diff options
| author | Yann Sionneau <ysionneau@kalray.eu> | 2023-09-11 16:07:49 +0200 |
|---|---|---|
| committer | Wolfram Sang <wsa@kernel.org> | 2023-09-19 21:57:11 +0200 |
| commit | 2409205acd3c7c877f3d0080cac6a5feb3358f83 (patch) | |
| tree | 779312359899d099411f5a5bc87cc62507bf79b2 /drivers/i2c/busses | |
| parent | 3914784553f68c931fc666dbe7e86fe881aada38 (diff) | |
| download | linux-2409205acd3c7c877f3d0080cac6a5feb3358f83.tar.gz | |
i2c: designware: fix __i2c_dw_disable() in case master is holding SCL low
The DesignWare IP can be synthesized with the IC_EMPTYFIFO_HOLD_MASTER_EN
parameter.
In this case, when the TX FIFO gets empty and the last command didn't have
the STOP bit (IC_DATA_CMD[9]), the controller will hold SCL low until
a new command is pushed into the TX FIFO or the transfer is aborted.
When the controller is holding SCL low, it cannot be disabled.
The transfer must first be aborted.
Also, the bus recovery won't work because SCL is held low by the master.
Check if the master is holding SCL low in __i2c_dw_disable() before trying
to disable the controller. If SCL is held low, an abort is initiated.
When the abort is done, then proceed with disabling the controller.
This whole situation can happen for instance during SMBus read data block
if the slave just responds with "byte count == 0".
This puts the driver in an unrecoverable state, because the controller is
holding SCL low and the current __i2c_dw_disable() procedure is not
working. In this situation only a SoC reset can fix the i2c bus.
Co-developed-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Jonathan Borne <jborne@kalray.eu>
Signed-off-by: Yann Sionneau <ysionneau@kalray.eu>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Diffstat (limited to 'drivers/i2c/busses')
| -rw-r--r-- | drivers/i2c/busses/i2c-designware-common.c | 17 | ||||
| -rw-r--r-- | drivers/i2c/busses/i2c-designware-core.h | 3 |
2 files changed, 20 insertions, 0 deletions
diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c index cdd8c67d912986..affcfb243f0f52 100644 --- a/drivers/i2c/busses/i2c-designware-common.c +++ b/drivers/i2c/busses/i2c-designware-common.c @@ -441,8 +441,25 @@ err_release_lock: void __i2c_dw_disable(struct dw_i2c_dev *dev) { + unsigned int raw_intr_stats; + unsigned int enable; int timeout = 100; + bool abort_needed; unsigned int status; + int ret; + + regmap_read(dev->map, DW_IC_RAW_INTR_STAT, &raw_intr_stats); + regmap_read(dev->map, DW_IC_ENABLE, &enable); + + abort_needed = raw_intr_stats & DW_IC_INTR_MST_ON_HOLD; + if (abort_needed) { + regmap_write(dev->map, DW_IC_ENABLE, enable | DW_IC_ENABLE_ABORT); + ret = regmap_read_poll_timeout(dev->map, DW_IC_ENABLE, enable, + !(enable & DW_IC_ENABLE_ABORT), 10, + 100); + if (ret) + dev_err(dev->dev, "timeout while trying to abort current transfer\n"); + } do { __i2c_dw_disable_nowait(dev); diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index cf4f684f535664..a7f6f3eafad7dd 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -98,6 +98,7 @@ #define DW_IC_INTR_START_DET BIT(10) #define DW_IC_INTR_GEN_CALL BIT(11) #define DW_IC_INTR_RESTART_DET BIT(12) +#define DW_IC_INTR_MST_ON_HOLD BIT(13) #define DW_IC_INTR_DEFAULT_MASK (DW_IC_INTR_RX_FULL | \ DW_IC_INTR_TX_ABRT | \ @@ -108,6 +109,8 @@ DW_IC_INTR_RX_UNDER | \ DW_IC_INTR_RD_REQ) +#define DW_IC_ENABLE_ABORT BIT(1) + #define DW_IC_STATUS_ACTIVITY BIT(0) #define DW_IC_STATUS_TFE BIT(2) #define DW_IC_STATUS_RFNE BIT(3) |