1 files changed, 125 insertions, 0 deletions
diff --git a/Documentation/userspace-api/gpio/gpio-get-linehandle-ioctl.rst b/Documentation/userspace-api/gpio/gpio-get-linehandle-ioctl.rst
new file mode 100644
index 0000000000000..9112a9d31174f
--- /dev/null
+++ b/Documentation/userspace-api/gpio/gpio-get-linehandle-ioctl.rst
@@ -0,0 +1,125 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+.. _GPIO_GET_LINEHANDLE_IOCTL:
+
+*************************
+GPIO_GET_LINEHANDLE_IOCTL
+*************************
+
+.. warning::
+    This ioctl is part of chardev_v1.rst and is obsoleted by
+    gpio-v2-get-line-ioctl.rst.
+
+Name
+====
+
+GPIO_GET_LINEHANDLE_IOCTL - Request a line or lines from the kernel.
+
+Synopsis
+========
+
+.. c:macro:: GPIO_GET_LINEHANDLE_IOCTL
+
+``int ioctl(int chip_fd, GPIO_GET_LINEHANDLE_IOCTL, struct gpiohandle_request *request)``
+
+Arguments
+=========
+
+``chip_fd``
+    The file descriptor of the GPIO character device returned by `open()`.
+
+``request``
+    The :c:type:`handle_request<gpiohandle_request>` specifying the lines to
+    request and their configuration.
+
+Description
+===========
+
+Request a line or lines from the kernel.
+
+While multiple lines may be requested, the same configuration applies to all
+lines in the request.
+
+On success, the requesting process is granted exclusive access to the line
+value and write access to the line configuration.
+
+The state of a line, including the value of output lines, is guaranteed to
+remain as requested until the returned file descriptor is closed. Once the
+file descriptor is closed, the state of the line becomes uncontrolled from
+the userspace perspective, and may revert to its default state.
+
+Requesting a line already in use is an error (**EBUSY**).
+
+Closing the ``chip_fd`` has no effect on existing line handles.
+
+.. _gpio-get-linehandle-config-rules:
+
+Configuration Rules
+-------------------
+
+The following configuration rules apply:
+
+The direction flags, ``GPIOHANDLE_REQUEST_INPUT`` and
+``GPIOHANDLE_REQUEST_OUTPUT``, cannot be combined. If neither are set then the
+only other flag that may be set is ``GPIOHANDLE_REQUEST_ACTIVE_LOW`` and the
+line is requested "as-is" to allow reading of the line value without altering
+the electrical configuration.
+
+The drive flags, ``GPIOHANDLE_REQUEST_OPEN_xxx``, require the
+``GPIOHANDLE_REQUEST_OUTPUT`` to be set.
+Only one drive flag may be set.
+If none are set then the line is assumed push-pull.
+
+Only one bias flag, ``GPIOHANDLE_REQUEST_BIAS_xxx``, may be set, and
+it requires a direction flag to also be set.
+If no bias flags are set then the bias configuration is not changed.
+
+Requesting an invalid configuration is an error (**EINVAL**).
+
+
+.. _gpio-get-linehandle-config-support:
+
+Configuration Support
+---------------------
+
+Where the requested configuration is not directly supported by the underlying
+hardware and driver, the kernel applies one of these approaches:
+
+ - reject the request
+ - emulate the feature in software
+ - treat the feature as best effort
+
+The approach applied depends on whether the feature can reasonably be emulated
+in software, and the impact on the hardware and userspace if the feature is not
+supported.
+The approach applied for each feature is as follows:
+
+==============   ===========
+Feature          Approach
+==============   ===========
+Bias             best effort
+Direction        reject
+Drive            emulate
+==============   ===========
+
+Bias is treated as best effort to allow userspace to apply the same
+configuration for platforms that support internal bias as those that require
+external bias.
+Worst case the line floats rather than being biased as expected.
+
+Drive is emulated by switching the line to an input when the line should not
+be driven.
+
+In all cases, the configuration reported by gpio-get-lineinfo-ioctl.rst
+is the requested configuration, not the resulting hardware configuration.
+Userspace cannot determine if a feature is supported in hardware, is
+emulated, or is best effort.
+
+Return Value
+============
+
+On success 0 and the :c:type:`request.fd<gpiohandle_request>` contains the
+file descriptor for the request.
+
+On error -1 and the ``errno`` variable is set appropriately.
+Common error codes are described in error-codes.rst.