Merge branch 'for-next' of git://git.linaro.org/people/triad/linux-pinctrl

* 'for-next' of git://git.linaro.org/people/triad/linux-pinctrl:
  pinctrl/sirf: fix sirfsoc_get_group_pins prototype
  pinctrl: Don't copy function name when requesting a pin
  pinctrl: Don't copy pin names when registering them
  pinctrl: Remove unsafe __refdata
  pinctrl: get_group_pins() const fixes
  pinctrl: add a driver for the CSR SiRFprimaII pinmux
  pinctrl: add a driver for the U300 pinmux
  drivers: create a pin control subsystem

23 files changed, 5708 insertions, 581 deletions

diff --git a/Documentation/pinctrl.txt b/Documentation/pinctrl.txt
new file mode 100644
index 00000000000000..b04cb7d45a1632
--- /dev/null
+++ b/Documentation/pinctrl.txt
@@ -0,0 +1,950 @@
+PINCTRL (PIN CONTROL) subsystem
+This document outlines the pin control subsystem in Linux
+
+This subsystem deals with:
+
+- Enumerating and naming controllable pins
+
+- Multiplexing of pins, pads, fingers (etc) see below for details
+
+The intention is to also deal with:
+
+- Software-controlled biasing and driving mode specific pins, such as
+  pull-up/down, open drain etc, load capacitance configuration when controlled
+  by software, etc.
+
+
+Top-level interface
+===================
+
+Definition of PIN CONTROLLER:
+
+- A pin controller is a piece of hardware, usually a set of registers, that
+  can control PINs. It may be able to multiplex, bias, set load capacitance,
+  set drive strength etc for individual pins or groups of pins.
+
+Definition of PIN:
+
+- PINS are equal to pads, fingers, balls or whatever packaging input or
+  output line you want to control and these are denoted by unsigned integers
+  in the range 0..maxpin. This numberspace is local to each PIN CONTROLLER, so
+  there may be several such number spaces in a system. This pin space may
+  be sparse - i.e. there may be gaps in the space with numbers where no
+  pin exists.
+
+When a PIN CONTROLLER is instatiated, it will register a descriptor to the
+pin control framework, and this descriptor contains an array of pin descriptors
+describing the pins handled by this specific pin controller.
+
+Here is an example of a PGA (Pin Grid Array) chip seen from underneath:
+
+        A   B   C   D   E   F   G   H
+
+   8    o   o   o   o   o   o   o   o
+
+   7    o   o   o   o   o   o   o   o
+
+   6    o   o   o   o   o   o   o   o
+
+   5    o   o   o   o   o   o   o   o
+
+   4    o   o   o   o   o   o   o   o
+
+   3    o   o   o   o   o   o   o   o
+
+   2    o   o   o   o   o   o   o   o
+
+   1    o   o   o   o   o   o   o   o
+
+To register a pin controller and name all the pins on this package we can do
+this in our driver:
+
+#include <linux/pinctrl/pinctrl.h>
+
+const struct pinctrl_pin_desc __refdata foo_pins[] = {
+      PINCTRL_PIN(0, "A1"),
+      PINCTRL_PIN(1, "A2"),
+      PINCTRL_PIN(2, "A3"),
+      ...
+      PINCTRL_PIN(61, "H6"),
+      PINCTRL_PIN(62, "H7"),
+      PINCTRL_PIN(63, "H8"),
+};
+
+static struct pinctrl_desc foo_desc = {
+	.name = "foo",
+	.pins = foo_pins,
+	.npins = ARRAY_SIZE(foo_pins),
+	.maxpin = 63,
+	.owner = THIS_MODULE,
+};
+
+int __init foo_probe(void)
+{
+	struct pinctrl_dev *pctl;
+
+	pctl = pinctrl_register(&foo_desc, <PARENT>, NULL);
+	if (IS_ERR(pctl))
+		pr_err("could not register foo pin driver\n");
+}
+
+Pins usually have fancier names than this. You can find these in the dataheet
+for your chip. Notice that the core pinctrl.h file provides a fancy macro
+called PINCTRL_PIN() to create the struct entries. As you can see I enumerated
+the pins from 0 in the upper left corner to 63 in the lower right corner,
+this enumeration was arbitrarily chosen, in practice you need to think
+through your numbering system so that it matches the layout of registers
+and such things in your driver, or the code may become complicated. You must
+also consider matching of offsets to the GPIO ranges that may be handled by
+the pin controller.
+
+For a padring with 467 pads, as opposed to actual pins, I used an enumeration
+like this, walking around the edge of the chip, which seems to be industry
+standard too (all these pads had names, too):
+
+
+     0 ..... 104
+   466        105
+     .        .
+     .        .
+   358        224
+    357 .... 225
+
+
+Pin groups
+==========
+
+Many controllers need to deal with groups of pins, so the pin controller
+subsystem has a mechanism for enumerating groups of pins and retrieving the
+actual enumerated pins that are part of a certain group.
+
+For example, say that we have a group of pins dealing with an SPI interface
+on { 0, 8, 16, 24 }, and a group of pins dealing with an I2C interface on pins
+on { 24, 25 }.
+
+These two groups are presented to the pin control subsystem by implementing
+some generic pinctrl_ops like this:
+
+#include <linux/pinctrl/pinctrl.h>
+
+struct foo_group {
+	const char *name;
+	const unsigned int *pins;
+	const unsigned num_pins;
+};
+
+static unsigned int spi0_pins[] = { 0, 8, 16, 24 };
+static unsigned int i2c0_pins[] = { 24, 25 };
+
+static const struct foo_group foo_groups[] = {
+	{
+		.name = "spi0_grp",
+		.pins = spi0_pins,
+		.num_pins = ARRAY_SIZE(spi0_pins),
+	},
+	{
+		.name = "i2c0_grp",
+		.pins = i2c0_pins,
+		.num_pins = ARRAY_SIZE(i2c0_pins),
+	},
+};
+
+
+static int foo_list_groups(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(foo_groups))
+		return -EINVAL;
+	return 0;
+}
+
+static const char *foo_get_group_name(struct pinctrl_dev *pctldev,
+				       unsigned selector)
+{
+	return foo_groups[selector].name;
+}
+
+static int foo_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
+			       unsigned ** const pins,
+			       unsigned * const num_pins)
+{
+	*pins = (unsigned *) foo_groups[selector].pins;
+	*num_pins = foo_groups[selector].num_pins;
+	return 0;
+}
+
+static struct pinctrl_ops foo_pctrl_ops = {
+	.list_groups = foo_list_groups,
+	.get_group_name = foo_get_group_name,
+	.get_group_pins = foo_get_group_pins,
+};
+
+
+static struct pinctrl_desc foo_desc = {
+       ...
+       .pctlops = &foo_pctrl_ops,
+};
+
+The pin control subsystem will call the .list_groups() function repeatedly
+beginning on 0 until it returns non-zero to determine legal selectors, then
+it will call the other functions to retrieve the name and pins of the group.
+Maintaining the data structure of the groups is up to the driver, this is
+just a simple example - in practice you may need more entries in your group
+structure, for example specific register ranges associated with each group
+and so on.
+
+
+Interaction with the GPIO subsystem
+===================================
+
+The GPIO drivers may want to perform operations of various types on the same
+physical pins that are also registered as pin controller pins.
+
+Since the pin controller subsystem have its pinspace local to the pin
+controller we need a mapping so that the pin control subsystem can figure out
+which pin controller handles control of a certain GPIO pin. Since a single
+pin controller may be muxing several GPIO ranges (typically SoCs that have
+one set of pins but internally several GPIO silicon blocks, each modeled as
+a struct gpio_chip) any number of GPIO ranges can be added to a pin controller
+instance like this:
+
+struct gpio_chip chip_a;
+struct gpio_chip chip_b;
+
+static struct pinctrl_gpio_range gpio_range_a = {
+	.name = "chip a",
+	.id = 0,
+	.base = 32,
+	.npins = 16,
+	.gc = &chip_a;
+};
+
+static struct pinctrl_gpio_range gpio_range_a = {
+	.name = "chip b",
+	.id = 0,
+	.base = 48,
+	.npins = 8,
+	.gc = &chip_b;
+};
+
+
+{
+	struct pinctrl_dev *pctl;
+	...
+	pinctrl_add_gpio_range(pctl, &gpio_range_a);
+	pinctrl_add_gpio_range(pctl, &gpio_range_b);
+}
+
+So this complex system has one pin controller handling two different
+GPIO chips. Chip a has 16 pins and chip b has 8 pins. They are mapped in
+the global GPIO pin space at:
+
+chip a: [32 .. 47]
+chip b: [48 .. 55]
+
+When GPIO-specific functions in the pin control subsystem are called, these
+ranges will be used to look up the apropriate pin controller by inspecting
+and matching the pin to the pin ranges across all controllers. When a
+pin controller handling the matching range is found, GPIO-specific functions
+will be called on that specific pin controller.
+
+For all functionalities dealing with pin biasing, pin muxing etc, the pin
+controller subsystem will subtract the range's .base offset from the passed
+in gpio pin number, and pass that on to the pin control driver, so the driver
+will get an offset into its handled number range. Further it is also passed
+the range ID value, so that the pin controller knows which range it should
+deal with.
+
+For example: if a user issues pinctrl_gpio_set_foo(50), the pin control
+subsystem will find that the second range on this pin controller matches,
+subtract the base 48 and call the
+pinctrl_driver_gpio_set_foo(pinctrl, range, 2) where the latter function has
+this signature:
+
+int pinctrl_driver_gpio_set_foo(struct pinctrl_dev *pctldev,
+    struct pinctrl_gpio_range *rangeid,
+    unsigned offset);
+
+Now the driver knows that we want to do some GPIO-specific operation on the
+second GPIO range handled by "chip b", at offset 2 in that specific range.
+
+(If the GPIO subsystem is ever refactored to use a local per-GPIO controller
+pin space, this mapping will need to be augmented accordingly.)
+
+
+PINMUX interfaces
+=================
+
+These calls use the pinmux_* naming prefix.  No other calls should use that
+prefix.
+
+
+What is pinmuxing?
+==================
+
+PINMUX, also known as padmux, ballmux, alternate functions or mission modes
+is a way for chip vendors producing some kind of electrical packages to use
+a certain physical pin (ball, pad, finger, etc) for multiple mutually exclusive
+functions, depending on the application. By "application" in this context
+we usually mean a way of soldering or wiring the package into an electronic
+system, even though the framework makes it possible to also change the function
+at runtime.
+
+Here is an example of a PGA (Pin Grid Array) chip seen from underneath:
+
+        A   B   C   D   E   F   G   H
+      +---+
+   8  | o | o   o   o   o   o   o   o
+      |   |
+   7  | o | o   o   o   o   o   o   o
+      |   |
+   6  | o | o   o   o   o   o   o   o
+      +---+---+
+   5  | o | o | o   o   o   o   o   o
+      +---+---+               +---+
+   4    o   o   o   o   o   o | o | o
+                              |   |
+   3    o   o   o   o   o   o | o | o
+                              |   |
+   2    o   o   o   o   o   o | o | o
+      +-------+-------+-------+---+---+
+   1  | o   o | o   o | o   o | o | o |
+      +-------+-------+-------+---+---+
+
+This is not tetris. The game to think of is chess. Not all PGA/BGA packages
+are chessboard-like, big ones have "holes" in some arrangement according to
+different design patterns, but we're using this as a simple example. Of the
+pins you see some will be taken by things like a few VCC and GND to feed power
+to the chip, and quite a few will be taken by large ports like an external
+memory interface. The remaining pins will often be subject to pin multiplexing.
+
+The example 8x8 PGA package above will have pin numbers 0 thru 63 assigned to
+its physical pins. It will name the pins { A1, A2, A3 ... H6, H7, H8 } using
+pinctrl_register_pins() and a suitable data set as shown earlier.
+
+In this 8x8 BGA package the pins { A8, A7, A6, A5 } can be used as an SPI port
+(these are four pins: CLK, RXD, TXD, FRM). In that case, pin B5 can be used as
+some general-purpose GPIO pin. However, in another setting, pins { A5, B5 } can
+be used as an I2C port (these are just two pins: SCL, SDA). Needless to say,
+we cannot use the SPI port and I2C port at the same time. However in the inside
+of the package the silicon performing the SPI logic can alternatively be routed
+out on pins { G4, G3, G2, G1 }.
+
+On the botton row at { A1, B1, C1, D1, E1, F1, G1, H1 } we have something
+special - it's an external MMC bus that can be 2, 4 or 8 bits wide, and it will
+consume 2, 4 or 8 pins respectively, so either { A1, B1 } are taken or
+{ A1, B1, C1, D1 } or all of them. If we use all 8 bits, we cannot use the SPI
+port on pins { G4, G3, G2, G1 } of course.
+
+This way the silicon blocks present inside the chip can be multiplexed "muxed"
+out on different pin ranges. Often contemporary SoC (systems on chip) will
+contain several I2C, SPI, SDIO/MMC, etc silicon blocks that can be routed to
+different pins by pinmux settings.
+
+Since general-purpose I/O pins (GPIO) are typically always in shortage, it is
+common to be able to use almost any pin as a GPIO pin if it is not currently
+in use by some other I/O port.
+
+
+Pinmux conventions
+==================
+
+The purpose of the pinmux functionality in the pin controller subsystem is to
+abstract and provide pinmux settings to the devices you choose to instantiate
+in your machine configuration. It is inspired by the clk, GPIO and regulator
+subsystems, so devices will request their mux setting, but it's also possible
+to request a single pin for e.g. GPIO.
+
+Definitions:
+
+- FUNCTIONS can be switched in and out by a driver residing with the pin
+  control subsystem in the drivers/pinctrl/* directory of the kernel. The
+  pin control driver knows the possible functions. In the example above you can
+  identify three pinmux functions, one for spi, one for i2c and one for mmc.
+
+- FUNCTIONS are assumed to be enumerable from zero in a one-dimensional array.
+  In this case the array could be something like: { spi0, i2c0, mmc0 }
+  for the three available functions.
+
+- FUNCTIONS have PIN GROUPS as defined on the generic level - so a certain
+  function is *always* associated with a certain set of pin groups, could
+  be just a single one, but could also be many. In the example above the
+  function i2c is associated with the pins { A5, B5 }, enumerated as
+  { 24, 25 } in the controller pin space.
+
+  The Function spi is associated with pin groups { A8, A7, A6, A5 }
+  and { G4, G3, G2, G1 }, which are enumerated as { 0, 8, 16, 24 } and
+  { 38, 46, 54, 62 } respectively.
+
+  Group names must be unique per pin controller, no two groups on the same
+  controller may have the same name.
+
+- The combination of a FUNCTION and a PIN GROUP determine a certain function
+  for a certain set of pins. The knowledge of the functions and pin groups
+  and their machine-specific particulars are kept inside the pinmux driver,
+  from the outside only the enumerators are known, and the driver core can:
+
+  - Request the name of a function with a certain selector (>= 0)
+  - A list of groups associated with a certain function
+  - Request that a certain group in that list to be activated for a certain
+    function
+
+  As already described above, pin groups are in turn self-descriptive, so
+  the core will retrieve the actual pin range in a certain group from the
+  driver.
+
+- FUNCTIONS and GROUPS on a certain PIN CONTROLLER are MAPPED to a certain
+  device by the board file, device tree or similar machine setup configuration
+  mechanism, similar to how regulators are connected to devices, usually by
+  name. Defining a pin controller, function and group thus uniquely identify
+  the set of pins to be used by a certain device. (If only one possible group
+  of pins is available for the function, no group name need to be supplied -
+  the core will simply select the first and only group available.)
+
+  In the example case we can define that this particular machine shall
+  use device spi0 with pinmux function fspi0 group gspi0 and i2c0 on function
+  fi2c0 group gi2c0, on the primary pin controller, we get mappings
+  like these:
+
+  {
+    {"map-spi0", spi0, pinctrl0, fspi0, gspi0},
+    {"map-i2c0", i2c0, pinctrl0, fi2c0, gi2c0}
+  }
+
+  Every map must be assigned a symbolic name, pin controller and function.
+  The group is not compulsory - if it is omitted the first group presented by
+  the driver as applicable for the function will be selected, which is
+  useful for simple cases.
+
+  The device name is present in map entries tied to specific devices. Maps
+  without device names are referred to as SYSTEM pinmuxes, such as can be taken
+  by the machine implementation on boot and not tied to any specific device.
+
+  It is possible to map several groups to the same combination of device,
+  pin controller and function. This is for cases where a certain function on
+  a certain pin controller may use different sets of pins in different
+  configurations.
+
+- PINS for a certain FUNCTION using a certain PIN GROUP on a certain
+  PIN CONTROLLER are provided on a first-come first-serve basis, so if some
+  other device mux setting or GPIO pin request has already taken your physical
+  pin, you will be denied the use of it. To get (activate) a new setting, the
+  old one has to be put (deactivated) first.
+
+Sometimes the documentation and hardware registers will be oriented around
+pads (or "fingers") rather than pins - these are the soldering surfaces on the
+silicon inside the package, and may or may not match the actual number of
+pins/balls underneath the capsule. Pick some enumeration that makes sense to
+you. Define enumerators only for the pins you can control if that makes sense.
+
+Assumptions:
+
+We assume that the number possible function maps to pin groups is limited by
+the hardware. I.e. we assume that there is no system where any function can be
+mapped to any pin, like in a phone exchange. So the available pins groups for
+a certain function will be limited to a few choices (say up to eight or so),
+not hundreds or any amount of choices. This is the characteristic we have found
+by inspecting available pinmux hardware, and a necessary assumption since we
+expect pinmux drivers to present *all* possible function vs pin group mappings
+to the subsystem.
+
+
+Pinmux drivers
+==============
+
+The pinmux core takes care of preventing conflicts on pins and calling
+the pin controller driver to execute different settings.
+
+It is the responsibility of the pinmux driver to impose further restrictions
+(say for example infer electronic limitations due to load etc) to determine
+whether or not the requested function can actually be allowed, and in case it
+is possible to perform the requested mux setting, poke the hardware so that
+this happens.
+
+Pinmux drivers are required to supply a few callback functions, some are
+optional. Usually the enable() and disable() functions are implemented,
+writing values into some certain registers to activate a certain mux setting
+for a certain pin.
+
+A simple driver for the above example will work by setting bits 0, 1, 2, 3 or 4
+into some register named MUX to select a certain function with a certain
+group of pins would work something like this:
+
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+struct foo_group {
+	const char *name;
+	const unsigned int *pins;
+	const unsigned num_pins;
+};
+
+static const unsigned spi0_0_pins[] = { 0, 8, 16, 24 };
+static const unsigned spi0_1_pins[] = { 38, 46, 54, 62 };
+static const unsigned i2c0_pins[] = { 24, 25 };
+static const unsigned mmc0_1_pins[] = { 56, 57 };
+static const unsigned mmc0_2_pins[] = { 58, 59 };
+static const unsigned mmc0_3_pins[] = { 60, 61, 62, 63 };
+
+static const struct foo_group foo_groups[] = {
+	{
+		.name = "spi0_0_grp",
+		.pins = spi0_0_pins,
+		.num_pins = ARRAY_SIZE(spi0_0_pins),
+	},
+	{
+		.name = "spi0_1_grp",
+		.pins = spi0_1_pins,
+		.num_pins = ARRAY_SIZE(spi0_1_pins),
+	},
+	{
+		.name = "i2c0_grp",
+		.pins = i2c0_pins,
+		.num_pins = ARRAY_SIZE(i2c0_pins),
+	},
+	{
+		.name = "mmc0_1_grp",
+		.pins = mmc0_1_pins,
+		.num_pins = ARRAY_SIZE(mmc0_1_pins),
+	},
+	{
+		.name = "mmc0_2_grp",
+		.pins = mmc0_2_pins,
+		.num_pins = ARRAY_SIZE(mmc0_2_pins),
+	},
+	{
+		.name = "mmc0_3_grp",
+		.pins = mmc0_3_pins,
+		.num_pins = ARRAY_SIZE(mmc0_3_pins),
+	},
+};
+
+
+static int foo_list_groups(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(foo_groups))
+		return -EINVAL;
+	return 0;
+}
+
+static const char *foo_get_group_name(struct pinctrl_dev *pctldev,
+				       unsigned selector)
+{
+	return foo_groups[selector].name;
+}
+
+static int foo_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
+			       unsigned ** const pins,
+			       unsigned * const num_pins)
+{
+	*pins = (unsigned *) foo_groups[selector].pins;
+	*num_pins = foo_groups[selector].num_pins;
+	return 0;
+}
+
+static struct pinctrl_ops foo_pctrl_ops = {
+	.list_groups = foo_list_groups,
+	.get_group_name = foo_get_group_name,
+	.get_group_pins = foo_get_group_pins,
+};
+
+struct foo_pmx_func {
+	const char *name;
+	const char * const *groups;
+	const unsigned num_groups;
+};
+
+static const char * const spi0_groups[] = { "spi0_1_grp" };
+static const char * const i2c0_groups[] = { "i2c0_grp" };
+static const char * const mmc0_groups[] = { "mmc0_1_grp", "mmc0_2_grp",
+					"mmc0_3_grp" };
+
+static const struct foo_pmx_func foo_functions[] = {
+	{
+		.name = "spi0",
+		.groups = spi0_groups,
+		.num_groups = ARRAY_SIZE(spi0_groups),
+	},
+	{
+		.name = "i2c0",
+		.groups = i2c0_groups,
+		.num_groups = ARRAY_SIZE(i2c0_groups),
+	},
+	{
+		.name = "mmc0",
+		.groups = mmc0_groups,
+		.num_groups = ARRAY_SIZE(mmc0_groups),
+	},
+};
+
+int foo_list_funcs(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(foo_functions))
+		return -EINVAL;
+	return 0;
+}
+
+const char *foo_get_fname(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	return myfuncs[selector].name;
+}
+
+static int foo_get_groups(struct pinctrl_dev *pctldev, unsigned selector,
+			  const char * const **groups,
+			  unsigned * const num_groups)
+{
+	*groups = foo_functions[selector].groups;
+	*num_groups = foo_functions[selector].num_groups;
+	return 0;
+}
+
+int foo_enable(struct pinctrl_dev *pctldev, unsigned selector,
+		unsigned group)
+{
+	u8 regbit = (1 << group);
+
+	writeb((readb(MUX)|regbit), MUX)
+	return 0;
+}
+
+int foo_disable(struct pinctrl_dev *pctldev, unsigned selector,
+		unsigned group)
+{
+	u8 regbit = (1 << group);
+
+	writeb((readb(MUX) & ~(regbit)), MUX)
+	return 0;
+}
+
+struct pinmux_ops foo_pmxops = {
+	.list_functions = foo_list_funcs,
+	.get_function_name = foo_get_fname,
+	.get_function_groups = foo_get_groups,
+	.enable = foo_enable,
+	.disable = foo_disable,
+};
+
+/* Pinmux operations are handled by some pin controller */
+static struct pinctrl_desc foo_desc = {
+	...
+	.pctlops = &foo_pctrl_ops,
+	.pmxops = &foo_pmxops,
+};
+
+In the example activating muxing 0 and 1 at the same time setting bits
+0 and 1, uses one pin in common so they would collide.
+
+The beauty of the pinmux subsystem is that since it keeps track of all
+pins and who is using them, it will already have denied an impossible
+request like that, so the driver does not need to worry about such
+things - when it gets a selector passed in, the pinmux subsystem makes
+sure no other device or GPIO assignment is already using the selected
+pins. Thus bits 0 and 1 in the control register will never be set at the
+same time.
+
+All the above functions are mandatory to implement for a pinmux driver.
+
+
+Pinmux interaction with the GPIO subsystem
+==========================================
+
+The function list could become long, especially if you can convert every
+individual pin into a GPIO pin independent of any other pins, and then try
+the approach to define every pin as a function.
+
+In this case, the function array would become 64 entries for each GPIO
+setting and then the device functions.
+
+For this reason there is an additional function a pinmux driver can implement
+to enable only GPIO on an individual pin: .gpio_request_enable(). The same
+.free() function as for other functions is assumed to be usable also for
+GPIO pins.
+
+This function will pass in the affected GPIO range identified by the pin
+controller core, so you know which GPIO pins are being affected by the request
+operation.
+
+Alternatively it is fully allowed to use named functions for each GPIO
+pin, the pinmux_request_gpio() will attempt to obtain the function "gpioN"
+where "N" is the global GPIO pin number if no special GPIO-handler is
+registered.
+
+
+Pinmux board/machine configuration
+==================================
+
+Boards and machines define how a certain complete running system is put
+together, including how GPIOs and devices are muxed, how regulators are
+constrained and how the clock tree looks. Of course pinmux settings are also
+part of this.
+
+A pinmux config for a machine looks pretty much like a simple regulator
+configuration, so for the example array above we want to enable i2c and
+spi on the second function mapping:
+
+#include <linux/pinctrl/machine.h>
+
+static struct pinmux_map pmx_mapping[] = {
+	{
+		.ctrl_dev_name = "pinctrl.0",
+		.function = "spi0",
+		.dev_name = "foo-spi.0",
+	},
+	{
+		.ctrl_dev_name = "pinctrl.0",
+		.function = "i2c0",
+		.dev_name = "foo-i2c.0",
+	},
+	{
+		.ctrl_dev_name = "pinctrl.0",
+		.function = "mmc0",
+		.dev_name = "foo-mmc.0",
+	},
+};
+
+The dev_name here matches to the unique device name that can be used to look
+up the device struct (just like with clockdev or regulators). The function name
+must match a function provided by the pinmux driver handling this pin range.
+
+As you can see we may have several pin controllers on the system and thus
+we need to specify which one of them that contain the functions we wish
+to map. The map can also use struct device * directly, so there is no
+inherent need to use strings to specify .dev_name or .ctrl_dev_name, these
+are for the situation where you do not have a handle to the struct device *,
+for example if they are not yet instantiated or cumbersome to obtain.
+
+You register this pinmux mapping to the pinmux subsystem by simply:
+
+       ret = pinmux_register_mappings(&pmx_mapping, ARRAY_SIZE(pmx_mapping));
+
+Since the above construct is pretty common there is a helper macro to make
+it even more compact which assumes you want to use pinctrl.0 and position
+0 for mapping, for example:
+
+static struct pinmux_map pmx_mapping[] = {
+       PINMUX_MAP_PRIMARY("I2CMAP", "i2c0", "foo-i2c.0"),
+};
+
+
+Complex mappings
+================
+
+As it is possible to map a function to different groups of pins an optional
+.group can be specified like this:
+
+...
+{
+	.name = "spi0-pos-A",
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "spi0",
+	.group = "spi0_0_grp",
+	.dev_name = "foo-spi.0",
+},
+{
+	.name = "spi0-pos-B",
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "spi0",
+	.group = "spi0_1_grp",
+	.dev_name = "foo-spi.0",
+},
+...
+
+This example mapping is used to switch between two positions for spi0 at
+runtime, as described further below under the heading "Runtime pinmuxing".
+
+Further it is possible to match several groups of pins to the same function
+for a single device, say for example in the mmc0 example above, where you can
+additively expand the mmc0 bus from 2 to 4 to 8 pins. If we want to use all
+three groups for a total of 2+2+4 = 8 pins (for an 8-bit MMC bus as is the
+case), we define a mapping like this:
+
+...
+{
+	.name "2bit"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "mmc0",
+	.group = "mmc0_0_grp",
+	.dev_name = "foo-mmc.0",
+},
+{
+	.name "4bit"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "mmc0",
+	.group = "mmc0_0_grp",
+	.dev_name = "foo-mmc.0",
+},
+{
+	.name "4bit"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "mmc0",
+	.group = "mmc0_1_grp",
+	.dev_name = "foo-mmc.0",
+},
+{
+	.name "8bit"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "mmc0",
+	.group = "mmc0_0_grp",
+	.dev_name = "foo-mmc.0",
+},
+{
+	.name "8bit"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "mmc0",
+	.group = "mmc0_1_grp",
+	.dev_name = "foo-mmc.0",
+},
+{
+	.name "8bit"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "mmc0",
+	.group = "mmc0_2_grp",
+	.dev_name = "foo-mmc.0",
+},
+...
+
+The result of grabbing this mapping from the device with something like
+this (see next paragraph):
+
+	pmx = pinmux_get(&device, "8bit");
+
+Will be that you activate all the three bottom records in the mapping at
+once. Since they share the same name, pin controller device, funcion and
+device, and since we allow multiple groups to match to a single device, they
+all get selected, and they all get enabled and disable simultaneously by the
+pinmux core.
+
+
+Pinmux requests from drivers
+============================
+
+Generally it is discouraged to let individual drivers get and enable pinmuxes.
+So if possible, handle the pinmuxes in platform code or some other place where
+you have access to all the affected struct device * pointers. In some cases
+where a driver needs to switch between different mux mappings at runtime
+this is not possible.
+
+A driver may request a certain mux to be activated, usually just the default
+mux like this:
+
+#include <linux/pinctrl/pinmux.h>
+
+struct foo_state {
+       struct pinmux *pmx;
+       ...
+};
+
+foo_probe()
+{
+	/* Allocate a state holder named "state" etc */
+	struct pinmux pmx;
+
+	pmx = pinmux_get(&device, NULL);
+	if IS_ERR(pmx)
+		return PTR_ERR(pmx);
+	pinmux_enable(pmx);
+
+	state->pmx = pmx;
+}
+
+foo_remove()
+{
+	pinmux_disable(state->pmx);
+	pinmux_put(state->pmx);
+}
+
+If you want to grab a specific mux mapping and not just the first one found for
+this device you can specify a specific mapping name, for example in the above
+example the second i2c0 setting: pinmux_get(&device, "spi0-pos-B");
+
+This get/enable/disable/put sequence can just as well be handled by bus drivers
+if you don't want each and every driver to handle it and you know the
+arrangement on your bus.
+
+The semantics of the get/enable respective disable/put is as follows:
+
+- pinmux_get() is called in process context to reserve the pins affected with
+  a certain mapping and set up the pinmux core and the driver. It will allocate
+  a struct from the kernel memory to hold the pinmux state.
+
+- pinmux_enable()/pinmux_disable() is quick and can be called from fastpath
+  (irq context) when you quickly want to set up/tear down the hardware muxing
+  when running a device driver. Usually it will just poke some values into a
+  register.
+
+- pinmux_disable() is called in process context to tear down the pin requests
+  and release the state holder struct for the mux setting.
+
+Usually the pinmux core handled the get/put pair and call out to the device
+drivers bookkeeping operations, like checking available functions and the
+associated pins, whereas the enable/disable pass on to the pin controller
+driver which takes care of activating and/or deactivating the mux setting by
+quickly poking some registers.
+
+The pins are allocated for your device when you issue the pinmux_get() call,
+after this you should be able to see this in the debugfs listing of all pins.
+
+
+System pinmux hogging
+=====================
+
+A system pinmux map entry, i.e. a pinmux setting that does not have a device
+associated with it, can be hogged by the core when the pin controller is
+registered. This means that the core will attempt to call pinmux_get() and
+pinmux_enable() on it immediately after the pin control device has been
+registered.
+
+This is enabled by simply setting the .hog_on_boot field in the map to true,
+like this:
+
+{
+	.name "POWERMAP"
+	.ctrl_dev_name = "pinctrl.0",
+	.function = "power_func",
+	.hog_on_boot = true,
+},
+
+Since it may be common to request the core to hog a few always-applicable
+mux settings on the primary pin controller, there is a convenience macro for
+this:
+
+PINMUX_MAP_PRIMARY_SYS_HOG("POWERMAP", "power_func")
+
+This gives the exact same result as the above construction.
+
+
+Runtime pinmuxing
+=================
+
+It is possible to mux a certain function in and out at runtime, say to move
+an SPI port from one set of pins to another set of pins. Say for example for
+spi0 in the example above, we expose two different groups of pins for the same
+function, but with different named in the mapping as described under
+"Advanced mapping" above. So we have two mappings named "spi0-pos-A" and
+"spi0-pos-B".
+
+This snippet first muxes the function in the pins defined by group A, enables
+it, disables and releases it, and muxes it in on the pins defined by group B:
+
+foo_switch()
+{
+	struct pinmux pmx;
+
+	/* Enable on position A */
+	pmx = pinmux_get(&device, "spi0-pos-A");
+	if IS_ERR(pmx)
+		return PTR_ERR(pmx);
+	pinmux_enable(pmx);
+
+	/* This releases the pins again */
+	pinmux_disable(pmx);
+	pinmux_put(pmx);
+
+	/* Enable on position B */
+	pmx = pinmux_get(&device, "spi0-pos-B");
+	if IS_ERR(pmx)
+		return PTR_ERR(pmx);
+	pinmux_enable(pmx);
+	...
+}
+
+The above has to be done from process context.
diff --git a/MAINTAINERS b/MAINTAINERS
index f1db840686b15f..04c0dd8d9921ce 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5042,6 +5042,11 @@ L:	linux-mtd@lists.infradead.org
 S:	Maintained
 F:	drivers/mtd/devices/phram.c
 
+PIN CONTROL SUBSYSTEM
+M:	Linus Walleij <linus.walleij@linaro.org>
+S:	Maintained
+F:	drivers/pinmux/
+
 PKTCDVD DRIVER
 M:	Peter Osterlund <petero2@telia.com>
 S:	Maintained
diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig
index 32a7b0f7e9f79b..449fd6a8dbd668 100644
--- a/arch/arm/mach-u300/Kconfig
+++ b/arch/arm/mach-u300/Kconfig
@@ -6,6 +6,8 @@ comment "ST-Ericsson Mobile Platform Products"
 
 config MACH_U300
 	bool "U300"
+	select PINCTRL
+	select PINMUX_U300
 
 comment "ST-Ericsson U300/U330/U335/U365 Feature Selections"
 
diff --git a/arch/arm/mach-u300/Makefile b/arch/arm/mach-u300/Makefile
index 8fd354aaf0a7f5..285538124e5e7d 100644
--- a/arch/arm/mach-u300/Makefile
+++ b/arch/arm/mach-u300/Makefile
@@ -2,7 +2,7 @@
 # Makefile for the linux kernel, U300 machine.
 #
 
-obj-y		:= core.o clock.o timer.o padmux.o
+obj-y		:= core.o clock.o timer.o
 obj-m		:=
 obj-n		:=
 obj-		:=
diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c
index 399c89f14dfb5b..2f5929bdeaa203 100644
--- a/arch/arm/mach-u300/core.c
+++ b/arch/arm/mach-u300/core.c
@@ -25,6 +25,8 @@
 #include <linux/err.h>
 #include <linux/mtd/nand.h>
 #include <linux/mtd/fsmc.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinmux.h>
 
 #include <asm/types.h>
 #include <asm/setup.h>
@@ -1535,6 +1537,14 @@ static struct coh901318_platform coh901318_platform = {
 	.max_channels = U300_DMA_CHANNELS,
 };
 
+static struct resource pinmux_resources[] = {
+	{
+		.start = U300_SYSCON_BASE,
+		.end   = U300_SYSCON_BASE + SZ_4K - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
 static struct platform_device wdog_device = {
 	.name = "coh901327_wdog",
 	.id = -1,
@@ -1630,6 +1640,72 @@ static struct platform_device dma_device = {
 	},
 };
 
+static struct platform_device pinmux_device = {
+	.name = "pinmux-u300",
+	.id = -1,
+	.num_resources = ARRAY_SIZE(pinmux_resources),
+	.resource = pinmux_resources,
+};
+
+/* Pinmux settings */
+static struct pinmux_map u300_pinmux_map[] = {
+	/* anonymous maps for chip power and EMIFs */
+	PINMUX_MAP_PRIMARY_SYS_HOG("POWER", "power"),
+	PINMUX_MAP_PRIMARY_SYS_HOG("EMIF0", "emif0"),
+	PINMUX_MAP_PRIMARY_SYS_HOG("EMIF1", "emif1"),
+	/* per-device maps for MMC/SD, SPI and UART */
+	PINMUX_MAP_PRIMARY("MMCSD", "mmc0", "mmci"),
+	PINMUX_MAP_PRIMARY("SPI", "spi0", "pl022"),
+	PINMUX_MAP_PRIMARY("UART0", "uart0", "uart0"),
+};
+
+struct u300_mux_hog {
+	const char *name;
+	struct device *dev;
+	struct pinmux *pmx;
+};
+
+static struct u300_mux_hog u300_mux_hogs[] = {
+	{
+		.name = "uart0",
+		.dev = &uart0_device.dev,
+	},
+	{
+		.name = "spi0",
+		.dev = &pl022_device.dev,
+	},
+	{
+		.name = "mmc0",
+		.dev = &mmcsd_device.dev,
+	},
+};
+
+static int __init u300_pinmux_fetch(void)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(u300_mux_hogs); i++) {
+		struct pinmux *pmx;
+		int ret;
+
+		pmx = pinmux_get(u300_mux_hogs[i].dev, NULL);
+		if (IS_ERR(pmx)) {
+			pr_err("u300: could not get pinmux hog %s\n",
+			       u300_mux_hogs[i].name);
+			continue;
+		}
+		ret = pinmux_enable(pmx);
+		if (ret) {
+			pr_err("u300: could enable pinmux hog %s\n",
+			       u300_mux_hogs[i].name);
+			continue;
+		}
+		u300_mux_hogs[i].pmx = pmx;
+	}
+	return 0;
+}
+subsys_initcall(u300_pinmux_fetch);
+
 /*
  * Notice that AMBA devices are initialized before platform devices.
  *
@@ -1643,10 +1719,10 @@ static struct platform_device *platform_devs[] __initdata = {
 	&gpio_device,
 	&nand_device,
 	&wdog_device,
-	&ave_device
+	&ave_device,
+	&pinmux_device,
 };
 
-
 /*
  * Interrupts: the U300 platforms have two pl190 ARM PrimeCells connected
  * together so some interrupts are connected to the first one and some
@@ -1828,6 +1904,10 @@ void __init u300_init_devices(void)
 
 	u300_assign_physmem();
 
+	/* Initialize pinmuxing */
+	pinmux_register_mappings(u300_pinmux_map,
+				 ARRAY_SIZE(u300_pinmux_map));
+
 	/* Register subdevices on the I2C buses */
 	u300_i2c_register_board_devices();
 
diff --git a/arch/arm/mach-u300/include/mach/syscon.h b/arch/arm/mach-u300/include/mach/syscon.h
index 7444f5c7da97fa..6e84f07a7c6f37 100644
--- a/arch/arm/mach-u300/include/mach/syscon.h
+++ b/arch/arm/mach-u300/include/mach/syscon.h
@@ -234,91 +234,6 @@
 #define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE	(0x0004)
 #define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE		(0x0002)
 #define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE		(0x0001)
-/* PAD MUX Control register 1 (LOW) 16bit (R/W) */
-#define U300_SYSCON_PMC1LR					(0x007C)
-#define U300_SYSCON_PMC1LR_MASK					(0xFFFF)
-#define U300_SYSCON_PMC1LR_CDI_MASK				(0xC000)
-#define U300_SYSCON_PMC1LR_CDI_CDI				(0x0000)
-#define U300_SYSCON_PMC1LR_CDI_EMIF				(0x4000)
-#ifdef CONFIG_MACH_U300_BS335
-#define U300_SYSCON_PMC1LR_CDI_CDI2				(0x8000)
-#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO			(0xC000)
-#elif CONFIG_MACH_U300_BS365
-#define U300_SYSCON_PMC1LR_CDI_GPIO				(0x8000)
-#define U300_SYSCON_PMC1LR_CDI_WCDMA				(0xC000)
-#endif
-#define U300_SYSCON_PMC1LR_PDI_MASK				(0x3000)
-#define U300_SYSCON_PMC1LR_PDI_PDI				(0x0000)
-#define U300_SYSCON_PMC1LR_PDI_EGG				(0x1000)
-#define U300_SYSCON_PMC1LR_PDI_WCDMA				(0x3000)
-#define U300_SYSCON_PMC1LR_MMCSD_MASK				(0x0C00)
-#define U300_SYSCON_PMC1LR_MMCSD_MMCSD				(0x0000)
-#define U300_SYSCON_PMC1LR_MMCSD_MSPRO				(0x0400)
-#define U300_SYSCON_PMC1LR_MMCSD_DSP				(0x0800)
-#define U300_SYSCON_PMC1LR_MMCSD_WCDMA				(0x0C00)
-#define U300_SYSCON_PMC1LR_ETM_MASK				(0x0300)
-#define U300_SYSCON_PMC1LR_ETM_ACC				(0x0000)
-#define U300_SYSCON_PMC1LR_ETM_APP				(0x0100)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK			(0x00C0)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC			(0x0000)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF			(0x0040)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM			(0x0080)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB		(0x00C0)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK			(0x0030)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC			(0x0000)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF			(0x0010)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM			(0x0020)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI			(0x0030)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK			(0x000C)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC			(0x0000)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF			(0x0004)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM			(0x0008)
-#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI			(0x000C)
-#define U300_SYSCON_PMC1LR_EMIF_1_MASK				(0x0003)
-#define U300_SYSCON_PMC1LR_EMIF_1_STATIC			(0x0000)
-#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0			(0x0001)
-#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1			(0x0002)
-#define U300_SYSCON_PMC1LR_EMIF_1				(0x0003)
-/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */
-#define U300_SYSCON_PMC1HR					(0x007E)
-#define U300_SYSCON_PMC1HR_MASK					(0xFFFF)
-#define U300_SYSCON_PMC1HR_MISC_2_MASK				(0xC000)
-#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC1HR_MISC_2_MSPRO				(0x4000)
-#define U300_SYSCON_PMC1HR_MISC_2_DSP				(0x8000)
-#define U300_SYSCON_PMC1HR_MISC_2_AAIF				(0xC000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK			(0x3000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF			(0x1000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP			(0x2000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF			(0x3000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK			(0x0C00)
-#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC			(0x0400)
-#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP			(0x0800)
-#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF			(0x0C00)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK			(0x0300)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO		(0x0000)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI			(0x0100)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF			(0x0300)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK			(0x00C0)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO		(0x0000)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI			(0x0040)
-#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF			(0x00C0)
-#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK			(0x0030)
-#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI			(0x0010)
-#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP			(0x0020)
-#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF			(0x0030)
-#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK			(0x000C)
-#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0			(0x0004)
-#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS			(0x0008)
-#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF			(0x000C)
-#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK			(0x0003)
-#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0			(0x0001)
-#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF			(0x0003)
 /* Step one for killing the applications system 16bit (-/W) */
 #define U300_SYSCON_KA1R					(0x0080)
 #define U300_SYSCON_KA1R_MASK					(0xFFFF)
@@ -357,57 +272,6 @@
 #define U300_SYSCON_PUCR_EMIF_1_16BIT_PU_ENABLE			(0x0080)
 #define U300_SYSCON_PUCR_EMIF_1_8BIT_PU_ENABLE			(0x0040)
 #define U300_SYSCON_PUCR_KEY_IN_PU_EN_MASK			(0x003F)
-/* Padmux 2 control */
-#define U300_SYSCON_PMC2R					(0x100)
-#define U300_SYSCON_PMC2R_APP_MISC_0_MASK			(0x00C0)
-#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM			(0x0040)
-#define U300_SYSCON_PMC2R_APP_MISC_0_MMC			(0x0080)
-#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2			(0x00C0)
-#define U300_SYSCON_PMC2R_APP_MISC_1_MASK			(0x0300)
-#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM			(0x0100)
-#define U300_SYSCON_PMC2R_APP_MISC_1_MMC			(0x0200)
-#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2			(0x0300)
-#define U300_SYSCON_PMC2R_APP_MISC_2_MASK			(0x0C00)
-#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM			(0x0400)
-#define U300_SYSCON_PMC2R_APP_MISC_2_MMC			(0x0800)
-#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2			(0x0C00)
-#define U300_SYSCON_PMC2R_APP_MISC_3_MASK			(0x3000)
-#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM			(0x1000)
-#define U300_SYSCON_PMC2R_APP_MISC_3_MMC			(0x2000)
-#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2			(0x3000)
-#define U300_SYSCON_PMC2R_APP_MISC_4_MASK			(0xC000)
-#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM			(0x4000)
-#define U300_SYSCON_PMC2R_APP_MISC_4_MMC			(0x8000)
-#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO			(0xC000)
-/* TODO: More SYSCON registers missing */
-#define U300_SYSCON_PMC3R					(0x10c)
-#define U300_SYSCON_PMC3R_APP_MISC_11_MASK			(0xc000)
-#define U300_SYSCON_PMC3R_APP_MISC_11_SPI			(0x4000)
-#define U300_SYSCON_PMC3R_APP_MISC_10_MASK			(0x3000)
-#define U300_SYSCON_PMC3R_APP_MISC_10_SPI			(0x1000)
-/* TODO: Missing other configs */
-#define U300_SYSCON_PMC4R					(0x168)
-#define U300_SYSCON_PMC4R_APP_MISC_12_MASK			(0x0003)
-#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO			(0x0000)
-#define U300_SYSCON_PMC4R_APP_MISC_13_MASK			(0x000C)
-#define U300_SYSCON_PMC4R_APP_MISC_13_CDI			(0x0000)
-#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA			(0x0004)
-#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2			(0x0008)
-#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO			(0x000C)
-#define U300_SYSCON_PMC4R_APP_MISC_14_MASK			(0x0030)
-#define U300_SYSCON_PMC4R_APP_MISC_14_CDI			(0x0000)
-#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA			(0x0010)
-#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2			(0x0020)
-#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO			(0x0030)
-#define U300_SYSCON_PMC4R_APP_MISC_16_MASK			(0x0300)
-#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13		(0x0000)
-#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS		(0x0100)
-#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N	(0x0200)
 /* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
 #define U300_SYSCON_S0CCR					(0x120)
 #define U300_SYSCON_S0CCR_FIELD_MASK				(0x43FF)
diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c
index 677ccef5cd32ed..d5e4a98a9ab878 100644
--- a/arch/arm/mach-u300/mmc.c
+++ b/arch/arm/mach-u300/mmc.c
@@ -21,7 +21,6 @@
 #include <mach/dma_channels.h>
 
 #include "mmc.h"
-#include "padmux.h"
 
 static struct mmci_platform_data mmc0_plat_data = {
 	/*
@@ -45,24 +44,9 @@ static struct mmci_platform_data mmc0_plat_data = {
 int __devinit mmc_init(struct amba_device *adev)
 {
 	struct device *mmcsd_device = &adev->dev;
-	struct pmx *pmx;
 	int ret = 0;
 
 	mmcsd_device->platform_data = &mmc0_plat_data;
 
-	/*
-	 * Setup padmuxing for MMC. Since this must always be
-	 * compiled into the kernel, pmx is never released.
-	 */
-	pmx = pmx_get(mmcsd_device, U300_APP_PMX_MMC_SETTING);
-
-	if (IS_ERR(pmx))
-		pr_warning("Could not get padmux handle\n");
-	else {
-		ret = pmx_activate(mmcsd_device, pmx);
-		if (IS_ERR_VALUE(ret))
-			pr_warning("Could not activate padmuxing\n");
-	}
-
 	return ret;
 }
diff --git a/arch/arm/mach-u300/padmux.c b/arch/arm/mach-u300/padmux.c
deleted file mode 100644
index 4c93c6cefd372d..00000000000000
--- a/arch/arm/mach-u300/padmux.c
+++ /dev/null
@@ -1,367 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/padmux.c
- *
- *
- * Copyright (C) 2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * U300 PADMUX functions
- * Author: Martin Persson <martin.persson@stericsson.com>
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/device.h>
-#include <linux/err.h>
-#include <linux/errno.h>
-#include <linux/io.h>
-#include <linux/mutex.h>
-#include <linux/string.h>
-#include <linux/bug.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <mach/u300-regs.h>
-#include <mach/syscon.h>
-#include "padmux.h"
-
-static DEFINE_MUTEX(pmx_mutex);
-
-const u32 pmx_registers[] = {
-	(U300_SYSCON_VBASE + U300_SYSCON_PMC1LR),
-	(U300_SYSCON_VBASE + U300_SYSCON_PMC1HR),
-	(U300_SYSCON_VBASE + U300_SYSCON_PMC2R),
-	(U300_SYSCON_VBASE + U300_SYSCON_PMC3R),
-	(U300_SYSCON_VBASE + U300_SYSCON_PMC4R)
-};
-
-/* High level functionality */
-
-/* Lazy dog:
- * onmask = {
- *   {"PMC1LR" mask, "PMC1LR" value},
- *   {"PMC1HR" mask, "PMC1HR" value},
- *   {"PMC2R"  mask, "PMC2R"  value},
- *   {"PMC3R"  mask, "PMC3R"  value},
- *   {"PMC4R"  mask, "PMC4R"  value}
- * }
- */
-static struct pmx mmc_setting = {
-	.setting = U300_APP_PMX_MMC_SETTING,
-	.default_on = false,
-	.activated = false,
-	.name = "MMC",
-	.onmask = {
-		   {U300_SYSCON_PMC1LR_MMCSD_MASK,
-		    U300_SYSCON_PMC1LR_MMCSD_MMCSD},
-		   {0, 0},
-		   {0, 0},
-		   {0, 0},
-		   {U300_SYSCON_PMC4R_APP_MISC_12_MASK,
-		    U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO}
-		   },
-};
-
-static struct pmx spi_setting = {
-	.setting = U300_APP_PMX_SPI_SETTING,
-	.default_on = false,
-	.activated = false,
-	.name = "SPI",
-	.onmask = {{0, 0},
-		   {U300_SYSCON_PMC1HR_APP_SPI_2_MASK |
-		    U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK |
-		    U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK,
-		    U300_SYSCON_PMC1HR_APP_SPI_2_SPI |
-		    U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI |
-		    U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI},
-		   {0, 0},
-		   {0, 0},
-		   {0, 0}
-		   },
-};
-
-/* Available padmux settings */
-static struct pmx *pmx_settings[] = {
-	&mmc_setting,
-	&spi_setting,
-};
-
-static void update_registers(struct pmx *pmx, bool activate)
-{
-	u16 regval, val, mask;
-	int i;
-
-	for (i = 0; i < ARRAY_SIZE(pmx_registers); i++) {
-		if (activate)
-			val = pmx->onmask[i].val;
-		else
-			val = 0;
-
-		mask = pmx->onmask[i].mask;
-		if (mask != 0) {
-			regval = readw(pmx_registers[i]);
-			regval &= ~mask;
-			regval |= val;
-			writew(regval, pmx_registers[i]);
-		}
-	}
-}
-
-struct pmx *pmx_get(struct device *dev, enum pmx_settings setting)
-{
-	int i;
-	struct pmx *pmx = ERR_PTR(-ENOENT);
-
-	if (dev == NULL)
-		return ERR_PTR(-EINVAL);
-
-	mutex_lock(&pmx_mutex);
-	for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
-
-		if (setting == pmx_settings[i]->setting) {
-
-			if (pmx_settings[i]->dev != NULL) {
-				WARN(1, "padmux: required setting "
-				     "in use by another consumer\n");
-			} else {
-				pmx = pmx_settings[i];
-				pmx->dev = dev;
-				dev_dbg(dev, "padmux: setting nr %d is now "
-					"bound to %s and ready to use\n",
-					setting, dev_name(dev));
-				break;
-			}
-		}
-	}
-	mutex_unlock(&pmx_mutex);
-
-	return pmx;
-}
-EXPORT_SYMBOL(pmx_get);
-
-int pmx_put(struct device *dev, struct pmx *pmx)
-{
-	int i;
-	int ret = -ENOENT;
-
-	if (pmx == NULL || dev == NULL)
-		return -EINVAL;
-
-	mutex_lock(&pmx_mutex);
-	for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
-
-		if (pmx->setting == pmx_settings[i]->setting) {
-
-			if (dev != pmx->dev) {
-				WARN(1, "padmux: cannot release handle as "
-					"it is bound to another consumer\n");
-				ret = -EINVAL;
-				break;
-			} else {
-				pmx_settings[i]->dev = NULL;
-				ret = 0;
-				break;
-			}
-		}
-	}
-	mutex_unlock(&pmx_mutex);
-
-	return ret;
-}
-EXPORT_SYMBOL(pmx_put);
-
-int pmx_activate(struct device *dev, struct pmx *pmx)
-{
-	int i, j, ret;
-	ret = 0;
-
-	if (pmx == NULL || dev == NULL)
-		return -EINVAL;
-
-	mutex_lock(&pmx_mutex);
-
-	/* Make sure the required bits are not used */
-	for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
-
-		if (pmx_settings[i]->dev == NULL || pmx_settings[i] == pmx)
-			continue;
-
-		for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) {
-
-			if (pmx_settings[i]->onmask[j].mask & pmx->
-				onmask[j].mask) {
-				/* More than one entry on the same bits */
-				WARN(1, "padmux: cannot activate "
-					"setting. Bit conflict with "
-					"an active setting\n");
-
-				ret = -EUSERS;
-				goto exit;
-			}
-		}
-	}
-	update_registers(pmx, true);
-	pmx->activated = true;
-	dev_dbg(dev, "padmux: setting nr %d is activated\n",
-		pmx->setting);
-
-exit:
-	mutex_unlock(&pmx_mutex);
-	return ret;
-}
-EXPORT_SYMBOL(pmx_activate);
-
-int pmx_deactivate(struct device *dev, struct pmx *pmx)
-{
-	int i;
-	int ret = -ENOENT;
-
-	if (pmx == NULL || dev == NULL)
-		return -EINVAL;
-
-	mutex_lock(&pmx_mutex);
-	for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
-
-		if (pmx_settings[i]->dev == NULL)
-			continue;
-
-		if (pmx->setting == pmx_settings[i]->setting) {
-
-			if (dev != pmx->dev) {
-				WARN(1, "padmux: cannot deactivate "
-				     "pmx setting as it was activated "
-				     "by another consumer\n");
-
-				ret = -EBUSY;
-				continue;
-			} else {
-				update_registers(pmx, false);
-				pmx_settings[i]->dev = NULL;
-				pmx->activated = false;
-				ret = 0;
-				dev_dbg(dev, "padmux: setting nr %d is deactivated",
-					pmx->setting);
-				break;
-			}
-		}
-	}
-	mutex_unlock(&pmx_mutex);
-
-	return ret;
-}
-EXPORT_SYMBOL(pmx_deactivate);
-
-/*
- * For internal use only. If it is to be exported,
- * it should be reentrant. Notice that pmx_activate
- * (i.e. runtime settings) always override default settings.
- */
-static int pmx_set_default(void)
-{
-	/* Used to identify several entries on the same bits */
-	u16 modbits[ARRAY_SIZE(pmx_registers)];
-
-	int i, j;
-
-	memset(modbits, 0, ARRAY_SIZE(pmx_registers) * sizeof(u16));
-
-	for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
-
-		if (!pmx_settings[i]->default_on)
-			continue;
-
-		for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) {
-
-			/* Make sure there is only one entry on the same bits */
-			if (modbits[j] & pmx_settings[i]->onmask[j].mask) {
-				BUG();
-				return -EUSERS;
-			}
-			modbits[j] |= pmx_settings[i]->onmask[j].mask;
-		}
-		update_registers(pmx_settings[i], true);
-	}
-	return 0;
-}
-
-#if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG))
-static int pmx_show(struct seq_file *s, void *data)
-{
-	int i;
-	seq_printf(s, "-------------------------------------------------\n");
-	seq_printf(s, "SETTING     BOUND TO DEVICE               STATE\n");
-	seq_printf(s, "-------------------------------------------------\n");
-	mutex_lock(&pmx_mutex);
-	for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) {
-		/* Format pmx and device name nicely */
-		char cdp[33];
-		int chars;
-
-		chars = snprintf(&cdp[0], 17, "%s", pmx_settings[i]->name);
-		while (chars < 16) {
-			cdp[chars] = ' ';
-			chars++;
-		}
-		chars = snprintf(&cdp[16], 17, "%s", pmx_settings[i]->dev ?
-				dev_name(pmx_settings[i]->dev) : "N/A");
-		while (chars < 16) {
-			cdp[chars+16] = ' ';
-			chars++;
-		}
-		cdp[32] = '\0';
-
-		seq_printf(s,
-			"%s\t%s\n",
-			&cdp[0],
-			pmx_settings[i]->activated ?
-			"ACTIVATED" : "DEACTIVATED"
-			);
-
-	}
-	mutex_unlock(&pmx_mutex);
-	return 0;
-}
-
-static int pmx_open(struct inode *inode, struct file *file)
-{
-	return single_open(file, pmx_show, NULL);
-}
-
-static const struct file_operations pmx_operations = {
-	.owner		= THIS_MODULE,
-	.open		= pmx_open,
-	.read		= seq_read,
-	.llseek		= seq_lseek,
-	.release	= single_release,
-};
-
-static int __init init_pmx_read_debugfs(void)
-{
-	/* Expose a simple debugfs interface to view pmx settings */
-	(void) debugfs_create_file("padmux", S_IFREG | S_IRUGO,
-				   NULL, NULL,
-				   &pmx_operations);
-	return 0;
-}
-
-/*
- * This needs to come in after the core_initcall(),
- * because debugfs is not available until
- * the subsystems come up.
- */
-module_init(init_pmx_read_debugfs);
-#endif
-
-static int __init pmx_init(void)
-{
-	int ret;
-
-	ret = pmx_set_default();
-
-	if (IS_ERR_VALUE(ret))
-		pr_crit("padmux: default settings could not be set\n");
-
-	return 0;
-}
-
-/* Should be initialized before consumers */
-core_initcall(pmx_init);
diff --git a/arch/arm/mach-u300/padmux.h b/arch/arm/mach-u300/padmux.h
deleted file mode 100644
index 6e8b86064097ca..00000000000000
--- a/arch/arm/mach-u300/padmux.h
+++ /dev/null
@@ -1,39 +0,0 @@
-/*
- *
- * arch/arm/mach-u300/padmux.h
- *
- *
- * Copyright (C) 2009 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * U300 PADMUX API
- * Author: Martin Persson <martin.persson@stericsson.com>
- */
-
-#ifndef __MACH_U300_PADMUX_H
-#define __MACH_U300_PADMUX_H
-
-enum pmx_settings {
-	U300_APP_PMX_MMC_SETTING,
-	U300_APP_PMX_SPI_SETTING
-};
-
-struct pmx_onmask {
-	u16 mask;		/* Mask bits */
-	u16 val;		/* Value when active */
-};
-
-struct pmx {
-	struct device *dev;
-	enum pmx_settings setting;
-	char *name;
-	bool activated;
-	bool default_on;
-	struct pmx_onmask onmask[];
-};
-
-struct pmx *pmx_get(struct device *dev, enum pmx_settings setting);
-int pmx_put(struct device *dev, struct pmx *pmx);
-int pmx_activate(struct device *dev, struct pmx *pmx);
-int pmx_deactivate(struct device *dev, struct pmx *pmx);
-
-#endif
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index 7b597e2b19e2aa..a1affacfa59c45 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -14,8 +14,6 @@
 #include <mach/coh901318.h>
 #include <mach/dma_channels.h>
 
-#include "padmux.h"
-
 /*
  * The following is for the actual devices on the SSP/SPI bus
  */
@@ -95,25 +93,7 @@ static struct pl022_ssp_controller ssp_platform_data = {
 
 void __init u300_spi_init(struct amba_device *adev)
 {
-	struct pmx *pmx;
-
 	adev->dev.platform_data = &ssp_platform_data;
-	/*
-	 * Setup padmuxing for SPI. Since this must always be
-	 * compiled into the kernel, pmx is never released.
-	 */
-	pmx = pmx_get(&adev->dev, U300_APP_PMX_SPI_SETTING);
-
-	if (IS_ERR(pmx))
-		dev_warn(&adev->dev, "Could not get padmux handle\n");
-	else {
-		int ret;
-
-		ret = pmx_activate(&adev->dev, pmx);
-		if (IS_ERR_VALUE(ret))
-			dev_warn(&adev->dev, "Could not activate padmuxing\n");
-	}
-
 }
 
 void __init u300_spi_register_board_devices(void)
diff --git a/drivers/Kconfig b/drivers/Kconfig
index 95b9e7eefadc9b..e73aaaee0138d9 100644
--- a/drivers/Kconfig
+++ b/drivers/Kconfig
@@ -56,6 +56,8 @@ source "drivers/pps/Kconfig"
 
 source "drivers/ptp/Kconfig"
 
+source "drivers/pinctrl/Kconfig"
+
 source "drivers/gpio/Kconfig"
 
 source "drivers/w1/Kconfig"
diff --git a/drivers/Makefile b/drivers/Makefile
index 7fa433a7030c4e..e7afb3acbc678f 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -5,6 +5,8 @@
 # Rewritten to use lists instead of if-statements.
 #
 
+# GPIO must come after pinctrl as gpios may need to mux pins etc
+obj-y				+= pinctrl/
 obj-y				+= gpio/
 obj-$(CONFIG_PCI)		+= pci/
 obj-$(CONFIG_PARISC)		+= parisc/
diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
new file mode 100644
index 00000000000000..ef566443f94525
--- /dev/null
+++ b/drivers/pinctrl/Kconfig
@@ -0,0 +1,43 @@
+#
+# PINCTRL infrastructure and drivers
+#
+
+menuconfig PINCTRL
+	bool "PINCTRL Support"
+	depends on EXPERIMENTAL
+	help
+	  This enables the PINCTRL subsystem for controlling pins
+	  on chip packages, for example multiplexing pins on primarily
+	  PGA and BGA packages for systems on chip.
+
+	  If unsure, say N.
+
+if PINCTRL
+
+config PINMUX
+	bool "Support pinmux controllers"
+	help
+	  Say Y here if you want the pincontrol subsystem to handle pin
+	  multiplexing drivers.
+
+config DEBUG_PINCTRL
+	bool "Debug PINCTRL calls"
+	depends on DEBUG_KERNEL
+	help
+	  Say Y here to add some extra checks and diagnostics to PINCTRL calls.
+
+config PINMUX_SIRF
+	bool "CSR SiRFprimaII pinmux driver"
+	depends on ARCH_PRIMA2
+	select PINMUX
+	help
+	  Say Y here to enable the SiRFprimaII pinmux driver
+
+config PINMUX_U300
+	bool "U300 pinmux driver"
+	depends on ARCH_U300
+	select PINMUX
+	help
+	  Say Y here to enable the U300 pinmux driver
+
+endif
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
new file mode 100644
index 00000000000000..bdc548a6b7e9bd
--- /dev/null
+++ b/drivers/pinctrl/Makefile
@@ -0,0 +1,8 @@
+# generic pinmux support
+
+ccflags-$(CONFIG_DEBUG_PINMUX)	+= -DDEBUG
+
+obj-$(CONFIG_PINCTRL)		+= core.o
+obj-$(CONFIG_PINMUX)		+= pinmux.o
+obj-$(CONFIG_PINMUX_SIRF)	+= pinmux-sirf.o
+obj-$(CONFIG_PINMUX_U300)	+= pinmux-u300.o
diff --git a/drivers/pinctrl/core.c b/drivers/pinctrl/core.c
new file mode 100644
index 00000000000000..423522d87313b5
--- /dev/null
+++ b/drivers/pinctrl/core.c
@@ -0,0 +1,598 @@
+/*
+ * Core driver for the pin control subsystem
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ * Based on bits of regulator core, gpio core and clk core
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#define pr_fmt(fmt) "pinctrl core: " fmt
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/radix-tree.h>
+#include <linux/err.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/sysfs.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/machine.h>
+#include "core.h"
+#include "pinmux.h"
+
+/* Global list of pin control devices */
+static DEFINE_MUTEX(pinctrldev_list_mutex);
+static LIST_HEAD(pinctrldev_list);
+
+static void pinctrl_dev_release(struct device *dev)
+{
+	struct pinctrl_dev *pctldev = dev_get_drvdata(dev);
+	kfree(pctldev);
+}
+
+const char *pinctrl_dev_get_name(struct pinctrl_dev *pctldev)
+{
+	/* We're not allowed to register devices without name */
+	return pctldev->desc->name;
+}
+EXPORT_SYMBOL_GPL(pinctrl_dev_get_name);
+
+void *pinctrl_dev_get_drvdata(struct pinctrl_dev *pctldev)
+{
+	return pctldev->driver_data;
+}
+EXPORT_SYMBOL_GPL(pinctrl_dev_get_drvdata);
+
+/**
+ * get_pinctrl_dev_from_dev() - look up pin controller device
+ * @dev: a device pointer, this may be NULL but then devname needs to be
+ *	defined instead
+ * @devname: the name of a device instance, as returned by dev_name(), this
+ *	may be NULL but then dev needs to be defined instead
+ *
+ * Looks up a pin control device matching a certain device name or pure device
+ * pointer, the pure device pointer will take precedence.
+ */
+struct pinctrl_dev *get_pinctrl_dev_from_dev(struct device *dev,
+					     const char *devname)
+{
+	struct pinctrl_dev *pctldev = NULL;
+	bool found = false;
+
+	mutex_lock(&pinctrldev_list_mutex);
+	list_for_each_entry(pctldev, &pinctrldev_list, node) {
+		if (dev &&  &pctldev->dev == dev) {
+			/* Matched on device pointer */
+			found = true;
+			break;
+		}
+
+		if (devname &&
+		    !strcmp(dev_name(&pctldev->dev), devname)) {
+			/* Matched on device name */
+			found = true;
+			break;
+		}
+	}
+	mutex_unlock(&pinctrldev_list_mutex);
+
+	return found ? pctldev : NULL;
+}
+
+struct pin_desc *pin_desc_get(struct pinctrl_dev *pctldev, int pin)
+{
+	struct pin_desc *pindesc;
+	unsigned long flags;
+
+	spin_lock_irqsave(&pctldev->pin_desc_tree_lock, flags);
+	pindesc = radix_tree_lookup(&pctldev->pin_desc_tree, pin);
+	spin_unlock_irqrestore(&pctldev->pin_desc_tree_lock, flags);
+
+	return pindesc;
+}
+
+/**
+ * pin_is_valid() - check if pin exists on controller
+ * @pctldev: the pin control device to check the pin on
+ * @pin: pin to check, use the local pin controller index number
+ *
+ * This tells us whether a certain pin exist on a certain pin controller or
+ * not. Pin lists may be sparse, so some pins may not exist.
+ */
+bool pin_is_valid(struct pinctrl_dev *pctldev, int pin)
+{
+	struct pin_desc *pindesc;
+
+	if (pin < 0)
+		return false;
+
+	pindesc = pin_desc_get(pctldev, pin);
+	if (pindesc == NULL)
+		return false;
+
+	return true;
+}
+EXPORT_SYMBOL_GPL(pin_is_valid);
+
+/* Deletes a range of pin descriptors */
+static void pinctrl_free_pindescs(struct pinctrl_dev *pctldev,
+				  const struct pinctrl_pin_desc *pins,
+				  unsigned num_pins)
+{
+	int i;
+
+	spin_lock(&pctldev->pin_desc_tree_lock);
+	for (i = 0; i < num_pins; i++) {
+		struct pin_desc *pindesc;
+
+		pindesc = radix_tree_lookup(&pctldev->pin_desc_tree,
+					    pins[i].number);
+		if (pindesc != NULL) {
+			radix_tree_delete(&pctldev->pin_desc_tree,
+					  pins[i].number);
+		}
+		kfree(pindesc);
+	}
+	spin_unlock(&pctldev->pin_desc_tree_lock);
+}
+
+static int pinctrl_register_one_pin(struct pinctrl_dev *pctldev,
+				    unsigned number, const char *name)
+{
+	struct pin_desc *pindesc;
+
+	pindesc = pin_desc_get(pctldev, number);
+	if (pindesc != NULL) {
+		pr_err("pin %d already registered on %s\n", number,
+		       pctldev->desc->name);
+		return -EINVAL;
+	}
+
+	pindesc = kzalloc(sizeof(*pindesc), GFP_KERNEL);
+	if (pindesc == NULL)
+		return -ENOMEM;
+	spin_lock_init(&pindesc->lock);
+
+	/* Set owner */
+	pindesc->pctldev = pctldev;
+
+	/* Copy basic pin info */
+	pindesc->name = name;
+
+	spin_lock(&pctldev->pin_desc_tree_lock);
+	radix_tree_insert(&pctldev->pin_desc_tree, number, pindesc);
+	spin_unlock(&pctldev->pin_desc_tree_lock);
+	pr_debug("registered pin %d (%s) on %s\n",
+		 number, name ? name : "(unnamed)", pctldev->desc->name);
+	return 0;
+}
+
+static int pinctrl_register_pins(struct pinctrl_dev *pctldev,
+				 struct pinctrl_pin_desc const *pins,
+				 unsigned num_descs)
+{
+	unsigned i;
+	int ret = 0;
+
+	for (i = 0; i < num_descs; i++) {
+		ret = pinctrl_register_one_pin(pctldev,
+					       pins[i].number, pins[i].name);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * pinctrl_match_gpio_range() - check if a certain GPIO pin is in range
+ * @pctldev: pin controller device to check
+ * @gpio: gpio pin to check taken from the global GPIO pin space
+ *
+ * Tries to match a GPIO pin number to the ranges handled by a certain pin
+ * controller, return the range or NULL
+ */
+static struct pinctrl_gpio_range *
+pinctrl_match_gpio_range(struct pinctrl_dev *pctldev, unsigned gpio)
+{
+	struct pinctrl_gpio_range *range = NULL;
+
+	/* Loop over the ranges */
+	mutex_lock(&pctldev->gpio_ranges_lock);
+	list_for_each_entry(range, &pctldev->gpio_ranges, node) {
+		/* Check if we're in the valid range */
+		if (gpio >= range->base &&
+		    gpio < range->base + range->npins) {
+			mutex_unlock(&pctldev->gpio_ranges_lock);
+			return range;
+		}
+	}
+	mutex_unlock(&pctldev->gpio_ranges_lock);
+
+	return NULL;
+}
+
+/**
+ * pinctrl_get_device_gpio_range() - find device for GPIO range
+ * @gpio: the pin to locate the pin controller for
+ * @outdev: the pin control device if found
+ * @outrange: the GPIO range if found
+ *
+ * Find the pin controller handling a certain GPIO pin from the pinspace of
+ * the GPIO subsystem, return the device and the matching GPIO range. Returns
+ * negative if the GPIO range could not be found in any device.
+ */
+int pinctrl_get_device_gpio_range(unsigned gpio,
+				struct pinctrl_dev **outdev,
+				struct pinctrl_gpio_range **outrange)
+{
+	struct pinctrl_dev *pctldev = NULL;
+
+	/* Loop over the pin controllers */
+	mutex_lock(&pinctrldev_list_mutex);
+	list_for_each_entry(pctldev, &pinctrldev_list, node) {
+		struct pinctrl_gpio_range *range;
+
+		range = pinctrl_match_gpio_range(pctldev, gpio);
+		if (range != NULL) {
+			*outdev = pctldev;
+			*outrange = range;
+			mutex_unlock(&pinctrldev_list_mutex);
+			return 0;
+		}
+	}
+	mutex_unlock(&pinctrldev_list_mutex);
+
+	return -EINVAL;
+}
+
+/**
+ * pinctrl_add_gpio_range() - register a GPIO range for a controller
+ * @pctldev: pin controller device to add the range to
+ * @range: the GPIO range to add
+ *
+ * This adds a range of GPIOs to be handled by a certain pin controller. Call
+ * this to register handled ranges after registering your pin controller.
+ */
+void pinctrl_add_gpio_range(struct pinctrl_dev *pctldev,
+			    struct pinctrl_gpio_range *range)
+{
+	mutex_lock(&pctldev->gpio_ranges_lock);
+	list_add(&range->node, &pctldev->gpio_ranges);
+	mutex_unlock(&pctldev->gpio_ranges_lock);
+}
+
+/**
+ * pinctrl_remove_gpio_range() - remove a range of GPIOs fro a pin controller
+ * @pctldev: pin controller device to remove the range from
+ * @range: the GPIO range to remove
+ */
+void pinctrl_remove_gpio_range(struct pinctrl_dev *pctldev,
+			       struct pinctrl_gpio_range *range)
+{
+	mutex_lock(&pctldev->gpio_ranges_lock);
+	list_del(&range->node);
+	mutex_unlock(&pctldev->gpio_ranges_lock);
+}
+
+#ifdef CONFIG_DEBUG_FS
+
+static int pinctrl_pins_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev = s->private;
+	const struct pinctrl_ops *ops = pctldev->desc->pctlops;
+	unsigned pin;
+
+	seq_printf(s, "registered pins: %d\n", pctldev->desc->npins);
+	seq_printf(s, "max pin number: %d\n", pctldev->desc->maxpin);
+
+	/* The highest pin number need to be included in the loop, thus <= */
+	for (pin = 0; pin <= pctldev->desc->maxpin; pin++) {
+		struct pin_desc *desc;
+
+		desc = pin_desc_get(pctldev, pin);
+		/* Pin space may be sparse */
+		if (desc == NULL)
+			continue;
+
+		seq_printf(s, "pin %d (%s) ", pin,
+			   desc->name ? desc->name : "unnamed");
+
+		/* Driver-specific info per pin */
+		if (ops->pin_dbg_show)
+			ops->pin_dbg_show(pctldev, s, pin);
+
+		seq_puts(s, "\n");
+	}
+
+	return 0;
+}
+
+static int pinctrl_groups_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev = s->private;
+	const struct pinctrl_ops *ops = pctldev->desc->pctlops;
+	unsigned selector = 0;
+
+	/* No grouping */
+	if (!ops)
+		return 0;
+
+	seq_puts(s, "registered pin groups:\n");
+	while (ops->list_groups(pctldev, selector) >= 0) {
+		const unsigned *pins;
+		unsigned num_pins;
+		const char *gname = ops->get_group_name(pctldev, selector);
+		int ret;
+		int i;
+
+		ret = ops->get_group_pins(pctldev, selector,
+					  &pins, &num_pins);
+		if (ret)
+			seq_printf(s, "%s [ERROR GETTING PINS]\n",
+				   gname);
+		else {
+			seq_printf(s, "group: %s, pins = [ ", gname);
+			for (i = 0; i < num_pins; i++)
+				seq_printf(s, "%d ", pins[i]);
+			seq_puts(s, "]\n");
+		}
+		selector++;
+	}
+
+
+	return 0;
+}
+
+static int pinctrl_gpioranges_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev = s->private;
+	struct pinctrl_gpio_range *range = NULL;
+
+	seq_puts(s, "GPIO ranges handled:\n");
+
+	/* Loop over the ranges */
+	mutex_lock(&pctldev->gpio_ranges_lock);
+	list_for_each_entry(range, &pctldev->gpio_ranges, node) {
+		seq_printf(s, "%u: %s [%u - %u]\n", range->id, range->name,
+			   range->base, (range->base + range->npins - 1));
+	}
+	mutex_unlock(&pctldev->gpio_ranges_lock);
+
+	return 0;
+}
+
+static int pinctrl_devices_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev;
+
+	seq_puts(s, "name [pinmux]\n");
+	mutex_lock(&pinctrldev_list_mutex);
+	list_for_each_entry(pctldev, &pinctrldev_list, node) {
+		seq_printf(s, "%s ", pctldev->desc->name);
+		if (pctldev->desc->pmxops)
+			seq_puts(s, "yes");
+		else
+			seq_puts(s, "no");
+		seq_puts(s, "\n");
+	}
+	mutex_unlock(&pinctrldev_list_mutex);
+
+	return 0;
+}
+
+static int pinctrl_pins_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinctrl_pins_show, inode->i_private);
+}
+
+static int pinctrl_groups_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinctrl_groups_show, inode->i_private);
+}
+
+static int pinctrl_gpioranges_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinctrl_gpioranges_show, inode->i_private);
+}
+
+static int pinctrl_devices_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinctrl_devices_show, NULL);
+}
+
+static const struct file_operations pinctrl_pins_ops = {
+	.open		= pinctrl_pins_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinctrl_groups_ops = {
+	.open		= pinctrl_groups_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinctrl_gpioranges_ops = {
+	.open		= pinctrl_gpioranges_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinctrl_devices_ops = {
+	.open		= pinctrl_devices_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static struct dentry *debugfs_root;
+
+static void pinctrl_init_device_debugfs(struct pinctrl_dev *pctldev)
+{
+	static struct dentry *device_root;
+
+	device_root = debugfs_create_dir(dev_name(&pctldev->dev),
+					 debugfs_root);
+	if (IS_ERR(device_root) || !device_root) {
+		pr_warn("failed to create debugfs directory for %s\n",
+			dev_name(&pctldev->dev));
+		return;
+	}
+	debugfs_create_file("pins", S_IFREG | S_IRUGO,
+			    device_root, pctldev, &pinctrl_pins_ops);
+	debugfs_create_file("pingroups", S_IFREG | S_IRUGO,
+			    device_root, pctldev, &pinctrl_groups_ops);
+	debugfs_create_file("gpio-ranges", S_IFREG | S_IRUGO,
+			    device_root, pctldev, &pinctrl_gpioranges_ops);
+	pinmux_init_device_debugfs(device_root, pctldev);
+}
+
+static void pinctrl_init_debugfs(void)
+{
+	debugfs_root = debugfs_create_dir("pinctrl", NULL);
+	if (IS_ERR(debugfs_root) || !debugfs_root) {
+		pr_warn("failed to create debugfs directory\n");
+		debugfs_root = NULL;
+		return;
+	}
+
+	debugfs_create_file("pinctrl-devices", S_IFREG | S_IRUGO,
+			    debugfs_root, NULL, &pinctrl_devices_ops);
+	pinmux_init_debugfs(debugfs_root);
+}
+
+#else /* CONFIG_DEBUG_FS */
+
+static void pinctrl_init_device_debugfs(struct pinctrl_dev *pctldev)
+{
+}
+
+static void pinctrl_init_debugfs(void)
+{
+}
+
+#endif
+
+/**
+ * pinctrl_register() - register a pin controller device
+ * @pctldesc: descriptor for this pin controller
+ * @dev: parent device for this pin controller
+ * @driver_data: private pin controller data for this pin controller
+ */
+struct pinctrl_dev *pinctrl_register(struct pinctrl_desc *pctldesc,
+				    struct device *dev, void *driver_data)
+{
+	static atomic_t pinmux_no = ATOMIC_INIT(0);
+	struct pinctrl_dev *pctldev;
+	int ret;
+
+	if (pctldesc == NULL)
+		return NULL;
+	if (pctldesc->name == NULL)
+		return NULL;
+
+	/* If we're implementing pinmuxing, check the ops for sanity */
+	if (pctldesc->pmxops) {
+		ret = pinmux_check_ops(pctldesc->pmxops);
+		if (ret) {
+			pr_err("%s pinmux ops lacks necessary functions\n",
+			       pctldesc->name);
+			return NULL;
+		}
+	}
+
+	pctldev = kzalloc(sizeof(struct pinctrl_dev), GFP_KERNEL);
+	if (pctldev == NULL)
+		return NULL;
+
+	/* Initialize pin control device struct */
+	pctldev->owner = pctldesc->owner;
+	pctldev->desc = pctldesc;
+	pctldev->driver_data = driver_data;
+	INIT_RADIX_TREE(&pctldev->pin_desc_tree, GFP_KERNEL);
+	spin_lock_init(&pctldev->pin_desc_tree_lock);
+	INIT_LIST_HEAD(&pctldev->gpio_ranges);
+	mutex_init(&pctldev->gpio_ranges_lock);
+
+	/* Register device */
+	pctldev->dev.parent = dev;
+	dev_set_name(&pctldev->dev, "pinctrl.%d",
+		     atomic_inc_return(&pinmux_no) - 1);
+	pctldev->dev.release = pinctrl_dev_release;
+	ret = device_register(&pctldev->dev);
+	if (ret != 0) {
+		pr_err("error in device registration\n");
+		goto out_reg_dev_err;
+	}
+	dev_set_drvdata(&pctldev->dev, pctldev);
+
+	/* Register all the pins */
+	pr_debug("try to register %d pins on %s...\n",
+		 pctldesc->npins, pctldesc->name);
+	ret = pinctrl_register_pins(pctldev, pctldesc->pins, pctldesc->npins);
+	if (ret) {
+		pr_err("error during pin registration\n");
+		pinctrl_free_pindescs(pctldev, pctldesc->pins,
+				      pctldesc->npins);
+		goto out_reg_pins_err;
+	}
+
+	pinctrl_init_device_debugfs(pctldev);
+	mutex_lock(&pinctrldev_list_mutex);
+	list_add(&pctldev->node, &pinctrldev_list);
+	mutex_unlock(&pinctrldev_list_mutex);
+	pinmux_hog_maps(pctldev);
+	return pctldev;
+
+out_reg_pins_err:
+	device_del(&pctldev->dev);
+out_reg_dev_err:
+	put_device(&pctldev->dev);
+	return NULL;
+}
+EXPORT_SYMBOL_GPL(pinctrl_register);
+
+/**
+ * pinctrl_unregister() - unregister pinmux
+ * @pctldev: pin controller to unregister
+ *
+ * Called by pinmux drivers to unregister a pinmux.
+ */
+void pinctrl_unregister(struct pinctrl_dev *pctldev)
+{
+	if (pctldev == NULL)
+		return;
+
+	pinmux_unhog_maps(pctldev);
+	/* TODO: check that no pinmuxes are still active? */
+	mutex_lock(&pinctrldev_list_mutex);
+	list_del(&pctldev->node);
+	mutex_unlock(&pinctrldev_list_mutex);
+	/* Destroy descriptor tree */
+	pinctrl_free_pindescs(pctldev, pctldev->desc->pins,
+			      pctldev->desc->npins);
+	device_unregister(&pctldev->dev);
+}
+EXPORT_SYMBOL_GPL(pinctrl_unregister);
+
+static int __init pinctrl_init(void)
+{
+	pr_info("initialized pinctrl subsystem\n");
+	pinctrl_init_debugfs();
+	return 0;
+}
+
+/* init early since many drivers really need to initialized pinmux early */
+core_initcall(pinctrl_init);
diff --git a/drivers/pinctrl/core.h b/drivers/pinctrl/core.h
new file mode 100644
index 00000000000000..472fa1341cc0c3
--- /dev/null
+++ b/drivers/pinctrl/core.h
@@ -0,0 +1,71 @@
+/*
+ * Core private header for the pin control subsystem
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+
+/**
+ * struct pinctrl_dev - pin control class device
+ * @node: node to include this pin controller in the global pin controller list
+ * @desc: the pin controller descriptor supplied when initializing this pin
+ *	controller
+ * @pin_desc_tree: each pin descriptor for this pin controller is stored in
+ *	this radix tree
+ * @pin_desc_tree_lock: lock for the descriptor tree
+ * @gpio_ranges: a list of GPIO ranges that is handled by this pin controller,
+ *	ranges are added to this list at runtime
+ * @gpio_ranges_lock: lock for the GPIO ranges list
+ * @dev: the device entry for this pin controller
+ * @owner: module providing the pin controller, used for refcounting
+ * @driver_data: driver data for drivers registering to the pin controller
+ *	subsystem
+ * @pinmux_hogs_lock: lock for the pinmux hog list
+ * @pinmux_hogs: list of pinmux maps hogged by this device
+ */
+struct pinctrl_dev {
+	struct list_head node;
+	struct pinctrl_desc *desc;
+	struct radix_tree_root pin_desc_tree;
+	spinlock_t pin_desc_tree_lock;
+	struct list_head gpio_ranges;
+	struct mutex gpio_ranges_lock;
+	struct device dev;
+	struct module *owner;
+	void *driver_data;
+#ifdef CONFIG_PINMUX
+	struct mutex pinmux_hogs_lock;
+	struct list_head pinmux_hogs;
+#endif
+};
+
+/**
+ * struct pin_desc - pin descriptor for each physical pin in the arch
+ * @pctldev: corresponding pin control device
+ * @name: a name for the pin, e.g. the name of the pin/pad/finger on a
+ *	datasheet or such
+ * @lock: a lock to protect the descriptor structure
+ * @mux_requested: whether the pin is already requested by pinmux or not
+ * @mux_function: a named muxing function for the pin that will be passed to
+ *	subdrivers and shown in debugfs etc
+ */
+struct pin_desc {
+	struct pinctrl_dev *pctldev;
+	const char *name;
+	spinlock_t lock;
+	/* These fields only added when supporting pinmux drivers */
+#ifdef CONFIG_PINMUX
+	const char *mux_function;
+#endif
+};
+
+struct pinctrl_dev *get_pinctrl_dev_from_dev(struct device *dev,
+					     const char *dev_name);
+struct pin_desc *pin_desc_get(struct pinctrl_dev *pctldev, int pin);
+int pinctrl_get_device_gpio_range(unsigned gpio,
+				  struct pinctrl_dev **outdev,
+				  struct pinctrl_gpio_range **outrange);
diff --git a/drivers/pinctrl/pinmux-sirf.c b/drivers/pinctrl/pinmux-sirf.c
new file mode 100644
index 00000000000000..d76cae62095690
--- /dev/null
+++ b/drivers/pinctrl/pinmux-sirf.c
@@ -0,0 +1,1215 @@
+/*
+ * pinmux driver for CSR SiRFprimaII
+ *
+ * Copyright (c) 2011 Cambridge Silicon Radio Limited, a CSR plc group company.
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/bitops.h>
+
+#define DRIVER_NAME "pinmux-sirf"
+
+#define SIRFSOC_NUM_PADS    622
+#define SIRFSOC_GPIO_PAD_EN(g) ((g)*0x100 + 0x84)
+#define SIRFSOC_RSC_PIN_MUX 0x4
+
+/*
+ * pad list for the pinmux subsystem
+ * refer to CS-131858-DC-6A.xls
+ */
+static const struct pinctrl_pin_desc sirfsoc_pads[] = {
+	PINCTRL_PIN(4, "pwm0"),
+	PINCTRL_PIN(5, "pwm1"),
+	PINCTRL_PIN(6, "pwm2"),
+	PINCTRL_PIN(7, "pwm3"),
+	PINCTRL_PIN(8, "warm_rst_b"),
+	PINCTRL_PIN(9, "odo_0"),
+	PINCTRL_PIN(10, "odo_1"),
+	PINCTRL_PIN(11, "dr_dir"),
+	PINCTRL_PIN(13, "scl_1"),
+	PINCTRL_PIN(15, "sda_1"),
+	PINCTRL_PIN(16, "x_ldd[16]"),
+	PINCTRL_PIN(17, "x_ldd[17]"),
+	PINCTRL_PIN(18, "x_ldd[18]"),
+	PINCTRL_PIN(19, "x_ldd[19]"),
+	PINCTRL_PIN(20, "x_ldd[20]"),
+	PINCTRL_PIN(21, "x_ldd[21]"),
+	PINCTRL_PIN(22, "x_ldd[22]"),
+	PINCTRL_PIN(23, "x_ldd[23], lcdrom_frdy"),
+	PINCTRL_PIN(24, "gps_sgn"),
+	PINCTRL_PIN(25, "gps_mag"),
+	PINCTRL_PIN(26, "gps_clk"),
+	PINCTRL_PIN(27,	"sd_cd_b_1"),
+	PINCTRL_PIN(28, "sd_vcc_on_1"),
+	PINCTRL_PIN(29, "sd_wp_b_1"),
+	PINCTRL_PIN(30, "sd_clk_3"),
+	PINCTRL_PIN(31, "sd_cmd_3"),
+
+	PINCTRL_PIN(32, "x_sd_dat_3[0]"),
+	PINCTRL_PIN(33, "x_sd_dat_3[1]"),
+	PINCTRL_PIN(34, "x_sd_dat_3[2]"),
+	PINCTRL_PIN(35, "x_sd_dat_3[3]"),
+	PINCTRL_PIN(36, "x_sd_clk_4"),
+	PINCTRL_PIN(37, "x_sd_cmd_4"),
+	PINCTRL_PIN(38, "x_sd_dat_4[0]"),
+	PINCTRL_PIN(39, "x_sd_dat_4[1]"),
+	PINCTRL_PIN(40, "x_sd_dat_4[2]"),
+	PINCTRL_PIN(41, "x_sd_dat_4[3]"),
+	PINCTRL_PIN(42, "x_cko_1"),
+	PINCTRL_PIN(43, "x_ac97_bit_clk"),
+	PINCTRL_PIN(44, "x_ac97_dout"),
+	PINCTRL_PIN(45, "x_ac97_din"),
+	PINCTRL_PIN(46, "x_ac97_sync"),
+	PINCTRL_PIN(47, "x_txd_1"),
+	PINCTRL_PIN(48, "x_txd_2"),
+	PINCTRL_PIN(49, "x_rxd_1"),
+	PINCTRL_PIN(50, "x_rxd_2"),
+	PINCTRL_PIN(51, "x_usclk_0"),
+	PINCTRL_PIN(52, "x_utxd_0"),
+	PINCTRL_PIN(53, "x_urxd_0"),
+	PINCTRL_PIN(54, "x_utfs_0"),
+	PINCTRL_PIN(55, "x_urfs_0"),
+	PINCTRL_PIN(56, "x_usclk_1"),
+	PINCTRL_PIN(57, "x_utxd_1"),
+	PINCTRL_PIN(58, "x_urxd_1"),
+	PINCTRL_PIN(59, "x_utfs_1"),
+	PINCTRL_PIN(60, "x_urfs_1"),
+	PINCTRL_PIN(61, "x_usclk_2"),
+	PINCTRL_PIN(62, "x_utxd_2"),
+	PINCTRL_PIN(63, "x_urxd_2"),
+
+	PINCTRL_PIN(64, "x_utfs_2"),
+	PINCTRL_PIN(65, "x_urfs_2"),
+	PINCTRL_PIN(66, "x_df_we_b"),
+	PINCTRL_PIN(67, "x_df_re_b"),
+	PINCTRL_PIN(68, "x_txd_0"),
+	PINCTRL_PIN(69, "x_rxd_0"),
+	PINCTRL_PIN(78, "x_cko_0"),
+	PINCTRL_PIN(79, "x_vip_pxd[7]"),
+	PINCTRL_PIN(80, "x_vip_pxd[6]"),
+	PINCTRL_PIN(81, "x_vip_pxd[5]"),
+	PINCTRL_PIN(82, "x_vip_pxd[4]"),
+	PINCTRL_PIN(83, "x_vip_pxd[3]"),
+	PINCTRL_PIN(84, "x_vip_pxd[2]"),
+	PINCTRL_PIN(85, "x_vip_pxd[1]"),
+	PINCTRL_PIN(86, "x_vip_pxd[0]"),
+	PINCTRL_PIN(87, "x_vip_vsync"),
+	PINCTRL_PIN(88, "x_vip_hsync"),
+	PINCTRL_PIN(89, "x_vip_pxclk"),
+	PINCTRL_PIN(90, "x_sda_0"),
+	PINCTRL_PIN(91, "x_scl_0"),
+	PINCTRL_PIN(92, "x_df_ry_by"),
+	PINCTRL_PIN(93, "x_df_cs_b[1]"),
+	PINCTRL_PIN(94, "x_df_cs_b[0]"),
+	PINCTRL_PIN(95, "x_l_pclk"),
+
+	PINCTRL_PIN(96, "x_l_lck"),
+	PINCTRL_PIN(97, "x_l_fck"),
+	PINCTRL_PIN(98, "x_l_de"),
+	PINCTRL_PIN(99, "x_ldd[0]"),
+	PINCTRL_PIN(100, "x_ldd[1]"),
+	PINCTRL_PIN(101, "x_ldd[2]"),
+	PINCTRL_PIN(102, "x_ldd[3]"),
+	PINCTRL_PIN(103, "x_ldd[4]"),
+	PINCTRL_PIN(104, "x_ldd[5]"),
+	PINCTRL_PIN(105, "x_ldd[6]"),
+	PINCTRL_PIN(106, "x_ldd[7]"),
+	PINCTRL_PIN(107, "x_ldd[8]"),
+	PINCTRL_PIN(108, "x_ldd[9]"),
+	PINCTRL_PIN(109, "x_ldd[10]"),
+	PINCTRL_PIN(110, "x_ldd[11]"),
+	PINCTRL_PIN(111, "x_ldd[12]"),
+	PINCTRL_PIN(112, "x_ldd[13]"),
+	PINCTRL_PIN(113, "x_ldd[14]"),
+	PINCTRL_PIN(114, "x_ldd[15]"),
+};
+
+/**
+ * @dev: a pointer back to containing device
+ * @virtbase: the offset to the controller in virtual memory
+ */
+struct sirfsoc_pmx {
+	struct device *dev;
+	struct pinctrl_dev *pmx;
+	void __iomem *gpio_virtbase;
+	void __iomem *rsc_virtbase;
+};
+
+/* SIRFSOC_GPIO_PAD_EN set */
+struct sirfsoc_muxmask {
+	unsigned long group;
+	unsigned long mask;
+};
+
+struct sirfsoc_padmux {
+	unsigned long muxmask_counts;
+	const struct sirfsoc_muxmask *muxmask;
+	/* RSC_PIN_MUX set */
+	unsigned long funcmask;
+	unsigned long funcval;
+};
+
+ /**
+ * struct sirfsoc_pin_group - describes a SiRFprimaII pin group
+ * @name: the name of this specific pin group
+ * @pins: an array of discrete physical pins used in this group, taken
+ *	from the driver-local pin enumeration space
+ * @num_pins: the number of pins in this group array, i.e. the number of
+ *	elements in .pins so we can iterate over that array
+ */
+struct sirfsoc_pin_group {
+	const char *name;
+	const unsigned int *pins;
+	const unsigned num_pins;
+};
+
+static const struct sirfsoc_muxmask lcd_16bits_sirfsoc_muxmask[] = {
+	{
+		.group = 3,
+		.mask = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) |
+			BIT(9) | BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(15) | BIT(16) |
+			BIT(17) | BIT(18),
+	}, {
+		.group = 2,
+		.mask = BIT(31),
+	},
+};
+
+static const struct sirfsoc_padmux lcd_16bits_padmux = {
+	.muxmask_counts = ARRAY_SIZE(lcd_16bits_sirfsoc_muxmask),
+	.muxmask = lcd_16bits_sirfsoc_muxmask,
+	.funcmask = BIT(4),
+	.funcval = 0,
+};
+
+static const unsigned lcd_16bits_pins[] = { 95, 96, 97, 98, 99, 100, 101, 102, 103, 104,
+	105, 106, 107, 108, 109, 110, 111, 112, 113, 114 };
+
+static const struct sirfsoc_muxmask lcd_18bits_muxmask[] = {
+	{
+		.group = 3,
+		.mask = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) |
+			BIT(9) | BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(15) | BIT(16) |
+			BIT(17) | BIT(18),
+	}, {
+		.group = 2,
+		.mask = BIT(31),
+	}, {
+		.group = 0,
+		.mask = BIT(16) | BIT(17),
+	},
+};
+
+static const struct sirfsoc_padmux lcd_18bits_padmux = {
+	.muxmask_counts = ARRAY_SIZE(lcd_18bits_muxmask),
+	.muxmask = lcd_18bits_muxmask,
+	.funcmask = BIT(4),
+	.funcval = 0,
+};
+
+static const unsigned lcd_18bits_pins[] = { 16, 17, 95, 96, 97, 98, 99, 100, 101, 102, 103, 104,
+	105, 106, 107, 108, 109, 110, 111, 112, 113, 114};
+
+static const struct sirfsoc_muxmask lcd_24bits_muxmask[] = {
+	{
+		.group = 3,
+		.mask = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) |
+			BIT(9) | BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(15) | BIT(16) |
+			BIT(17) | BIT(18),
+	}, {
+		.group = 2,
+		.mask = BIT(31),
+	}, {
+		.group = 0,
+		.mask = BIT(16) | BIT(17) | BIT(18) | BIT(19) | BIT(20) | BIT(21) | BIT(22) | BIT(23),
+	},
+};
+
+static const struct sirfsoc_padmux lcd_24bits_padmux = {
+	.muxmask_counts = ARRAY_SIZE(lcd_24bits_muxmask),
+	.muxmask = lcd_24bits_muxmask,
+	.funcmask = BIT(4),
+	.funcval = 0,
+};
+
+static const unsigned lcd_24bits_pins[] = { 16, 17, 18, 19, 20, 21, 22, 23, 95, 96, 97, 98, 99, 100, 101, 102, 103, 104,
+	105, 106, 107, 108, 109, 110, 111, 112, 113, 114 };
+
+static const struct sirfsoc_muxmask lcdrom_muxmask[] = {
+	{
+		.group = 3,
+		.mask = BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) |
+			BIT(9) | BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(15) | BIT(16) |
+			BIT(17) | BIT(18),
+	}, {
+		.group = 2,
+		.mask = BIT(31),
+	}, {
+		.group = 0,
+		.mask = BIT(23),
+	},
+};
+
+static const struct sirfsoc_padmux lcdrom_padmux = {
+	.muxmask_counts = ARRAY_SIZE(lcdrom_muxmask),
+	.muxmask = lcdrom_muxmask,
+	.funcmask = BIT(4),
+	.funcval = BIT(4),
+};
+
+static const unsigned lcdrom_pins[] = { 23, 95, 96, 97, 98, 99, 100, 101, 102, 103, 104,
+	105, 106, 107, 108, 109, 110, 111, 112, 113, 114 };
+
+static const struct sirfsoc_muxmask uart0_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(4) | BIT(5),
+	}, {
+		.group = 1,
+		.mask = BIT(23) | BIT(28),
+	},
+};
+
+static const struct sirfsoc_padmux uart0_padmux = {
+	.muxmask_counts = ARRAY_SIZE(uart0_muxmask),
+	.muxmask = uart0_muxmask,
+	.funcmask = BIT(9),
+	.funcval = BIT(9),
+};
+
+static const unsigned uart0_pins[] = { 55, 60, 68, 69 };
+
+static const struct sirfsoc_muxmask uart0_nostreamctrl_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(4) | BIT(5),
+	},
+};
+
+static const struct sirfsoc_padmux uart0_nostreamctrl_padmux = {
+	.muxmask_counts = ARRAY_SIZE(uart0_nostreamctrl_muxmask),
+	.muxmask = uart0_nostreamctrl_muxmask,
+};
+
+static const unsigned uart0_nostreamctrl_pins[] = { 68, 39 };
+
+static const struct sirfsoc_muxmask uart1_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(15) | BIT(17),
+	},
+};
+
+static const struct sirfsoc_padmux uart1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(uart1_muxmask),
+	.muxmask = uart1_muxmask,
+};
+
+static const unsigned uart1_pins[] = { 47, 49 };
+
+static const struct sirfsoc_muxmask uart2_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(16) | BIT(18) | BIT(24) | BIT(27),
+	},
+};
+
+static const struct sirfsoc_padmux uart2_padmux = {
+	.muxmask_counts = ARRAY_SIZE(uart2_muxmask),
+	.muxmask = uart2_muxmask,
+	.funcmask = BIT(10),
+	.funcval = BIT(10),
+};
+
+static const unsigned uart2_pins[] = { 48, 50, 56, 59 };
+
+static const struct sirfsoc_muxmask uart2_nostreamctrl_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(16) | BIT(18),
+	},
+};
+
+static const struct sirfsoc_padmux uart2_nostreamctrl_padmux = {
+	.muxmask_counts = ARRAY_SIZE(uart2_nostreamctrl_muxmask),
+	.muxmask = uart2_nostreamctrl_muxmask,
+};
+
+static const unsigned uart2_nostreamctrl_pins[] = { 48, 50 };
+
+static const struct sirfsoc_muxmask sdmmc3_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(30) | BIT(31),
+	}, {
+		.group = 1,
+		.mask = BIT(0) | BIT(1) | BIT(2) | BIT(3),
+	},
+};
+
+static const struct sirfsoc_padmux sdmmc3_padmux = {
+	.muxmask_counts = ARRAY_SIZE(sdmmc3_muxmask),
+	.muxmask = sdmmc3_muxmask,
+	.funcmask = BIT(7),
+	.funcval = 0,
+};
+
+static const unsigned sdmmc3_pins[] = { 30, 31, 32, 33, 34, 35 };
+
+static const struct sirfsoc_muxmask spi0_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(0) | BIT(1) | BIT(2) | BIT(3),
+	},
+};
+
+static const struct sirfsoc_padmux spi0_padmux = {
+	.muxmask_counts = ARRAY_SIZE(spi0_muxmask),
+	.muxmask = spi0_muxmask,
+	.funcmask = BIT(7),
+	.funcval = BIT(7),
+};
+
+static const unsigned spi0_pins[] = { 32, 33, 34, 35 };
+
+static const struct sirfsoc_muxmask sdmmc4_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) | BIT(9),
+	},
+};
+
+static const struct sirfsoc_padmux sdmmc4_padmux = {
+	.muxmask_counts = ARRAY_SIZE(sdmmc4_muxmask),
+	.muxmask = sdmmc4_muxmask,
+};
+
+static const unsigned sdmmc4_pins[] = { 36, 37, 38, 39, 40, 41 };
+
+static const struct sirfsoc_muxmask cko1_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(10),
+	},
+};
+
+static const struct sirfsoc_padmux cko1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(cko1_muxmask),
+	.muxmask = cko1_muxmask,
+	.funcmask = BIT(3),
+	.funcval = 0,
+};
+
+static const unsigned cko1_pins[] = { 42 };
+
+static const struct sirfsoc_muxmask i2s_muxmask[] = {
+	{
+		.group = 1,
+		.mask =
+			BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(19)
+				| BIT(23) | BIT(28),
+	},
+};
+
+static const struct sirfsoc_padmux i2s_padmux = {
+	.muxmask_counts = ARRAY_SIZE(i2s_muxmask),
+	.muxmask = i2s_muxmask,
+	.funcmask = BIT(3) | BIT(9),
+	.funcval = BIT(3),
+};
+
+static const unsigned i2s_pins[] = { 42, 43, 44, 45, 46, 51, 55, 60 };
+
+static const struct sirfsoc_muxmask ac97_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(11) | BIT(12) | BIT(13) | BIT(14),
+	},
+};
+
+static const struct sirfsoc_padmux ac97_padmux = {
+	.muxmask_counts = ARRAY_SIZE(ac97_muxmask),
+	.muxmask = ac97_muxmask,
+	.funcmask = BIT(8),
+	.funcval = 0,
+};
+
+static const unsigned ac97_pins[] = { 33, 34, 35, 36 };
+
+static const struct sirfsoc_muxmask spi1_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(11) | BIT(12) | BIT(13) | BIT(14),
+	},
+};
+
+static const struct sirfsoc_padmux spi1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(spi1_muxmask),
+	.muxmask = spi1_muxmask,
+	.funcmask = BIT(8),
+	.funcval = BIT(8),
+};
+
+static const unsigned spi1_pins[] = { 33, 34, 35, 36 };
+
+static const struct sirfsoc_muxmask sdmmc1_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(27) | BIT(28) | BIT(29),
+	},
+};
+
+static const struct sirfsoc_padmux sdmmc1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(sdmmc1_muxmask),
+	.muxmask = sdmmc1_muxmask,
+};
+
+static const unsigned sdmmc1_pins[] = { 27, 28, 29 };
+
+static const struct sirfsoc_muxmask gps_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(24) | BIT(25) | BIT(26),
+	},
+};
+
+static const struct sirfsoc_padmux gps_padmux = {
+	.muxmask_counts = ARRAY_SIZE(gps_muxmask),
+	.muxmask = gps_muxmask,
+	.funcmask = BIT(12) | BIT(13) | BIT(14),
+	.funcval = BIT(12),
+};
+
+static const unsigned gps_pins[] = { 24, 25, 26 };
+
+static const struct sirfsoc_muxmask sdmmc5_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(24) | BIT(25) | BIT(26),
+	}, {
+		.group = 1,
+		.mask = BIT(29),
+	}, {
+		.group = 2,
+		.mask = BIT(0) | BIT(1),
+	},
+};
+
+static const struct sirfsoc_padmux sdmmc5_padmux = {
+	.muxmask_counts = ARRAY_SIZE(sdmmc5_muxmask),
+	.muxmask = sdmmc5_muxmask,
+	.funcmask = BIT(13) | BIT(14),
+	.funcval = BIT(13) | BIT(14),
+};
+
+static const unsigned sdmmc5_pins[] = { 24, 25, 26, 61, 64, 65 };
+
+static const struct sirfsoc_muxmask usp0_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(19) | BIT(20) | BIT(21) | BIT(22) | BIT(23),
+	},
+};
+
+static const struct sirfsoc_padmux usp0_padmux = {
+	.muxmask_counts = ARRAY_SIZE(usp0_muxmask),
+	.muxmask = usp0_muxmask,
+	.funcmask = BIT(1) | BIT(2) | BIT(6) | BIT(9),
+	.funcval = 0,
+};
+
+static const unsigned usp0_pins[] = { 51, 52, 53, 54, 55 };
+
+static const struct sirfsoc_muxmask usp1_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(24) | BIT(25) | BIT(26) | BIT(27) | BIT(28),
+	},
+};
+
+static const struct sirfsoc_padmux usp1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(usp1_muxmask),
+	.muxmask = usp1_muxmask,
+	.funcmask = BIT(1) | BIT(9) | BIT(10) | BIT(11),
+	.funcval = 0,
+};
+
+static const unsigned usp1_pins[] = { 56, 57, 58, 59, 60 };
+
+static const struct sirfsoc_muxmask usp2_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(29) | BIT(30) | BIT(31),
+	}, {
+		.group = 2,
+		.mask = BIT(0) | BIT(1),
+	},
+};
+
+static const struct sirfsoc_padmux usp2_padmux = {
+	.muxmask_counts = ARRAY_SIZE(usp2_muxmask),
+	.muxmask = usp2_muxmask,
+	.funcmask = BIT(13) | BIT(14),
+	.funcval = 0,
+};
+
+static const unsigned usp2_pins[] = { 61, 62, 63, 64, 65 };
+
+static const struct sirfsoc_muxmask nand_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(2) | BIT(3) | BIT(28) | BIT(29) | BIT(30),
+	},
+};
+
+static const struct sirfsoc_padmux nand_padmux = {
+	.muxmask_counts = ARRAY_SIZE(nand_muxmask),
+	.muxmask = nand_muxmask,
+	.funcmask = BIT(5),
+	.funcval = 0,
+};
+
+static const unsigned nand_pins[] = { 64, 65, 92, 93, 94 };
+
+static const struct sirfsoc_padmux sdmmc0_padmux = {
+	.muxmask_counts = 0,
+	.funcmask = BIT(5),
+	.funcval = 0,
+};
+
+static const unsigned sdmmc0_pins[] = { };
+
+static const struct sirfsoc_muxmask sdmmc2_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(2) | BIT(3),
+	},
+};
+
+static const struct sirfsoc_padmux sdmmc2_padmux = {
+	.muxmask_counts = ARRAY_SIZE(sdmmc2_muxmask),
+	.muxmask = sdmmc2_muxmask,
+	.funcmask = BIT(5),
+	.funcval = BIT(5),
+};
+
+static const unsigned sdmmc2_pins[] = { 66, 67 };
+
+static const struct sirfsoc_muxmask cko0_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(14),
+	},
+};
+
+static const struct sirfsoc_padmux cko0_padmux = {
+	.muxmask_counts = ARRAY_SIZE(cko0_muxmask),
+	.muxmask = cko0_muxmask,
+};
+
+static const unsigned cko0_pins[] = { 78 };
+
+static const struct sirfsoc_muxmask vip_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(15) | BIT(16) | BIT(17) | BIT(18) | BIT(19)
+			| BIT(20) | BIT(21) | BIT(22) | BIT(23) | BIT(24) |
+			BIT(25),
+	},
+};
+
+static const struct sirfsoc_padmux vip_padmux = {
+	.muxmask_counts = ARRAY_SIZE(vip_muxmask),
+	.muxmask = vip_muxmask,
+	.funcmask = BIT(0),
+	.funcval = 0,
+};
+
+static const unsigned vip_pins[] = { 79, 80, 81, 82, 83, 84, 85, 86, 87, 88, 89 };
+
+static const struct sirfsoc_muxmask i2c0_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(26) | BIT(27),
+	},
+};
+
+static const struct sirfsoc_padmux i2c0_padmux = {
+	.muxmask_counts = ARRAY_SIZE(i2c0_muxmask),
+	.muxmask = i2c0_muxmask,
+};
+
+static const unsigned i2c0_pins[] = { 90, 91 };
+
+static const struct sirfsoc_muxmask i2c1_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(13) | BIT(15),
+	},
+};
+
+static const struct sirfsoc_padmux i2c1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(i2c1_muxmask),
+	.muxmask = i2c1_muxmask,
+};
+
+static const unsigned i2c1_pins[] = { 13, 15 };
+
+static const struct sirfsoc_muxmask viprom_muxmask[] = {
+	{
+		.group = 2,
+		.mask = BIT(15) | BIT(16) | BIT(17) | BIT(18) | BIT(19)
+			| BIT(20) | BIT(21) | BIT(22) | BIT(23) | BIT(24) |
+			BIT(25),
+	}, {
+		.group = 0,
+		.mask = BIT(12),
+	},
+};
+
+static const struct sirfsoc_padmux viprom_padmux = {
+	.muxmask_counts = ARRAY_SIZE(viprom_muxmask),
+	.muxmask = viprom_muxmask,
+	.funcmask = BIT(0),
+	.funcval = BIT(0),
+};
+
+static const unsigned viprom_pins[] = { 12, 79, 80, 81, 82, 83, 84, 85, 86, 87, 88, 89 };
+
+static const struct sirfsoc_muxmask pwm0_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(4),
+	},
+};
+
+static const struct sirfsoc_padmux pwm0_padmux = {
+	.muxmask_counts = ARRAY_SIZE(pwm0_muxmask),
+	.muxmask = pwm0_muxmask,
+	.funcmask = BIT(12),
+	.funcval = 0,
+};
+
+static const unsigned pwm0_pins[] = { 4 };
+
+static const struct sirfsoc_muxmask pwm1_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(5),
+	},
+};
+
+static const struct sirfsoc_padmux pwm1_padmux = {
+	.muxmask_counts = ARRAY_SIZE(pwm1_muxmask),
+	.muxmask = pwm1_muxmask,
+};
+
+static const unsigned pwm1_pins[] = { 5 };
+
+static const struct sirfsoc_muxmask pwm2_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(6),
+	},
+};
+
+static const struct sirfsoc_padmux pwm2_padmux = {
+	.muxmask_counts = ARRAY_SIZE(pwm2_muxmask),
+	.muxmask = pwm2_muxmask,
+};
+
+static const unsigned pwm2_pins[] = { 6 };
+
+static const struct sirfsoc_muxmask pwm3_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(7),
+	},
+};
+
+static const struct sirfsoc_padmux pwm3_padmux = {
+	.muxmask_counts = ARRAY_SIZE(pwm3_muxmask),
+	.muxmask = pwm3_muxmask,
+};
+
+static const unsigned pwm3_pins[] = { 7 };
+
+static const struct sirfsoc_muxmask warm_rst_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(8),
+	},
+};
+
+static const struct sirfsoc_padmux warm_rst_padmux = {
+	.muxmask_counts = ARRAY_SIZE(warm_rst_muxmask),
+	.muxmask = warm_rst_muxmask,
+};
+
+static const unsigned warm_rst_pins[] = { 8 };
+
+static const struct sirfsoc_muxmask usb0_utmi_drvbus_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(22),
+	},
+};
+static const struct sirfsoc_padmux usb0_utmi_drvbus_padmux = {
+	.muxmask_counts = ARRAY_SIZE(usb0_utmi_drvbus_muxmask),
+	.muxmask = usb0_utmi_drvbus_muxmask,
+	.funcmask = BIT(6),
+	.funcval = BIT(6), /* refer to PAD_UTMI_DRVVBUS0_ENABLE */
+};
+
+static const unsigned usb0_utmi_drvbus_pins[] = { 54 };
+
+static const struct sirfsoc_muxmask usb1_utmi_drvbus_muxmask[] = {
+	{
+		.group = 1,
+		.mask = BIT(27),
+	},
+};
+
+static const struct sirfsoc_padmux usb1_utmi_drvbus_padmux = {
+	.muxmask_counts = ARRAY_SIZE(usb1_utmi_drvbus_muxmask),
+	.muxmask = usb1_utmi_drvbus_muxmask,
+	.funcmask = BIT(11),
+	.funcval = BIT(11), /* refer to PAD_UTMI_DRVVBUS1_ENABLE */
+};
+
+static const unsigned usb1_utmi_drvbus_pins[] = { 59 };
+
+static const struct sirfsoc_muxmask pulse_count_muxmask[] = {
+	{
+		.group = 0,
+		.mask = BIT(9) | BIT(10) | BIT(11),
+	},
+};
+
+static const struct sirfsoc_padmux pulse_count_padmux = {
+	.muxmask_counts = ARRAY_SIZE(pulse_count_muxmask),
+	.muxmask = pulse_count_muxmask,
+};
+
+static const unsigned pulse_count_pins[] = { 9, 10, 11 };
+
+#define SIRFSOC_PIN_GROUP(n, p)  \
+	{			\
+		.name = n,	\
+		.pins = p,	\
+		.num_pins = ARRAY_SIZE(p),	\
+	}
+
+static const struct sirfsoc_pin_group sirfsoc_pin_groups[] = {
+	SIRFSOC_PIN_GROUP("lcd_16bitsgrp", lcd_16bits_pins),
+	SIRFSOC_PIN_GROUP("lcd_18bitsgrp", lcd_18bits_pins),
+	SIRFSOC_PIN_GROUP("lcd_24bitsgrp", lcd_24bits_pins),
+	SIRFSOC_PIN_GROUP("lcdrom_grp", lcdrom_pins),
+	SIRFSOC_PIN_GROUP("uart0grp", uart0_pins),
+	SIRFSOC_PIN_GROUP("uart1grp", uart1_pins),
+	SIRFSOC_PIN_GROUP("uart2grp", uart2_pins),
+	SIRFSOC_PIN_GROUP("uart2_nostreamctrlgrp", uart2_nostreamctrl_pins),
+	SIRFSOC_PIN_GROUP("usp0grp", usp0_pins),
+	SIRFSOC_PIN_GROUP("usp1grp", usp1_pins),
+	SIRFSOC_PIN_GROUP("usp2grp", usp2_pins),
+	SIRFSOC_PIN_GROUP("i2c0grp", i2c0_pins),
+	SIRFSOC_PIN_GROUP("i2c1grp", i2c1_pins),
+	SIRFSOC_PIN_GROUP("pwm0grp", pwm0_pins),
+	SIRFSOC_PIN_GROUP("pwm1grp", pwm1_pins),
+	SIRFSOC_PIN_GROUP("pwm2grp", pwm2_pins),
+	SIRFSOC_PIN_GROUP("pwm3grp", pwm3_pins),
+	SIRFSOC_PIN_GROUP("vipgrp", vip_pins),
+	SIRFSOC_PIN_GROUP("vipromgrp", viprom_pins),
+	SIRFSOC_PIN_GROUP("warm_rstgrp", warm_rst_pins),
+	SIRFSOC_PIN_GROUP("cko0_rstgrp", cko0_pins),
+	SIRFSOC_PIN_GROUP("cko1_rstgrp", cko1_pins),
+	SIRFSOC_PIN_GROUP("sdmmc0grp", sdmmc0_pins),
+	SIRFSOC_PIN_GROUP("sdmmc1grp", sdmmc1_pins),
+	SIRFSOC_PIN_GROUP("sdmmc2grp", sdmmc2_pins),
+	SIRFSOC_PIN_GROUP("sdmmc3grp", sdmmc3_pins),
+	SIRFSOC_PIN_GROUP("sdmmc4grp", sdmmc4_pins),
+	SIRFSOC_PIN_GROUP("sdmmc5grp", sdmmc5_pins),
+	SIRFSOC_PIN_GROUP("usb0_utmi_drvbusgrp", usb0_utmi_drvbus_pins),
+	SIRFSOC_PIN_GROUP("usb1_utmi_drvbusgrp", usb1_utmi_drvbus_pins),
+	SIRFSOC_PIN_GROUP("pulse_countgrp", pulse_count_pins),
+	SIRFSOC_PIN_GROUP("i2sgrp", i2s_pins),
+	SIRFSOC_PIN_GROUP("ac97grp", ac97_pins),
+	SIRFSOC_PIN_GROUP("nandgrp", nand_pins),
+	SIRFSOC_PIN_GROUP("spi0grp", spi0_pins),
+	SIRFSOC_PIN_GROUP("spi1grp", spi1_pins),
+	SIRFSOC_PIN_GROUP("gpsgrp", gps_pins),
+};
+
+static int sirfsoc_list_groups(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(sirfsoc_pin_groups))
+		return -EINVAL;
+	return 0;
+}
+
+static const char *sirfsoc_get_group_name(struct pinctrl_dev *pctldev,
+				       unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(sirfsoc_pin_groups))
+		return NULL;
+	return sirfsoc_pin_groups[selector].name;
+}
+
+static int sirfsoc_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
+			       const unsigned **pins,
+			       unsigned *num_pins)
+{
+	if (selector >= ARRAY_SIZE(sirfsoc_pin_groups))
+		return -EINVAL;
+	*pins = sirfsoc_pin_groups[selector].pins;
+	*num_pins = sirfsoc_pin_groups[selector].num_pins;
+	return 0;
+}
+
+static void sirfsoc_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
+		   unsigned offset)
+{
+	seq_printf(s, " " DRIVER_NAME);
+}
+
+static struct pinctrl_ops sirfsoc_pctrl_ops = {
+	.list_groups = sirfsoc_list_groups,
+	.get_group_name = sirfsoc_get_group_name,
+	.get_group_pins = sirfsoc_get_group_pins,
+	.pin_dbg_show = sirfsoc_pin_dbg_show,
+};
+
+struct sirfsoc_pmx_func {
+	const char *name;
+	const char * const *groups;
+	const unsigned num_groups;
+	const struct sirfsoc_padmux *padmux;
+};
+
+static const char * const lcd_16bitsgrp[] = { "lcd_16bitsgrp" };
+static const char * const lcd_18bitsgrp[] = { "lcd_18bitsgrp" };
+static const char * const lcd_24bitsgrp[] = { "lcd_24bitsgrp" };
+static const char * const lcdromgrp[] = { "lcdromgrp" };
+static const char * const uart0grp[] = { "uart0grp" };
+static const char * const uart1grp[] = { "uart1grp" };
+static const char * const uart2grp[] = { "uart2grp" };
+static const char * const uart2_nostreamctrlgrp[] = { "uart2_nostreamctrlgrp" };
+static const char * const usp0grp[] = { "usp0grp" };
+static const char * const usp1grp[] = { "usp1grp" };
+static const char * const usp2grp[] = { "usp2grp" };
+static const char * const i2c0grp[] = { "i2c0grp" };
+static const char * const i2c1grp[] = { "i2c1grp" };
+static const char * const pwm0grp[] = { "pwm0grp" };
+static const char * const pwm1grp[] = { "pwm1grp" };
+static const char * const pwm2grp[] = { "pwm2grp" };
+static const char * const pwm3grp[] = { "pwm3grp" };
+static const char * const vipgrp[] = { "vipgrp" };
+static const char * const vipromgrp[] = { "vipromgrp" };
+static const char * const warm_rstgrp[] = { "warm_rstgrp" };
+static const char * const cko0grp[] = { "cko0grp" };
+static const char * const cko1grp[] = { "cko1grp" };
+static const char * const sdmmc0grp[] = { "sdmmc0grp" };
+static const char * const sdmmc1grp[] = { "sdmmc1grp" };
+static const char * const sdmmc2grp[] = { "sdmmc2grp" };
+static const char * const sdmmc3grp[] = { "sdmmc3grp" };
+static const char * const sdmmc4grp[] = { "sdmmc4grp" };
+static const char * const sdmmc5grp[] = { "sdmmc5grp" };
+static const char * const usb0_utmi_drvbusgrp[] = { "usb0_utmi_drvbusgrp" };
+static const char * const usb1_utmi_drvbusgrp[] = { "usb1_utmi_drvbusgrp" };
+static const char * const pulse_countgrp[] = { "pulse_countgrp" };
+static const char * const i2sgrp[] = { "i2sgrp" };
+static const char * const ac97grp[] = { "ac97grp" };
+static const char * const nandgrp[] = { "nandgrp" };
+static const char * const spi0grp[] = { "spi0grp" };
+static const char * const spi1grp[] = { "spi1grp" };
+static const char * const gpsgrp[] = { "gpsgrp" };
+
+#define SIRFSOC_PMX_FUNCTION(n, g, m)		\
+	{					\
+		.name = n,			\
+		.groups = g,			\
+		.num_groups = ARRAY_SIZE(g),	\
+		.padmux = &m,			\
+	}
+
+static const struct sirfsoc_pmx_func sirfsoc_pmx_functions[] = {
+	SIRFSOC_PMX_FUNCTION("lcd_16bits", lcd_16bitsgrp, lcd_16bits_padmux),
+	SIRFSOC_PMX_FUNCTION("lcd_18bits", lcd_18bitsgrp, lcd_18bits_padmux),
+	SIRFSOC_PMX_FUNCTION("lcd_24bits", lcd_24bitsgrp, lcd_24bits_padmux),
+	SIRFSOC_PMX_FUNCTION("lcdrom", lcdromgrp, lcdrom_padmux),
+	SIRFSOC_PMX_FUNCTION("uart0", uart0grp, uart0_padmux),
+	SIRFSOC_PMX_FUNCTION("uart1", uart1grp, uart1_padmux),
+	SIRFSOC_PMX_FUNCTION("uart2", uart2grp, uart2_padmux),
+	SIRFSOC_PMX_FUNCTION("uart2_nostreamctrl", uart2_nostreamctrlgrp, uart2_nostreamctrl_padmux),
+	SIRFSOC_PMX_FUNCTION("usp0", usp0grp, usp0_padmux),
+	SIRFSOC_PMX_FUNCTION("usp1", usp1grp, usp1_padmux),
+	SIRFSOC_PMX_FUNCTION("usp2", usp2grp, usp2_padmux),
+	SIRFSOC_PMX_FUNCTION("i2c0", i2c0grp, i2c0_padmux),
+	SIRFSOC_PMX_FUNCTION("i2c1", i2c1grp, i2c1_padmux),
+	SIRFSOC_PMX_FUNCTION("pwm0", pwm0grp, pwm0_padmux),
+	SIRFSOC_PMX_FUNCTION("pwm1", pwm1grp, pwm1_padmux),
+	SIRFSOC_PMX_FUNCTION("pwm2", pwm2grp, pwm2_padmux),
+	SIRFSOC_PMX_FUNCTION("pwm3", pwm3grp, pwm3_padmux),
+	SIRFSOC_PMX_FUNCTION("vip", vipgrp, vip_padmux),
+	SIRFSOC_PMX_FUNCTION("viprom", vipromgrp, viprom_padmux),
+	SIRFSOC_PMX_FUNCTION("warm_rst", warm_rstgrp, warm_rst_padmux),
+	SIRFSOC_PMX_FUNCTION("cko0", cko0grp, cko0_padmux),
+	SIRFSOC_PMX_FUNCTION("cko1", cko1grp, cko1_padmux),
+	SIRFSOC_PMX_FUNCTION("sdmmc0", sdmmc0grp, sdmmc0_padmux),
+	SIRFSOC_PMX_FUNCTION("sdmmc1", sdmmc1grp, sdmmc1_padmux),
+	SIRFSOC_PMX_FUNCTION("sdmmc2", sdmmc2grp, sdmmc2_padmux),
+	SIRFSOC_PMX_FUNCTION("sdmmc3", sdmmc3grp, sdmmc3_padmux),
+	SIRFSOC_PMX_FUNCTION("sdmmc4", sdmmc4grp, sdmmc4_padmux),
+	SIRFSOC_PMX_FUNCTION("sdmmc5", sdmmc5grp, sdmmc5_padmux),
+	SIRFSOC_PMX_FUNCTION("usb0_utmi_drvbus", usb0_utmi_drvbusgrp, usb0_utmi_drvbus_padmux),
+	SIRFSOC_PMX_FUNCTION("usb1_utmi_drvbus", usb1_utmi_drvbusgrp, usb1_utmi_drvbus_padmux),
+	SIRFSOC_PMX_FUNCTION("pulse_count", pulse_countgrp, pulse_count_padmux),
+	SIRFSOC_PMX_FUNCTION("i2s", i2sgrp, i2s_padmux),
+	SIRFSOC_PMX_FUNCTION("ac97", ac97grp, ac97_padmux),
+	SIRFSOC_PMX_FUNCTION("nand", nandgrp, nand_padmux),
+	SIRFSOC_PMX_FUNCTION("spi0", spi0grp, spi0_padmux),
+	SIRFSOC_PMX_FUNCTION("spi1", spi1grp, spi1_padmux),
+	SIRFSOC_PMX_FUNCTION("gps", gpsgrp, gps_padmux),
+};
+
+static void sirfsoc_pinmux_endisable(struct sirfsoc_pmx *spmx, unsigned selector,
+	bool enable)
+{
+	int i;
+	const struct sirfsoc_padmux *mux = sirfsoc_pmx_functions[selector].padmux;
+	const struct sirfsoc_muxmask *mask = mux->muxmask;
+
+	for (i = 0; i < mux->muxmask_counts; i++) {
+		u32 muxval;
+		muxval = readl(spmx->gpio_virtbase + SIRFSOC_GPIO_PAD_EN(mask[i].group));
+		if (enable)
+			muxval = muxval & ~mask[i].mask;
+		else
+			muxval = muxval | mask[i].mask;
+		writel(muxval, spmx->gpio_virtbase + SIRFSOC_GPIO_PAD_EN(mask[i].group));
+	}
+
+	if (mux->funcmask && enable) {
+		u32 func_en_val;
+		func_en_val =
+			readl(spmx->rsc_virtbase + SIRFSOC_RSC_PIN_MUX);
+		func_en_val =
+			(func_en_val & ~mux->funcmask) | (mux->
+				funcval);
+		writel(func_en_val, spmx->rsc_virtbase + SIRFSOC_RSC_PIN_MUX);
+	}
+}
+
+static int sirfsoc_pinmux_enable(struct pinctrl_dev *pmxdev, unsigned selector,
+	unsigned group)
+{
+	struct sirfsoc_pmx *spmx;
+
+	spmx = pinctrl_dev_get_drvdata(pmxdev);
+	sirfsoc_pinmux_endisable(spmx, selector, true);
+
+	return 0;
+}
+
+static void sirfsoc_pinmux_disable(struct pinctrl_dev *pmxdev, unsigned selector,
+	unsigned group)
+{
+	struct sirfsoc_pmx *spmx;
+
+	spmx = pinctrl_dev_get_drvdata(pmxdev);
+	sirfsoc_pinmux_endisable(spmx, selector, false);
+}
+
+static int sirfsoc_pinmux_list_funcs(struct pinctrl_dev *pmxdev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(sirfsoc_pmx_functions))
+		return -EINVAL;
+	return 0;
+}
+
+static const char *sirfsoc_pinmux_get_func_name(struct pinctrl_dev *pctldev,
+					  unsigned selector)
+{
+	return sirfsoc_pmx_functions[selector].name;
+}
+
+static int sirfsoc_pinmux_get_groups(struct pinctrl_dev *pctldev, unsigned selector,
+			       const char * const **groups,
+			       unsigned * const num_groups)
+{
+	*groups = sirfsoc_pmx_functions[selector].groups;
+	*num_groups = sirfsoc_pmx_functions[selector].num_groups;
+	return 0;
+}
+
+static int sirfsoc_pinmux_request_gpio(struct pinctrl_dev *pmxdev,
+	struct pinctrl_gpio_range *range, unsigned offset)
+{
+	struct sirfsoc_pmx *spmx;
+
+	int group = range->id;
+
+	u32 muxval;
+
+	spmx = pinctrl_dev_get_drvdata(pmxdev);
+
+	muxval = readl(spmx->gpio_virtbase + SIRFSOC_GPIO_PAD_EN(group));
+	muxval = muxval | (1 << offset);
+	writel(muxval, spmx->gpio_virtbase + SIRFSOC_GPIO_PAD_EN(group));
+
+	return 0;
+}
+
+static struct pinmux_ops sirfsoc_pinmux_ops = {
+	.list_functions = sirfsoc_pinmux_list_funcs,
+	.enable = sirfsoc_pinmux_enable,
+	.disable = sirfsoc_pinmux_disable,
+	.get_function_name = sirfsoc_pinmux_get_func_name,
+	.get_function_groups = sirfsoc_pinmux_get_groups,
+	.gpio_request_enable = sirfsoc_pinmux_request_gpio,
+};
+
+static struct pinctrl_desc sirfsoc_pinmux_desc = {
+	.name = DRIVER_NAME,
+	.pins = sirfsoc_pads,
+	.npins = ARRAY_SIZE(sirfsoc_pads),
+	.maxpin = SIRFSOC_NUM_PADS - 1,
+	.pctlops = &sirfsoc_pctrl_ops,
+	.pmxops = &sirfsoc_pinmux_ops,
+	.owner = THIS_MODULE,
+};
+
+/*
+ * Todo: bind irq_chip to every pinctrl_gpio_range
+ */
+static struct pinctrl_gpio_range sirfsoc_gpio_ranges[] = {
+	{
+		.name = "sirfsoc-gpio*",
+		.id = 0,
+		.base = 0,
+		.npins = 32,
+	}, {
+		.name = "sirfsoc-gpio*",
+		.id = 1,
+		.base = 32,
+		.npins = 32,
+	}, {
+		.name = "sirfsoc-gpio*",
+		.id = 2,
+		.base = 64,
+		.npins = 32,
+	}, {
+		.name = "sirfsoc-gpio*",
+		.id = 3,
+		.base = 96,
+		.npins = 19,
+	},
+};
+
+static void __iomem *sirfsoc_rsc_of_iomap(void)
+{
+	const struct of_device_id rsc_ids[]  = {
+		{ .compatible = "sirf,prima2-rsc" },
+		{}
+	};
+	struct device_node *np;
+
+	np = of_find_matching_node(NULL, rsc_ids);
+	if (!np)
+		panic("unable to find compatible rsc node in dtb\n");
+
+	return of_iomap(np, 0);
+}
+
+static int __devinit sirfsoc_pinmux_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct sirfsoc_pmx *spmx;
+	struct device_node *np = pdev->dev.of_node;
+	int i;
+
+	/* Create state holders etc for this driver */
+	spmx = devm_kzalloc(&pdev->dev, sizeof(*spmx), GFP_KERNEL);
+	if (!spmx)
+		return -ENOMEM;
+
+	spmx->dev = &pdev->dev;
+
+	platform_set_drvdata(pdev, spmx);
+
+	spmx->gpio_virtbase = of_iomap(np, 0);
+	if (!spmx->gpio_virtbase) {
+		ret = -ENOMEM;
+		dev_err(&pdev->dev, "can't map gpio registers\n");
+		goto out_no_gpio_remap;
+	}
+
+	spmx->rsc_virtbase = sirfsoc_rsc_of_iomap();
+	if (!spmx->rsc_virtbase) {
+		ret = -ENOMEM;
+		dev_err(&pdev->dev, "can't map rsc registers\n");
+		goto out_no_rsc_remap;
+	}
+
+	/* Now register the pin controller and all pins it handles */
+	spmx->pmx = pinctrl_register(&sirfsoc_pinmux_desc, &pdev->dev, spmx);
+	if (!spmx->pmx) {
+		dev_err(&pdev->dev, "could not register SIRFSOC pinmux driver\n");
+		ret = -EINVAL;
+		goto out_no_pmx;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(sirfsoc_gpio_ranges); i++)
+		pinctrl_add_gpio_range(spmx->pmx, &sirfsoc_gpio_ranges[i]);
+
+	dev_info(&pdev->dev, "initialized SIRFSOC pinmux driver\n");
+
+	return 0;
+
+out_no_pmx:
+	iounmap(spmx->rsc_virtbase);
+out_no_rsc_remap:
+	iounmap(spmx->gpio_virtbase);
+out_no_gpio_remap:
+	platform_set_drvdata(pdev, NULL);
+	devm_kfree(&pdev->dev, spmx);
+	return ret;
+}
+
+static const struct of_device_id pinmux_ids[]  = {
+	{ .compatible = "sirf,prima2-gpio-pinmux" },
+	{}
+};
+
+static struct platform_driver sirfsoc_pinmux_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.owner = THIS_MODULE,
+		.of_match_table = pinmux_ids,
+	},
+	.probe = sirfsoc_pinmux_probe,
+};
+
+static int __init sirfsoc_pinmux_init(void)
+{
+	return platform_driver_register(&sirfsoc_pinmux_driver);
+}
+arch_initcall(sirfsoc_pinmux_init);
+
+MODULE_AUTHOR("Rongjun Ying <rongjun.ying@csr.com>, "
+	"Barry Song <baohua.song@csr.com>");
+MODULE_DESCRIPTION("SIRFSOC pin control driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/pinctrl/pinmux-u300.c b/drivers/pinctrl/pinmux-u300.c
new file mode 100644
index 00000000000000..4858a64131f8e0
--- /dev/null
+++ b/drivers/pinctrl/pinmux-u300.c
@@ -0,0 +1,1135 @@
+/*
+ * Driver for the U300 pin controller
+ *
+ * Based on the original U300 padmux functions
+ * Copyright (C) 2009-2011 ST-Ericsson AB
+ * Author: Martin Persson <martin.persson@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * The DB3350 design and control registers are oriented around pads rather than
+ * pins, so we enumerate the pads we can mux rather than actual pins. The pads
+ * are connected to different pins in different packaging types, so it would
+ * be confusing.
+ */
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinmux.h>
+
+/*
+ * Register definitions for the U300 Padmux control registers in the
+ * system controller
+ */
+
+/* PAD MUX Control register 1 (LOW) 16bit (R/W) */
+#define U300_SYSCON_PMC1LR					0x007C
+#define U300_SYSCON_PMC1LR_MASK					0xFFFF
+#define U300_SYSCON_PMC1LR_CDI_MASK				0xC000
+#define U300_SYSCON_PMC1LR_CDI_CDI				0x0000
+#define U300_SYSCON_PMC1LR_CDI_EMIF				0x4000
+/* For BS335 */
+#define U300_SYSCON_PMC1LR_CDI_CDI2				0x8000
+#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO			0xC000
+/* For BS365 */
+#define U300_SYSCON_PMC1LR_CDI_GPIO				0x8000
+#define U300_SYSCON_PMC1LR_CDI_WCDMA				0xC000
+/* Common defs */
+#define U300_SYSCON_PMC1LR_PDI_MASK				0x3000
+#define U300_SYSCON_PMC1LR_PDI_PDI				0x0000
+#define U300_SYSCON_PMC1LR_PDI_EGG				0x1000
+#define U300_SYSCON_PMC1LR_PDI_WCDMA				0x3000
+#define U300_SYSCON_PMC1LR_MMCSD_MASK				0x0C00
+#define U300_SYSCON_PMC1LR_MMCSD_MMCSD				0x0000
+#define U300_SYSCON_PMC1LR_MMCSD_MSPRO				0x0400
+#define U300_SYSCON_PMC1LR_MMCSD_DSP				0x0800
+#define U300_SYSCON_PMC1LR_MMCSD_WCDMA				0x0C00
+#define U300_SYSCON_PMC1LR_ETM_MASK				0x0300
+#define U300_SYSCON_PMC1LR_ETM_ACC				0x0000
+#define U300_SYSCON_PMC1LR_ETM_APP				0x0100
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK			0x00C0
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC			0x0000
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF			0x0040
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM			0x0080
+#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB		0x00C0
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK			0x0030
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC			0x0000
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF			0x0010
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM			0x0020
+#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI			0x0030
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK			0x000C
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC			0x0000
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF			0x0004
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM			0x0008
+#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI			0x000C
+#define U300_SYSCON_PMC1LR_EMIF_1_MASK				0x0003
+#define U300_SYSCON_PMC1LR_EMIF_1_STATIC			0x0000
+#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0			0x0001
+#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1			0x0002
+#define U300_SYSCON_PMC1LR_EMIF_1				0x0003
+/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */
+#define U300_SYSCON_PMC1HR					0x007E
+#define U300_SYSCON_PMC1HR_MASK					0xFFFF
+#define U300_SYSCON_PMC1HR_MISC_2_MASK				0xC000
+#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO			0x0000
+#define U300_SYSCON_PMC1HR_MISC_2_MSPRO				0x4000
+#define U300_SYSCON_PMC1HR_MISC_2_DSP				0x8000
+#define U300_SYSCON_PMC1HR_MISC_2_AAIF				0xC000
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK			0x3000
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO			0x0000
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF			0x1000
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP			0x2000
+#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF			0x3000
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK			0x0C00
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO			0x0000
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC			0x0400
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP			0x0800
+#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF			0x0C00
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK			0x0300
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO		0x0000
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI			0x0100
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF			0x0300
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK			0x00C0
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO		0x0000
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI			0x0040
+#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF			0x00C0
+#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK			0x0030
+#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO			0x0000
+#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI			0x0010
+#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP			0x0020
+#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF			0x0030
+#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK			0x000C
+#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO			0x0000
+#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0			0x0004
+#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS			0x0008
+#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF			0x000C
+#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK			0x0003
+#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO			0x0000
+#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0			0x0001
+#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF			0x0003
+/* Padmux 2 control */
+#define U300_SYSCON_PMC2R					0x100
+#define U300_SYSCON_PMC2R_APP_MISC_0_MASK			0x00C0
+#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO			0x0000
+#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM			0x0040
+#define U300_SYSCON_PMC2R_APP_MISC_0_MMC			0x0080
+#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2			0x00C0
+#define U300_SYSCON_PMC2R_APP_MISC_1_MASK			0x0300
+#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO			0x0000
+#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM			0x0100
+#define U300_SYSCON_PMC2R_APP_MISC_1_MMC			0x0200
+#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2			0x0300
+#define U300_SYSCON_PMC2R_APP_MISC_2_MASK			0x0C00
+#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO			0x0000
+#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM			0x0400
+#define U300_SYSCON_PMC2R_APP_MISC_2_MMC			0x0800
+#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2			0x0C00
+#define U300_SYSCON_PMC2R_APP_MISC_3_MASK			0x3000
+#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO			0x0000
+#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM			0x1000
+#define U300_SYSCON_PMC2R_APP_MISC_3_MMC			0x2000
+#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2			0x3000
+#define U300_SYSCON_PMC2R_APP_MISC_4_MASK			0xC000
+#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO			0x0000
+#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM			0x4000
+#define U300_SYSCON_PMC2R_APP_MISC_4_MMC			0x8000
+#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO			0xC000
+/* TODO: More SYSCON registers missing */
+#define U300_SYSCON_PMC3R					0x10C
+#define U300_SYSCON_PMC3R_APP_MISC_11_MASK			0xC000
+#define U300_SYSCON_PMC3R_APP_MISC_11_SPI			0x4000
+#define U300_SYSCON_PMC3R_APP_MISC_10_MASK			0x3000
+#define U300_SYSCON_PMC3R_APP_MISC_10_SPI			0x1000
+/* TODO: Missing other configs */
+#define U300_SYSCON_PMC4R					0x168
+#define U300_SYSCON_PMC4R_APP_MISC_12_MASK			0x0003
+#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO			0x0000
+#define U300_SYSCON_PMC4R_APP_MISC_13_MASK			0x000C
+#define U300_SYSCON_PMC4R_APP_MISC_13_CDI			0x0000
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA			0x0004
+#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2			0x0008
+#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO			0x000C
+#define U300_SYSCON_PMC4R_APP_MISC_14_MASK			0x0030
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI			0x0000
+#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA			0x0010
+#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2			0x0020
+#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO			0x0030
+#define U300_SYSCON_PMC4R_APP_MISC_16_MASK			0x0300
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13		0x0000
+#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS		0x0100
+#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N	0x0200
+
+#define DRIVER_NAME "pinmux-u300"
+
+/*
+ * The DB3350 has 467 pads, I have enumerated the pads clockwise around the
+ * edges of the silicon, finger by finger. LTCORNER upper left is pad 0.
+ * Data taken from the PadRing chart, arranged like this:
+ *
+ *   0 ..... 104
+ * 466        105
+ *   .        .
+ *   .        .
+ * 358        224
+ *  357 .... 225
+ */
+#define U300_NUM_PADS 467
+
+/* Pad names for the pinmux subsystem */
+static const struct pinctrl_pin_desc u300_pads[] = {
+	/* Pads along the top edge of the chip */
+	PINCTRL_PIN(0, "P PAD VDD 28"),
+	PINCTRL_PIN(1, "P PAD GND 28"),
+	PINCTRL_PIN(2, "PO SIM RST N"),
+	PINCTRL_PIN(3, "VSSIO 25"),
+	PINCTRL_PIN(4, "VSSA ADDA ESDSUB"),
+	PINCTRL_PIN(5, "PWR VSSCOMMON"),
+	PINCTRL_PIN(6, "PI ADC I1 POS"),
+	PINCTRL_PIN(7, "PI ADC I1 NEG"),
+	PINCTRL_PIN(8, "PWR VSSAD0"),
+	PINCTRL_PIN(9, "PWR VCCAD0"),
+	PINCTRL_PIN(10, "PI ADC Q1 NEG"),
+	PINCTRL_PIN(11, "PI ADC Q1 POS"),
+	PINCTRL_PIN(12, "PWR VDDAD"),
+	PINCTRL_PIN(13, "PWR GNDAD"),
+	PINCTRL_PIN(14, "PI ADC I2 POS"),
+	PINCTRL_PIN(15, "PI ADC I2 NEG"),
+	PINCTRL_PIN(16, "PWR VSSAD1"),
+	PINCTRL_PIN(17, "PWR VCCAD1"),
+	PINCTRL_PIN(18, "PI ADC Q2 NEG"),
+	PINCTRL_PIN(19, "PI ADC Q2 POS"),
+	PINCTRL_PIN(20, "VSSA ADDA ESDSUB"),
+	PINCTRL_PIN(21, "PWR VCCGPAD"),
+	PINCTRL_PIN(22, "PI TX POW"),
+	PINCTRL_PIN(23, "PWR VSSGPAD"),
+	PINCTRL_PIN(24, "PO DAC I POS"),
+	PINCTRL_PIN(25, "PO DAC I NEG"),
+	PINCTRL_PIN(26, "PO DAC Q POS"),
+	PINCTRL_PIN(27, "PO DAC Q NEG"),
+	PINCTRL_PIN(28, "PWR VSSDA"),
+	PINCTRL_PIN(29, "PWR VCCDA"),
+	PINCTRL_PIN(30, "VSSA ADDA ESDSUB"),
+	PINCTRL_PIN(31, "P PAD VDDIO 11"),
+	PINCTRL_PIN(32, "PI PLL 26 FILTVDD"),
+	PINCTRL_PIN(33, "PI PLL 26 VCONT"),
+	PINCTRL_PIN(34, "PWR AGNDPLL2V5 32 13"),
+	PINCTRL_PIN(35, "PWR AVDDPLL2V5 32 13"),
+	PINCTRL_PIN(36, "VDDA PLL ESD"),
+	PINCTRL_PIN(37, "VSSA PLL ESD"),
+	PINCTRL_PIN(38, "VSS PLL"),
+	PINCTRL_PIN(39, "VDDC PLL"),
+	PINCTRL_PIN(40, "PWR AGNDPLL2V5 26 60"),
+	PINCTRL_PIN(41, "PWR AVDDPLL2V5 26 60"),
+	PINCTRL_PIN(42, "PWR AVDDPLL2V5 26 208"),
+	PINCTRL_PIN(43, "PWR AGNDPLL2V5 26 208"),
+	PINCTRL_PIN(44, "PWR AVDDPLL2V5 13 208"),
+	PINCTRL_PIN(45, "PWR AGNDPLL2V5 13 208"),
+	PINCTRL_PIN(46, "P PAD VSSIO 11"),
+	PINCTRL_PIN(47, "P PAD VSSIO 12"),
+	PINCTRL_PIN(48, "PI POW RST N"),
+	PINCTRL_PIN(49, "VDDC IO"),
+	PINCTRL_PIN(50, "P PAD VDDIO 16"),
+	PINCTRL_PIN(51, "PO RF WCDMA EN 4"),
+	PINCTRL_PIN(52, "PO RF WCDMA EN 3"),
+	PINCTRL_PIN(53, "PO RF WCDMA EN 2"),
+	PINCTRL_PIN(54, "PO RF WCDMA EN 1"),
+	PINCTRL_PIN(55, "PO RF WCDMA EN 0"),
+	PINCTRL_PIN(56, "PO GSM PA ENABLE"),
+	PINCTRL_PIN(57, "PO RF DATA STRB"),
+	PINCTRL_PIN(58, "PO RF DATA2"),
+	PINCTRL_PIN(59, "PIO RF DATA1"),
+	PINCTRL_PIN(60, "PIO RF DATA0"),
+	PINCTRL_PIN(61, "P PAD VDD 11"),
+	PINCTRL_PIN(62, "P PAD GND 11"),
+	PINCTRL_PIN(63, "P PAD VSSIO 16"),
+	PINCTRL_PIN(64, "P PAD VDDIO 18"),
+	PINCTRL_PIN(65, "PO RF CTRL STRB2"),
+	PINCTRL_PIN(66, "PO RF CTRL STRB1"),
+	PINCTRL_PIN(67, "PO RF CTRL STRB0"),
+	PINCTRL_PIN(68, "PIO RF CTRL DATA"),
+	PINCTRL_PIN(69, "PO RF CTRL CLK"),
+	PINCTRL_PIN(70, "PO TX ADC STRB"),
+	PINCTRL_PIN(71, "PO ANT SW 2"),
+	PINCTRL_PIN(72, "PO ANT SW 3"),
+	PINCTRL_PIN(73, "PO ANT SW 0"),
+	PINCTRL_PIN(74, "PO ANT SW 1"),
+	PINCTRL_PIN(75, "PO M CLKRQ"),
+	PINCTRL_PIN(76, "PI M CLK"),
+	PINCTRL_PIN(77, "PI RTC CLK"),
+	PINCTRL_PIN(78, "P PAD VDD 8"),
+	PINCTRL_PIN(79, "P PAD GND 8"),
+	PINCTRL_PIN(80, "P PAD VSSIO 13"),
+	PINCTRL_PIN(81, "P PAD VDDIO 13"),
+	PINCTRL_PIN(82, "PO SYS 1 CLK"),
+	PINCTRL_PIN(83, "PO SYS 2 CLK"),
+	PINCTRL_PIN(84, "PO SYS 0 CLK"),
+	PINCTRL_PIN(85, "PI SYS 0 CLKRQ"),
+	PINCTRL_PIN(86, "PO PWR MNGT CTRL 1"),
+	PINCTRL_PIN(87, "PO PWR MNGT CTRL 0"),
+	PINCTRL_PIN(88, "PO RESOUT2 RST N"),
+	PINCTRL_PIN(89, "PO RESOUT1 RST N"),
+	PINCTRL_PIN(90, "PO RESOUT0 RST N"),
+	PINCTRL_PIN(91, "PI SERVICE N"),
+	PINCTRL_PIN(92, "P PAD VDD 29"),
+	PINCTRL_PIN(93, "P PAD GND 29"),
+	PINCTRL_PIN(94, "P PAD VSSIO 8"),
+	PINCTRL_PIN(95, "P PAD VDDIO 8"),
+	PINCTRL_PIN(96, "PI EXT IRQ1 N"),
+	PINCTRL_PIN(97, "PI EXT IRQ0 N"),
+	PINCTRL_PIN(98, "PIO DC ON"),
+	PINCTRL_PIN(99, "PIO ACC APP I2C DATA"),
+	PINCTRL_PIN(100, "PIO ACC APP I2C CLK"),
+	PINCTRL_PIN(101, "P PAD VDD 12"),
+	PINCTRL_PIN(102, "P PAD GND 12"),
+	PINCTRL_PIN(103, "P PAD VSSIO 14"),
+	PINCTRL_PIN(104, "P PAD VDDIO 14"),
+	/* Pads along the right edge of the chip */
+	PINCTRL_PIN(105, "PIO APP I2C1 DATA"),
+	PINCTRL_PIN(106, "PIO APP I2C1 CLK"),
+	PINCTRL_PIN(107, "PO KEY OUT0"),
+	PINCTRL_PIN(108, "PO KEY OUT1"),
+	PINCTRL_PIN(109, "PO KEY OUT2"),
+	PINCTRL_PIN(110, "PO KEY OUT3"),
+	PINCTRL_PIN(111, "PO KEY OUT4"),
+	PINCTRL_PIN(112, "PI KEY IN0"),
+	PINCTRL_PIN(113, "PI KEY IN1"),
+	PINCTRL_PIN(114, "PI KEY IN2"),
+	PINCTRL_PIN(115, "P PAD VDDIO 15"),
+	PINCTRL_PIN(116, "P PAD VSSIO 15"),
+	PINCTRL_PIN(117, "P PAD GND 13"),
+	PINCTRL_PIN(118, "P PAD VDD 13"),
+	PINCTRL_PIN(119, "PI KEY IN3"),
+	PINCTRL_PIN(120, "PI KEY IN4"),
+	PINCTRL_PIN(121, "PI KEY IN5"),
+	PINCTRL_PIN(122, "PIO APP PCM I2S1 DATA B"),
+	PINCTRL_PIN(123, "PIO APP PCM I2S1 DATA A"),
+	PINCTRL_PIN(124, "PIO APP PCM I2S1 WS"),
+	PINCTRL_PIN(125, "PIO APP PCM I2S1 CLK"),
+	PINCTRL_PIN(126, "PIO APP PCM I2S0 DATA B"),
+	PINCTRL_PIN(127, "PIO APP PCM I2S0 DATA A"),
+	PINCTRL_PIN(128, "PIO APP PCM I2S0 WS"),
+	PINCTRL_PIN(129, "PIO APP PCM I2S0 CLK"),
+	PINCTRL_PIN(130, "P PAD VDD 17"),
+	PINCTRL_PIN(131, "P PAD GND 17"),
+	PINCTRL_PIN(132, "P PAD VSSIO 19"),
+	PINCTRL_PIN(133, "P PAD VDDIO 19"),
+	PINCTRL_PIN(134, "UART0 RTS"),
+	PINCTRL_PIN(135, "UART0 CTS"),
+	PINCTRL_PIN(136, "UART0 TX"),
+	PINCTRL_PIN(137, "UART0 RX"),
+	PINCTRL_PIN(138, "PIO ACC SPI DO"),
+	PINCTRL_PIN(139, "PIO ACC SPI DI"),
+	PINCTRL_PIN(140, "PIO ACC SPI CS0 N"),
+	PINCTRL_PIN(141, "PIO ACC SPI CS1 N"),
+	PINCTRL_PIN(142, "PIO ACC SPI CS2 N"),
+	PINCTRL_PIN(143, "PIO ACC SPI CLK"),
+	PINCTRL_PIN(144, "PO PDI EXT RST N"),
+	PINCTRL_PIN(145, "P PAD VDDIO 22"),
+	PINCTRL_PIN(146, "P PAD VSSIO 22"),
+	PINCTRL_PIN(147, "P PAD GND 18"),
+	PINCTRL_PIN(148, "P PAD VDD 18"),
+	PINCTRL_PIN(149, "PIO PDI C0"),
+	PINCTRL_PIN(150, "PIO PDI C1"),
+	PINCTRL_PIN(151, "PIO PDI C2"),
+	PINCTRL_PIN(152, "PIO PDI C3"),
+	PINCTRL_PIN(153, "PIO PDI C4"),
+	PINCTRL_PIN(154, "PIO PDI C5"),
+	PINCTRL_PIN(155, "PIO PDI D0"),
+	PINCTRL_PIN(156, "PIO PDI D1"),
+	PINCTRL_PIN(157, "PIO PDI D2"),
+	PINCTRL_PIN(158, "PIO PDI D3"),
+	PINCTRL_PIN(159, "P PAD VDDIO 21"),
+	PINCTRL_PIN(160, "P PAD VSSIO 21"),
+	PINCTRL_PIN(161, "PIO PDI D4"),
+	PINCTRL_PIN(162, "PIO PDI D5"),
+	PINCTRL_PIN(163, "PIO PDI D6"),
+	PINCTRL_PIN(164, "PIO PDI D7"),
+	PINCTRL_PIN(165, "PIO MS INS"),
+	PINCTRL_PIN(166, "MMC DATA DIR LS"),
+	PINCTRL_PIN(167, "MMC DATA 3"),
+	PINCTRL_PIN(168, "MMC DATA 2"),
+	PINCTRL_PIN(169, "MMC DATA 1"),
+	PINCTRL_PIN(170, "MMC DATA 0"),
+	PINCTRL_PIN(171, "MMC CMD DIR LS"),
+	PINCTRL_PIN(172, "P PAD VDD 27"),
+	PINCTRL_PIN(173, "P PAD GND 27"),
+	PINCTRL_PIN(174, "P PAD VSSIO 20"),
+	PINCTRL_PIN(175, "P PAD VDDIO 20"),
+	PINCTRL_PIN(176, "MMC CMD"),
+	PINCTRL_PIN(177, "MMC CLK"),
+	PINCTRL_PIN(178, "PIO APP GPIO 14"),
+	PINCTRL_PIN(179, "PIO APP GPIO 13"),
+	PINCTRL_PIN(180, "PIO APP GPIO 11"),
+	PINCTRL_PIN(181, "PIO APP GPIO 25"),
+	PINCTRL_PIN(182, "PIO APP GPIO 24"),
+	PINCTRL_PIN(183, "PIO APP GPIO 23"),
+	PINCTRL_PIN(184, "PIO APP GPIO 22"),
+	PINCTRL_PIN(185, "PIO APP GPIO 21"),
+	PINCTRL_PIN(186, "PIO APP GPIO 20"),
+	PINCTRL_PIN(187, "P PAD VDD 19"),
+	PINCTRL_PIN(188, "P PAD GND 19"),
+	PINCTRL_PIN(189, "P PAD VSSIO 23"),
+	PINCTRL_PIN(190, "P PAD VDDIO 23"),
+	PINCTRL_PIN(191, "PIO APP GPIO 19"),
+	PINCTRL_PIN(192, "PIO APP GPIO 18"),
+	PINCTRL_PIN(193, "PIO APP GPIO 17"),
+	PINCTRL_PIN(194, "PIO APP GPIO 16"),
+	PINCTRL_PIN(195, "PI CI D1"),
+	PINCTRL_PIN(196, "PI CI D0"),
+	PINCTRL_PIN(197, "PI CI HSYNC"),
+	PINCTRL_PIN(198, "PI CI VSYNC"),
+	PINCTRL_PIN(199, "PI CI EXT CLK"),
+	PINCTRL_PIN(200, "PO CI EXT RST N"),
+	PINCTRL_PIN(201, "P PAD VSSIO 43"),
+	PINCTRL_PIN(202, "P PAD VDDIO 43"),
+	PINCTRL_PIN(203, "PI CI D6"),
+	PINCTRL_PIN(204, "PI CI D7"),
+	PINCTRL_PIN(205, "PI CI D2"),
+	PINCTRL_PIN(206, "PI CI D3"),
+	PINCTRL_PIN(207, "PI CI D4"),
+	PINCTRL_PIN(208, "PI CI D5"),
+	PINCTRL_PIN(209, "PI CI D8"),
+	PINCTRL_PIN(210, "PI CI D9"),
+	PINCTRL_PIN(211, "P PAD VDD 20"),
+	PINCTRL_PIN(212, "P PAD GND 20"),
+	PINCTRL_PIN(213, "P PAD VSSIO 24"),
+	PINCTRL_PIN(214, "P PAD VDDIO 24"),
+	PINCTRL_PIN(215, "P PAD VDDIO 26"),
+	PINCTRL_PIN(216, "PO EMIF 1 A26"),
+	PINCTRL_PIN(217, "PO EMIF 1 A25"),
+	PINCTRL_PIN(218, "P PAD VSSIO 26"),
+	PINCTRL_PIN(219, "PO EMIF 1 A24"),
+	PINCTRL_PIN(220, "PO EMIF 1 A23"),
+	/* Pads along the bottom edge of the chip */
+	PINCTRL_PIN(221, "PO EMIF 1 A22"),
+	PINCTRL_PIN(222, "PO EMIF 1 A21"),
+	PINCTRL_PIN(223, "P PAD VDD 21"),
+	PINCTRL_PIN(224, "P PAD GND 21"),
+	PINCTRL_PIN(225, "P PAD VSSIO 27"),
+	PINCTRL_PIN(226, "P PAD VDDIO 27"),
+	PINCTRL_PIN(227, "PO EMIF 1 A20"),
+	PINCTRL_PIN(228, "PO EMIF 1 A19"),
+	PINCTRL_PIN(229, "PO EMIF 1 A18"),
+	PINCTRL_PIN(230, "PO EMIF 1 A17"),
+	PINCTRL_PIN(231, "P PAD VDDIO 28"),
+	PINCTRL_PIN(232, "P PAD VSSIO 28"),
+	PINCTRL_PIN(233, "PO EMIF 1 A16"),
+	PINCTRL_PIN(234, "PIO EMIF 1 D15"),
+	PINCTRL_PIN(235, "PO EMIF 1 A15"),
+	PINCTRL_PIN(236, "PIO EMIF 1 D14"),
+	PINCTRL_PIN(237, "P PAD VDD 22"),
+	PINCTRL_PIN(238, "P PAD GND 22"),
+	PINCTRL_PIN(239, "P PAD VSSIO 29"),
+	PINCTRL_PIN(240, "P PAD VDDIO 29"),
+	PINCTRL_PIN(241, "PO EMIF 1 A14"),
+	PINCTRL_PIN(242, "PIO EMIF 1 D13"),
+	PINCTRL_PIN(243, "PO EMIF 1 A13"),
+	PINCTRL_PIN(244, "PIO EMIF 1 D12"),
+	PINCTRL_PIN(245, "P PAD VSSIO 30"),
+	PINCTRL_PIN(246, "P PAD VDDIO 30"),
+	PINCTRL_PIN(247, "PO EMIF 1 A12"),
+	PINCTRL_PIN(248, "PIO EMIF 1 D11"),
+	PINCTRL_PIN(249, "PO EMIF 1 A11"),
+	PINCTRL_PIN(250, "PIO EMIF 1 D10"),
+	PINCTRL_PIN(251, "P PAD VSSIO 31"),
+	PINCTRL_PIN(252, "P PAD VDDIO 31"),
+	PINCTRL_PIN(253, "PO EMIF 1 A10"),
+	PINCTRL_PIN(254, "PIO EMIF 1 D09"),
+	PINCTRL_PIN(255, "PO EMIF 1 A09"),
+	PINCTRL_PIN(256, "P PAD VDDIO 32"),
+	PINCTRL_PIN(257, "P PAD VSSIO 32"),
+	PINCTRL_PIN(258, "P PAD GND 24"),
+	PINCTRL_PIN(259, "P PAD VDD 24"),
+	PINCTRL_PIN(260, "PIO EMIF 1 D08"),
+	PINCTRL_PIN(261, "PO EMIF 1 A08"),
+	PINCTRL_PIN(262, "PIO EMIF 1 D07"),
+	PINCTRL_PIN(263, "PO EMIF 1 A07"),
+	PINCTRL_PIN(264, "P PAD VDDIO 33"),
+	PINCTRL_PIN(265, "P PAD VSSIO 33"),
+	PINCTRL_PIN(266, "PIO EMIF 1 D06"),
+	PINCTRL_PIN(267, "PO EMIF 1 A06"),
+	PINCTRL_PIN(268, "PIO EMIF 1 D05"),
+	PINCTRL_PIN(269, "PO EMIF 1 A05"),
+	PINCTRL_PIN(270, "P PAD VDDIO 34"),
+	PINCTRL_PIN(271, "P PAD VSSIO 34"),
+	PINCTRL_PIN(272, "PIO EMIF 1 D04"),
+	PINCTRL_PIN(273, "PO EMIF 1 A04"),
+	PINCTRL_PIN(274, "PIO EMIF 1 D03"),
+	PINCTRL_PIN(275, "PO EMIF 1 A03"),
+	PINCTRL_PIN(276, "P PAD VDDIO 35"),
+	PINCTRL_PIN(277, "P PAD VSSIO 35"),
+	PINCTRL_PIN(278, "P PAD GND 23"),
+	PINCTRL_PIN(279, "P PAD VDD 23"),
+	PINCTRL_PIN(280, "PIO EMIF 1 D02"),
+	PINCTRL_PIN(281, "PO EMIF 1 A02"),
+	PINCTRL_PIN(282, "PIO EMIF 1 D01"),
+	PINCTRL_PIN(283, "PO EMIF 1 A01"),
+	PINCTRL_PIN(284, "P PAD VDDIO 36"),
+	PINCTRL_PIN(285, "P PAD VSSIO 36"),
+	PINCTRL_PIN(286, "PIO EMIF 1 D00"),
+	PINCTRL_PIN(287, "PO EMIF 1 BE1 N"),
+	PINCTRL_PIN(288, "PO EMIF 1 BE0 N"),
+	PINCTRL_PIN(289, "PO EMIF 1 ADV N"),
+	PINCTRL_PIN(290, "P PAD VDDIO 37"),
+	PINCTRL_PIN(291, "P PAD VSSIO 37"),
+	PINCTRL_PIN(292, "PO EMIF 1 SD CKE0"),
+	PINCTRL_PIN(293, "PO EMIF 1 OE N"),
+	PINCTRL_PIN(294, "PO EMIF 1 WE N"),
+	PINCTRL_PIN(295, "P PAD VDDIO 38"),
+	PINCTRL_PIN(296, "P PAD VSSIO 38"),
+	PINCTRL_PIN(297, "PO EMIF 1 CLK"),
+	PINCTRL_PIN(298, "PIO EMIF 1 SD CLK"),
+	PINCTRL_PIN(299, "P PAD VSSIO 45 (not bonded)"),
+	PINCTRL_PIN(300, "P PAD VDDIO 42"),
+	PINCTRL_PIN(301, "P PAD VSSIO 42"),
+	PINCTRL_PIN(302, "P PAD GND 31"),
+	PINCTRL_PIN(303, "P PAD VDD 31"),
+	PINCTRL_PIN(304, "PI EMIF 1 RET CLK"),
+	PINCTRL_PIN(305, "PI EMIF 1 WAIT N"),
+	PINCTRL_PIN(306, "PI EMIF 1 NFIF READY"),
+	PINCTRL_PIN(307, "PO EMIF 1 SD CKE1"),
+	PINCTRL_PIN(308, "PO EMIF 1 CS3 N"),
+	PINCTRL_PIN(309, "P PAD VDD 25"),
+	PINCTRL_PIN(310, "P PAD GND 25"),
+	PINCTRL_PIN(311, "P PAD VSSIO 39"),
+	PINCTRL_PIN(312, "P PAD VDDIO 39"),
+	PINCTRL_PIN(313, "PO EMIF 1 CS2 N"),
+	PINCTRL_PIN(314, "PO EMIF 1 CS1 N"),
+	PINCTRL_PIN(315, "PO EMIF 1 CS0 N"),
+	PINCTRL_PIN(316, "PO ETM TRACE PKT0"),
+	PINCTRL_PIN(317, "PO ETM TRACE PKT1"),
+	PINCTRL_PIN(318, "PO ETM TRACE PKT2"),
+	PINCTRL_PIN(319, "P PAD VDD 30"),
+	PINCTRL_PIN(320, "P PAD GND 30"),
+	PINCTRL_PIN(321, "P PAD VSSIO 44"),
+	PINCTRL_PIN(322, "P PAD VDDIO 44"),
+	PINCTRL_PIN(323, "PO ETM TRACE PKT3"),
+	PINCTRL_PIN(324, "PO ETM TRACE PKT4"),
+	PINCTRL_PIN(325, "PO ETM TRACE PKT5"),
+	PINCTRL_PIN(326, "PO ETM TRACE PKT6"),
+	PINCTRL_PIN(327, "PO ETM TRACE PKT7"),
+	PINCTRL_PIN(328, "PO ETM PIPE STAT0"),
+	PINCTRL_PIN(329, "P PAD VDD 26"),
+	PINCTRL_PIN(330, "P PAD GND 26"),
+	PINCTRL_PIN(331, "P PAD VSSIO 40"),
+	PINCTRL_PIN(332, "P PAD VDDIO 40"),
+	PINCTRL_PIN(333, "PO ETM PIPE STAT1"),
+	PINCTRL_PIN(334, "PO ETM PIPE STAT2"),
+	PINCTRL_PIN(335, "PO ETM TRACE CLK"),
+	PINCTRL_PIN(336, "PO ETM TRACE SYNC"),
+	PINCTRL_PIN(337, "PIO ACC GPIO 33"),
+	PINCTRL_PIN(338, "PIO ACC GPIO 32"),
+	PINCTRL_PIN(339, "PIO ACC GPIO 30"),
+	PINCTRL_PIN(340, "PIO ACC GPIO 29"),
+	PINCTRL_PIN(341, "P PAD VDDIO 17"),
+	PINCTRL_PIN(342, "P PAD VSSIO 17"),
+	PINCTRL_PIN(343, "P PAD GND 15"),
+	PINCTRL_PIN(344, "P PAD VDD 15"),
+	PINCTRL_PIN(345, "PIO ACC GPIO 28"),
+	PINCTRL_PIN(346, "PIO ACC GPIO 27"),
+	PINCTRL_PIN(347, "PIO ACC GPIO 16"),
+	PINCTRL_PIN(348, "PI TAP TMS"),
+	PINCTRL_PIN(349, "PI TAP TDI"),
+	PINCTRL_PIN(350, "PO TAP TDO"),
+	PINCTRL_PIN(351, "PI TAP RST N"),
+	/* Pads along the left edge of the chip */
+	PINCTRL_PIN(352, "PI EMU MODE 0"),
+	PINCTRL_PIN(353, "PO TAP RET CLK"),
+	PINCTRL_PIN(354, "PI TAP CLK"),
+	PINCTRL_PIN(355, "PO EMIF 0 SD CS N"),
+	PINCTRL_PIN(356, "PO EMIF 0 SD CAS N"),
+	PINCTRL_PIN(357, "PO EMIF 0 SD WE N"),
+	PINCTRL_PIN(358, "P PAD VDDIO 1"),
+	PINCTRL_PIN(359, "P PAD VSSIO 1"),
+	PINCTRL_PIN(360, "P PAD GND 1"),
+	PINCTRL_PIN(361, "P PAD VDD 1"),
+	PINCTRL_PIN(362, "PO EMIF 0 SD CKE"),
+	PINCTRL_PIN(363, "PO EMIF 0 SD DQML"),
+	PINCTRL_PIN(364, "PO EMIF 0 SD DQMU"),
+	PINCTRL_PIN(365, "PO EMIF 0 SD RAS N"),
+	PINCTRL_PIN(366, "PIO EMIF 0 D15"),
+	PINCTRL_PIN(367, "PO EMIF 0 A15"),
+	PINCTRL_PIN(368, "PIO EMIF 0 D14"),
+	PINCTRL_PIN(369, "PO EMIF 0 A14"),
+	PINCTRL_PIN(370, "PIO EMIF 0 D13"),
+	PINCTRL_PIN(371, "PO EMIF 0 A13"),
+	PINCTRL_PIN(372, "P PAD VDDIO 2"),
+	PINCTRL_PIN(373, "P PAD VSSIO 2"),
+	PINCTRL_PIN(374, "P PAD GND 2"),
+	PINCTRL_PIN(375, "P PAD VDD 2"),
+	PINCTRL_PIN(376, "PIO EMIF 0 D12"),
+	PINCTRL_PIN(377, "PO EMIF 0 A12"),
+	PINCTRL_PIN(378, "PIO EMIF 0 D11"),
+	PINCTRL_PIN(379, "PO EMIF 0 A11"),
+	PINCTRL_PIN(380, "PIO EMIF 0 D10"),
+	PINCTRL_PIN(381, "PO EMIF 0 A10"),
+	PINCTRL_PIN(382, "PIO EMIF 0 D09"),
+	PINCTRL_PIN(383, "PO EMIF 0 A09"),
+	PINCTRL_PIN(384, "PIO EMIF 0 D08"),
+	PINCTRL_PIN(385, "PO EMIF 0 A08"),
+	PINCTRL_PIN(386, "PIO EMIF 0 D07"),
+	PINCTRL_PIN(387, "PO EMIF 0 A07"),
+	PINCTRL_PIN(388, "P PAD VDDIO 3"),
+	PINCTRL_PIN(389, "P PAD VSSIO 3"),
+	PINCTRL_PIN(390, "P PAD GND 3"),
+	PINCTRL_PIN(391, "P PAD VDD 3"),
+	PINCTRL_PIN(392, "PO EFUSE RDOUT1"),
+	PINCTRL_PIN(393, "PIO EMIF 0 D06"),
+	PINCTRL_PIN(394, "PO EMIF 0 A06"),
+	PINCTRL_PIN(395, "PIO EMIF 0 D05"),
+	PINCTRL_PIN(396, "PO EMIF 0 A05"),
+	PINCTRL_PIN(397, "PIO EMIF 0 D04"),
+	PINCTRL_PIN(398, "PO EMIF 0 A04"),
+	PINCTRL_PIN(399, "A PADS/A VDDCO1v82v5 GND 80U SF LIN VDDCO AF"),
+	PINCTRL_PIN(400, "PWR VDDCO AF"),
+	PINCTRL_PIN(401, "PWR EFUSE HV1"),
+	PINCTRL_PIN(402, "P PAD VSSIO 4"),
+	PINCTRL_PIN(403, "P PAD VDDIO 4"),
+	PINCTRL_PIN(404, "P PAD GND 4"),
+	PINCTRL_PIN(405, "P PAD VDD 4"),
+	PINCTRL_PIN(406, "PIO EMIF 0 D03"),
+	PINCTRL_PIN(407, "PO EMIF 0 A03"),
+	PINCTRL_PIN(408, "PWR EFUSE HV2"),
+	PINCTRL_PIN(409, "PWR EFUSE HV3"),
+	PINCTRL_PIN(410, "PIO EMIF 0 D02"),
+	PINCTRL_PIN(411, "PO EMIF 0 A02"),
+	PINCTRL_PIN(412, "PIO EMIF 0 D01"),
+	PINCTRL_PIN(413, "P PAD VDDIO 5"),
+	PINCTRL_PIN(414, "P PAD VSSIO 5"),
+	PINCTRL_PIN(415, "P PAD GND 5"),
+	PINCTRL_PIN(416, "P PAD VDD 5"),
+	PINCTRL_PIN(417, "PO EMIF 0 A01"),
+	PINCTRL_PIN(418, "PIO EMIF 0 D00"),
+	PINCTRL_PIN(419, "IF 0 SD CLK"),
+	PINCTRL_PIN(420, "APP SPI CLK"),
+	PINCTRL_PIN(421, "APP SPI DO"),
+	PINCTRL_PIN(422, "APP SPI DI"),
+	PINCTRL_PIN(423, "APP SPI CS0"),
+	PINCTRL_PIN(424, "APP SPI CS1"),
+	PINCTRL_PIN(425, "APP SPI CS2"),
+	PINCTRL_PIN(426, "PIO APP GPIO 10"),
+	PINCTRL_PIN(427, "P PAD VDDIO 41"),
+	PINCTRL_PIN(428, "P PAD VSSIO 41"),
+	PINCTRL_PIN(429, "P PAD GND 6"),
+	PINCTRL_PIN(430, "P PAD VDD 6"),
+	PINCTRL_PIN(431, "PIO ACC SDIO0 CMD"),
+	PINCTRL_PIN(432, "PIO ACC SDIO0 CK"),
+	PINCTRL_PIN(433, "PIO ACC SDIO0 D3"),
+	PINCTRL_PIN(434, "PIO ACC SDIO0 D2"),
+	PINCTRL_PIN(435, "PIO ACC SDIO0 D1"),
+	PINCTRL_PIN(436, "PIO ACC SDIO0 D0"),
+	PINCTRL_PIN(437, "PIO USB PU"),
+	PINCTRL_PIN(438, "PIO USB SP"),
+	PINCTRL_PIN(439, "PIO USB DAT VP"),
+	PINCTRL_PIN(440, "PIO USB SE0 VM"),
+	PINCTRL_PIN(441, "PIO USB OE"),
+	PINCTRL_PIN(442, "PIO USB SUSP"),
+	PINCTRL_PIN(443, "P PAD VSSIO 6"),
+	PINCTRL_PIN(444, "P PAD VDDIO 6"),
+	PINCTRL_PIN(445, "PIO USB PUEN"),
+	PINCTRL_PIN(446, "PIO ACC UART0 RX"),
+	PINCTRL_PIN(447, "PIO ACC UART0 TX"),
+	PINCTRL_PIN(448, "PIO ACC UART0 CTS"),
+	PINCTRL_PIN(449, "PIO ACC UART0 RTS"),
+	PINCTRL_PIN(450, "PIO ACC UART3 RX"),
+	PINCTRL_PIN(451, "PIO ACC UART3 TX"),
+	PINCTRL_PIN(452, "PIO ACC UART3 CTS"),
+	PINCTRL_PIN(453, "PIO ACC UART3 RTS"),
+	PINCTRL_PIN(454, "PIO ACC IRDA TX"),
+	PINCTRL_PIN(455, "P PAD VDDIO 7"),
+	PINCTRL_PIN(456, "P PAD VSSIO 7"),
+	PINCTRL_PIN(457, "P PAD GND 7"),
+	PINCTRL_PIN(458, "P PAD VDD 7"),
+	PINCTRL_PIN(459, "PIO ACC IRDA RX"),
+	PINCTRL_PIN(460, "PIO ACC PCM I2S CLK"),
+	PINCTRL_PIN(461, "PIO ACC PCM I2S WS"),
+	PINCTRL_PIN(462, "PIO ACC PCM I2S DATA A"),
+	PINCTRL_PIN(463, "PIO ACC PCM I2S DATA B"),
+	PINCTRL_PIN(464, "PO SIM CLK"),
+	PINCTRL_PIN(465, "PIO ACC IRDA SD"),
+	PINCTRL_PIN(466, "PIO SIM DATA"),
+};
+
+/**
+ * @dev: a pointer back to containing device
+ * @virtbase: the offset to the controller in virtual memory
+ */
+struct u300_pmx {
+	struct device *dev;
+	struct pinctrl_dev *pctl;
+	u32 phybase;
+	u32 physize;
+	void __iomem *virtbase;
+};
+
+/**
+ * u300_pmx_registers - the array of registers read/written for each pinmux
+ * shunt setting
+ */
+const u32 u300_pmx_registers[] = {
+	U300_SYSCON_PMC1LR,
+	U300_SYSCON_PMC1HR,
+	U300_SYSCON_PMC2R,
+	U300_SYSCON_PMC3R,
+	U300_SYSCON_PMC4R,
+};
+
+/**
+ * struct u300_pin_group - describes a U300 pin group
+ * @name: the name of this specific pin group
+ * @pins: an array of discrete physical pins used in this group, taken
+ *	from the driver-local pin enumeration space
+ * @num_pins: the number of pins in this group array, i.e. the number of
+ *	elements in .pins so we can iterate over that array
+ */
+struct u300_pin_group {
+	const char *name;
+	const unsigned int *pins;
+	const unsigned num_pins;
+};
+
+/**
+ * struct pmx_onmask - mask bits to enable/disable padmux
+ * @mask: mask bits to disable
+ * @val: mask bits to enable
+ *
+ * onmask lazy dog:
+ * onmask = {
+ *   {"PMC1LR" mask, "PMC1LR" value},
+ *   {"PMC1HR" mask, "PMC1HR" value},
+ *   {"PMC2R"  mask, "PMC2R"  value},
+ *   {"PMC3R"  mask, "PMC3R"  value},
+ *   {"PMC4R"  mask, "PMC4R"  value}
+ * }
+ */
+struct u300_pmx_mask {
+	u16 mask;
+	u16 bits;
+};
+
+/* The chip power pins are VDD, GND, VDDIO and VSSIO */
+static const unsigned power_pins[] = { 0, 1, 3, 31, 46, 47, 49, 50, 61, 62, 63,
+	64, 78, 79, 80, 81, 92, 93, 94, 95, 101, 102, 103, 104, 115, 116, 117,
+	118, 130, 131, 132, 133, 145, 146, 147, 148, 159, 160, 172, 173, 174,
+	175, 187, 188, 189, 190, 201, 202, 211, 212, 213, 214, 215, 218, 223,
+	224, 225, 226, 231, 232, 237, 238, 239, 240, 245, 246, 251, 252, 256,
+	257, 258, 259, 264, 265, 270, 271, 276, 277, 278, 279, 284, 285, 290,
+	291, 295, 296, 299, 300, 301, 302, 303, 309, 310, 311, 312, 319, 320,
+	321, 322, 329, 330, 331, 332, 341, 342, 343, 344, 358, 359, 360, 361,
+	372, 373, 374, 375, 388, 389, 390, 391, 402, 403, 404, 405, 413, 414,
+	415, 416, 427, 428, 429, 430, 443, 444, 455, 456, 457, 458 };
+static const unsigned emif0_pins[] = { 355, 356, 357, 362, 363, 364, 365, 366,
+	367, 368, 369, 370, 371, 376, 377, 378, 379, 380, 381, 382, 383, 384,
+	385, 386, 387, 393, 394, 395, 396, 397, 398, 406, 407, 410, 411, 412,
+	417, 418 };
+static const unsigned emif1_pins[] = { 216, 217, 219, 220, 221, 222, 227, 228,
+	229, 230, 233, 234, 235, 236, 241, 242, 243, 244, 247, 248, 249, 250,
+	253, 254, 255, 260, 261, 262, 263, 266, 267, 268, 269, 272, 273, 274,
+	275, 280, 281, 282, 283, 286, 287, 288, 289, 292, 293, 294, 297, 298,
+	304, 305, 306, 307, 308, 313, 314, 315 };
+static const unsigned uart0_pins[] = { 134, 135, 136, 137 };
+static const unsigned mmc0_pins[] = { 166, 167, 168, 169, 170, 171, 176, 177 };
+static const unsigned spi0_pins[] = { 420, 421, 422, 423, 424, 425 };
+
+static const struct u300_pmx_mask emif0_mask[] = {
+	{0, 0},
+	{0, 0},
+	{0, 0},
+	{0, 0},
+	{0, 0},
+};
+
+static const struct u300_pmx_mask emif1_mask[] = {
+	/*
+	 * This connects the SDRAM to CS2 and a NAND flash to
+	 * CS0 on the EMIF.
+	 */
+	{
+		U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK |
+		U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK |
+		U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK |
+		U300_SYSCON_PMC1LR_EMIF_1_MASK,
+		U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM |
+		U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC |
+		U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF |
+		U300_SYSCON_PMC1LR_EMIF_1_SDRAM0
+	},
+	{0, 0},
+	{0, 0},
+	{0, 0},
+	{0, 0},
+};
+
+static const struct u300_pmx_mask uart0_mask[] = {
+	{0, 0},
+	{
+		U300_SYSCON_PMC1HR_APP_UART0_1_MASK |
+		U300_SYSCON_PMC1HR_APP_UART0_2_MASK,
+		U300_SYSCON_PMC1HR_APP_UART0_1_UART0 |
+		U300_SYSCON_PMC1HR_APP_UART0_2_UART0
+	},
+	{0, 0},
+	{0, 0},
+	{0, 0},
+};
+
+static const struct u300_pmx_mask mmc0_mask[] = {
+	{ U300_SYSCON_PMC1LR_MMCSD_MASK, U300_SYSCON_PMC1LR_MMCSD_MMCSD},
+	{0, 0},
+	{0, 0},
+	{0, 0},
+	{ U300_SYSCON_PMC4R_APP_MISC_12_MASK,
+	  U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO }
+};
+
+static const struct u300_pmx_mask spi0_mask[] = {
+	{0, 0},
+	{
+		U300_SYSCON_PMC1HR_APP_SPI_2_MASK |
+		U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK |
+		U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK,
+		U300_SYSCON_PMC1HR_APP_SPI_2_SPI |
+		U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI |
+		U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI
+	},
+	{0, 0},
+	{0, 0},
+	{0, 0}
+};
+
+static const struct u300_pin_group u300_pin_groups[] = {
+	{
+		.name = "powergrp",
+		.pins = power_pins,
+		.num_pins = ARRAY_SIZE(power_pins),
+	},
+	{
+		.name = "emif0grp",
+		.pins = emif0_pins,
+		.num_pins = ARRAY_SIZE(emif0_pins),
+	},
+	{
+		.name = "emif1grp",
+		.pins = emif1_pins,
+		.num_pins = ARRAY_SIZE(emif1_pins),
+	},
+	{
+		.name = "uart0grp",
+		.pins = uart0_pins,
+		.num_pins = ARRAY_SIZE(uart0_pins),
+	},
+	{
+		.name = "mmc0grp",
+		.pins = mmc0_pins,
+		.num_pins = ARRAY_SIZE(mmc0_pins),
+	},
+	{
+		.name = "spi0grp",
+		.pins = spi0_pins,
+		.num_pins = ARRAY_SIZE(spi0_pins),
+	},
+};
+
+static int u300_list_groups(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(u300_pin_groups))
+		return -EINVAL;
+	return 0;
+}
+
+static const char *u300_get_group_name(struct pinctrl_dev *pctldev,
+				       unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(u300_pin_groups))
+		return NULL;
+	return u300_pin_groups[selector].name;
+}
+
+static int u300_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector,
+			       const unsigned **pins,
+			       unsigned *num_pins)
+{
+	if (selector >= ARRAY_SIZE(u300_pin_groups))
+		return -EINVAL;
+	*pins = u300_pin_groups[selector].pins;
+	*num_pins = u300_pin_groups[selector].num_pins;
+	return 0;
+}
+
+static void u300_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
+		   unsigned offset)
+{
+	seq_printf(s, " " DRIVER_NAME);
+}
+
+static struct pinctrl_ops u300_pctrl_ops = {
+	.list_groups = u300_list_groups,
+	.get_group_name = u300_get_group_name,
+	.get_group_pins = u300_get_group_pins,
+	.pin_dbg_show = u300_pin_dbg_show,
+};
+
+/*
+ * Here we define the available functions and their corresponding pin groups
+ */
+
+/**
+ * struct u300_pmx_func - describes U300 pinmux functions
+ * @name: the name of this specific function
+ * @groups: corresponding pin groups
+ * @onmask: bits to set to enable this when doing pin muxing
+ */
+struct u300_pmx_func {
+	const char *name;
+	const char * const *groups;
+	const unsigned num_groups;
+	const struct u300_pmx_mask *mask;
+};
+
+static const char * const powergrps[] = { "powergrp" };
+static const char * const emif0grps[] = { "emif0grp" };
+static const char * const emif1grps[] = { "emif1grp" };
+static const char * const uart0grps[] = { "uart0grp" };
+static const char * const mmc0grps[] = { "mmc0grp" };
+static const char * const spi0grps[] = { "spi0grp" };
+
+static const struct u300_pmx_func u300_pmx_functions[] = {
+	{
+		.name = "power",
+		.groups = powergrps,
+		.num_groups = ARRAY_SIZE(powergrps),
+		/* Mask is N/A */
+	},
+	{
+		.name = "emif0",
+		.groups = emif0grps,
+		.num_groups = ARRAY_SIZE(emif0grps),
+		.mask = emif0_mask,
+	},
+	{
+		.name = "emif1",
+		.groups = emif1grps,
+		.num_groups = ARRAY_SIZE(emif1grps),
+		.mask = emif1_mask,
+	},
+	{
+		.name = "uart0",
+		.groups = uart0grps,
+		.num_groups = ARRAY_SIZE(uart0grps),
+		.mask = uart0_mask,
+	},
+	{
+		.name = "mmc0",
+		.groups = mmc0grps,
+		.num_groups = ARRAY_SIZE(mmc0grps),
+		.mask = mmc0_mask,
+	},
+	{
+		.name = "spi0",
+		.groups = spi0grps,
+		.num_groups = ARRAY_SIZE(spi0grps),
+		.mask = spi0_mask,
+	},
+};
+
+static void u300_pmx_endisable(struct u300_pmx *upmx, unsigned selector,
+			       bool enable)
+{
+	u16 regval, val, mask;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(u300_pmx_registers); i++) {
+		if (enable)
+			val = u300_pmx_functions[selector].mask->bits;
+		else
+			val = 0;
+
+		mask = u300_pmx_functions[selector].mask->mask;
+		if (mask != 0) {
+			regval = readw(upmx->virtbase + u300_pmx_registers[i]);
+			regval &= ~mask;
+			regval |= val;
+			writew(regval, upmx->virtbase + u300_pmx_registers[i]);
+		}
+	}
+}
+
+static int u300_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector,
+			   unsigned group)
+{
+	struct u300_pmx *upmx;
+
+	/* There is nothing to do with the power pins */
+	if (selector == 0)
+		return 0;
+
+	upmx = pinctrl_dev_get_drvdata(pctldev);
+	u300_pmx_endisable(upmx, selector, true);
+
+	return 0;
+}
+
+static void u300_pmx_disable(struct pinctrl_dev *pctldev, unsigned selector,
+			     unsigned group)
+{
+	struct u300_pmx *upmx;
+
+	/* There is nothing to do with the power pins */
+	if (selector == 0)
+		return;
+
+	upmx = pinctrl_dev_get_drvdata(pctldev);
+	u300_pmx_endisable(upmx, selector, false);
+}
+
+static int u300_pmx_list_funcs(struct pinctrl_dev *pctldev, unsigned selector)
+{
+	if (selector >= ARRAY_SIZE(u300_pmx_functions))
+		return -EINVAL;
+	return 0;
+}
+
+static const char *u300_pmx_get_func_name(struct pinctrl_dev *pctldev,
+					  unsigned selector)
+{
+	return u300_pmx_functions[selector].name;
+}
+
+static int u300_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector,
+			       const char * const **groups,
+			       unsigned * const num_groups)
+{
+	*groups = u300_pmx_functions[selector].groups;
+	*num_groups = u300_pmx_functions[selector].num_groups;
+	return 0;
+}
+
+static struct pinmux_ops u300_pmx_ops = {
+	.list_functions = u300_pmx_list_funcs,
+	.get_function_name = u300_pmx_get_func_name,
+	.get_function_groups = u300_pmx_get_groups,
+	.enable = u300_pmx_enable,
+	.disable = u300_pmx_disable,
+};
+
+/*
+ * FIXME: this will be set to sane values as this driver engulfs
+ * drivers/gpio/gpio-u300.c and we really know this stuff.
+ */
+static struct pinctrl_gpio_range u300_gpio_range = {
+	.name = "COH901*",
+	.id = 0,
+	.base = 0,
+	.npins = 64,
+};
+
+static struct pinctrl_desc u300_pmx_desc = {
+	.name = DRIVER_NAME,
+	.pins = u300_pads,
+	.npins = ARRAY_SIZE(u300_pads),
+	.maxpin = U300_NUM_PADS-1,
+	.pctlops = &u300_pctrl_ops,
+	.pmxops = &u300_pmx_ops,
+	.owner = THIS_MODULE,
+};
+
+static int __init u300_pmx_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct u300_pmx *upmx;
+	struct resource *res;
+
+	/* Create state holders etc for this driver */
+	upmx = devm_kzalloc(&pdev->dev, sizeof(*upmx), GFP_KERNEL);
+	if (!upmx)
+		return -ENOMEM;
+
+	upmx->dev = &pdev->dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		ret = -ENOENT;
+		goto out_no_resource;
+	}
+	upmx->phybase = res->start;
+	upmx->physize = resource_size(res);
+
+	if (request_mem_region(upmx->phybase, upmx->physize,
+			       DRIVER_NAME) == NULL) {
+		ret = -ENOMEM;
+		goto out_no_memregion;
+	}
+
+	upmx->virtbase = ioremap(upmx->phybase, upmx->physize);
+	if (!upmx->virtbase) {
+		ret = -ENOMEM;
+		goto out_no_remap;
+	}
+
+	upmx->pctl = pinctrl_register(&u300_pmx_desc, &pdev->dev, upmx);
+	if (!upmx->pctl) {
+		dev_err(&pdev->dev, "could not register U300 pinmux driver\n");
+		ret = -EINVAL;
+		goto out_no_pmx;
+	}
+
+	/* We will handle a range of GPIO pins */
+	pinctrl_add_gpio_range(upmx->pctl, &u300_gpio_range);
+
+	platform_set_drvdata(pdev, upmx);
+
+	dev_info(&pdev->dev, "initialized U300 pinmux driver\n");
+
+	return 0;
+
+out_no_pmx:
+	iounmap(upmx->virtbase);
+out_no_remap:
+	platform_set_drvdata(pdev, NULL);
+out_no_memregion:
+	release_mem_region(upmx->phybase, upmx->physize);
+out_no_resource:
+	devm_kfree(&pdev->dev, upmx);
+	return ret;
+}
+
+static int __exit u300_pmx_remove(struct platform_device *pdev)
+{
+	struct u300_pmx *upmx = platform_get_drvdata(pdev);
+
+	pinctrl_remove_gpio_range(upmx->pctl, &u300_gpio_range);
+	pinctrl_unregister(upmx->pctl);
+	iounmap(upmx->virtbase);
+	release_mem_region(upmx->phybase, upmx->physize);
+	platform_set_drvdata(pdev, NULL);
+	devm_kfree(&pdev->dev, upmx);
+
+	return 0;
+}
+
+static struct platform_driver u300_pmx_driver = {
+	.driver = {
+		.name = DRIVER_NAME,
+		.owner = THIS_MODULE,
+	},
+	.remove = __exit_p(u300_pmx_remove),
+};
+
+static int __init u300_pmx_init(void)
+{
+	return platform_driver_probe(&u300_pmx_driver, u300_pmx_probe);
+}
+arch_initcall(u300_pmx_init);
+
+static void __exit u300_pmx_exit(void)
+{
+	platform_driver_unregister(&u300_pmx_driver);
+}
+module_exit(u300_pmx_exit);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
+MODULE_DESCRIPTION("U300 pin control driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/pinctrl/pinmux.c b/drivers/pinctrl/pinmux.c
new file mode 100644
index 00000000000000..a5467f8709e9a7
--- /dev/null
+++ b/drivers/pinctrl/pinmux.c
@@ -0,0 +1,1190 @@
+/*
+ * Core driver for the pin muxing portions of the pin control subsystem
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ * Based on bits of regulator core, gpio core and clk core
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#define pr_fmt(fmt) "pinmux core: " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/slab.h>
+#include <linux/radix-tree.h>
+#include <linux/err.h>
+#include <linux/list.h>
+#include <linux/mutex.h>
+#include <linux/spinlock.h>
+#include <linux/sysfs.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/pinctrl/machine.h>
+#include <linux/pinctrl/pinmux.h>
+#include "core.h"
+
+/* List of pinmuxes */
+static DEFINE_MUTEX(pinmux_list_mutex);
+static LIST_HEAD(pinmux_list);
+
+/* List of pinmux hogs */
+static DEFINE_MUTEX(pinmux_hoglist_mutex);
+static LIST_HEAD(pinmux_hoglist);
+
+/* Global pinmux maps, we allow one set only */
+static struct pinmux_map const *pinmux_maps;
+static unsigned pinmux_maps_num;
+
+/**
+ * struct pinmux_group - group list item for pinmux groups
+ * @node: pinmux group list node
+ * @group_selector: the group selector for this group
+ */
+struct pinmux_group {
+	struct list_head node;
+	unsigned group_selector;
+};
+
+/**
+ * struct pinmux - per-device pinmux state holder
+ * @node: global list node
+ * @dev: the device using this pinmux
+ * @usecount: the number of active users of this mux setting, used to keep
+ *	track of nested use cases
+ * @pins: an array of discrete physical pins used in this mapping, taken
+ *	from the global pin enumeration space (copied from pinmux map)
+ * @num_pins: the number of pins in this mapping array, i.e. the number of
+ *	elements in .pins so we can iterate over that array (copied from
+ *	pinmux map)
+ * @pctldev: pin control device handling this pinmux
+ * @func_selector: the function selector for the pinmux device handling
+ *	this pinmux
+ * @groups: the group selectors for the pinmux device and
+ *	selector combination handling this pinmux, this is a list that
+ *	will be traversed on all pinmux operations such as
+ *	get/put/enable/disable
+ * @mutex: a lock for the pinmux state holder
+ */
+struct pinmux {
+	struct list_head node;
+	struct device *dev;
+	unsigned usecount;
+	struct pinctrl_dev *pctldev;
+	unsigned func_selector;
+	struct list_head groups;
+	struct mutex mutex;
+};
+
+/**
+ * struct pinmux_hog - a list item to stash mux hogs
+ * @node: pinmux hog list node
+ * @map: map entry responsible for this hogging
+ * @pmx: the pinmux hogged by this item
+ */
+struct pinmux_hog {
+	struct list_head node;
+	struct pinmux_map const *map;
+	struct pinmux *pmx;
+};
+
+/**
+ * pin_request() - request a single pin to be muxed in, typically for GPIO
+ * @pin: the pin number in the global pin space
+ * @function: a functional name to give to this pin, passed to the driver
+ *	so it knows what function to mux in, e.g. the string "gpioNN"
+ *	means that you want to mux in the pin for use as GPIO number NN
+ * @gpio: if this request concerns a single GPIO pin
+ * @gpio_range: the range matching the GPIO pin if this is a request for a
+ *	single GPIO pin
+ */
+static int pin_request(struct pinctrl_dev *pctldev,
+		       int pin, const char *function, bool gpio,
+		       struct pinctrl_gpio_range *gpio_range)
+{
+	struct pin_desc *desc;
+	const struct pinmux_ops *ops = pctldev->desc->pmxops;
+	int status = -EINVAL;
+
+	dev_dbg(&pctldev->dev, "request pin %d for %s\n", pin, function);
+
+	if (!pin_is_valid(pctldev, pin)) {
+		dev_err(&pctldev->dev, "pin is invalid\n");
+		return -EINVAL;
+	}
+
+	if (!function) {
+		dev_err(&pctldev->dev, "no function name given\n");
+		return -EINVAL;
+	}
+
+	desc = pin_desc_get(pctldev, pin);
+	if (desc == NULL) {
+		dev_err(&pctldev->dev,
+			"pin is not registered so it cannot be requested\n");
+		goto out;
+	}
+
+	spin_lock(&desc->lock);
+	if (desc->mux_function) {
+		spin_unlock(&desc->lock);
+		dev_err(&pctldev->dev,
+			"pin already requested\n");
+		goto out;
+	}
+	desc->mux_function = function;
+	spin_unlock(&desc->lock);
+
+	/* Let each pin increase references to this module */
+	if (!try_module_get(pctldev->owner)) {
+		dev_err(&pctldev->dev,
+			"could not increase module refcount for pin %d\n",
+			pin);
+		status = -EINVAL;
+		goto out_free_pin;
+	}
+
+	/*
+	 * If there is no kind of request function for the pin we just assume
+	 * we got it by default and proceed.
+	 */
+	if (gpio && ops->gpio_request_enable)
+		/* This requests and enables a single GPIO pin */
+		status = ops->gpio_request_enable(pctldev, gpio_range, pin);
+	else if (ops->request)
+		status = ops->request(pctldev, pin);
+	else
+		status = 0;
+
+	if (status)
+		dev_err(&pctldev->dev, "->request on device %s failed "
+		       "for pin %d\n",
+		       pctldev->desc->name, pin);
+out_free_pin:
+	if (status) {
+		spin_lock(&desc->lock);
+		desc->mux_function = NULL;
+		spin_unlock(&desc->lock);
+	}
+out:
+	if (status)
+		dev_err(&pctldev->dev, "pin-%d (%s) status %d\n",
+		       pin, function ? : "?", status);
+
+	return status;
+}
+
+/**
+ * pin_free() - release a single muxed in pin so something else can be muxed
+ * @pctldev: pin controller device handling this pin
+ * @pin: the pin to free
+ * @free_func: whether to free the pin's assigned function name string
+ */
+static void pin_free(struct pinctrl_dev *pctldev, int pin, int free_func)
+{
+	const struct pinmux_ops *ops = pctldev->desc->pmxops;
+	struct pin_desc *desc;
+
+	desc = pin_desc_get(pctldev, pin);
+	if (desc == NULL) {
+		dev_err(&pctldev->dev,
+			"pin is not registered so it cannot be freed\n");
+		return;
+	}
+
+	if (ops->free)
+		ops->free(pctldev, pin);
+
+	spin_lock(&desc->lock);
+	if (free_func)
+		kfree(desc->mux_function);
+	desc->mux_function = NULL;
+	spin_unlock(&desc->lock);
+	module_put(pctldev->owner);
+}
+
+/**
+ * pinmux_request_gpio() - request a single pin to be muxed in as GPIO
+ * @gpio: the GPIO pin number from the GPIO subsystem number space
+ */
+int pinmux_request_gpio(unsigned gpio)
+{
+	char gpiostr[16];
+	const char *function;
+	struct pinctrl_dev *pctldev;
+	struct pinctrl_gpio_range *range;
+	int ret;
+	int pin;
+
+	ret = pinctrl_get_device_gpio_range(gpio, &pctldev, &range);
+	if (ret)
+		return -EINVAL;
+
+	/* Convert to the pin controllers number space */
+	pin = gpio - range->base;
+
+	/* Conjure some name stating what chip and pin this is taken by */
+	snprintf(gpiostr, 15, "%s:%d", range->name, gpio);
+
+	function = kstrdup(gpiostr, GFP_KERNEL);
+	if (!function)
+		return -EINVAL;
+
+	ret = pin_request(pctldev, pin, function, true, range);
+	if (ret < 0)
+		kfree(function);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(pinmux_request_gpio);
+
+/**
+ * pinmux_free_gpio() - free a single pin, currently used as GPIO
+ * @gpio: the GPIO pin number from the GPIO subsystem number space
+ */
+void pinmux_free_gpio(unsigned gpio)
+{
+	struct pinctrl_dev *pctldev;
+	struct pinctrl_gpio_range *range;
+	int ret;
+	int pin;
+
+	ret = pinctrl_get_device_gpio_range(gpio, &pctldev, &range);
+	if (ret)
+		return;
+
+	/* Convert to the pin controllers number space */
+	pin = gpio - range->base;
+
+	pin_free(pctldev, pin, true);
+}
+EXPORT_SYMBOL_GPL(pinmux_free_gpio);
+
+/**
+ * pinmux_register_mappings() - register a set of pinmux mappings
+ * @maps: the pinmux mappings table to register
+ * @num_maps: the number of maps in the mapping table
+ *
+ * Only call this once during initialization of your machine, the function is
+ * tagged as __init and won't be callable after init has completed. The map
+ * passed into this function will be owned by the pinmux core and cannot be
+ * free:d.
+ */
+int __init pinmux_register_mappings(struct pinmux_map const *maps,
+				    unsigned num_maps)
+{
+	int i;
+
+	if (pinmux_maps != NULL) {
+		pr_err("pinmux mappings already registered, you can only "
+		       "register one set of maps\n");
+		return -EINVAL;
+	}
+
+	pr_debug("add %d pinmux maps\n", num_maps);
+	for (i = 0; i < num_maps; i++) {
+		/* Sanity check the mapping */
+		if (!maps[i].name) {
+			pr_err("failed to register map %d: "
+			       "no map name given\n", i);
+			return -EINVAL;
+		}
+		if (!maps[i].ctrl_dev && !maps[i].ctrl_dev_name) {
+			pr_err("failed to register map %s (%d): "
+			       "no pin control device given\n",
+			       maps[i].name, i);
+			return -EINVAL;
+		}
+		if (!maps[i].function) {
+			pr_err("failed to register map %s (%d): "
+			       "no function ID given\n", maps[i].name, i);
+			return -EINVAL;
+		}
+
+		if (!maps[i].dev && !maps[i].dev_name)
+			pr_debug("add system map %s function %s with no device\n",
+				 maps[i].name,
+				 maps[i].function);
+		else
+			pr_debug("register map %s, function %s\n",
+				 maps[i].name,
+				 maps[i].function);
+	}
+
+	pinmux_maps = maps;
+	pinmux_maps_num = num_maps;
+
+	return 0;
+}
+
+/**
+ * acquire_pins() - acquire all the pins for a certain funcion on a pinmux
+ * @pctldev: the device to take the pins on
+ * @func_selector: the function selector to acquire the pins for
+ * @group_selector: the group selector containing the pins to acquire
+ */
+static int acquire_pins(struct pinctrl_dev *pctldev,
+			unsigned func_selector,
+			unsigned group_selector)
+{
+	const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
+	const struct pinmux_ops *pmxops = pctldev->desc->pmxops;
+	const char *func = pmxops->get_function_name(pctldev,
+						     func_selector);
+	const unsigned *pins;
+	unsigned num_pins;
+	int ret;
+	int i;
+
+	ret = pctlops->get_group_pins(pctldev, group_selector,
+				      &pins, &num_pins);
+	if (ret)
+		return ret;
+
+	dev_dbg(&pctldev->dev, "requesting the %u pins from group %u\n",
+		num_pins, group_selector);
+
+	/* Try to allocate all pins in this group, one by one */
+	for (i = 0; i < num_pins; i++) {
+		ret = pin_request(pctldev, pins[i], func, false, NULL);
+		if (ret) {
+			dev_err(&pctldev->dev,
+				"could not get pin %d for function %s "
+				"on device %s - conflicting mux mappings?\n",
+				pins[i], func ? : "(undefined)",
+				pinctrl_dev_get_name(pctldev));
+			/* On error release all taken pins */
+			i--; /* this pin just failed */
+			for (; i >= 0; i--)
+				pin_free(pctldev, pins[i], false);
+			return -ENODEV;
+		}
+	}
+	return 0;
+}
+
+/**
+ * release_pins() - release pins taken by earlier acquirement
+ * @pctldev: the device to free the pinx on
+ * @group_selector: the group selector containing the pins to free
+ */
+static void release_pins(struct pinctrl_dev *pctldev,
+			 unsigned group_selector)
+{
+	const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
+	const unsigned *pins;
+	unsigned num_pins;
+	int ret;
+	int i;
+
+	ret = pctlops->get_group_pins(pctldev, group_selector,
+				      &pins, &num_pins);
+	if (ret) {
+		dev_err(&pctldev->dev, "could not get pins to release for "
+			"group selector %d\n",
+			group_selector);
+		return;
+	}
+	for (i = 0; i < num_pins; i++)
+		pin_free(pctldev, pins[i], false);
+}
+
+/**
+ * pinmux_get_group_selector() - returns the group selector for a group
+ * @pctldev: the pin controller handling the group
+ * @pin_group: the pin group to look up
+ */
+static int pinmux_get_group_selector(struct pinctrl_dev *pctldev,
+				     const char *pin_group)
+{
+	const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
+	unsigned group_selector = 0;
+
+	while (pctlops->list_groups(pctldev, group_selector) >= 0) {
+		const char *gname = pctlops->get_group_name(pctldev,
+							    group_selector);
+		if (!strcmp(gname, pin_group)) {
+			dev_dbg(&pctldev->dev,
+				"found group selector %u for %s\n",
+				group_selector,
+				pin_group);
+			return group_selector;
+		}
+
+		group_selector++;
+	}
+
+	dev_err(&pctldev->dev, "does not have pin group %s\n",
+		pin_group);
+
+	return -EINVAL;
+}
+
+/**
+ * pinmux_check_pin_group() - check function and pin group combo
+ * @pctldev: device to check the pin group vs function for
+ * @func_selector: the function selector to check the pin group for, we have
+ *	already looked this up in the calling function
+ * @pin_group: the pin group to match to the function
+ *
+ * This function will check that the pinmux driver can supply the
+ * selected pin group for a certain function, returns the group selector if
+ * the group and function selector will work fine together, else returns
+ * negative
+ */
+static int pinmux_check_pin_group(struct pinctrl_dev *pctldev,
+				  unsigned func_selector,
+				  const char *pin_group)
+{
+	const struct pinmux_ops *pmxops = pctldev->desc->pmxops;
+	const struct pinctrl_ops *pctlops = pctldev->desc->pctlops;
+	int ret;
+
+	/*
+	 * If the driver does not support different pin groups for the
+	 * functions, we only support group 0, and assume this exists.
+	 */
+	if (!pctlops || !pctlops->list_groups)
+		return 0;
+
+	/*
+	 * Passing NULL (no specific group) will select the first and
+	 * hopefully only group of pins available for this function.
+	 */
+	if (!pin_group) {
+		char const * const *groups;
+		unsigned num_groups;
+
+		ret = pmxops->get_function_groups(pctldev, func_selector,
+						  &groups, &num_groups);
+		if (ret)
+			return ret;
+		if (num_groups < 1)
+			return -EINVAL;
+		ret = pinmux_get_group_selector(pctldev, groups[0]);
+		if (ret < 0) {
+			dev_err(&pctldev->dev,
+				"function %s wants group %s but the pin "
+				"controller does not seem to have that group\n",
+				pmxops->get_function_name(pctldev, func_selector),
+				groups[0]);
+			return ret;
+		}
+
+		if (num_groups > 1)
+			dev_dbg(&pctldev->dev,
+				"function %s support more than one group, "
+				"default-selecting first group %s (%d)\n",
+				pmxops->get_function_name(pctldev, func_selector),
+				groups[0],
+				ret);
+
+		return ret;
+	}
+
+	dev_dbg(&pctldev->dev,
+		"check if we have pin group %s on controller %s\n",
+		pin_group, pinctrl_dev_get_name(pctldev));
+
+	ret = pinmux_get_group_selector(pctldev, pin_group);
+	if (ret < 0) {
+		dev_dbg(&pctldev->dev,
+			"%s does not support pin group %s with function %s\n",
+			pinctrl_dev_get_name(pctldev),
+			pin_group,
+			pmxops->get_function_name(pctldev, func_selector));
+	}
+	return ret;
+}
+
+/**
+ * pinmux_search_function() - check pin control driver for a certain function
+ * @pctldev: device to check for function and position
+ * @map: function map containing the function and position to look for
+ * @func_selector: returns the applicable function selector if found
+ * @group_selector: returns the applicable group selector if found
+ *
+ * This will search the pinmux driver for an applicable
+ * function with a specific pin group, returns 0 if these can be mapped
+ * negative otherwise
+ */
+static int pinmux_search_function(struct pinctrl_dev *pctldev,
+				  struct pinmux_map const *map,
+				  unsigned *func_selector,
+				  unsigned *group_selector)
+{
+	const struct pinmux_ops *ops = pctldev->desc->pmxops;
+	unsigned selector = 0;
+
+	/* See if this pctldev has this function */
+	while (ops->list_functions(pctldev, selector) >= 0) {
+		const char *fname = ops->get_function_name(pctldev,
+							   selector);
+		int ret;
+
+		if (!strcmp(map->function, fname)) {
+			/* Found the function, check pin group */
+			ret = pinmux_check_pin_group(pctldev, selector,
+						     map->group);
+			if (ret < 0)
+				return ret;
+
+			/* This function and group selector can be used */
+			*func_selector = selector;
+			*group_selector = ret;
+			return 0;
+
+		}
+		selector++;
+	}
+
+	pr_err("%s does not support function %s\n",
+	       pinctrl_dev_get_name(pctldev), map->function);
+	return -EINVAL;
+}
+
+/**
+ * pinmux_enable_muxmap() - enable a map entry for a certain pinmux
+ */
+static int pinmux_enable_muxmap(struct pinctrl_dev *pctldev,
+				struct pinmux *pmx,
+				struct device *dev,
+				const char *devname,
+				struct pinmux_map const *map)
+{
+	unsigned func_selector;
+	unsigned group_selector;
+	struct pinmux_group *grp;
+	int ret;
+
+	/*
+	 * Note that we're not locking the pinmux mutex here, because
+	 * this is only called at pinmux initialization time when it
+	 * has not been added to any list and thus is not reachable
+	 * by anyone else.
+	 */
+
+	if (pmx->pctldev && pmx->pctldev != pctldev) {
+		dev_err(&pctldev->dev,
+			"different pin control devices given for device %s, "
+			"function %s\n",
+			devname,
+			map->function);
+		return -EINVAL;
+	}
+	pmx->dev = dev;
+	pmx->pctldev = pctldev;
+
+	/* Now go into the driver and try to match a function and group */
+	ret = pinmux_search_function(pctldev, map, &func_selector,
+				     &group_selector);
+	if (ret < 0)
+		return ret;
+
+	/*
+	 * If the function selector is already set, it needs to be identical,
+	 * we support several groups with one function but not several
+	 * functions with one or several groups in the same pinmux.
+	 */
+	if (pmx->func_selector != UINT_MAX &&
+	    pmx->func_selector != func_selector) {
+		dev_err(&pctldev->dev,
+			"dual function defines in the map for device %s\n",
+		       devname);
+		return -EINVAL;
+	}
+	pmx->func_selector = func_selector;
+
+	/* Now add this group selector, we may have many of them */
+	grp = kmalloc(sizeof(struct pinmux_group), GFP_KERNEL);
+	if (!grp)
+		return -ENOMEM;
+	grp->group_selector = group_selector;
+	ret = acquire_pins(pctldev, func_selector, group_selector);
+	if (ret) {
+		kfree(grp);
+		return ret;
+	}
+	list_add(&grp->node, &pmx->groups);
+
+	return 0;
+}
+
+static void pinmux_free_groups(struct pinmux *pmx)
+{
+	struct list_head *node, *tmp;
+
+	list_for_each_safe(node, tmp, &pmx->groups) {
+		struct pinmux_group *grp =
+			list_entry(node, struct pinmux_group, node);
+		/* Release all pins taken by this group */
+		release_pins(pmx->pctldev, grp->group_selector);
+		list_del(node);
+		kfree(grp);
+	}
+}
+
+/**
+ * pinmux_get() - retrieves the pinmux for a certain device
+ * @dev: the device to get the pinmux for
+ * @name: an optional specific mux mapping name or NULL, the name is only
+ *	needed if you want to have more than one mapping per device, or if you
+ *	need an anonymous pinmux (not tied to any specific device)
+ */
+struct pinmux *pinmux_get(struct device *dev, const char *name)
+{
+
+	struct pinmux_map const *map = NULL;
+	struct pinctrl_dev *pctldev = NULL;
+	const char *devname = NULL;
+	struct pinmux *pmx;
+	bool found_map;
+	unsigned num_maps = 0;
+	int ret = -ENODEV;
+	int i;
+
+	/* We must have dev or ID or both */
+	if (!dev && !name)
+		return ERR_PTR(-EINVAL);
+
+	if (dev)
+		devname = dev_name(dev);
+
+	pr_debug("get mux %s for device %s\n", name,
+		 devname ? devname : "(none)");
+
+	/*
+	 * create the state cookie holder struct pinmux for each
+	 * mapping, this is what consumers will get when requesting
+	 * a pinmux handle with pinmux_get()
+	 */
+	pmx = kzalloc(sizeof(struct pinmux), GFP_KERNEL);
+	if (pmx == NULL)
+		return ERR_PTR(-ENOMEM);
+	mutex_init(&pmx->mutex);
+	pmx->func_selector = UINT_MAX;
+	INIT_LIST_HEAD(&pmx->groups);
+
+	/* Iterate over the pinmux maps to locate the right ones */
+	for (i = 0; i < pinmux_maps_num; i++) {
+		map = &pinmux_maps[i];
+		found_map = false;
+
+		/*
+		 * First, try to find the pctldev given in the map
+		 */
+		pctldev = get_pinctrl_dev_from_dev(map->ctrl_dev,
+						   map->ctrl_dev_name);
+		if (!pctldev) {
+			const char *devname = NULL;
+
+			if (map->ctrl_dev)
+				devname = dev_name(map->ctrl_dev);
+			else if (map->ctrl_dev_name)
+				devname = map->ctrl_dev_name;
+
+			pr_warning("could not find a pinctrl device for pinmux "
+				   "function %s, fishy, they shall all have one\n",
+				   map->function);
+			pr_warning("given pinctrl device name: %s",
+				   devname ? devname : "UNDEFINED");
+
+			/* Continue to check the other mappings anyway... */
+			continue;
+		}
+
+		pr_debug("in map, found pctldev %s to handle function %s",
+			 dev_name(&pctldev->dev), map->function);
+
+
+		/*
+		 * If we're looking for a specific named map, this must match,
+		 * else we loop and look for the next.
+		 */
+		if (name != NULL) {
+			if (map->name == NULL)
+				continue;
+			if (strcmp(map->name, name))
+				continue;
+		}
+
+		/*
+		 * This is for the case where no device name is given, we
+		 * already know that the function name matches from above
+		 * code.
+		 */
+		if (!map->dev_name && (name != NULL))
+			found_map = true;
+
+		/* If the mapping has a device set up it must match */
+		if (map->dev_name &&
+		    (!devname || !strcmp(map->dev_name, devname)))
+			/* MATCH! */
+			found_map = true;
+
+		/* If this map is applicable, then apply it */
+		if (found_map) {
+			ret = pinmux_enable_muxmap(pctldev, pmx, dev,
+						   devname, map);
+			if (ret) {
+				pinmux_free_groups(pmx);
+				kfree(pmx);
+				return ERR_PTR(ret);
+			}
+			num_maps++;
+		}
+	}
+
+
+	/* We should have atleast one map, right */
+	if (!num_maps) {
+		pr_err("could not find any mux maps for device %s, ID %s\n",
+		       devname ? devname : "(anonymous)",
+		       name ? name : "(undefined)");
+		kfree(pmx);
+		return ERR_PTR(-EINVAL);
+	}
+
+	pr_debug("found %u mux maps for device %s, UD %s\n",
+		 num_maps,
+		 devname ? devname : "(anonymous)",
+		 name ? name : "(undefined)");
+
+	/* Add the pinmux to the global list */
+	mutex_lock(&pinmux_list_mutex);
+	list_add(&pmx->node, &pinmux_list);
+	mutex_unlock(&pinmux_list_mutex);
+
+	return pmx;
+}
+EXPORT_SYMBOL_GPL(pinmux_get);
+
+/**
+ * pinmux_put() - release a previously claimed pinmux
+ * @pmx: a pinmux previously claimed by pinmux_get()
+ */
+void pinmux_put(struct pinmux *pmx)
+{
+	if (pmx == NULL)
+		return;
+
+	mutex_lock(&pmx->mutex);
+	if (pmx->usecount)
+		pr_warn("releasing pinmux with active users!\n");
+	/* Free the groups and all acquired pins */
+	pinmux_free_groups(pmx);
+	mutex_unlock(&pmx->mutex);
+
+	/* Remove from list */
+	mutex_lock(&pinmux_list_mutex);
+	list_del(&pmx->node);
+	mutex_unlock(&pinmux_list_mutex);
+
+	kfree(pmx);
+}
+EXPORT_SYMBOL_GPL(pinmux_put);
+
+/**
+ * pinmux_enable() - enable a certain pinmux setting
+ * @pmx: the pinmux to enable, previously claimed by pinmux_get()
+ */
+int pinmux_enable(struct pinmux *pmx)
+{
+	int ret = 0;
+
+	if (pmx == NULL)
+		return -EINVAL;
+	mutex_lock(&pmx->mutex);
+	if (pmx->usecount++ == 0) {
+		struct pinctrl_dev *pctldev = pmx->pctldev;
+		const struct pinmux_ops *ops = pctldev->desc->pmxops;
+		struct pinmux_group *grp;
+
+		list_for_each_entry(grp, &pmx->groups, node) {
+			ret = ops->enable(pctldev, pmx->func_selector,
+					  grp->group_selector);
+			if (ret) {
+				/*
+				 * TODO: call disable() on all groups we called
+				 * enable() on to this point?
+				 */
+				pmx->usecount--;
+				break;
+			}
+		}
+	}
+	mutex_unlock(&pmx->mutex);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(pinmux_enable);
+
+/**
+ * pinmux_disable() - disable a certain pinmux setting
+ * @pmx: the pinmux to disable, previously claimed by pinmux_get()
+ */
+void pinmux_disable(struct pinmux *pmx)
+{
+	if (pmx == NULL)
+		return;
+
+	mutex_lock(&pmx->mutex);
+	if (--pmx->usecount == 0) {
+		struct pinctrl_dev *pctldev = pmx->pctldev;
+		const struct pinmux_ops *ops = pctldev->desc->pmxops;
+		struct pinmux_group *grp;
+
+		list_for_each_entry(grp, &pmx->groups, node) {
+			ops->disable(pctldev, pmx->func_selector,
+				     grp->group_selector);
+		}
+	}
+	mutex_unlock(&pmx->mutex);
+}
+EXPORT_SYMBOL_GPL(pinmux_disable);
+
+int pinmux_check_ops(const struct pinmux_ops *ops)
+{
+	/* Check that we implement required operations */
+	if (!ops->list_functions ||
+	    !ops->get_function_name ||
+	    !ops->get_function_groups ||
+	    !ops->enable ||
+	    !ops->disable)
+		return -EINVAL;
+
+	return 0;
+}
+
+/* Hog a single map entry and add to the hoglist */
+static int pinmux_hog_map(struct pinctrl_dev *pctldev,
+			  struct pinmux_map const *map)
+{
+	struct pinmux_hog *hog;
+	struct pinmux *pmx;
+	int ret;
+
+	if (map->dev || map->dev_name) {
+		/*
+		 * TODO: the day we have device tree support, we can
+		 * traverse the device tree and hog to specific device nodes
+		 * without any problems, so then we can hog pinmuxes for
+		 * all devices that just want a static pin mux at this point.
+		 */
+		dev_err(&pctldev->dev, "map %s wants to hog a non-system "
+			"pinmux, this is not going to work\n", map->name);
+		return -EINVAL;
+	}
+
+	hog = kzalloc(sizeof(struct pinmux_hog), GFP_KERNEL);
+	if (!hog)
+		return -ENOMEM;
+
+	pmx = pinmux_get(NULL, map->name);
+	if (IS_ERR(pmx)) {
+		kfree(hog);
+		dev_err(&pctldev->dev,
+			"could not get the %s pinmux mapping for hogging\n",
+			map->name);
+		return PTR_ERR(pmx);
+	}
+
+	ret = pinmux_enable(pmx);
+	if (ret) {
+		pinmux_put(pmx);
+		kfree(hog);
+		dev_err(&pctldev->dev,
+			"could not enable the %s pinmux mapping for hogging\n",
+			map->name);
+		return ret;
+	}
+
+	hog->map = map;
+	hog->pmx = pmx;
+
+	dev_info(&pctldev->dev, "hogged map %s, function %s\n", map->name,
+		 map->function);
+	mutex_lock(&pctldev->pinmux_hogs_lock);
+	list_add(&hog->node, &pctldev->pinmux_hogs);
+	mutex_unlock(&pctldev->pinmux_hogs_lock);
+
+	return 0;
+}
+
+/**
+ * pinmux_hog_maps() - hog specific map entries on controller device
+ * @pctldev: the pin control device to hog entries on
+ *
+ * When the pin controllers are registered, there may be some specific pinmux
+ * map entries that need to be hogged, i.e. get+enabled until the system shuts
+ * down.
+ */
+int pinmux_hog_maps(struct pinctrl_dev *pctldev)
+{
+	struct device *dev = &pctldev->dev;
+	const char *devname = dev_name(dev);
+	int ret;
+	int i;
+
+	INIT_LIST_HEAD(&pctldev->pinmux_hogs);
+	mutex_init(&pctldev->pinmux_hogs_lock);
+
+	for (i = 0; i < pinmux_maps_num; i++) {
+		struct pinmux_map const *map = &pinmux_maps[i];
+
+		if (((map->ctrl_dev == dev) ||
+		     !strcmp(map->ctrl_dev_name, devname)) &&
+		    map->hog_on_boot) {
+			/* OK time to hog! */
+			ret = pinmux_hog_map(pctldev, map);
+			if (ret)
+				return ret;
+		}
+	}
+	return 0;
+}
+
+/**
+ * pinmux_hog_maps() - unhog specific map entries on controller device
+ * @pctldev: the pin control device to unhog entries on
+ */
+void pinmux_unhog_maps(struct pinctrl_dev *pctldev)
+{
+	struct list_head *node, *tmp;
+
+	mutex_lock(&pctldev->pinmux_hogs_lock);
+	list_for_each_safe(node, tmp, &pctldev->pinmux_hogs) {
+		struct pinmux_hog *hog =
+			list_entry(node, struct pinmux_hog, node);
+		pinmux_disable(hog->pmx);
+		pinmux_put(hog->pmx);
+		list_del(node);
+		kfree(hog);
+	}
+	mutex_unlock(&pctldev->pinmux_hogs_lock);
+}
+
+#ifdef CONFIG_DEBUG_FS
+
+/* Called from pincontrol core */
+static int pinmux_functions_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev = s->private;
+	const struct pinmux_ops *pmxops = pctldev->desc->pmxops;
+	unsigned func_selector = 0;
+
+	while (pmxops->list_functions(pctldev, func_selector) >= 0) {
+		const char *func = pmxops->get_function_name(pctldev,
+							  func_selector);
+		const char * const *groups;
+		unsigned num_groups;
+		int ret;
+		int i;
+
+		ret = pmxops->get_function_groups(pctldev, func_selector,
+						  &groups, &num_groups);
+		if (ret)
+			seq_printf(s, "function %s: COULD NOT GET GROUPS\n",
+				   func);
+
+		seq_printf(s, "function: %s, groups = [ ", func);
+		for (i = 0; i < num_groups; i++)
+			seq_printf(s, "%s ", groups[i]);
+		seq_puts(s, "]\n");
+
+		func_selector++;
+
+	}
+
+	return 0;
+}
+
+static int pinmux_pins_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev = s->private;
+	unsigned pin;
+
+	seq_puts(s, "Pinmux settings per pin\n");
+	seq_puts(s, "Format: pin (name): pinmuxfunction\n");
+
+	/* The highest pin number need to be included in the loop, thus <= */
+	for (pin = 0; pin <= pctldev->desc->maxpin; pin++) {
+
+		struct pin_desc *desc;
+
+		desc = pin_desc_get(pctldev, pin);
+		/* Pin space may be sparse */
+		if (desc == NULL)
+			continue;
+
+		seq_printf(s, "pin %d (%s): %s\n", pin,
+			   desc->name ? desc->name : "unnamed",
+			   desc->mux_function ? desc->mux_function
+					      : "UNCLAIMED");
+	}
+
+	return 0;
+}
+
+static int pinmux_hogs_show(struct seq_file *s, void *what)
+{
+	struct pinctrl_dev *pctldev = s->private;
+	struct pinmux_hog *hog;
+
+	seq_puts(s, "Pinmux map hogs held by device\n");
+
+	list_for_each_entry(hog, &pctldev->pinmux_hogs, node)
+		seq_printf(s, "%s\n", hog->map->name);
+
+	return 0;
+}
+
+static int pinmux_show(struct seq_file *s, void *what)
+{
+	struct pinmux *pmx;
+
+	seq_puts(s, "Requested pinmuxes and their maps:\n");
+	list_for_each_entry(pmx, &pinmux_list, node) {
+		struct pinctrl_dev *pctldev = pmx->pctldev;
+		const struct pinmux_ops *pmxops;
+		const struct pinctrl_ops *pctlops;
+		struct pinmux_group *grp;
+
+		if (!pctldev) {
+			seq_puts(s, "NO PIN CONTROLLER DEVICE\n");
+			continue;
+		}
+
+		pmxops = pctldev->desc->pmxops;
+		pctlops = pctldev->desc->pctlops;
+
+		seq_printf(s, "device: %s function: %s (%u),",
+			   pinctrl_dev_get_name(pmx->pctldev),
+			   pmxops->get_function_name(pctldev, pmx->func_selector),
+			   pmx->func_selector);
+
+		seq_printf(s, " groups: [");
+		list_for_each_entry(grp, &pmx->groups, node) {
+			seq_printf(s, " %s (%u)",
+				   pctlops->get_group_name(pctldev, grp->group_selector),
+				   grp->group_selector);
+		}
+		seq_printf(s, " ]");
+
+		seq_printf(s, " users: %u map-> %s\n",
+			   pmx->usecount,
+			   pmx->dev ? dev_name(pmx->dev) : "(system)");
+	}
+
+	return 0;
+}
+
+static int pinmux_maps_show(struct seq_file *s, void *what)
+{
+	int i;
+
+	seq_puts(s, "Pinmux maps:\n");
+
+	for (i = 0; i < pinmux_maps_num; i++) {
+		struct pinmux_map const *map = &pinmux_maps[i];
+
+		seq_printf(s, "%s:\n", map->name);
+		if (map->dev || map->dev_name)
+			seq_printf(s, "  device: %s\n",
+				   map->dev ? dev_name(map->dev) :
+				   map->dev_name);
+		else
+			seq_printf(s, "  SYSTEM MUX\n");
+		seq_printf(s, "  controlling device %s\n",
+			   map->ctrl_dev ? dev_name(map->ctrl_dev) :
+			   map->ctrl_dev_name);
+		seq_printf(s, "  function: %s\n", map->function);
+		seq_printf(s, "  group: %s\n", map->group ? map->group :
+			   "(default)");
+	}
+	return 0;
+}
+
+static int pinmux_functions_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinmux_functions_show, inode->i_private);
+}
+
+static int pinmux_pins_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinmux_pins_show, inode->i_private);
+}
+
+static int pinmux_hogs_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinmux_hogs_show, inode->i_private);
+}
+
+static int pinmux_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinmux_show, NULL);
+}
+
+static int pinmux_maps_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, pinmux_maps_show, NULL);
+}
+
+static const struct file_operations pinmux_functions_ops = {
+	.open		= pinmux_functions_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinmux_pins_ops = {
+	.open		= pinmux_pins_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinmux_hogs_ops = {
+	.open		= pinmux_hogs_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinmux_ops = {
+	.open		= pinmux_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+static const struct file_operations pinmux_maps_ops = {
+	.open		= pinmux_maps_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+};
+
+void pinmux_init_device_debugfs(struct dentry *devroot,
+			 struct pinctrl_dev *pctldev)
+{
+	debugfs_create_file("pinmux-functions", S_IFREG | S_IRUGO,
+			    devroot, pctldev, &pinmux_functions_ops);
+	debugfs_create_file("pinmux-pins", S_IFREG | S_IRUGO,
+			    devroot, pctldev, &pinmux_pins_ops);
+	debugfs_create_file("pinmux-hogs", S_IFREG | S_IRUGO,
+			    devroot, pctldev, &pinmux_hogs_ops);
+}
+
+void pinmux_init_debugfs(struct dentry *subsys_root)
+{
+	debugfs_create_file("pinmuxes", S_IFREG | S_IRUGO,
+			    subsys_root, NULL, &pinmux_ops);
+	debugfs_create_file("pinmux-maps", S_IFREG | S_IRUGO,
+			    subsys_root, NULL, &pinmux_maps_ops);
+}
+
+#endif /* CONFIG_DEBUG_FS */
diff --git a/drivers/pinctrl/pinmux.h b/drivers/pinctrl/pinmux.h
new file mode 100644
index 00000000000000..844500b3331bf8
--- /dev/null
+++ b/drivers/pinctrl/pinmux.h
@@ -0,0 +1,47 @@
+/*
+ * Internal interface between the core pin control system and the
+ * pinmux portions
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ * Based on bits of regulator core, gpio core and clk core
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifdef CONFIG_PINMUX
+
+int pinmux_check_ops(const struct pinmux_ops *ops);
+void pinmux_init_device_debugfs(struct dentry *devroot,
+				struct pinctrl_dev *pctldev);
+void pinmux_init_debugfs(struct dentry *subsys_root);
+int pinmux_hog_maps(struct pinctrl_dev *pctldev);
+void pinmux_unhog_maps(struct pinctrl_dev *pctldev);
+
+#else
+
+static inline int pinmux_check_ops(const struct pinmux_ops *ops)
+{
+	return 0;
+}
+
+static inline void pinmux_init_device_debugfs(struct dentry *devroot,
+					      struct pinctrl_dev *pctldev)
+{
+}
+
+static inline void pinmux_init_debugfs(struct dentry *subsys_root)
+{
+}
+
+static inline int pinmux_hog_maps(struct pinctrl_dev *pctldev)
+{
+	return 0;
+}
+
+static inline void pinmux_unhog_maps(struct pinctrl_dev *pctldev)
+{
+}
+
+#endif
diff --git a/include/linux/pinctrl/machine.h b/include/linux/pinctrl/machine.h
new file mode 100644
index 00000000000000..88863531d862c6
--- /dev/null
+++ b/include/linux/pinctrl/machine.h
@@ -0,0 +1,107 @@
+/*
+ * Machine interface for the pinctrl subsystem.
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ * Based on bits of regulator core, gpio core and clk core
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef __LINUX_PINMUX_MACHINE_H
+#define __LINUX_PINMUX_MACHINE_H
+
+/**
+ * struct pinmux_map - boards/machines shall provide this map for devices
+ * @name: the name of this specific map entry for the particular machine.
+ *	This is the second parameter passed to pinmux_get() when you want
+ *	to have several mappings to the same device
+ * @ctrl_dev: the pin control device to be used by this mapping, may be NULL
+ *	if you provide .ctrl_dev_name instead (this is more common)
+ * @ctrl_dev_name: the name of the device controlling this specific mapping,
+ *	the name must be the same as in your struct device*, may be NULL if
+ *	you provide .ctrl_dev instead
+ * @function: a function in the driver to use for this mapping, the driver
+ *	will lookup the function referenced by this ID on the specified
+ *	pin control device
+ * @group: sometimes a function can map to different pin groups, so this
+ *	selects a certain specific pin group to activate for the function, if
+ *	left as NULL, the first applicable group will be used
+ * @dev: the device using this specific mapping, may be NULL if you provide
+ *	.dev_name instead (this is more common)
+ * @dev_name: the name of the device using this specific mapping, the name
+ *	must be the same as in your struct device*, may be NULL if you
+ *	provide .dev instead
+ * @hog_on_boot: if this is set to true, the pin control subsystem will itself
+ *	hog the mappings as the pinmux device drivers are attached, so this is
+ *	typically used with system maps (mux mappings without an assigned
+ *	device) that you want to get hogged and enabled by default as soon as
+ *	a pinmux device supporting it is registered. These maps will not be
+ *	disabled and put until the system shuts down.
+ */
+struct pinmux_map {
+	const char *name;
+	struct device *ctrl_dev;
+	const char *ctrl_dev_name;
+	const char *function;
+	const char *group;
+	struct device *dev;
+	const char *dev_name;
+	const bool hog_on_boot;
+};
+
+/*
+ * Convenience macro to set a simple map from a certain pin controller and a
+ * certain function to a named device
+ */
+#define PINMUX_MAP(a, b, c, d) \
+	{ .name = a, .ctrl_dev_name = b, .function = c, .dev_name = d }
+
+/*
+ * Convenience macro to map a system function onto a certain pinctrl device.
+ * System functions are not assigned to a particular device.
+ */
+#define PINMUX_MAP_SYS(a, b, c) \
+	{ .name = a, .ctrl_dev_name = b, .function = c }
+
+/*
+ * Convenience macro to map a function onto the primary device pinctrl device
+ * this is especially helpful on systems that have only one pin controller
+ * or need to set up a lot of mappings on the primary controller.
+ */
+#define PINMUX_MAP_PRIMARY(a, b, c) \
+	{ .name = a, .ctrl_dev_name = "pinctrl.0", .function = b, \
+	  .dev_name = c }
+
+/*
+ * Convenience macro to map a system function onto the primary pinctrl device.
+ * System functions are not assigned to a particular device.
+ */
+#define PINMUX_MAP_PRIMARY_SYS(a, b) \
+	{ .name = a, .ctrl_dev_name = "pinctrl.0", .function = b }
+
+/*
+ * Convenience macro to map a system function onto the primary pinctrl device,
+ * to be hogged by the pinmux core until the system shuts down.
+ */
+#define PINMUX_MAP_PRIMARY_SYS_HOG(a, b) \
+	{ .name = a, .ctrl_dev_name = "pinctrl.0", .function = b, \
+	  .hog_on_boot = true }
+
+
+#ifdef CONFIG_PINMUX
+
+extern int pinmux_register_mappings(struct pinmux_map const *map,
+				unsigned num_maps);
+
+#else
+
+static inline int pinmux_register_mappings(struct pinmux_map const *map,
+					   unsigned num_maps)
+{
+	return 0;
+}
+
+#endif /* !CONFIG_PINMUX */
+#endif
diff --git a/include/linux/pinctrl/pinctrl.h b/include/linux/pinctrl/pinctrl.h
new file mode 100644
index 00000000000000..3605e947fa90db
--- /dev/null
+++ b/include/linux/pinctrl/pinctrl.h
@@ -0,0 +1,133 @@
+/*
+ * Interface the pinctrl subsystem
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ * This interface is used in the core to keep track of pins.
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef __LINUX_PINCTRL_PINCTRL_H
+#define __LINUX_PINCTRL_PINCTRL_H
+
+#ifdef CONFIG_PINCTRL
+
+#include <linux/radix-tree.h>
+#include <linux/spinlock.h>
+#include <linux/list.h>
+#include <linux/seq_file.h>
+
+struct pinctrl_dev;
+struct pinmux_ops;
+struct gpio_chip;
+
+/**
+ * struct pinctrl_pin_desc - boards/machines provide information on their
+ * pins, pads or other muxable units in this struct
+ * @number: unique pin number from the global pin number space
+ * @name: a name for this pin
+ */
+struct pinctrl_pin_desc {
+	unsigned number;
+	const char *name;
+};
+
+/* Convenience macro to define a single named or anonymous pin descriptor */
+#define PINCTRL_PIN(a, b) { .number = a, .name = b }
+#define PINCTRL_PIN_ANON(a) { .number = a }
+
+/**
+ * struct pinctrl_gpio_range - each pin controller can provide subranges of
+ * the GPIO number space to be handled by the controller
+ * @node: list node for internal use
+ * @name: a name for the chip in this range
+ * @id: an ID number for the chip in this range
+ * @base: base offset of the GPIO range
+ * @npins: number of pins in the GPIO range, including the base number
+ * @gc: an optional pointer to a gpio_chip
+ */
+struct pinctrl_gpio_range {
+	struct list_head node;
+	const char *name;
+	unsigned int id;
+	unsigned int base;
+	unsigned int npins;
+	struct gpio_chip *gc;
+};
+
+/**
+ * struct pinctrl_ops - global pin control operations, to be implemented by
+ * pin controller drivers.
+ * @list_groups: list the number of selectable named groups available
+ *	in this pinmux driver, the core will begin on 0 and call this
+ *	repeatedly as long as it returns >= 0 to enumerate the groups
+ * @get_group_name: return the group name of the pin group
+ * @get_group_pins: return an array of pins corresponding to a certain
+ *	group selector @pins, and the size of the array in @num_pins
+ * @pin_dbg_show: optional debugfs display hook that will provide per-device
+ *	info for a certain pin in debugfs
+ */
+struct pinctrl_ops {
+	int (*list_groups) (struct pinctrl_dev *pctldev, unsigned selector);
+	const char *(*get_group_name) (struct pinctrl_dev *pctldev,
+				       unsigned selector);
+	int (*get_group_pins) (struct pinctrl_dev *pctldev,
+			       unsigned selector,
+			       const unsigned **pins,
+			       unsigned *num_pins);
+	void (*pin_dbg_show) (struct pinctrl_dev *pctldev, struct seq_file *s,
+			  unsigned offset);
+};
+
+/**
+ * struct pinctrl_desc - pin controller descriptor, register this to pin
+ * control subsystem
+ * @name: name for the pin controller
+ * @pins: an array of pin descriptors describing all the pins handled by
+ *	this pin controller
+ * @npins: number of descriptors in the array, usually just ARRAY_SIZE()
+ *	of the pins field above
+ * @maxpin: since pin spaces may be sparse, there can he "holes" in the
+ *	pin range, this attribute gives the maximum pin number in the
+ *	total range. This should not be lower than npins for example,
+ *	but may be equal to npins if you have no holes in the pin range.
+ * @pctlops: pin control operation vtable, to support global concepts like
+ *	grouping of pins, this is optional.
+ * @pmxops: pinmux operation vtable, if you support pinmuxing in your driver
+ * @owner: module providing the pin controller, used for refcounting
+ */
+struct pinctrl_desc {
+	const char *name;
+	struct pinctrl_pin_desc const *pins;
+	unsigned int npins;
+	unsigned int maxpin;
+	struct pinctrl_ops *pctlops;
+	struct pinmux_ops *pmxops;
+	struct module *owner;
+};
+
+/* External interface to pin controller */
+extern struct pinctrl_dev *pinctrl_register(struct pinctrl_desc *pctldesc,
+				struct device *dev, void *driver_data);
+extern void pinctrl_unregister(struct pinctrl_dev *pctldev);
+extern bool pin_is_valid(struct pinctrl_dev *pctldev, int pin);
+extern void pinctrl_add_gpio_range(struct pinctrl_dev *pctldev,
+				struct pinctrl_gpio_range *range);
+extern void pinctrl_remove_gpio_range(struct pinctrl_dev *pctldev,
+				struct pinctrl_gpio_range *range);
+extern const char *pinctrl_dev_get_name(struct pinctrl_dev *pctldev);
+extern void *pinctrl_dev_get_drvdata(struct pinctrl_dev *pctldev);
+#else
+
+
+/* Sufficiently stupid default function when pinctrl is not in use */
+static inline bool pin_is_valid(struct pinctrl_dev *pctldev, int pin)
+{
+	return pin >= 0;
+}
+
+#endif /* !CONFIG_PINCTRL */
+
+#endif /* __LINUX_PINCTRL_PINCTRL_H */
diff --git a/include/linux/pinctrl/pinmux.h b/include/linux/pinctrl/pinmux.h
new file mode 100644
index 00000000000000..3c430e797efc73
--- /dev/null
+++ b/include/linux/pinctrl/pinmux.h
@@ -0,0 +1,117 @@
+/*
+ * Interface the pinmux subsystem
+ *
+ * Copyright (C) 2011 ST-Ericsson SA
+ * Written on behalf of Linaro for ST-Ericsson
+ * Based on bits of regulator core, gpio core and clk core
+ *
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ *
+ * License terms: GNU General Public License (GPL) version 2
+ */
+#ifndef __LINUX_PINCTRL_PINMUX_H
+#define __LINUX_PINCTRL_PINMUX_H
+
+#include <linux/list.h>
+#include <linux/seq_file.h>
+#include "pinctrl.h"
+
+/* This struct is private to the core and should be regarded as a cookie */
+struct pinmux;
+
+#ifdef CONFIG_PINMUX
+
+struct pinctrl_dev;
+
+/**
+ * struct pinmux_ops - pinmux operations, to be implemented by pin controller
+ * drivers that support pinmuxing
+ * @request: called by the core to see if a certain pin can be made available
+ *	available for muxing. This is called by the core to acquire the pins
+ *	before selecting any actual mux setting across a function. The driver
+ *	is allowed to answer "no" by returning a negative error code
+ * @free: the reverse function of the request() callback, frees a pin after
+ *	being requested
+ * @list_functions: list the number of selectable named functions available
+ *	in this pinmux driver, the core will begin on 0 and call this
+ *	repeatedly as long as it returns >= 0 to enumerate mux settings
+ * @get_function_name: return the function name of the muxing selector,
+ *	called by the core to figure out which mux setting it shall map a
+ *	certain device to
+ * @get_function_groups: return an array of groups names (in turn
+ *	referencing pins) connected to a certain function selector. The group
+ *	name can be used with the generic @pinctrl_ops to retrieve the
+ *	actual pins affected. The applicable groups will be returned in
+ *	@groups and the number of groups in @num_groups
+ * @enable: enable a certain muxing function with a certain pin group. The
+ *	driver does not need to figure out whether enabling this function
+ *	conflicts some other use of the pins in that group, such collisions
+ *	are handled by the pinmux subsystem. The @func_selector selects a
+ *	certain function whereas @group_selector selects a certain set of pins
+ *	to be used. On simple controllers the latter argument may be ignored
+ * @disable: disable a certain muxing selector with a certain pin group
+ * @gpio_request_enable: requests and enables GPIO on a certain pin.
+ *	Implement this only if you can mux every pin individually as GPIO. The
+ *	affected GPIO range is passed along with an offset into that
+ *	specific GPIO range - function selectors and pin groups are orthogonal
+ *	to this, the core will however make sure the pins do not collide
+ */
+struct pinmux_ops {
+	int (*request) (struct pinctrl_dev *pctldev, unsigned offset);
+	int (*free) (struct pinctrl_dev *pctldev, unsigned offset);
+	int (*list_functions) (struct pinctrl_dev *pctldev, unsigned selector);
+	const char *(*get_function_name) (struct pinctrl_dev *pctldev,
+					  unsigned selector);
+	int (*get_function_groups) (struct pinctrl_dev *pctldev,
+				  unsigned selector,
+				  const char * const **groups,
+				  unsigned * const num_groups);
+	int (*enable) (struct pinctrl_dev *pctldev, unsigned func_selector,
+		       unsigned group_selector);
+	void (*disable) (struct pinctrl_dev *pctldev, unsigned func_selector,
+			 unsigned group_selector);
+	int (*gpio_request_enable) (struct pinctrl_dev *pctldev,
+				    struct pinctrl_gpio_range *range,
+				    unsigned offset);
+};
+
+/* External interface to pinmux */
+extern int pinmux_request_gpio(unsigned gpio);
+extern void pinmux_free_gpio(unsigned gpio);
+extern struct pinmux * __must_check pinmux_get(struct device *dev, const char *name);
+extern void pinmux_put(struct pinmux *pmx);
+extern int pinmux_enable(struct pinmux *pmx);
+extern void pinmux_disable(struct pinmux *pmx);
+
+#else /* !CONFIG_PINMUX */
+
+static inline int pinmux_request_gpio(unsigned gpio)
+{
+	return 0;
+}
+
+static inline void pinmux_free_gpio(unsigned gpio)
+{
+}
+
+static inline struct pinmux * __must_check pinmux_get(struct device *dev, const char *name)
+{
+	return NULL;
+}
+
+static inline void pinmux_put(struct pinmux *pmx)
+{
+}
+
+static inline int pinmux_enable(struct pinmux *pmx)
+{
+	return 0;
+}
+
+static inline void pinmux_disable(struct pinmux *pmx)
+{
+}
+
+#endif /* CONFIG_PINMUX */
+
+#endif /* __LINUX_PINCTRL_PINMUX_H */