Merge 6.8-rc6 into tty-next

We need the tty/serial fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

3 files changed, 38 insertions, 34 deletions

diff --git a/drivers/tty/hvc/Kconfig b/drivers/tty/hvc/Kconfig
index 6e05c5c7bca1a..c2a4e88b328f3 100644
--- a/drivers/tty/hvc/Kconfig
+++ b/drivers/tty/hvc/Kconfig
@@ -108,13 +108,15 @@ config HVC_DCC_SERIALIZE_SMP
 
 config HVC_RISCV_SBI
 	bool "RISC-V SBI console support"
-	depends on RISCV_SBI
+	depends on RISCV_SBI && NONPORTABLE
 	select HVC_DRIVER
 	help
 	  This enables support for console output via RISC-V SBI calls, which
-	  is normally used only during boot to output printk.
+	  is normally used only during boot to output printk.  This driver
+	  conflicts with real console drivers and should not be enabled on
+	  systems that directly access the console.
 
-	  If you don't know what do to here, say Y.
+	  If you don't know what do to here, say N.
 
 config HVCS
 	tristate "IBM Hypervisor Virtual Console Server support"
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c
index fccec1698a541..cf2c890a560f0 100644
--- a/drivers/tty/serial/amba-pl011.c
+++ b/drivers/tty/serial/amba-pl011.c
@@ -1339,11 +1339,41 @@ static void pl011_start_tx_pio(struct uart_amba_port *uap)
 	}
 }
 
+static void pl011_rs485_tx_start(struct uart_amba_port *uap)
+{
+	struct uart_port *port = &uap->port;
+	u32 cr;
+
+	/* Enable transmitter */
+	cr = pl011_read(uap, REG_CR);
+	cr |= UART011_CR_TXE;
+
+	/* Disable receiver if half-duplex */
+	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
+		cr &= ~UART011_CR_RXE;
+
+	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
+		cr &= ~UART011_CR_RTS;
+	else
+		cr |= UART011_CR_RTS;
+
+	pl011_write(cr, uap, REG_CR);
+
+	if (port->rs485.delay_rts_before_send)
+		mdelay(port->rs485.delay_rts_before_send);
+
+	uap->rs485_tx_started = true;
+}
+
 static void pl011_start_tx(struct uart_port *port)
 {
 	struct uart_amba_port *uap =
 	    container_of(port, struct uart_amba_port, port);
 
+	if ((uap->port.rs485.flags & SER_RS485_ENABLED) &&
+	    !uap->rs485_tx_started)
+		pl011_rs485_tx_start(uap);
+
 	if (!pl011_dma_tx_start(uap))
 		pl011_start_tx_pio(uap);
 }
@@ -1424,42 +1454,12 @@ static bool pl011_tx_char(struct uart_amba_port *uap, unsigned char c,
 	return true;
 }
 
-static void pl011_rs485_tx_start(struct uart_amba_port *uap)
-{
-	struct uart_port *port = &uap->port;
-	u32 cr;
-
-	/* Enable transmitter */
-	cr = pl011_read(uap, REG_CR);
-	cr |= UART011_CR_TXE;
-
-	/* Disable receiver if half-duplex */
-	if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
-		cr &= ~UART011_CR_RXE;
-
-	if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
-		cr &= ~UART011_CR_RTS;
-	else
-		cr |= UART011_CR_RTS;
-
-	pl011_write(cr, uap, REG_CR);
-
-	if (port->rs485.delay_rts_before_send)
-		mdelay(port->rs485.delay_rts_before_send);
-
-	uap->rs485_tx_started = true;
-}
-
 /* Returns true if tx interrupts have to be (kept) enabled  */
 static bool pl011_tx_chars(struct uart_amba_port *uap, bool from_irq)
 {
 	struct circ_buf *xmit = &uap->port.state->xmit;
 	int count = uap->fifosize >> 1;
 
-	if ((uap->port.rs485.flags & SER_RS485_ENABLED) &&
-	    !uap->rs485_tx_started)
-		pl011_rs485_tx_start(uap);
-
 	if (uap->port.x_char) {
 		if (!pl011_tx_char(uap, uap->port.x_char, from_irq))
 			return true;
diff --git a/drivers/tty/serial/stm32-usart.c b/drivers/tty/serial/stm32-usart.c
index 3cbb498c6ea68..58d169e5c1db0 100644
--- a/drivers/tty/serial/stm32-usart.c
+++ b/drivers/tty/serial/stm32-usart.c
@@ -255,7 +255,9 @@ static int stm32_usart_config_rs485(struct uart_port *port, struct ktermios *ter
 		writel_relaxed(cr3, port->membase + ofs->cr3);
 		writel_relaxed(cr1, port->membase + ofs->cr1);
 
-		rs485conf->flags |= SER_RS485_RX_DURING_TX;
+		if (!port->rs485_rx_during_tx_gpio)
+			rs485conf->flags |= SER_RS485_RX_DURING_TX;
+
 	} else {
 		stm32_usart_clr_bits(port, ofs->cr3,
 				     USART_CR3_DEM | USART_CR3_DEP);