By default, the driver core only enforces dependencies between devices that are borne out of a parent/child relationship within the device hierarchy: When suspending, resuming or shutting down the system, devices are ordered based on this relationship, i.e. children are always suspended before their parent, and the parent is always resumed before its children.
Sometimes there is a need to represent device dependencies beyond the mere parent/child relationship, e.g. between siblings, and have the driver core automatically take care of them.
Secondly, the driver core by default does not enforce any driver presence dependencies, i.e. that one device must be bound to a driver before another one can probe or function correctly.
Often these two dependency types come together, so a device depends on another one both with regards to driver presence and with regards to suspend/resume and shutdown ordering.
Device links allow representation of such dependencies in the driver core.
In its standard form, a device link combines both dependency types: It guarantees correct suspend/resume and shutdown ordering between a “supplier” device and its “consumer” devices, and it guarantees driver presence on the supplier. The consumer devices are not probed before the supplier is bound to a driver, and they’re unbound before the supplier is unbound.
When driver presence on the supplier is irrelevant and only correct
suspend/resume and shutdown ordering is needed, the device link may
simply be set up with the
DL_FLAG_STATELESS flag. In other words,
enforcing driver presence on the supplier is optional.
Another optional feature is runtime PM integration: By setting the
DL_FLAG_PM_RUNTIME flag on addition of the device link, the PM core
is instructed to runtime resume the supplier and keep it active
whenever and for as long as the consumer is runtime resumed.
The earliest point in time when device links can be added is after
device_add() has been called for the supplier and
device_initialize() has been called for the consumer.
It is legal to add them later, but care must be taken that the system
remains in a consistent state: E.g. a device link cannot be added in
the midst of a suspend/resume transition, so either commencement of
such a transition needs to be prevented with
or the device link needs to be added from a function which is guaranteed
not to run in parallel to a suspend/resume transition, such as from a
->probe callback or a boot-time PCI quirk.
Another example for an inconsistent state would be a device link that
represents a driver presence dependency, yet is added from the consumer’s
->probe callback while the supplier hasn’t probed yet: Had the driver
core known about the device link earlier, it wouldn’t have probed the
consumer in the first place. The onus is thus on the consumer to check
presence of the supplier after adding the link, and defer probing on
If a device link is added in the
->probe callback of the supplier or
consumer driver, it is typically deleted in its
->remove callback for
symmetry. That way, if the driver is compiled as a module, the device
link is added on module load and orderly deleted on unload. The same
restrictions that apply to device link addition (e.g. exclusion of a
parallel suspend/resume transition) apply equally to deletion.
Several flags may be specified on device link addition, two of which
have already been mentioned above:
DL_FLAG_STATELESS to express that no
driver presence dependency is needed (but only correct suspend/resume and
shutdown ordering) and
DL_FLAG_PM_RUNTIME to express that runtime PM
integration is desired.
Two other flags are specifically targeted at use cases where the device
link is added from the consumer’s
can be specified to runtime resume the supplier upon addition of the
DL_FLAG_AUTOREMOVE causes the device link to be automatically
purged when the consumer fails to probe or later unbinds. This obviates
the need to explicitly delete the link in the
->remove callback or in
the error path of the
Driver authors should be aware that a driver presence dependency (i.e. when
DL_FLAG_STATELESS is not specified on link addition) may cause probing of
the consumer to be deferred indefinitely. This can become a problem if the
consumer is required to probe before a certain initcall level is reached.
Worse, if the supplier driver is blacklisted or missing, the consumer will
never be probed.
Sometimes drivers depend on optional resources. They are able to operate in a degraded mode (reduced feature set or performance) when those resources are not present. An example is an SPI controller that can use a DMA engine or work in PIO mode. The controller can determine presence of the optional resources at probe time but on non-presence there is no way to know whether they will become available in the near future (due to a supplier driver probing) or never. Consequently it cannot be determined whether to defer probing or not. It would be possible to notify drivers when optional resources become available after probing, but it would come at a high cost for drivers as switching between modes of operation at runtime based on the availability of such resources would be much more complex than a mechanism based on probe deferral. In any case optional resources are beyond the scope of device links.
An MMU device exists alongside a busmaster device, both are in the same power domain. The MMU implements DMA address translation for the busmaster device and shall be runtime resumed and kept active whenever and as long as the busmaster device is active. The busmaster device’s driver shall not bind before the MMU is bound. To achieve this, a device link with runtime PM integration is added from the busmaster device (consumer) to the MMU device (supplier). The effect with regards to runtime PM is the same as if the MMU was the parent of the master device.
The fact that both devices share the same power domain would normally suggest usage of a
struct generic_pm_domain, however these are not independent devices that happen to share a power switch, but rather the MMU device serves the busmaster device and is useless without it. A device link creates a synthetic hierarchical relationship between the devices and is thus more apt.
A Thunderbolt host controller comprises a number of PCIe hotplug ports and an NHI device to manage the PCIe switch. On resume from system sleep, the NHI device needs to re-establish PCI tunnels to attached devices before the hotplug ports can resume. If the hotplug ports were children of the NHI, this resume order would automatically be enforced by the PM core, but unfortunately they’re aunts. The solution is to add device links from the hotplug ports (consumers) to the NHI device (supplier). A driver presence dependency is not necessary for this use case.
Discrete GPUs in hybrid graphics laptops often feature an HDA controller for HDMI/DP audio. In the device hierarchy the HDA controller is a sibling of the VGA device, yet both share the same power domain and the HDA controller is only ever needed when an HDMI/DP display is attached to the VGA device. A device link from the HDA controller (consumer) to the VGA device (supplier) aptly represents this relationship.
ACPI allows definition of a device start order by way of _DEP objects. A classical example is when ACPI power management methods on one device are implemented in terms of I2C accesses and require a specific I2C controller to be present and functional for the power management of the device in question to work.
In some SoCs a functional dependency exists from display, video codec and video processing IP cores on transparent memory access IP cores that handle burst access and compression/decompression.
struct dev_pm_domaincan be used to override the bus, class or device type callbacks. It is intended for devices sharing a single on/off switch, however it does not guarantee a specific suspend/resume ordering, this needs to be implemented separately. It also does not by itself track the runtime PM status of the involved devices and turn off the power switch only when all of them are runtime suspended. Furthermore it cannot be used to enforce a specific shutdown ordering or a driver presence dependency.
struct generic_pm_domainis a lot more heavyweight than a device link and does not allow for shutdown ordering or driver presence dependencies. It also cannot be used on ACPI systems.
The device hierarchy, which – as the name implies – is a tree, becomes a directed acyclic graph once device links are added.
Ordering of these devices during suspend/resume is determined by the dpm_list. During shutdown it is determined by the devices_kset. With no device links present, the two lists are a flattened, one-dimensional representations of the device tree such that a device is placed behind all its ancestors. That is achieved by traversing the ACPI namespace or OpenFirmware device tree top-down and appending devices to the lists as they are discovered.
Once device links are added, the lists need to satisfy the additional
constraint that a device is placed behind all its suppliers, recursively.
To ensure this, upon addition of the device link the consumer and the
entire sub-graph below it (all children and consumers of the consumer)
are moved to the end of the list. (Call to
To prevent introduction of dependency loops into the graph, it is
verified upon device link addition that the supplier is not dependent
on the consumer or any children or consumers of the consumer.
If that constraint is violated,
device_link_add() will return
NULL and a
WARNING will be logged.
Notably this also prevents the addition of a device link from a parent device to a child. However the converse is allowed, i.e. a device link from a child to a parent. Since the driver core already guarantees correct suspend/resume and shutdown ordering between parent and child, such a device link only makes sense if a driver presence dependency is needed on top of that. In this case driver authors should weigh carefully if a device link is at all the right tool for the purpose. A more suitable approach might be to simply use deferred probing or add a device flag causing the parent driver to be probed before the child one.
Device link states.
- The presence of the drivers is not being tracked.
- None of the supplier/consumer drivers is present.
- The supplier driver is present, but the consumer is not.
- The consumer is probing (supplier driver present).
- Both the supplier and consumer drivers are present.
- The supplier driver is unbinding.
.=============================. | | v | DORMANT <=> AVAILABLE <=> CONSUMER_PROBE => ACTIVE ^ | | | '============ SUPPLIER_UNBIND <============'
- The initial state of a device link is automatically determined by
device_link_add()based on the driver presence on the supplier and consumer. If the link is created before any devices are probed, it is set to
- When a supplier device is bound to a driver, links to its consumers
DL_STATE_AVAILABLE. (Call to
- Before a consumer device is probed, presence of supplier drivers is
verified by checking that links to suppliers are in
DL_STATE_AVAILABLEstate. The state of the links is updated to
DL_STATE_CONSUMER_PROBE. (Call to
really_probe().) This prevents the supplier from unbinding. (Call to
- If the probe fails, links to suppliers revert back to
DL_STATE_AVAILABLE. (Call to
- If the probe succeeds, links to suppliers progress to
DL_STATE_ACTIVE. (Call to
- When the consumer’s driver is later on removed, links to suppliers revert
DL_STATE_AVAILABLE. (Call to
device_links_driver_cleanup(), which in turn is called from
- Before a supplier’s driver is removed, links to consumers that are not
bound to a driver are updated to
DL_STATE_SUPPLIER_UNBIND. (Call to
__device_release_driver().) This prevents the consumers from binding. (Call to
really_probe().) Consumers that are bound are freed from their driver; consumers that are probing are waited for until they are done. (Call to
__device_release_driver().) Once all links to consumers are in
DL_STATE_SUPPLIER_UNBINDstate, the supplier driver is released and the links revert to
DL_STATE_DORMANT. (Call to
struct device_link *
device_link_add(struct device * consumer, struct device * supplier, u32 flags)¶
Create a link between two devices.
struct device * consumer
- Consumer end of the link.
struct device * supplier
- Supplier end of the link.
- Link flags.
The caller is responsible for the proper synchronization of the link creation with runtime PM. First, setting the DL_FLAG_PM_RUNTIME flag will cause the runtime PM framework to take the link into account. Second, if the DL_FLAG_RPM_ACTIVE flag is set in addition to it, the supplier devices will be forced into the active metastate and reference-counted upon the creation of the link. If DL_FLAG_PM_RUNTIME is not set, DL_FLAG_RPM_ACTIVE will be ignored.
If the DL_FLAG_AUTOREMOVE is set, the link will be removed automatically when the consumer device driver unbinds from it. The combination of both DL_FLAG_AUTOREMOVE and DL_FLAG_STATELESS set is invalid and will cause NULL to be returned.
A side effect of the link creation is re-ordering of dpm_list and the devices_kset list by moving the consumer device and all devices depending on it to the ends of these lists (that does not happen to devices that have not been registered when this function is called).
The supplier device is required to be registered when this function is called and NULL will be returned if that is not the case. The consumer device need not be registered, however.
device_link_del(struct device_link * link)¶
Delete a link between two devices.
struct device_link * link
- Device link to delete.
The caller must ensure proper synchronization of this function with runtime
PM. If the link was added multiple times, it needs to be deleted as often.
Care is required for hotplugged devices: Their links are purged on removal
device_link_del() is then no longer allowed.