hwmon: Add support for Amphenol ChipCap 2

The Amphenol ChipCap 2 is a capacitive polymer humidity and temperature
sensor with an integrated EEPROM and minimum/maximum humidity alarms.

All device variants offer an I2C interface and depending on the part
number, two different output modes:
- CC2D: digital output
- CC2A: analog (PDM) output

This driver adds support for the digital variant (CC2D part numbers),
which includes the following part numbers:
- non-sleep measurement mode (CC2D23, CC2D25, CC2D33, CC2D35)
- sleep measurement mode (CC2D23S, CC2D25S, CC2D33S, CC2D35S)

The Chipcap 2 EEPROM can be accessed to configure a series of parameters
like the minimum/maximum humidity alarm threshold and hysteresis. The
EEPROM is only accessible in the command window after a power-on reset.
The default window lasts 10 ms if no Start_CM command is sent. After the
command window is finished (either after the mentioned timeout of after
a Start_NOM command is sent), the device enters the normal operation
mode and makes a first measurement automatically.

Unfortunately, the device does not provide any hardware or software
reset and therefore the driver must trigger power cycles to enter the
command mode. A dedicated, external regulator is required for that.

This driver keeps the device off until a measurement or access to the
EEPROM is required, making use of the first automatic measurement to
avoid different code paths for sleep and non-sleep devices.

The minimum and maximum humidity alarms are configured with two
registers per alarm: one stores the alarm threshold and the other one
keeps the value that turns off the alarm. The alarm signals are only
updated when a measurement is carried out.

Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240130-topic-chipcap2-v6-5-260bea05cf9b@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

2 files changed, 74 insertions, 0 deletions

diff --git a/Documentation/hwmon/chipcap2.rst b/Documentation/hwmon/chipcap2.rst
new file mode 100644
index 0000000000000..dc165becc64cf
--- /dev/null
+++ b/Documentation/hwmon/chipcap2.rst
@@ -0,0 +1,73 @@
+.. SPDX-License-Identifier: GPL-2.0-or-later
+
+Kernel driver ChipCap2
+======================
+
+Supported chips:
+
+  * Amphenol CC2D23, CC2D23S, CC2D25, CC2D25S, CC2D33, CC2D33S, CC2D35, CC2D35S
+
+    Prefix: 'chipcap2'
+
+    Addresses scanned: -
+
+    Datasheet: https://www.amphenol-sensors.com/en/telaire/humidity/527-humidity-sensors/3095-chipcap-2
+
+Author:
+
+  - Javier Carrasco <javier.carrasco.cruz@gmail.com>
+
+Description
+-----------
+
+This driver implements support for the Amphenol ChipCap 2, a humidity and
+temperature chip family. Temperature is measured in milli degrees celsius,
+relative humidity is expressed as a per cent mille. The measurement ranges
+are the following:
+
+  - Relative humidity: 0 to 100000 pcm (14-bit resolution)
+  - Temperature: -40000 to +125000 m°C (14-bit resolution)
+
+The device communicates with the I2C protocol and uses the I2C address 0x28
+by default.
+
+Depending on the hardware configuration, up to two humidity alarms to control
+minimum and maximum values are provided. Their thresholds and hystersis can be
+configured via sysfs.
+
+Thresholds and hysteris must be provided as a per cent mille. These values
+might be truncated to match the 14-bit device resolution (6.1 pcm/LSB)
+
+Known Issues
+------------
+
+The driver does not support I2C address and command window length modification.
+
+sysfs-Interface
+---------------
+
+The following list includes the sysfs attributes that the driver always provides,
+their permissions and a short description:
+
+=============================== ======= ========================================
+Name                            Perm    Description
+=============================== ======= ========================================
+temp1_input:                    RO      temperature input
+humidity1_input:                RO      humidity input
+=============================== ======= ========================================
+
+The following list includes the sysfs attributes that the driver may provide
+depending on the hardware configuration:
+
+=============================== ======= ========================================
+Name                            Perm    Description
+=============================== ======= ========================================
+humidity1_min:                  RW      humidity low limit. Measurements under
+                                        this limit trigger a humidity low alarm
+humidity1_max:                  RW      humidity high limit. Measurements above
+                                        this limit trigger a humidity high alarm
+humidity1_min_hyst:             RW      humidity low hystersis
+humidity1_max_hyst:             RW      humidity high hystersis
+humidity1_min_alarm:            RO      humidity low alarm indicator
+humidity1_max_alarm:            RO      humidity high alarm indicator
+=============================== ======= ========================================
diff --git a/Documentation/hwmon/index.rst b/Documentation/hwmon/index.rst
index 9ac087dd3e78d..0d12254c0f9ee 100644
--- a/Documentation/hwmon/index.rst
+++ b/Documentation/hwmon/index.rst
@@ -51,6 +51,7 @@ Hardware Monitoring Kernel Drivers
    bel-pfe
    bpa-rs600
    bt1-pvt
+   chipcap2
    coretemp
    corsair-cpro
    corsair-psu