Fujitsu Uncore Performance Monitoring Unit (PMU)

This driver supports the Uncore MAC PMUs and the Uncore PCI PMUs found in Fujitsu chips. Each MAC PMU on these chips is exposed as a uncore perf PMU with device name mac_iod<iod>_mac<mac>_ch<ch>. And each PCI PMU on these chips is exposed as a uncore perf PMU with device name pci_iod<iod>_pci<pci>.

The driver provides a description of its available events and configuration options in sysfs, see /sys/bus/event_sources/devices/mac_iod<iod>_mac<mac>_ch<ch>/ and /sys/bus/event_sources/devices/pci_iod<iod>_pci<pci>/. This driver exports:

  • formats, used by perf user space and other tools to configure events

  • events, used by perf user space and other tools to create events symbolically, e.g.:

    perf stat -a -e mac_iod0_mac0_ch0/event=0x21/ ls
perf stat -a -e pci_iod0_pci0/event=0x24/ ls

  • cpumask, used by perf user space and other tools to know on which CPUs to open the events

This driver supports the following events for MAC:

  • cycles This event counts MAC cycles at MAC frequency.

  • read-count This event counts the number of read requests to MAC.

  • read-count-request This event counts the number of read requests including retry to MAC.

  • read-count-return This event counts the number of responses to read requests to MAC.

  • read-count-request-pftgt This event counts the number of read requests including retry with PFTGT flag.

  • read-count-request-normal This event counts the number of read requests including retry without PFTGT flag.

  • read-count-return-pftgt-hit This event counts the number of responses to read requests which hit the PFTGT buffer.

  • read-count-return-pftgt-miss This event counts the number of responses to read requests which miss the PFTGT buffer.

  • read-wait This event counts outstanding read requests issued by DDR memory controller per cycle.

  • write-count This event counts the number of write requests to MAC (including zero write, full write, partial write, write cancel).

  • write-count-write This event counts the number of full write requests to MAC (not including zero write).

  • write-count-pwrite This event counts the number of partial write requests to MAC.

  • memory-read-count This event counts the number of read requests from MAC to memory.

  • memory-write-count This event counts the number of full write requests from MAC to memory.

  • memory-pwrite-count This event counts the number of partial write requests from MAC to memory.

  • ea-mac This event counts energy consumption of MAC.

  • ea-memory This event counts energy consumption of memory.

  • ea-memory-mac-write This event counts the number of write requests from MAC to memory.

  • ea-ha This event counts energy consumption of HA.

    ‘ea’ is the abbreviation for ‘Energy Analyzer’.

Examples for use with perf:

perf stat -e mac_iod0_mac0_ch0/ea-mac/ ls

And, this driver supports the following events for PCI:

  • pci-port0-cycles This event counts PCI cycles at PCI frequency in port0.

  • pci-port0-read-count This event counts read transactions for data transfer in port0.

  • pci-port0-read-count-bus This event counts read transactions for bus usage in port0.

  • pci-port0-write-count This event counts write transactions for data transfer in port0.

  • pci-port0-write-count-bus This event counts write transactions for bus usage in port0.

  • pci-port1-cycles This event counts PCI cycles at PCI frequency in port1.

  • pci-port1-read-count This event counts read transactions for data transfer in port1.

  • pci-port1-read-count-bus This event counts read transactions for bus usage in port1.

  • pci-port1-write-count This event counts write transactions for data transfer in port1.

  • pci-port1-write-count-bus This event counts write transactions for bus usage in port1.

  • ea-pci This event counts energy consumption of PCI.

    ‘ea’ is the abbreviation for ‘Energy Analyzer’.

Examples for use with perf:

perf stat -e pci_iod0_pci0/ea-pci/ ls

Given that these are uncore PMUs the driver does not support sampling, therefore “perf record” will not work. Per-task perf sessions are not supported.