Definition
struct v4l2_subdev_audio_ops {
int (*s_clock_freq)(struct v4l2_subdev *sd, u32 freq);
int (*s_i2s_clock_freq)(struct v4l2_subdev *sd, u32 freq);
int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config);
int (*s_stream)(struct v4l2_subdev *sd, int enable);
};
Members
s_clock_freq
- set the frequency (in Hz) of the audio clock output. Used to slave an audio processor to the video decoder, ensuring that audio and video remain synchronized. Usual values for the frequency are 48000, 44100 or 32000 Hz. If the frequency is not supported, then -EINVAL is returned.
s_i2s_clock_freq
- sets I2S speed in bps. This is used to provide a standard
way to select I2S clock used by driving digital audio streams at some
board designs. Usual values for the frequency are 1024000 and 2048000.
If the frequency is not supported, then
-EINVAL
is returned. s_routing
- used to define the input and/or output pins of an audio chip, and any additional configuration data. Never attempt to use user-level input IDs (e.g. Composite, S-Video, Tuner) at this level. An i2c device shouldn’t know about whether an input pin is connected to a Composite connector, become on another board or platform it might be connected to something else entirely. The calling driver is responsible for mapping a user-level input to the right pins on the i2c device.
s_stream
- used to notify the audio code that stream will start or has stopped.
-
enum
v4l2_mbus_frame_desc_flags
¶ media bus frame description flags
Constants
V4L2_MBUS_FRAME_DESC_FL_LEN_MAX
- Indicates that
struct v4l2_mbus_frame_desc_entry
->length field specifies maximum data length. V4L2_MBUS_FRAME_DESC_FL_BLOB
- Indicates that the format does not have line offsets, i.e. the receiver should use 1D DMA.
-
struct
v4l2_mbus_frame_desc_entry
¶ media bus frame description structure
Definition
struct v4l2_mbus_frame_desc_entry {
enum v4l2_mbus_frame_desc_flags flags;
u32 pixelcode;
u32 length;
};
Members
flags
- bitmask flags, as defined by
enum v4l2_mbus_frame_desc_flags
. pixelcode
- media bus pixel code, valid if flags
FRAME_DESC_FL_BLOB
is not set. length
- number of octets per frame, valid if flags
V4L2_MBUS_FRAME_DESC_FL_LEN_MAX
is set.
-
struct
v4l2_mbus_frame_desc
¶ media bus data frame description
Definition
struct v4l2_mbus_frame_desc {
struct v4l2_mbus_frame_desc_entry entry[V4L2_FRAME_DESC_ENTRY_MAX];
unsigned short num_entries;
};
Members
entry
- frame descriptors array
num_entries
- number of entries in entry array
-
struct
v4l2_subdev_video_ops
¶ Callbacks used when v4l device was opened in video mode.
Definition
struct v4l2_subdev_video_ops {
int (*s_routing)(struct v4l2_subdev *sd, u32 input, u32 output, u32 config);
int (*s_crystal_freq)(struct v4l2_subdev *sd, u32 freq, u32 flags);
int (*g_std)(struct v4l2_subdev *sd, v4l2_std_id *norm);
int (*s_std)(struct v4l2_subdev *sd, v4l2_std_id norm);
int (*s_std_output)(struct v4l2_subdev *sd, v4l2_std_id std);
int (*g_std_output)(struct v4l2_subdev *sd, v4l2_std_id *std);
int (*querystd)(struct v4l2_subdev *sd, v4l2_std_id *std);
int (*g_tvnorms)(struct v4l2_subdev *sd, v4l2_std_id *std);
int (*g_tvnorms_output)(struct v4l2_subdev *sd, v4l2_std_id *std);
int (*g_input_status)(struct v4l2_subdev *sd, u32 *status);
int (*s_stream)(struct v4l2_subdev *sd, int enable);
int (*g_pixelaspect)(struct v4l2_subdev *sd, struct v4l2_fract *aspect);
int (*g_frame_interval)(struct v4l2_subdev *sd, struct v4l2_subdev_frame_interval *interval);
int (*s_frame_interval)(struct v4l2_subdev *sd, struct v4l2_subdev_frame_interval *interval);
int (*s_dv_timings)(struct v4l2_subdev *sd, struct v4l2_dv_timings *timings);
int (*g_dv_timings)(struct v4l2_subdev *sd, struct v4l2_dv_timings *timings);
int (*query_dv_timings)(struct v4l2_subdev *sd, struct v4l2_dv_timings *timings);
int (*g_mbus_config)(struct v4l2_subdev *sd, struct v4l2_mbus_config *cfg);
int (*s_mbus_config)(struct v4l2_subdev *sd, const struct v4l2_mbus_config *cfg);
int (*s_rx_buffer)(struct v4l2_subdev *sd, void *buf, unsigned int *size);
};
Members
s_routing
- see s_routing in audio_ops, except this version is for video devices.
s_crystal_freq
- sets the frequency of the crystal used to generate the clocks in Hz. An extra flags field allows device specific configuration regarding clock frequency dividers, etc. If not used, then set flags to 0. If the frequency is not supported, then -EINVAL is returned.
g_std
- callback for
VIDIOC_G_STD()
ioctl handler code. s_std
- callback for
VIDIOC_S_STD()
ioctl handler code. s_std_output
- set v4l2_std_id for video OUTPUT devices. This is ignored by video input devices.
g_std_output
- get current standard for video OUTPUT devices. This is ignored by video input devices.
querystd
- callback for
VIDIOC_QUERYSTD()
ioctl handler code. g_tvnorms
- get
v4l2_std_id
with all standards supported by the video CAPTURE device. This is ignored by video output devices. g_tvnorms_output
- get v4l2_std_id with all standards supported by the video OUTPUT device. This is ignored by video capture devices.
g_input_status
- get input status. Same as the status field in the
struct
v4l2_input
s_stream
- used to notify the driver that a video stream will start or has stopped.
g_pixelaspect
- callback to return the pixelaspect ratio.
g_frame_interval
- callback for
VIDIOC_SUBDEV_G_FRAME_INTERVAL()
ioctl handler code. s_frame_interval
- callback for
VIDIOC_SUBDEV_S_FRAME_INTERVAL()
ioctl handler code. s_dv_timings
- Set custom dv timings in the sub device. This is used when sub device is capable of setting detailed timing information in the hardware to generate/detect the video signal.
g_dv_timings
- Get custom dv timings in the sub device.
query_dv_timings
- callback for
VIDIOC_QUERY_DV_TIMINGS()
ioctl handler code. g_mbus_config
- get supported mediabus configurations
s_mbus_config
- set a certain mediabus configuration. This operation is added for compatibility with soc-camera drivers and should not be used by new software.
s_rx_buffer
- set a host allocated memory buffer for the subdev. The subdev can adjust size to a lower value and must not write more data to the buffer starting at data than the original value of size.
-
struct
v4l2_subdev_vbi_ops
¶ Callbacks used when v4l device was opened in video mode via the vbi device node.
Definition
struct v4l2_subdev_vbi_ops {
int (*decode_vbi_line)(struct v4l2_subdev *sd, struct v4l2_decode_vbi_line *vbi_line);
int (*s_vbi_data)(struct v4l2_subdev *sd, const struct v4l2_sliced_vbi_data *vbi_data);
int (*g_vbi_data)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_data *vbi_data);
int (*g_sliced_vbi_cap)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_cap *cap);
int (*s_raw_fmt)(struct v4l2_subdev *sd, struct v4l2_vbi_format *fmt);
int (*g_sliced_fmt)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_format *fmt);
int (*s_sliced_fmt)(struct v4l2_subdev *sd, struct v4l2_sliced_vbi_format *fmt);
};
Members
decode_vbi_line
- video decoders that support sliced VBI need to implement
this ioctl. Field p of the
struct v4l2_decode_vbi_line
is set to the start of the VBI data that was generated by the decoder. The driver then parses the sliced VBI data and sets the other fields in the struct accordingly. The pointer p is updated to point to the start of the payload which can be copied verbatim into the data field of thestruct v4l2_sliced_vbi_data
. If no valid VBI data was found, then the type field is set to 0 on return. s_vbi_data
- used to generate VBI signals on a video signal.
struct v4l2_sliced_vbi_data
is filled with the data packets that should be output. Note that if you set the line field to 0, then that VBI signal is disabled. If no valid VBI data was found, then the type field is set to 0 on return. g_vbi_data
- used to obtain the sliced VBI packet from a readback register.
Not all video decoders support this. If no data is available because
the readback register contains invalid or erroneous data
-EIO
is returned. Note that you must fill in the ‘id’ member and the ‘field’ member (to determine whether CC data from the first or second field should be obtained). g_sliced_vbi_cap
- callback for
VIDIOC_G_SLICED_VBI_CAP()
ioctl handler code. s_raw_fmt
- setup the video encoder/decoder for raw VBI.
g_sliced_fmt
- retrieve the current sliced VBI settings.
s_sliced_fmt
- setup the sliced VBI settings.
-
struct
v4l2_subdev_sensor_ops
¶ v4l2-subdev sensor operations
Definition
struct v4l2_subdev_sensor_ops {
int (*g_skip_top_lines)(struct v4l2_subdev *sd, u32 *lines);
int (*g_skip_frames)(struct v4l2_subdev *sd, u32 *frames);
};
Members
g_skip_top_lines
- number of lines at the top of the image to be skipped. This is needed for some sensors, which always corrupt several top lines of the output image, or which send their metadata in them.
g_skip_frames
- number of frames to skip at stream start. This is needed for buggy sensors that generate faulty frames when they are turned on.
-
enum
v4l2_subdev_ir_mode
¶ describes the type of IR supported
Constants
V4L2_SUBDEV_IR_MODE_PULSE_WIDTH
- IR uses struct ir_raw_event records
-
struct
v4l2_subdev_ir_parameters
¶ Parameters for IR TX or TX
Definition
struct v4l2_subdev_ir_parameters {
unsigned int bytes_per_data_element;
enum v4l2_subdev_ir_mode mode;
bool enable;
bool interrupt_enable;
bool shutdown;
bool modulation;
u32 max_pulse_width;
unsigned int carrier_freq;
unsigned int duty_cycle;
bool invert_level;
bool invert_carrier_sense;
u32 noise_filter_min_width;
unsigned int carrier_range_lower;
unsigned int carrier_range_upper;
u32 resolution;
};
Members
bytes_per_data_element
- bytes per data element of data in read or write call.
mode
- IR mode as defined by
enum v4l2_subdev_ir_mode
. enable
- device is active if true
interrupt_enable
- IR interrupts are enabled if true
shutdown
- if true: set hardware to low/no power, false: normal mode
modulation
- if true, it uses carrier, if false: baseband
max_pulse_width
- maximum pulse width in ns, valid only for baseband signal
carrier_freq
- carrier frequency in Hz, valid only for modulated signal
duty_cycle
- duty cycle percentage, valid only for modulated signal
invert_level
- invert signal level
invert_carrier_sense
- Send 0/space as a carrier burst. used only in TX.
noise_filter_min_width
- min time of a valid pulse, in ns. Used only for RX.
carrier_range_lower
- Lower carrier range, in Hz, valid only for modulated signal. Used only for RX.
carrier_range_upper
- Upper carrier range, in Hz, valid only for modulated signal. Used only for RX.
resolution
- The receive resolution, in ns . Used only for RX.
-
struct
v4l2_subdev_ir_ops
¶ operations for IR subdevices
Definition
struct v4l2_subdev_ir_ops {
int (*rx_read)(struct v4l2_subdev *sd, u8 *buf, size_t count, ssize_t *num);
int (*rx_g_parameters)(struct v4l2_subdev *sd, struct v4l2_subdev_ir_parameters *params);
int (*rx_s_parameters)(struct v4l2_subdev *sd, struct v4l2_subdev_ir_parameters *params);
int (*tx_write)(struct v4l2_subdev *sd, u8 *buf, size_t count, ssize_t *num);
int (*tx_g_parameters)(struct v4l2_subdev *sd, struct v4l2_subdev_ir_parameters *params);
int (*tx_s_parameters)(struct v4l2_subdev *sd, struct v4l2_subdev_ir_parameters *params);
};
Members
rx_read
- Reads received codes or pulse width data. The semantics are similar to a non-blocking read() call.
rx_g_parameters
- Get the current operating parameters and state of the the IR receiver.
rx_s_parameters
- Set the current operating parameters and state of the the IR receiver. It is recommended to call [rt]x_g_parameters first to fill out the current state, and only change the fields that need to be changed. Upon return, the actual device operating parameters and state will be returned. Note that hardware limitations may prevent the actual settings from matching the requested settings - e.g. an actual carrier setting of 35,904 Hz when 36,000 Hz was requested. An exception is when the shutdown parameter is true. The last used operational parameters will be returned, but the actual state of the hardware be different to minimize power consumption and processing when shutdown is true.
tx_write
- Writes codes or pulse width data for transmission. The semantics are similar to a non-blocking write() call.
tx_g_parameters
- Get the current operating parameters and state of the the IR transmitter.
tx_s_parameters
- Set the current operating parameters and state of the the IR transmitter. It is recommended to call [rt]x_g_parameters first to fill out the current state, and only change the fields that need to be changed. Upon return, the actual device operating parameters and state will be returned. Note that hardware limitations may prevent the actual settings from matching the requested settings - e.g. an actual carrier setting of 35,904 Hz when 36,000 Hz was requested. An exception is when the shutdown parameter is true. The last used operational parameters will be returned, but the actual state of the hardware be different to minimize power consumption and processing when shutdown is true.
-
struct
v4l2_subdev_pad_config
¶ Used for storing subdev pad information.
Definition
struct v4l2_subdev_pad_config {
struct v4l2_mbus_framefmt try_fmt;
struct v4l2_rect try_crop;
struct v4l2_rect try_compose;
};
Members
try_fmt
struct v4l2_mbus_framefmt
try_crop
struct v4l2_rect
to be used for croptry_compose
struct v4l2_rect
to be used for compose
Description
This structure only needs to be passed to the pad op if the ‘which’ field
of the main argument is set to V4L2_SUBDEV_FORMAT_TRY
. For
V4L2_SUBDEV_FORMAT_ACTIVE
it is safe to pass NULL
.
-
struct
v4l2_subdev_pad_ops
¶ v4l2-subdev pad level operations
Definition
struct v4l2_subdev_pad_ops {
int (*init_cfg)(struct v4l2_subdev *sd, struct v4l2_subdev_pad_config *cfg);
int (*enum_mbus_code)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_mbus_code_enum *code);
int (*enum_frame_size)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_frame_size_enum *fse);
int (*enum_frame_interval)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_frame_interval_enum *fie);
int (*get_fmt)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_format *format);
int (*set_fmt)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_format *format);
int (*get_selection)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_selection *sel);
int (*set_selection)(struct v4l2_subdev *sd,struct v4l2_subdev_pad_config *cfg, struct v4l2_subdev_selection *sel);
int (*get_edid)(struct v4l2_subdev *sd, struct v4l2_edid *edid);
int (*set_edid)(struct v4l2_subdev *sd, struct v4l2_edid *edid);
int (*dv_timings_cap)(struct v4l2_subdev *sd, struct v4l2_dv_timings_cap *cap);
int (*enum_dv_timings)(struct v4l2_subdev *sd, struct v4l2_enum_dv_timings *timings);
#ifdef CONFIG_MEDIA_CONTROLLER;
int (*link_validate)(struct v4l2_subdev *sd, struct media_link *link,struct v4l2_subdev_format *source_fmt, struct v4l2_subdev_format *sink_fmt);
#endif ;
int (*get_frame_desc)(struct v4l2_subdev *sd, unsigned int pad, struct v4l2_mbus_frame_desc *fd);
int (*set_frame_desc)(struct v4l2_subdev *sd, unsigned int pad, struct v4l2_mbus_frame_desc *fd);
};
Members
init_cfg
- initialize the pad config to default values
enum_mbus_code
- callback for
VIDIOC_SUBDEV_ENUM_MBUS_CODE()
ioctl handler code. enum_frame_size
- callback for
VIDIOC_SUBDEV_ENUM_FRAME_SIZE()
ioctl handler code. enum_frame_interval
- callback for
VIDIOC_SUBDEV_ENUM_FRAME_INTERVAL()
ioctl handler code. get_fmt
- callback for
VIDIOC_SUBDEV_G_FMT()
ioctl handler code. set_fmt
- callback for
VIDIOC_SUBDEV_S_FMT()
ioctl handler code. get_selection
- callback for
VIDIOC_SUBDEV_G_SELECTION()
ioctl handler code. set_selection
- callback for
VIDIOC_SUBDEV_S_SELECTION()
ioctl handler code. get_edid
- callback for
VIDIOC_SUBDEV_G_EDID()
ioctl handler code. set_edid
- callback for
VIDIOC_SUBDEV_S_EDID()
ioctl handler code. dv_timings_cap
- callback for
VIDIOC_SUBDEV_DV_TIMINGS_CAP()
ioctl handler code. enum_dv_timings
- callback for
VIDIOC_SUBDEV_ENUM_DV_TIMINGS()
ioctl handler code. link_validate
- used by the media controller code to check if the links that belongs to a pipeline can be used for stream.
get_frame_desc
- get the current low level media bus frame parameters.
set_frame_desc
- set the low level media bus frame parameters, fd array may be adjusted by the subdev driver to device capabilities.
-
struct
v4l2_subdev_ops
¶ Subdev operations
Definition
struct v4l2_subdev_ops {
const struct v4l2_subdev_core_ops *core;
const struct v4l2_subdev_tuner_ops *tuner;
const struct v4l2_subdev_audio_ops *audio;
const struct v4l2_subdev_video_ops *video;
const struct v4l2_subdev_vbi_ops *vbi;
const struct v4l2_subdev_ir_ops *ir;
const struct v4l2_subdev_sensor_ops *sensor;
const struct v4l2_subdev_pad_ops *pad;
};
Members
core
- pointer to
struct v4l2_subdev_core_ops
. Can beNULL
tuner
- pointer to
struct v4l2_subdev_tuner_ops
. Can beNULL
audio
- pointer to
struct v4l2_subdev_audio_ops
. Can beNULL
video
- pointer to
struct v4l2_subdev_video_ops
. Can beNULL
vbi
- pointer to
struct v4l2_subdev_vbi_ops
. Can beNULL
ir
- pointer to
struct v4l2_subdev_ir_ops
. Can beNULL
sensor
- pointer to
struct v4l2_subdev_sensor_ops
. Can beNULL
pad
- pointer to
struct v4l2_subdev_pad_ops
. Can beNULL
-
struct
v4l2_subdev_internal_ops
¶ V4L2 subdev internal ops
Definition
struct v4l2_subdev_internal_ops {
int (*registered)(struct v4l2_subdev *sd);
void (*unregistered)(struct v4l2_subdev *sd);
int (*open)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh);
int (*close)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh);
void (*release)(struct v4l2_subdev *sd);
};
Members
registered
- called when this subdev is registered. When called the v4l2_dev field is set to the correct v4l2_device.
unregistered
- called when this subdev is unregistered. When called the v4l2_dev field is still set to the correct v4l2_device.
open
- called when the subdev device node is opened by an application.
close
- called when the subdev device node is closed. Please note that it is possible for close to be called after unregistered!
release
- called when the last user of the subdev device is gone. This happens after the unregistered callback and when the last open filehandle to the v4l-subdevX device node was closed. If no device node was created for this sub-device, then the release callback is called right after the unregistered callback. The release callback is typically used to free the memory containing the v4l2_subdev structure. It is almost certainly required for any sub-device that sets the V4L2_SUBDEV_FL_HAS_DEVNODE flag.
Description
Note
Never call this from drivers, only the v4l2 framework can call these ops.
-
struct
v4l2_subdev_platform_data
¶ regulators config struct
Definition
struct v4l2_subdev_platform_data {
struct regulator_bulk_data *regulators;
int num_regulators;
void *host_priv;
};
Members
regulators
- Optional regulators used to power on/off the subdevice
num_regulators
- Number of regululators
host_priv
- Per-subdevice data, specific for a certain video host device
-
struct
v4l2_subdev
¶ describes a V4L2 sub-device
Definition
struct v4l2_subdev {
#if defined(CONFIG_MEDIA_CONTROLLER);
struct media_entity entity;
#endif;
struct list_head list;
struct module *owner;
bool owner_v4l2_dev;
u32 flags;
struct v4l2_device *v4l2_dev;
const struct v4l2_subdev_ops *ops;
const struct v4l2_subdev_internal_ops *internal_ops;
struct v4l2_ctrl_handler *ctrl_handler;
char name[V4L2_SUBDEV_NAME_SIZE];
u32 grp_id;
void *dev_priv;
void *host_priv;
struct video_device *devnode;
struct device *dev;
struct fwnode_handle *fwnode;
struct list_head async_list;
struct v4l2_async_subdev *asd;
struct v4l2_async_notifier *notifier;
struct v4l2_async_notifier *subdev_notifier;
struct v4l2_subdev_platform_data *pdata;
};
Members
entity
- pointer to
struct media_entity
list
- List of sub-devices
owner
- The owner is the same as the driver’s
struct device
owner. owner_v4l2_dev
- true if the
sd->owner
matches the owner of v4l2_dev->dev owner. Initialized byv4l2_device_register_subdev()
. flags
- subdev flags. Can be:
V4L2_SUBDEV_FL_IS_I2C
- Set this flag if this subdev is a i2c device;V4L2_SUBDEV_FL_IS_SPI
- Set this flag if this subdev is a spi device;V4L2_SUBDEV_FL_HAS_DEVNODE
- Set this flag if this subdev needs a device node;V4L2_SUBDEV_FL_HAS_EVENTS
- Set this flag if this subdev generates events. v4l2_dev
- pointer to struct
v4l2_device
ops
- pointer to struct
v4l2_subdev_ops
internal_ops
- pointer to struct
v4l2_subdev_internal_ops
. Never call these internal ops from within a driver! ctrl_handler
- The control handler of this subdev. May be NULL.
name
- Name of the sub-device. Please notice that the name must be unique.
grp_id
- can be used to group similar subdevs. Value is driver-specific
dev_priv
- pointer to private data
host_priv
- pointer to private data used by the device where the subdev is attached.
devnode
- subdev device node
dev
- pointer to the physical device, if any
fwnode
- The fwnode_handle of the subdev, usually the same as either dev->of_node->fwnode or dev->fwnode (whichever is non-NULL).
async_list
- Links this subdev to a global subdev_list or notifier->done list.
asd
- Pointer to respective
struct v4l2_async_subdev
. notifier
- Pointer to the managing notifier.
subdev_notifier
- A sub-device notifier implicitly registered for the sub- device using v4l2_device_register_sensor_subdev().
pdata
- common part of subdevice platform data
Description
Each instance of a subdev driver should create this struct, either stand-alone or embedded in a larger struct.
This structure should be initialized by v4l2_subdev_init()
or one of
its variants: v4l2_spi_subdev_init()
, v4l2_i2c_subdev_init()
.
-
media_entity_to_v4l2_subdev
(ent)¶ Returns a
struct v4l2_subdev
from thestruct media_entity
embedded in it.
Parameters
ent
- pointer to
struct media_entity
.
-
vdev_to_v4l2_subdev
(vdev)¶ Returns a
struct v4l2_subdev
from thestruct video_device
embedded on it.
Parameters
vdev
- pointer to
struct video_device
-
struct
v4l2_subdev_fh
¶ Used for storing subdev information per file handle
Definition
struct v4l2_subdev_fh {
struct v4l2_fh vfh;
struct module *owner;
#if defined(CONFIG_VIDEO_V4L2_SUBDEV_API);
struct v4l2_subdev_pad_config *pad;
#endif;
};
Members
vfh
- pointer to
struct v4l2_fh
owner
- module pointer to the owner of this file handle
pad
- pointer to
struct v4l2_subdev_pad_config
-
to_v4l2_subdev_fh
(fh)¶ Returns a
struct v4l2_subdev_fh
from thestruct v4l2_fh
embedded on it.
Parameters
fh
- pointer to
struct v4l2_fh
-
struct v4l2_mbus_framefmt *
v4l2_subdev_get_try_format
(struct v4l2_subdev * sd, struct v4l2_subdev_pad_config * cfg, unsigned int pad)¶ ancillary routine to call
struct v4l2_subdev_pad_config
->try_fmt
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
struct v4l2_subdev_pad_config * cfg
- pointer to
struct v4l2_subdev_pad_config
array. unsigned int pad
- index of the pad in the cfg array.
-
struct v4l2_rect *
v4l2_subdev_get_try_crop
(struct v4l2_subdev * sd, struct v4l2_subdev_pad_config * cfg, unsigned int pad)¶ ancillary routine to call
struct v4l2_subdev_pad_config
->try_crop
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
struct v4l2_subdev_pad_config * cfg
- pointer to
struct v4l2_subdev_pad_config
array. unsigned int pad
- index of the pad in the cfg array.
-
struct v4l2_rect *
v4l2_subdev_get_try_compose
(struct v4l2_subdev * sd, struct v4l2_subdev_pad_config * cfg, unsigned int pad)¶ ancillary routine to call
struct v4l2_subdev_pad_config
->try_compose
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
struct v4l2_subdev_pad_config * cfg
- pointer to
struct v4l2_subdev_pad_config
array. unsigned int pad
- index of the pad in the cfg array.
-
void
v4l2_set_subdevdata
(struct v4l2_subdev * sd, void * p)¶ Sets V4L2 dev private device data
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
void * p
- pointer to the private device data to be stored.
-
void *
v4l2_get_subdevdata
(const struct v4l2_subdev * sd)¶ Gets V4L2 dev private device data
Parameters
const struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
Description
Returns the pointer to the private device data to be stored.
-
void
v4l2_set_subdev_hostdata
(struct v4l2_subdev * sd, void * p)¶ Sets V4L2 dev private host data
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
void * p
- pointer to the private data to be stored.
-
void *
v4l2_get_subdev_hostdata
(const struct v4l2_subdev * sd)¶ Gets V4L2 dev private data
Parameters
const struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
Description
Returns the pointer to the private host data to be stored.
-
int
v4l2_subdev_link_validate_default
(struct v4l2_subdev * sd, struct media_link * link, struct v4l2_subdev_format * source_fmt, struct v4l2_subdev_format * sink_fmt)¶ validates a media link
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
struct media_link * link
- pointer to
struct media_link
struct v4l2_subdev_format * source_fmt
- pointer to
struct v4l2_subdev_format
struct v4l2_subdev_format * sink_fmt
- pointer to
struct v4l2_subdev_format
Description
This function ensures that width, height and the media bus pixel code are equal on both source and sink of the link.
-
int
v4l2_subdev_link_validate
(struct media_link * link)¶ validates a media link
Parameters
struct media_link * link
- pointer to
struct media_link
Description
This function calls the subdev’s link_validate ops to validate
if a media link is valid for streaming. It also internally
calls v4l2_subdev_link_validate_default()
to ensure that
width, height and the media bus pixel code are equal on both
source and sink of the link.
-
struct v4l2_subdev_pad_config *
v4l2_subdev_alloc_pad_config
(struct v4l2_subdev * sd)¶ Allocates memory for pad config
Parameters
struct v4l2_subdev * sd
- pointer to struct v4l2_subdev
-
void
v4l2_subdev_free_pad_config
(struct v4l2_subdev_pad_config * cfg)¶ Frees memory allocated by
v4l2_subdev_alloc_pad_config()
.
Parameters
struct v4l2_subdev_pad_config * cfg
- pointer to
struct v4l2_subdev_pad_config
-
void
v4l2_subdev_init
(struct v4l2_subdev * sd, const struct v4l2_subdev_ops * ops)¶ initializes the sub-device struct
Parameters
struct v4l2_subdev * sd
- pointer to the
struct v4l2_subdev
to be initialized const struct v4l2_subdev_ops * ops
- pointer to
struct v4l2_subdev_ops
.
-
v4l2_subdev_call
(sd, o, f, args)¶ call an operation of a v4l2_subdev.
Parameters
sd
- pointer to the
struct v4l2_subdev
o
- name of the element at
struct v4l2_subdev_ops
that contains f. Each element there groups a set of callbacks functions. f
- callback function to be called.
The callback functions are defined in groups, according to
each element at
struct v4l2_subdev_ops
. args
- arguments for f.
Example
err = v4l2_subdev_call(sd, video, s_std, norm);
-
v4l2_subdev_has_op
(sd, o, f)¶ Checks if a subdev defines a certain operation.
Parameters
sd
- pointer to the
struct v4l2_subdev
o
- The group of callback functions in
struct v4l2_subdev_ops
which f is a part of. f
- callback function to be checked for its existence.
-
void
v4l2_subdev_notify_event
(struct v4l2_subdev * sd, const struct v4l2_event * ev)¶ Delivers event notification for subdevice
Parameters
struct v4l2_subdev * sd
- The subdev for which to deliver the event
const struct v4l2_event * ev
- The event to deliver
Description
Will deliver the specified event to all userspace event listeners which are
subscribed to the v42l subdev event queue as well as to the bridge driver
using the notify callback. The notification type for the notify callback
will be V4L2_DEVICE_NOTIFY_EVENT
.
-
enum
v4l2_async_match_type
¶ type of asynchronous subdevice logic to be used in order to identify a match
Constants
V4L2_ASYNC_MATCH_CUSTOM
- Match will use the logic provided by
struct v4l2_async_subdev
.match ops V4L2_ASYNC_MATCH_DEVNAME
- Match will use the device name
V4L2_ASYNC_MATCH_I2C
- Match will check for I2C adapter ID and address
V4L2_ASYNC_MATCH_FWNODE
- Match will use firmware node
Description
This enum is used by the asyncrhronous sub-device logic to define the algorithm that will be used to match an asynchronous device.
-
struct
v4l2_async_subdev
¶ sub-device descriptor, as known to a bridge
Definition
struct v4l2_async_subdev {
enum v4l2_async_match_type match_type;
union {
struct fwnode_handle *fwnode;
const char *device_name;
struct {
int adapter_id;
unsigned short address;
} i2c;
struct {
bool (*match)(struct device *dev, struct v4l2_async_subdev *sd);
void *priv;
} custom;
} match;
struct list_head list;
struct list_head asd_list;
};
Members
match_type
- type of match that will be used
match
- union of per-bus type matching data sets
match.fwnode
- pointer to
struct fwnode_handle
to be matched. Used if match_type isV4L2_ASYNC_MATCH_FWNODE
. match.device_name
- string containing the device name to be matched.
Used if match_type is
V4L2_ASYNC_MATCH_DEVNAME
. match.i2c
- embedded struct with I2C parameters to be matched.
Both match.i2c.adapter_id and match.i2c.address
should be matched.
Used if match_type is
V4L2_ASYNC_MATCH_I2C
. match.i2c.adapter_id
- I2C adapter ID to be matched.
Used if match_type is
V4L2_ASYNC_MATCH_I2C
. match.i2c.address
- I2C address to be matched.
Used if match_type is
V4L2_ASYNC_MATCH_I2C
. match.custom
- Driver-specific match criteria.
Used if match_type is
V4L2_ASYNC_MATCH_CUSTOM
. match.custom.match
- Driver-specific match function to be used if
V4L2_ASYNC_MATCH_CUSTOM
. match.custom.priv
- Driver-specific private struct with match parameters
to be used if
V4L2_ASYNC_MATCH_CUSTOM
. list
- used to link struct v4l2_async_subdev objects, waiting to be probed, to a notifier->waiting list
asd_list
- used to add struct v4l2_async_subdev objects to the master notifier asd_list
Description
When this struct is used as a member in a driver specific struct,
the driver specific struct shall contain the struct
v4l2_async_subdev
as its first member.
-
struct
v4l2_async_notifier_operations
¶ Asynchronous V4L2 notifier operations
Definition
struct v4l2_async_notifier_operations {
int (*bound)(struct v4l2_async_notifier *notifier,struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd);
int (*complete)(struct v4l2_async_notifier *notifier);
void (*unbind)(struct v4l2_async_notifier *notifier,struct v4l2_subdev *subdev, struct v4l2_async_subdev *asd);
};
Members
bound
- a subdevice driver has successfully probed one of the subdevices
complete
- All subdevices have been probed successfully. The complete callback is only executed for the root notifier.
unbind
- a subdevice is leaving
-
struct
v4l2_async_notifier
¶ v4l2_device notifier data
Definition
struct v4l2_async_notifier {
const struct v4l2_async_notifier_operations *ops;
struct v4l2_device *v4l2_dev;
struct v4l2_subdev *sd;
struct v4l2_async_notifier *parent;
struct list_head asd_list;
struct list_head waiting;
struct list_head done;
struct list_head list;
};
Members
ops
- notifier operations
v4l2_dev
- v4l2_device of the root notifier, NULL otherwise
sd
- sub-device that registered the notifier, NULL otherwise
parent
- parent notifier
asd_list
- master list of struct v4l2_async_subdev
waiting
- list of struct v4l2_async_subdev, waiting for their drivers
done
- list of struct v4l2_subdev, already probed
list
- member in a global list of notifiers
-
void
v4l2_async_notifier_init
(struct v4l2_async_notifier * notifier)¶ Initialize a notifier.
Parameters
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
Description
This function initializes the notifier asd_list. It must be called before the first call to v4l2_async_notifier_add_subdev.
-
int
v4l2_async_notifier_add_subdev
(struct v4l2_async_notifier * notifier, struct v4l2_async_subdev * asd)¶ Add an async subdev to the notifier’s master asd list.
Parameters
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
struct v4l2_async_subdev * asd
- pointer to
struct v4l2_async_subdev
Description
Call this function before registering a notifier to link the provided asd to the notifiers master asd_list.
-
struct v4l2_async_subdev *
v4l2_async_notifier_add_fwnode_subdev
(struct v4l2_async_notifier * notifier, struct fwnode_handle * fwnode, unsigned int asd_struct_size)¶ Allocate and add a fwnode async subdev to the notifier’s master asd_list.
Parameters
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
struct fwnode_handle * fwnode
- fwnode handle of the sub-device to be matched
unsigned int asd_struct_size
- size of the driver’s async sub-device struct, including
sizeof(struct v4l2_async_subdev). The
struct v4l2_async_subdev
shall be the first member of the driver’s async sub-device struct, i.e. both begin at the same memory address.
Description
Allocate a fwnode-matched asd of size asd_struct_size, and add it to the notifiers asd_list. The function also gets a reference of the fwnode which is released later at notifier cleanup time.
-
int
v4l2_async_notifier_add_fwnode_remote_subdev
(struct v4l2_async_notifier * notif, struct fwnode_handle * endpoint, struct v4l2_async_subdev * asd)¶ Allocate and add a fwnode remote async subdev to the notifier’s master asd_list.
Parameters
struct v4l2_async_notifier * notif
- pointer to
struct v4l2_async_notifier
struct fwnode_handle * endpoint
- local endpoint pointing to the remote sub-device to be matched
struct v4l2_async_subdev * asd
- Async sub-device struct allocated by the caller. The
struct v4l2_async_subdev
shall be the first member of the driver’s async sub-device struct, i.e. both begin at the same memory address.
Description
Gets the remote endpoint of a given local endpoint, set it up for fwnode matching and adds the async sub-device to the notifier’s asd_list. The function also gets a reference of the fwnode which is released later at notifier cleanup time.
This is just like v4l2_async_notifier_add_fwnode_subdev, but with the exception that the fwnode refers to a local endpoint, not the remote one, and the function relies on the caller to allocate the async sub-device struct.
-
struct v4l2_async_subdev *
v4l2_async_notifier_add_i2c_subdev
(struct v4l2_async_notifier * notifier, int adapter_id, unsigned short address, unsigned int asd_struct_size)¶ Allocate and add an i2c async subdev to the notifier’s master asd_list.
Parameters
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
int adapter_id
- I2C adapter ID to be matched
unsigned short address
- I2C address of sub-device to be matched
unsigned int asd_struct_size
- size of the driver’s async sub-device struct, including
sizeof(struct v4l2_async_subdev). The
struct v4l2_async_subdev
shall be the first member of the driver’s async sub-device struct, i.e. both begin at the same memory address.
Description
Same as above but for I2C matched sub-devices.
-
struct v4l2_async_subdev *
v4l2_async_notifier_add_devname_subdev
(struct v4l2_async_notifier * notifier, const char * device_name, unsigned int asd_struct_size)¶ Allocate and add a device-name async subdev to the notifier’s master asd_list.
Parameters
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
const char * device_name
- device name string to be matched
unsigned int asd_struct_size
- size of the driver’s async sub-device struct, including
sizeof(struct v4l2_async_subdev). The
struct v4l2_async_subdev
shall be the first member of the driver’s async sub-device struct, i.e. both begin at the same memory address.
Description
Same as above but for device-name matched sub-devices.
-
int
v4l2_async_notifier_register
(struct v4l2_device * v4l2_dev, struct v4l2_async_notifier * notifier)¶ registers a subdevice asynchronous notifier
Parameters
struct v4l2_device * v4l2_dev
- pointer to
struct v4l2_device
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
-
int
v4l2_async_subdev_notifier_register
(struct v4l2_subdev * sd, struct v4l2_async_notifier * notifier)¶ registers a subdevice asynchronous notifier for a sub-device
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
-
void
v4l2_async_notifier_unregister
(struct v4l2_async_notifier * notifier)¶ unregisters a subdevice asynchronous notifier
Parameters
struct v4l2_async_notifier * notifier
- pointer to
struct v4l2_async_notifier
-
void
v4l2_async_notifier_cleanup
(struct v4l2_async_notifier * notifier)¶ clean up notifier resources
Parameters
struct v4l2_async_notifier * notifier
- the notifier the resources of which are to be cleaned up
Description
Release memory resources related to a notifier, including the async sub-devices allocated for the purposes of the notifier but not the notifier itself. The user is responsible for calling this function to clean up the notifier after calling v4l2_async_notifier_add_subdev, v4l2_async_notifier_parse_fwnode_endpoints or v4l2_fwnode_reference_parse_sensor_common.
There is no harm from calling v4l2_async_notifier_cleanup in other cases as long as its memory has been zeroed after it has been allocated.
-
int
v4l2_async_register_subdev
(struct v4l2_subdev * sd)¶ registers a sub-device to the asynchronous subdevice framework
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev
-
int
v4l2_async_register_subdev_sensor_common
(struct v4l2_subdev * sd)¶ registers a sensor sub-device to the asynchronous sub-device framework and parse set up common sensor related devices
Parameters
struct v4l2_subdev * sd
- pointer to struct
v4l2_subdev
Description
This function is just like v4l2_async_register_subdev()
with the exception
that calling it will also parse firmware interfaces for remote references
using v4l2_async_notifier_parse_fwnode_sensor_common()
and registers the
async sub-devices. The sub-device is similarly unregistered by calling
v4l2_async_unregister_subdev()
.
While registered, the subdev module is marked as in-use.
An error is returned if the module is no longer loaded on any attempts to register it.
-
void
v4l2_async_unregister_subdev
(struct v4l2_subdev * sd)¶ unregisters a sub-device to the asynchronous subdevice framework
Parameters
struct v4l2_subdev * sd
- pointer to
struct v4l2_subdev