diff options
Diffstat (limited to 'drivers/usb/host/xhci-port.h')
| -rw-r--r-- | drivers/usb/host/xhci-port.h | 176 |
1 files changed, 176 insertions, 0 deletions
diff --git a/drivers/usb/host/xhci-port.h b/drivers/usb/host/xhci-port.h new file mode 100644 index 00000000000000..f19efb966d180c --- /dev/null +++ b/drivers/usb/host/xhci-port.h @@ -0,0 +1,176 @@ +/* SPDX-License-Identifier: GPL-2.0 */ + +/* PORTSC - Port Status and Control Register - port_status_base bitmasks */ +/* true: device connected */ +#define PORT_CONNECT (1 << 0) +/* true: port enabled */ +#define PORT_PE (1 << 1) +/* bit 2 reserved and zeroed */ +/* true: port has an over-current condition */ +#define PORT_OC (1 << 3) +/* true: port reset signaling asserted */ +#define PORT_RESET (1 << 4) +/* Port Link State - bits 5:8 + * A read gives the current link PM state of the port, + * a write with Link State Write Strobe set sets the link state. + */ +#define PORT_PLS_MASK (0xf << 5) +#define XDEV_U0 (0x0 << 5) +#define XDEV_U1 (0x1 << 5) +#define XDEV_U2 (0x2 << 5) +#define XDEV_U3 (0x3 << 5) +#define XDEV_DISABLED (0x4 << 5) +#define XDEV_RXDETECT (0x5 << 5) +#define XDEV_INACTIVE (0x6 << 5) +#define XDEV_POLLING (0x7 << 5) +#define XDEV_RECOVERY (0x8 << 5) +#define XDEV_HOT_RESET (0x9 << 5) +#define XDEV_COMP_MODE (0xa << 5) +#define XDEV_TEST_MODE (0xb << 5) +#define XDEV_RESUME (0xf << 5) + +/* true: port has power (see HCC_PPC) */ +#define PORT_POWER (1 << 9) +/* bits 10:13 indicate device speed: + * 0 - undefined speed - port hasn't be initialized by a reset yet + * 1 - full speed + * 2 - low speed + * 3 - high speed + * 4 - super speed + * 5-15 reserved + */ +#define DEV_SPEED_MASK (0xf << 10) +#define XDEV_FS (0x1 << 10) +#define XDEV_LS (0x2 << 10) +#define XDEV_HS (0x3 << 10) +#define XDEV_SS (0x4 << 10) +#define XDEV_SSP (0x5 << 10) +#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10)) +#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS) +#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS) +#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS) +#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS) +#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP) +#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS) +#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f) + +/* Bits 20:23 in the Slot Context are the speed for the device */ +#define SLOT_SPEED_FS (XDEV_FS << 10) +#define SLOT_SPEED_LS (XDEV_LS << 10) +#define SLOT_SPEED_HS (XDEV_HS << 10) +#define SLOT_SPEED_SS (XDEV_SS << 10) +#define SLOT_SPEED_SSP (XDEV_SSP << 10) +/* Port Indicator Control */ +#define PORT_LED_OFF (0 << 14) +#define PORT_LED_AMBER (1 << 14) +#define PORT_LED_GREEN (2 << 14) +#define PORT_LED_MASK (3 << 14) +/* Port Link State Write Strobe - set this when changing link state */ +#define PORT_LINK_STROBE (1 << 16) +/* true: connect status change */ +#define PORT_CSC (1 << 17) +/* true: port enable change */ +#define PORT_PEC (1 << 18) +/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port + * into an enabled state, and the device into the default state. A "warm" reset + * also resets the link, forcing the device through the link training sequence. + * SW can also look at the Port Reset register to see when warm reset is done. + */ +#define PORT_WRC (1 << 19) +/* true: over-current change */ +#define PORT_OCC (1 << 20) +/* true: reset change - 1 to 0 transition of PORT_RESET */ +#define PORT_RC (1 << 21) +/* port link status change - set on some port link state transitions: + * Transition Reason + * ------------------------------------------------------------------------------ + * - U3 to Resume Wakeup signaling from a device + * - Resume to Recovery to U0 USB 3.0 device resume + * - Resume to U0 USB 2.0 device resume + * - U3 to Recovery to U0 Software resume of USB 3.0 device complete + * - U3 to U0 Software resume of USB 2.0 device complete + * - U2 to U0 L1 resume of USB 2.1 device complete + * - U0 to U0 (???) L1 entry rejection by USB 2.1 device + * - U0 to disabled L1 entry error with USB 2.1 device + * - Any state to inactive Error on USB 3.0 port + */ +#define PORT_PLC (1 << 22) +/* port configure error change - port failed to configure its link partner */ +#define PORT_CEC (1 << 23) +#define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \ + PORT_RC | PORT_PLC | PORT_CEC) + + +/* Cold Attach Status - xHC can set this bit to report device attached during + * Sx state. Warm port reset should be perfomed to clear this bit and move port + * to connected state. + */ +#define PORT_CAS (1 << 24) +/* wake on connect (enable) */ +#define PORT_WKCONN_E (1 << 25) +/* wake on disconnect (enable) */ +#define PORT_WKDISC_E (1 << 26) +/* wake on over-current (enable) */ +#define PORT_WKOC_E (1 << 27) +/* bits 28:29 reserved */ +/* true: device is non-removable - for USB 3.0 roothub emulation */ +#define PORT_DEV_REMOVE (1 << 30) +/* Initiate a warm port reset - complete when PORT_WRC is '1' */ +#define PORT_WR (1 << 31) + +/* We mark duplicate entries with -1 */ +#define DUPLICATE_ENTRY ((u8)(-1)) + +/* Port Power Management Status and Control - port_power_base bitmasks */ +/* Inactivity timer value for transitions into U1, in microseconds. + * Timeout can be up to 127us. 0xFF means an infinite timeout. + */ +#define PORT_U1_TIMEOUT(p) ((p) & 0xff) +#define PORT_U1_TIMEOUT_MASK 0xff +/* Inactivity timer value for transitions into U2 */ +#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8) +#define PORT_U2_TIMEOUT_MASK (0xff << 8) +/* Bits 24:31 for port testing */ + +/* USB2 Protocol PORTSPMSC */ +#define PORT_L1S_MASK 7 +#define PORT_L1S_SUCCESS 1 +#define PORT_RWE (1 << 3) +#define PORT_HIRD(p) (((p) & 0xf) << 4) +#define PORT_HIRD_MASK (0xf << 4) +#define PORT_L1DS_MASK (0xff << 8) +#define PORT_L1DS(p) (((p) & 0xff) << 8) +#define PORT_HLE (1 << 16) +#define PORT_TEST_MODE_SHIFT 28 + +/* USB3 Protocol PORTLI Port Link Information */ +#define PORT_RX_LANES(p) (((p) >> 16) & 0xf) +#define PORT_TX_LANES(p) (((p) >> 20) & 0xf) + +/* USB2 Protocol PORTHLPMC */ +#define PORT_HIRDM(p)((p) & 3) +#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2) +#define PORT_BESLD(p)(((p) & 0xf) << 10) + +/* use 512 microseconds as USB2 LPM L1 default timeout. */ +#define XHCI_L1_TIMEOUT 512 + +/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency. + * Safe to use with mixed HIRD and BESL systems (host and device) and is used + * by other operating systems. + * + * XHCI 1.0 errata 8/14/12 Table 13 notes: + * "Software should choose xHC BESL/BESLD field values that do not violate a + * device's resume latency requirements, + * e.g. not program values > '4' if BLC = '1' and a HIRD device is attached, + * or not program values < '4' if BLC = '0' and a BESL device is attached. + */ +#define XHCI_DEFAULT_BESL 4 + +/* + * USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports + * to complete link training. usually link trainig completes much faster + * so check status 10 times with 36ms sleep in places we need to wait for + * polling to complete. + */ +#define XHCI_PORT_POLLING_LFPS_TIME 36 |