net: dsa: mt7530: refactor MT7530_PMCR_P()

The MT7530_PMCR_P() registers are on MT7530, MT7531, and the switch on the
MT7988 SoC. Rename the definition for them to MT753X_PMCR_P(). Bit 15 is
for MT7530 only. Add MT7530 prefix to the definition for bit 15.

Use GENMASK and FIELD_PREP for PMCR_IFG_XMIT().

Rename PMCR_TX_EN and PMCR_RX_EN to PMCR_MAC_TX_EN and PMCR_MAC_TX_EN to
follow the naming on the "MT7621 Giga Switch Programming Guide v0.3",
"MT7531 Reference Manual for Development Board v1.0", and "MT7988A Wi-Fi 7
Generation Router Platform: Datasheet (Open Version) v0.1" documents.

These documents show that PMCR_RX_FC_EN is at bit 5. Correct this along
with renaming it to PMCR_FORCE_RX_FC_EN, and the same for PMCR_TX_FC_EN.

Remove PMCR_SPEED_MASK which doesn't have a use.

Rename the force mode definitions for MT7531 to FORCE_MODE. Add MASK at the
end for the mask that includes all force mode definitions.

Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

2 files changed, 42 insertions, 40 deletions

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 04795ef8ebd774..8dee9cee1104f7 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -896,7 +896,7 @@ static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
 		val &= ~MHWTRAP_P5_MAC_SEL & ~MHWTRAP_P5_DIS;
 
 		/* Setup the MAC by default for the cpu port */
-		mt7530_write(priv, MT7530_PMCR_P(5), 0x56300);
+		mt7530_write(priv, MT753X_PMCR_P(5), 0x56300);
 		break;
 	case P5_INTF_SEL_GMAC5:
 		/* MT7530_P5_MODE_GMAC: P5 -> External phy or 2nd GMAC */
@@ -2444,8 +2444,8 @@ mt7530_setup(struct dsa_switch *ds)
 		/* Clear link settings and enable force mode to force link down
 		 * on all ports until they're enabled later.
 		 */
-		mt7530_rmw(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
-			   PMCR_FORCE_MODE, PMCR_FORCE_MODE);
+		mt7530_rmw(priv, MT753X_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
+			   MT7530_FORCE_MODE, MT7530_FORCE_MODE);
 
 		/* Disable forwarding by default on all ports */
 		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
@@ -2555,8 +2555,8 @@ mt7531_setup_common(struct dsa_switch *ds)
 		/* Clear link settings and enable force mode to force link down
 		 * on all ports until they're enabled later.
 		 */
-		mt7530_rmw(priv, MT7530_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
-			   MT7531_FORCE_MODE, MT7531_FORCE_MODE);
+		mt7530_rmw(priv, MT753X_PMCR_P(i), PMCR_LINK_SETTINGS_MASK |
+			   MT7531_FORCE_MODE_MASK, MT7531_FORCE_MODE_MASK);
 
 		/* Disable forwarding by default on all ports */
 		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
@@ -2639,7 +2639,7 @@ mt7531_setup(struct dsa_switch *ds)
 
 	/* Force link down on all ports before internal reset */
 	for (i = 0; i < MT7530_NUM_PORTS; i++)
-		mt7530_write(priv, MT7530_PMCR_P(i), MT7531_FORCE_LNK);
+		mt7530_write(priv, MT753X_PMCR_P(i), MT7531_FORCE_MODE_LNK);
 
 	/* Reset the switch through internal reset */
 	mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_SW_RST | SYS_CTRL_REG_RST);
@@ -2881,7 +2881,7 @@ mt753x_phylink_mac_config(struct phylink_config *config, unsigned int mode,
 
 	/* Are we connected to external phy */
 	if (port == 5 && dsa_is_user_port(ds, 5))
-		mt7530_set(priv, MT7530_PMCR_P(port), PMCR_EXT_PHY);
+		mt7530_set(priv, MT753X_PMCR_P(port), PMCR_EXT_PHY);
 }
 
 static void mt753x_phylink_mac_link_down(struct phylink_config *config,
@@ -2891,7 +2891,7 @@ static void mt753x_phylink_mac_link_down(struct phylink_config *config,
 	struct dsa_port *dp = dsa_phylink_to_port(config);
 	struct mt7530_priv *priv = dp->ds->priv;
 
-	mt7530_clear(priv, MT7530_PMCR_P(dp->index), PMCR_LINK_SETTINGS_MASK);
+	mt7530_clear(priv, MT753X_PMCR_P(dp->index), PMCR_LINK_SETTINGS_MASK);
 }
 
 static void mt753x_phylink_mac_link_up(struct phylink_config *config,
@@ -2905,7 +2905,7 @@ static void mt753x_phylink_mac_link_up(struct phylink_config *config,
 	struct mt7530_priv *priv = dp->ds->priv;
 	u32 mcr;
 
-	mcr = PMCR_RX_EN | PMCR_TX_EN | PMCR_FORCE_LNK;
+	mcr = PMCR_MAC_RX_EN | PMCR_MAC_TX_EN | PMCR_FORCE_LNK;
 
 	switch (speed) {
 	case SPEED_1000:
@@ -2920,9 +2920,9 @@ static void mt753x_phylink_mac_link_up(struct phylink_config *config,
 	if (duplex == DUPLEX_FULL) {
 		mcr |= PMCR_FORCE_FDX;
 		if (tx_pause)
-			mcr |= PMCR_TX_FC_EN;
+			mcr |= PMCR_FORCE_TX_FC_EN;
 		if (rx_pause)
-			mcr |= PMCR_RX_FC_EN;
+			mcr |= PMCR_FORCE_RX_FC_EN;
 	}
 
 	if (mode == MLO_AN_PHY && phydev && phy_init_eee(phydev, false) >= 0) {
@@ -2937,7 +2937,7 @@ static void mt753x_phylink_mac_link_up(struct phylink_config *config,
 		}
 	}
 
-	mt7530_set(priv, MT7530_PMCR_P(dp->index), mcr);
+	mt7530_set(priv, MT753X_PMCR_P(dp->index), mcr);
 }
 
 static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index f7c5355c16420b..7d7abb67202f17 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -304,44 +304,46 @@ enum mt7530_vlan_port_acc_frm {
 #define  G0_PORT_VID_DEF		G0_PORT_VID(0)
 
 /* Register for port MAC control register */
-#define MT7530_PMCR_P(x)		(0x3000 + ((x) * 0x100))
-#define  PMCR_IFG_XMIT(x)		(((x) & 0x3) << 18)
+#define MT753X_PMCR_P(x)		(0x3000 + ((x) * 0x100))
+#define  PMCR_IFG_XMIT_MASK		GENMASK(19, 18)
+#define  PMCR_IFG_XMIT(x)		FIELD_PREP(PMCR_IFG_XMIT_MASK, x)
 #define  PMCR_EXT_PHY			BIT(17)
 #define  PMCR_MAC_MODE			BIT(16)
-#define  PMCR_FORCE_MODE		BIT(15)
-#define  PMCR_TX_EN			BIT(14)
-#define  PMCR_RX_EN			BIT(13)
+#define  MT7530_FORCE_MODE		BIT(15)
+#define  PMCR_MAC_TX_EN			BIT(14)
+#define  PMCR_MAC_RX_EN			BIT(13)
 #define  PMCR_BACKOFF_EN		BIT(9)
 #define  PMCR_BACKPR_EN			BIT(8)
 #define  PMCR_FORCE_EEE1G		BIT(7)
 #define  PMCR_FORCE_EEE100		BIT(6)
-#define  PMCR_TX_FC_EN			BIT(5)
-#define  PMCR_RX_FC_EN			BIT(4)
+#define  PMCR_FORCE_RX_FC_EN		BIT(5)
+#define  PMCR_FORCE_TX_FC_EN		BIT(4)
 #define  PMCR_FORCE_SPEED_1000		BIT(3)
 #define  PMCR_FORCE_SPEED_100		BIT(2)
 #define  PMCR_FORCE_FDX			BIT(1)
 #define  PMCR_FORCE_LNK			BIT(0)
-#define  PMCR_SPEED_MASK		(PMCR_FORCE_SPEED_100 | \
-					 PMCR_FORCE_SPEED_1000)
-#define  MT7531_FORCE_LNK		BIT(31)
-#define  MT7531_FORCE_SPD		BIT(30)
-#define  MT7531_FORCE_DPX		BIT(29)
-#define  MT7531_FORCE_RX_FC		BIT(28)
-#define  MT7531_FORCE_TX_FC		BIT(27)
-#define  MT7531_FORCE_EEE100		BIT(26)
-#define  MT7531_FORCE_EEE1G		BIT(25)
-#define  MT7531_FORCE_MODE		(MT7531_FORCE_LNK | \
-					 MT7531_FORCE_SPD | \
-					 MT7531_FORCE_DPX | \
-					 MT7531_FORCE_RX_FC | \
-					 MT7531_FORCE_TX_FC | \
-					 MT7531_FORCE_EEE100 | \
-					 MT7531_FORCE_EEE1G)
-#define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
-					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
-					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
-					 PMCR_FORCE_FDX | PMCR_FORCE_LNK | \
-					 PMCR_FORCE_EEE1G | PMCR_FORCE_EEE100)
+#define  MT7531_FORCE_MODE_LNK		BIT(31)
+#define  MT7531_FORCE_MODE_SPD		BIT(30)
+#define  MT7531_FORCE_MODE_DPX		BIT(29)
+#define  MT7531_FORCE_MODE_RX_FC	BIT(28)
+#define  MT7531_FORCE_MODE_TX_FC	BIT(27)
+#define  MT7531_FORCE_MODE_EEE100	BIT(26)
+#define  MT7531_FORCE_MODE_EEE1G	BIT(25)
+#define  MT7531_FORCE_MODE_MASK		(MT7531_FORCE_MODE_LNK | \
+					 MT7531_FORCE_MODE_SPD | \
+					 MT7531_FORCE_MODE_DPX | \
+					 MT7531_FORCE_MODE_RX_FC | \
+					 MT7531_FORCE_MODE_TX_FC | \
+					 MT7531_FORCE_MODE_EEE100 | \
+					 MT7531_FORCE_MODE_EEE1G)
+#define  PMCR_LINK_SETTINGS_MASK	(PMCR_MAC_TX_EN | PMCR_MAC_RX_EN | \
+					 PMCR_FORCE_EEE1G | \
+					 PMCR_FORCE_EEE100 | \
+					 PMCR_FORCE_RX_FC_EN | \
+					 PMCR_FORCE_TX_FC_EN | \
+					 PMCR_FORCE_SPEED_1000 | \
+					 PMCR_FORCE_SPEED_100 | \
+					 PMCR_FORCE_FDX | PMCR_FORCE_LNK)
 
 #define MT7530_PMEEECR_P(x)		(0x3004 + (x) * 0x100)
 #define  WAKEUP_TIME_1000(x)		(((x) & 0xFF) << 24)