Update ath5k driver to newest version

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
author: Hauke Mehrtens <hauke@hauke-m.de> 2008-09-05 18:40:23 +0200
committer: Luis R. Rodriguez <lrodriguez@atheros.com> 2008-09-05 10:53:48 -0700
commit: e3dabd8797267e70bf6ab72ced274855489b1035 (patch)
tree: 00301a1b4486db212835d45ec026054d61296d90
parent: 884c73f54a2d10a49aa166daf0daa76b4b8d60d5 (diff)
download: compat-wireless-2.6-old-e3dabd8797267e70bf6ab72ced274855489b1035.tar.gz
9 files changed, 1318 insertions, 812 deletions
diff --git a/drivers/net/wireless/ath5k/ath5k.h b/drivers/net/wireless/ath5k/ath5k.h
index ba35c30..c1b4978 100644
--- a/drivers/net/wireless/ath5k/ath5k.h
+++ b/drivers/net/wireless/ath5k/ath5k.h
@@ -186,11 +186,13 @@ struct ath5k_srev_name {
 #define AR5K_SREV_RAD_2111	0x20
 #define AR5K_SREV_RAD_5112	0x30
 #define AR5K_SREV_RAD_5112A	0x35
+#define	AR5K_SREV_RAD_5112B	0x36
 #define AR5K_SREV_RAD_2112	0x40
 #define AR5K_SREV_RAD_2112A	0x45
-#define AR5K_SREV_RAD_SC0	0x56	/* Found on 2413/2414 */
-#define AR5K_SREV_RAD_SC1	0x63	/* Found on 5413/5414 */
-#define AR5K_SREV_RAD_SC2	0xa2	/* Found on 2424-5/5424 */
+#define	AR5K_SREV_RAD_2112B	0x46
+#define AR5K_SREV_RAD_SC0	0x50	/* Found on 2413/2414 */
+#define AR5K_SREV_RAD_SC1	0x60	/* Found on 5413/5414 */
+#define AR5K_SREV_RAD_SC2	0xa0	/* Found on 2424-5/5424 */
 #define AR5K_SREV_RAD_5133	0xc0	/* MIMO found on 5418 */
 
 /* IEEE defs */
@@ -269,11 +271,6 @@ enum ath5k_driver_mode {
 /* adding this flag to rate_code enables short preamble, see ar5212_reg.h */
 #define AR5K_SET_SHORT_PREAMBLE 0x04
 
-#define HAS_SHPREAMBLE(_ix) \
-	(rt->rates[_ix].modulation == IEEE80211_RATE_SHORT_PREAMBLE)
-#define SHPREAMBLE_FLAG(_ix) \
-	(HAS_SHPREAMBLE(_ix) ? AR5K_SET_SHORT_PREAMBLE : 0)
-
 
 /****************\
   TX DEFINITIONS
@@ -566,152 +563,61 @@ struct ath5k_athchan_2ghz {
 	u16	a2_athchan;
 };
 
+
 /*
  * Rate definitions
- * TODO: Clean them up or move them on mac80211 -most of these infos are
- * 	 used by the rate control algorytm on MadWiFi.
  */
 
-/* Max number of rates on the rate table and what it seems
- * Atheros hardware supports */
-#define AR5K_MAX_RATES 32
-
 /**
- * struct ath5k_rate - rate structure
- * @valid: is this a valid rate for rate control (remove)
- * @modulation: respective mac80211 modulation
- * @rate_kbps: rate in kbit/s
- * @rate_code: hardware rate value, used in &struct ath5k_desc, on RX on
- *     &struct ath5k_rx_status.rs_rate and on TX on
- *     &struct ath5k_tx_status.ts_rate. Seems the ar5xxx harware supports
- *     up to 32 rates, indexed by 1-32. This means we really only need
- *     6 bits for the rate_code.
- * @dot11_rate: respective IEEE-802.11 rate value
- * @control_rate: index of rate assumed to be used to send control frames.
- *     This can be used to set override the value on the rate duration
- *     registers. This is only useful if we can override in the harware at
- *     what rate we want to send control frames at. Note that IEEE-802.11
- *     Ch. 9.6 (after IEEE 802.11g changes) defines the rate at which we
- *     should send ACK/CTS, if we change this value we can be breaking
- *     the spec.
+ * Seems the ar5xxx harware supports up to 32 rates, indexed by 1-32.
  *
- * This structure is used to get the RX rate or set the TX rate on the
+ * The rate code is used to get the RX rate or set the TX rate on the
  * hardware descriptors. It is also used for internal modulation control
  * and settings.
  *
- * On RX after the &struct ath5k_desc is parsed by the appropriate
- * ah_proc_rx_desc() the respective hardware rate value is set in
- * &struct ath5k_rx_status.rs_rate. On TX the desired rate is set in
- * &struct ath5k_tx_status.ts_rate which is later used to setup the
- * &struct ath5k_desc correctly. This is the hardware rate map we are
- * aware of:
+ * This is the hardware rate map we are aware of:
  *
- * rate_code   1       2       3       4       5       6       7       8
+ * rate_code   0x01    0x02    0x03    0x04    0x05    0x06    0x07    0x08
  * rate_kbps   3000    1000    ?       ?       ?       2000    500     48000
  *
- * rate_code   9       10      11      12      13      14      15      16
+ * rate_code   0x09    0x0A    0x0B    0x0C    0x0D    0x0E    0x0F    0x10
  * rate_kbps   24000   12000   6000    54000   36000   18000   9000    ?
  *
  * rate_code   17      18      19      20      21      22      23      24
  * rate_kbps   ?       ?       ?       ?       ?       ?       ?       11000
  *
  * rate_code   25      26      27      28      29      30      31      32
- * rate_kbps   5500    2000    1000    ?       ?       ?       ?       ?
+ * rate_kbps   5500    2000    1000    11000S  5500S   2000S   ?       ?
  *
+ * "S" indicates CCK rates with short preamble.
+ *
+ * AR5211 has different rate codes for CCK (802.11B) rates. It only uses the
+ * lowest 4 bits, so they are the same as below with a 0xF mask.
+ * (0xB, 0xA, 0x9 and 0x8 for 1M, 2M, 5.5M and 11M).
+ * We handle this in ath5k_setup_bands().
  */
-struct ath5k_rate {
-	u8	valid;
-	u32	modulation;
-	u16	rate_kbps;
-	u8	rate_code;
-	u8	dot11_rate;
-	u8	control_rate;
-};
-
-/* XXX: GRR all this stuff to get leds blinking ??? (check out setcurmode) */
-struct ath5k_rate_table {
-	u16	rate_count;
-	u8	rate_code_to_index[AR5K_MAX_RATES];	/* Back-mapping */
-	struct ath5k_rate rates[AR5K_MAX_RATES];
-};
-
-/*
- * Rate tables...
- * TODO: CLEAN THIS !!!
- */
-#define AR5K_RATES_11A { 8, {					\
-	255, 255, 255, 255, 255, 255, 255, 255, 6, 4, 2, 0,	\
-	7, 5, 3, 1, 255, 255, 255, 255, 255, 255, 255, 255,	\
-	255, 255, 255, 255, 255, 255, 255, 255 }, {		\
-	{ 1, 0, 6000, 11, 140, 0 },		\
-	{ 1, 0, 9000, 15, 18, 0 },		\
-	{ 1, 0, 12000, 10, 152, 2 },		\
-	{ 1, 0, 18000, 14, 36, 2 },		\
-	{ 1, 0, 24000, 9, 176, 4 },		\
-	{ 1, 0, 36000, 13, 72, 4 },		\
-	{ 1, 0, 48000, 8, 96, 4 },		\
-	{ 1, 0, 54000, 12, 108, 4 } }		\
-}
-
-#define AR5K_RATES_11B { 4, {						\
-	255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255,	\
-	255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255, 255,	\
-	3, 2, 1, 0, 255, 255, 255, 255 }, {				\
-	{ 1, 0, 1000, 27, 130, 0 },	\
-	{ 1, IEEE80211_RATE_SHORT_PREAMBLE, 2000, 26, 132, 1 },	\
-	{ 1, IEEE80211_RATE_SHORT_PREAMBLE, 5500, 25, 139, 1 },	\
-	{ 1, IEEE80211_RATE_SHORT_PREAMBLE, 11000, 24, 150, 1 } }	\
-}
-
-#define AR5K_RATES_11G { 12, {					\
-	255, 255, 255, 255, 255, 255, 255, 255, 10, 8, 6, 4,	\
-	11, 9, 7, 5, 255, 255, 255, 255, 255, 255, 255, 255,	\
-	3, 2, 1, 0, 255, 255, 255, 255 }, {			\
-	{ 1, 0, 1000, 27, 2, 0 },		\
-	{ 1, IEEE80211_RATE_SHORT_PREAMBLE, 2000, 26, 4, 1 },		\
-	{ 1, IEEE80211_RATE_SHORT_PREAMBLE, 5500, 25, 11, 1 },		\
-	{ 1, IEEE80211_RATE_SHORT_PREAMBLE, 11000, 24, 22, 1 },	\
-	{ 0, 0, 6000, 11, 12, 4 },	\
-	{ 0, 0, 9000, 15, 18, 4 },	\
-	{ 1, 0, 12000, 10, 24, 6 },	\
-	{ 1, 0, 18000, 14, 36, 6 },	\
-	{ 1, 0, 24000, 9, 48, 8 },	\
-	{ 1, 0, 36000, 13, 72, 8 },	\
-	{ 1, 0, 48000, 8, 96, 8 },	\
-	{ 1, 0, 54000, 12, 108, 8 } }	\
-}
+#define AR5K_MAX_RATES 32
 
-#define AR5K_RATES_TURBO { 8, {					\
-	255, 255, 255, 255, 255, 255, 255, 255, 6, 4, 2, 0,	\
-	7, 5, 3, 1, 255, 255, 255, 255, 255, 255, 255, 255,	\
-	255, 255, 255, 255, 255, 255, 255, 255 }, {		\
-	{ 1, MODULATION_TURBO, 6000, 11, 140, 0 },	\
-	{ 1, MODULATION_TURBO, 9000, 15, 18, 0 },	\
-	{ 1, MODULATION_TURBO, 12000, 10, 152, 2 },	\
-	{ 1, MODULATION_TURBO, 18000, 14, 36, 2 },	\
-	{ 1, MODULATION_TURBO, 24000, 9, 176, 4 },	\
-	{ 1, MODULATION_TURBO, 36000, 13, 72, 4 },	\
-	{ 1, MODULATION_TURBO, 48000, 8, 96, 4 },	\
-	{ 1, MODULATION_TURBO, 54000, 12, 108, 4 } }	\
-}
+/* B */
+#define ATH5K_RATE_CODE_1M	0x1B
+#define ATH5K_RATE_CODE_2M	0x1A
+#define ATH5K_RATE_CODE_5_5M	0x19
+#define ATH5K_RATE_CODE_11M	0x18
+/* A and G */
+#define ATH5K_RATE_CODE_6M	0x0B
+#define ATH5K_RATE_CODE_9M	0x0F
+#define ATH5K_RATE_CODE_12M	0x0A
+#define ATH5K_RATE_CODE_18M	0x0E
+#define ATH5K_RATE_CODE_24M	0x09
+#define ATH5K_RATE_CODE_36M	0x0D
+#define ATH5K_RATE_CODE_48M	0x08
+#define ATH5K_RATE_CODE_54M	0x0C
+/* XR */
+#define ATH5K_RATE_CODE_XR_500K	0x07
+#define ATH5K_RATE_CODE_XR_1M	0x02
+#define ATH5K_RATE_CODE_XR_2M	0x06
+#define ATH5K_RATE_CODE_XR_3M	0x01
 
-#define AR5K_RATES_XR { 12, {					\
-	255, 3, 1, 255, 255, 255, 2, 0, 10, 8, 6, 4,		\
-	11, 9, 7, 5, 255, 255, 255, 255, 255, 255, 255, 255,	\
-	255, 255, 255, 255, 255, 255, 255, 255 }, {		\
-	{ 1, MODULATION_XR, 500, 7, 129, 0 },		\
-	{ 1, MODULATION_XR, 1000, 2, 139, 1 },		\
-	{ 1, MODULATION_XR, 2000, 6, 150, 2 },		\
-	{ 1, MODULATION_XR, 3000, 1, 150, 3 },		\
-	{ 1, 0, 6000, 11, 140, 4 },	\
-	{ 1, 0, 9000, 15, 18, 4 },	\
-	{ 1, 0, 12000, 10, 152, 6 },	\
-	{ 1, 0, 18000, 14, 36, 6 },	\
-	{ 1, 0, 24000, 9, 176, 8 },	\
-	{ 1, 0, 36000, 13, 72, 8 },	\
-	{ 1, 0, 48000, 8, 96, 8 },	\
-	{ 1, 0, 54000, 12, 108, 8 } }	\
-}
 
 /*
  * Crypto definitions
diff --git a/drivers/net/wireless/ath5k/base.c b/drivers/net/wireless/ath5k/base.c
index 217d506..45caa14 100644
--- a/drivers/net/wireless/ath5k/base.c
+++ b/drivers/net/wireless/ath5k/base.c
@@ -40,10 +40,11 @@
  *
  */
 
-#include <linux/version.h>
 #include <linux/module.h>
 #include <linux/delay.h>
+#include <linux/hardirq.h>
 #include <linux/if.h>
+#include <linux/io.h>
 #include <linux/netdevice.h>
 #include <linux/cache.h>
 #include <linux/pci.h>
@@ -93,8 +94,6 @@ static struct pci_device_id ath5k_pci_id_table[] __devinitdata = {
 	{ PCI_VDEVICE(ATHEROS, 0x001a), .driver_data = AR5K_AR5212 }, /* 2413 Griffin-lite */
 	{ PCI_VDEVICE(ATHEROS, 0x001b), .driver_data = AR5K_AR5212 }, /* 5413 Eagle */
 	{ PCI_VDEVICE(ATHEROS, 0x001c), .driver_data = AR5K_AR5212 }, /* 5424 Condor (PCI-E)*/
-	{ PCI_VDEVICE(ATHEROS, 0x0023), .driver_data = AR5K_AR5212 }, /* 5416 */
-	{ PCI_VDEVICE(ATHEROS, 0x0024), .driver_data = AR5K_AR5212 }, /* 5418 */
 	{ 0 }
 };
 MODULE_DEVICE_TABLE(pci, ath5k_pci_id_table);
@@ -133,6 +132,48 @@ static struct ath5k_srev_name srev_names[] = {
 	{ "xxxxx",	AR5K_VERSION_RAD,	AR5K_SREV_UNKNOWN },
 };
 
+static struct ieee80211_rate ath5k_rates[] = {
+	{ .bitrate = 10,
+	  .hw_value = ATH5K_RATE_CODE_1M, },
+	{ .bitrate = 20,
+	  .hw_value = ATH5K_RATE_CODE_2M,
+	  .hw_value_short = ATH5K_RATE_CODE_2M | AR5K_SET_SHORT_PREAMBLE,
+	  .flags = IEEE80211_RATE_SHORT_PREAMBLE },
+	{ .bitrate = 55,
+	  .hw_value = ATH5K_RATE_CODE_5_5M,
+	  .hw_value_short = ATH5K_RATE_CODE_5_5M | AR5K_SET_SHORT_PREAMBLE,
+	  .flags = IEEE80211_RATE_SHORT_PREAMBLE },
+	{ .bitrate = 110,
+	  .hw_value = ATH5K_RATE_CODE_11M,
+	  .hw_value_short = ATH5K_RATE_CODE_11M | AR5K_SET_SHORT_PREAMBLE,
+	  .flags = IEEE80211_RATE_SHORT_PREAMBLE },
+	{ .bitrate = 60,
+	  .hw_value = ATH5K_RATE_CODE_6M,
+	  .flags = 0 },
+	{ .bitrate = 90,
+	  .hw_value = ATH5K_RATE_CODE_9M,
+	  .flags = 0 },
+	{ .bitrate = 120,
+	  .hw_value = ATH5K_RATE_CODE_12M,
+	  .flags = 0 },
+	{ .bitrate = 180,
+	  .hw_value = ATH5K_RATE_CODE_18M,
+	  .flags = 0 },
+	{ .bitrate = 240,
+	  .hw_value = ATH5K_RATE_CODE_24M,
+	  .flags = 0 },
+	{ .bitrate = 360,
+	  .hw_value = ATH5K_RATE_CODE_36M,
+	  .flags = 0 },
+	{ .bitrate = 480,
+	  .hw_value = ATH5K_RATE_CODE_48M,
+	  .flags = 0 },
+	{ .bitrate = 540,
+	  .hw_value = ATH5K_RATE_CODE_54M,
+	  .flags = 0 },
+	/* XR missing */
+};
+
 /*
  * Prototypes - PCI stack related functions
  */
@@ -163,7 +204,8 @@ static struct pci_driver ath5k_pci_driver = {
  * Prototypes - MAC 802.11 stack related functions
  */
 static int ath5k_tx(struct ieee80211_hw *hw, struct sk_buff *skb);
-static int ath5k_reset(struct ieee80211_hw *hw);
+static int ath5k_reset(struct ath5k_softc *sc, bool stop, bool change_channel);
+static int ath5k_reset_wake(struct ath5k_softc *sc);
 static int ath5k_start(struct ieee80211_hw *hw);
 static void ath5k_stop(struct ieee80211_hw *hw);
 static int ath5k_add_interface(struct ieee80211_hw *hw,
@@ -219,20 +261,16 @@ static void 	ath5k_detach(struct pci_dev *pdev,
 			struct ieee80211_hw *hw);
 /* Channel/mode setup */
 static inline short ath5k_ieee2mhz(short chan);
-static unsigned int ath5k_copy_rates(struct ieee80211_rate *rates,
-				const struct ath5k_rate_table *rt,
-				unsigned int max);
 static unsigned int ath5k_copy_channels(struct ath5k_hw *ah,
 				struct ieee80211_channel *channels,
 				unsigned int mode,
 				unsigned int max);
-static int 	ath5k_getchannels(struct ieee80211_hw *hw);
+static int 	ath5k_setup_bands(struct ieee80211_hw *hw);
 static int 	ath5k_chan_set(struct ath5k_softc *sc,
 				struct ieee80211_channel *chan);
 static void	ath5k_setcurmode(struct ath5k_softc *sc,
 				unsigned int mode);
 static void	ath5k_mode_setup(struct ath5k_softc *sc);
-static void	ath5k_set_total_hw_rates(struct ath5k_softc *sc);
 
 /* Descriptor setup */
 static int	ath5k_desc_alloc(struct ath5k_softc *sc,
@@ -252,7 +290,7 @@ static inline void ath5k_txbuf_free(struct ath5k_softc *sc,
 		return;
 	pci_unmap_single(sc->pdev, bf->skbaddr, bf->skb->len,
 			PCI_DMA_TODEVICE);
-	dev_kfree_skb(bf->skb);
+	dev_kfree_skb_any(bf->skb);
 	bf->skb = NULL;
 }
 
@@ -467,13 +505,11 @@ ath5k_pci_probe(struct pci_dev *pdev,
 	mutex_init(&sc->lock);
 	spin_lock_init(&sc->rxbuflock);
 	spin_lock_init(&sc->txbuflock);
+	spin_lock_init(&sc->block);
 
 	/* Set private data */
 	pci_set_drvdata(pdev, hw);
 
-	/* Enable msi for devices that support it */
-	pci_enable_msi(pdev);
-
 	/* Setup interrupt handler */
 	ret = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc);
 	if (ret) {
@@ -551,7 +587,6 @@ err_ah:
 err_irq:
 	free_irq(pdev->irq, sc);
 err_free:
-	pci_disable_msi(pdev);
 	ieee80211_free_hw(hw);
 err_map:
 	pci_iounmap(pdev, mem);
@@ -573,7 +608,6 @@ ath5k_pci_remove(struct pci_dev *pdev)
 	ath5k_detach(pdev, hw);
 	ath5k_hw_detach(sc->ah);
 	free_irq(pdev->irq, sc);
-	pci_disable_msi(pdev);
 	pci_iounmap(pdev, sc->iobase);
 	pci_release_region(pdev, 0);
 	pci_disable_device(pdev);
@@ -590,6 +624,8 @@ ath5k_pci_suspend(struct pci_dev *pdev, pm_message_t state)
 	ath5k_led_off(sc);
 
 	ath5k_stop_hw(sc);
+
+	free_irq(pdev->irq, sc);
 	pci_save_state(pdev);
 	pci_disable_device(pdev);
 	pci_set_power_state(pdev, PCI_D3hot);
@@ -605,15 +641,12 @@ ath5k_pci_resume(struct pci_dev *pdev)
 	struct ath5k_hw *ah = sc->ah;
 	int i, err;
 
-	err = pci_set_power_state(pdev, PCI_D0);
-	if (err)
-		return err;
+	pci_restore_state(pdev);
 
 	err = pci_enable_device(pdev);
 	if (err)
 		return err;
 
-	pci_restore_state(pdev);
 	/*
 	 * Suspend/Resume resets the PCI configuration space, so we have to
 	 * re-disable the RETRY_TIMEOUT register (0x41) to keep
@@ -621,7 +654,15 @@ ath5k_pci_resume(struct pci_dev *pdev)
 	 */
 	pci_write_config_byte(pdev, 0x41, 0);
 
-	ath5k_init(sc);
+	err = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc);
+	if (err) {
+		ATH5K_ERR(sc, "request_irq failed\n");
+		goto err_no_irq;
+	}
+
+	err = ath5k_init(sc);
+	if (err)
+		goto err_irq;
 	ath5k_led_enable(sc);
 
 	/*
@@ -635,11 +676,15 @@ ath5k_pci_resume(struct pci_dev *pdev)
 		ath5k_hw_reset_key(ah, i);
 
 	return 0;
+err_irq:
+	free_irq(pdev->irq, sc);
+err_no_irq:
+	pci_disable_device(pdev);
+	return err;
 }
 #endif /* CONFIG_PM */
 
 
-
 /***********************\
 * Driver Initialization *
 \***********************/
@@ -681,15 +726,12 @@ ath5k_attach(struct pci_dev *pdev, struct ieee80211_hw *hw)
 	 * on settings like the phy mode and regulatory
 	 * domain restrictions.
 	 */
-	ret = ath5k_getchannels(hw);
+	ret = ath5k_setup_bands(hw);
 	if (ret) {
 		ATH5K_ERR(sc, "can't get channels\n");
 		goto err;
 	}
 
-	/* Set *_rates so we can map hw rate index */
-	ath5k_set_total_hw_rates(sc);
-
 	/* NB: setup here so ath5k_rate_update is happy */
 	if (test_bit(AR5K_MODE_11A, ah->ah_modes))
 		ath5k_setcurmode(sc, AR5K_MODE_11A);
@@ -806,27 +848,6 @@ ath5k_ieee2mhz(short chan)
 }
 
 static unsigned int
-ath5k_copy_rates(struct ieee80211_rate *rates,
-		const struct ath5k_rate_table *rt,
-		unsigned int max)
-{
-	unsigned int i, count;
-
-	if (rt == NULL)
-		return 0;
-
-	for (i = 0, count = 0; i < rt->rate_count && max > 0; i++) {
-		rates[count].bitrate = rt->rates[i].rate_kbps / 100;
-		rates[count].hw_value = rt->rates[i].rate_code;
-		rates[count].flags = rt->rates[i].modulation;
-		count++;
-		max--;
-	}
-
-	return count;
-}
-
-static unsigned int
 ath5k_copy_channels(struct ath5k_hw *ah,
 		struct ieee80211_channel *channels,
 		unsigned int mode,
@@ -888,74 +909,97 @@ ath5k_copy_channels(struct ath5k_hw *ah,
 	return count;
 }
 
+static void
+ath5k_setup_rate_idx(struct ath5k_softc *sc, struct ieee80211_supported_band *b)
+{
+	u8 i;
+
+	for (i = 0; i < AR5K_MAX_RATES; i++)
+		sc->rate_idx[b->band][i] = -1;
+
+	for (i = 0; i < b->n_bitrates; i++) {
+		sc->rate_idx[b->band][b->bitrates[i].hw_value] = i;
+		if (b->bitrates[i].hw_value_short)
+			sc->rate_idx[b->band][b->bitrates[i].hw_value_short] = i;
+	}
+}
+
 static int
-ath5k_getchannels(struct ieee80211_hw *hw)
+ath5k_setup_bands(struct ieee80211_hw *hw)
 {
 	struct ath5k_softc *sc = hw->priv;
 	struct ath5k_hw *ah = sc->ah;
-	struct ieee80211_supported_band *sbands = sc->sbands;
-	const struct ath5k_rate_table *hw_rates;
-	unsigned int max_r, max_c, count_r, count_c;
-	int mode2g = AR5K_MODE_11G;
+	struct ieee80211_supported_band *sband;
+	int max_c, count_c = 0;
+	int i;
 
 	BUILD_BUG_ON(ARRAY_SIZE(sc->sbands) < IEEE80211_NUM_BANDS);
-
-	max_r = ARRAY_SIZE(sc->rates);
 	max_c = ARRAY_SIZE(sc->channels);
-	count_r = count_c = 0;
 
 	/* 2GHz band */
-	if (!test_bit(AR5K_MODE_11G, sc->ah->ah_capabilities.cap_mode)) {
-		mode2g = AR5K_MODE_11B;
-		if (!test_bit(AR5K_MODE_11B,
-			sc->ah->ah_capabilities.cap_mode))
-			mode2g = -1;
-	}
+	sband = &sc->sbands[IEEE80211_BAND_2GHZ];
+	sband->band = IEEE80211_BAND_2GHZ;
+	sband->bitrates = &sc->rates[IEEE80211_BAND_2GHZ][0];
 
-	if (mode2g > 0) {
-		struct ieee80211_supported_band *sband =
-			&sbands[IEEE80211_BAND_2GHZ];
+	if (test_bit(AR5K_MODE_11G, sc->ah->ah_capabilities.cap_mode)) {
+		/* G mode */
+		memcpy(sband->bitrates, &ath5k_rates[0],
+		       sizeof(struct ieee80211_rate) * 12);
+		sband->n_bitrates = 12;
 
-		sband->bitrates = sc->rates;
 		sband->channels = sc->channels;
-
-		sband->band = IEEE80211_BAND_2GHZ;
 		sband->n_channels = ath5k_copy_channels(ah, sband->channels,
-					mode2g, max_c);
-
-		hw_rates = ath5k_hw_get_rate_table(ah, mode2g);
-		sband->n_bitrates = ath5k_copy_rates(sband->bitrates,
-					hw_rates, max_r);
+					AR5K_MODE_11G, max_c);
 
+		hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband;
 		count_c = sband->n_channels;
-		count_r = sband->n_bitrates;
+		max_c -= count_c;
+	} else if (test_bit(AR5K_MODE_11B, sc->ah->ah_capabilities.cap_mode)) {
+		/* B mode */
+		memcpy(sband->bitrates, &ath5k_rates[0],
+		       sizeof(struct ieee80211_rate) * 4);
+		sband->n_bitrates = 4;
+
+		/* 5211 only supports B rates and uses 4bit rate codes
+		 * (e.g normally we have 0x1B for 1M, but on 5211 we have 0x0B)
+		 * fix them up here:
+		 */
+		if (ah->ah_version == AR5K_AR5211) {
+			for (i = 0; i < 4; i++) {
+				sband->bitrates[i].hw_value =
+					sband->bitrates[i].hw_value & 0xF;
+				sband->bitrates[i].hw_value_short =
+					sband->bitrates[i].hw_value_short & 0xF;
+			}
+		}
 
-		hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband;
+		sband->channels = sc->channels;
+		sband->n_channels = ath5k_copy_channels(ah, sband->channels,
+					AR5K_MODE_11B, max_c);
 
-		max_r -= count_r;
+		hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband;
+		count_c = sband->n_channels;
 		max_c -= count_c;
-
 	}
+	ath5k_setup_rate_idx(sc, sband);
 
-	/* 5GHz band */
-
+	/* 5GHz band, A mode */
 	if (test_bit(AR5K_MODE_11A, sc->ah->ah_capabilities.cap_mode)) {
-		struct ieee80211_supported_band *sband =
-			&sbands[IEEE80211_BAND_5GHZ];
+		sband = &sc->sbands[IEEE80211_BAND_5GHZ];
+		sband->band = IEEE80211_BAND_5GHZ;
+		sband->bitrates = &sc->rates[IEEE80211_BAND_5GHZ][0];
 
-		sband->bitrates = &sc->rates[count_r];
-		sband->channels = &sc->channels[count_c];
+		memcpy(sband->bitrates, &ath5k_rates[4],
+		       sizeof(struct ieee80211_rate) * 8);
+		sband->n_bitrates = 8;
 
-		sband->band = IEEE80211_BAND_5GHZ;
+		sband->channels = &sc->channels[count_c];
 		sband->n_channels = ath5k_copy_channels(ah, sband->channels,
 					AR5K_MODE_11A, max_c);
 
-		hw_rates = ath5k_hw_get_rate_table(ah, AR5K_MODE_11A);
-		sband->n_bitrates = ath5k_copy_rates(sband->bitrates,
-					hw_rates, max_r);
-
 		hw->wiphy->bands[IEEE80211_BAND_5GHZ] = sband;
 	}
+	ath5k_setup_rate_idx(sc, sband);
 
 	ath5k_debug_dump_bands(sc);
 
@@ -971,9 +1015,6 @@ ath5k_getchannels(struct ieee80211_hw *hw)
 static int
 ath5k_chan_set(struct ath5k_softc *sc, struct ieee80211_channel *chan)
 {
-	struct ath5k_hw *ah = sc->ah;
-	int ret;
-
 	ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "(%u MHz) -> (%u MHz)\n",
 		sc->curchan->center_freq, chan->center_freq);
 
@@ -989,41 +1030,7 @@ ath5k_chan_set(struct ath5k_softc *sc, struct ieee80211_channel *chan)
 		 * hardware at the new frequency, and then re-enable
 		 * the relevant bits of the h/w.
 		 */
-		ath5k_hw_set_intr(ah, 0);	/* disable interrupts */
-		ath5k_txq_cleanup(sc);		/* clear pending tx frames */
-		ath5k_rx_stop(sc);		/* turn off frame recv */
-		ret = ath5k_hw_reset(ah, sc->opmode, sc->curchan, true);
-		if (ret) {
-			ATH5K_ERR(sc, "%s: unable to reset channel "
-				"(%u Mhz)\n", __func__, chan->center_freq);
-			return ret;
-		}
-
-		ath5k_hw_set_txpower_limit(sc->ah, 0);
-
-		/*
-		 * Re-enable rx framework.
-		 */
-		ret = ath5k_rx_start(sc);
-		if (ret) {
-			ATH5K_ERR(sc, "%s: unable to restart recv logic\n",
-					__func__);
-			return ret;
-		}
-
-		/*
-		 * Change channels and update the h/w rate map
-		 * if we're switching; e.g. 11a to 11b/g.
-		 *
-		 * XXX needed?
-		 */
-/*		ath5k_chan_change(sc, chan); */
-
-		ath5k_beacon_config(sc);
-		/*
-		 * Re-enable interrupts.
-		 */
-		ath5k_hw_set_intr(ah, sc->imask);
+		return ath5k_reset(sc, true, true);
 	}
 
 	return 0;
@@ -1061,75 +1068,13 @@ ath5k_mode_setup(struct ath5k_softc *sc)
 	ATH5K_DBG(sc, ATH5K_DEBUG_MODE, "RX filter 0x%x\n", rfilt);
 }
 
-/*
- * Match the hw provided rate index (through descriptors)
- * to an index for sc->curband->bitrates, so it can be used
- * by the stack.
- *
- * This one is a little bit tricky but i think i'm right
- * about this...
- *
- * We have 4 rate tables in the following order:
- * XR (4 rates)
- * 802.11a (8 rates)
- * 802.11b (4 rates)
- * 802.11g (12 rates)
- * that make the hw rate table.
- *
- * Lets take a 5211 for example that supports a and b modes only.
- * First comes the 802.11a table and then 802.11b (total 12 rates).
- * When hw returns eg. 11 it points to the last 802.11b rate (11Mbit),
- * if it returns 2 it points to the second 802.11a rate etc.
- *
- * Same goes for 5212 who has xr/a/b/g support (total 28 rates).
- * First comes the XR table, then 802.11a, 802.11b and 802.11g.
- * When hw returns eg. 27 it points to the last 802.11g rate (54Mbits) etc
- */
-static void
-ath5k_set_total_hw_rates(struct ath5k_softc *sc) {
-
-	struct ath5k_hw *ah = sc->ah;
-
-	if (test_bit(AR5K_MODE_11A, ah->ah_modes))
-		sc->a_rates = 8;
-
-	if (test_bit(AR5K_MODE_11B, ah->ah_modes))
-		sc->b_rates = 4;
-
-	if (test_bit(AR5K_MODE_11G, ah->ah_modes))
-		sc->g_rates = 12;
-
-	/* XXX: Need to see what what happens when
-		xr disable bits in eeprom are set */
-	if (ah->ah_version >= AR5K_AR5212)
-		sc->xr_rates = 4;
-
-}
-
 static inline int
-ath5k_hw_to_driver_rix(struct ath5k_softc *sc, int hw_rix) {
-
-	int mac80211_rix;
-
-	if(sc->curband->band == IEEE80211_BAND_2GHZ) {
-		/* We setup a g ratetable for both b/g modes */
-		mac80211_rix =
-			hw_rix - sc->b_rates - sc->a_rates - sc->xr_rates;
-	} else {
-		mac80211_rix = hw_rix - sc->xr_rates;
-	}
-
-	/* Something went wrong, fallback to basic rate for this band */
-	if ((mac80211_rix >= sc->curband->n_bitrates) ||
-		(mac80211_rix <= 0 ))
-		mac80211_rix = 1;
-
-	return mac80211_rix;
+ath5k_hw_to_driver_rix(struct ath5k_softc *sc, int hw_rix)
+{
+	WARN_ON(hw_rix < 0 || hw_rix > AR5K_MAX_RATES);
+	return sc->rate_idx[sc->curband->band][hw_rix];
 }
 
-
-
-
 /***************\
 * Buffers setup *
 \***************/
@@ -1224,7 +1169,7 @@ ath5k_txbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf)
 
 	pktlen = skb->len;
 
-	if (!(info->flags & IEEE80211_TX_CTL_DO_NOT_ENCRYPT)) {
+	if (info->control.hw_key) {
 		keyidx = info->control.hw_key->hw_key_idx;
 		pktlen += info->control.icv_len;
 	}
@@ -1249,6 +1194,7 @@ ath5k_txbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf)
 
 	txq->link = &ds->ds_link;
 	ath5k_hw_tx_start(ah, txq->qnum);
+	mmiowb();
 	spin_unlock_bh(&txq->lock);
 
 	return 0;
@@ -1425,7 +1371,8 @@ ath5k_beaconq_config(struct ath5k_softc *sc)
 	ret = ath5k_hw_get_tx_queueprops(ah, sc->bhalq, &qi);
 	if (ret)
 		return ret;
-	if (sc->opmode == IEEE80211_IF_TYPE_AP) {
+	if (sc->opmode == IEEE80211_IF_TYPE_AP ||
+		sc->opmode == IEEE80211_IF_TYPE_MESH_POINT) {
 		/*
 		 * Always burst out beacon and CAB traffic
 		 * (aifs = cwmin = cwmax = 0)
@@ -1583,7 +1530,6 @@ ath5k_rx_stop(struct ath5k_softc *sc)
 	ath5k_hw_stop_pcu_recv(ah);	/* disable PCU */
 	ath5k_hw_set_rx_filter(ah, 0);	/* clear recv filter */
 	ath5k_hw_stop_rx_dma(ah);	/* disable DMA engine */
-	mdelay(3);			/* 3ms is long enough for 1 frame */
 
 	ath5k_debug_printrxbuffs(sc, ah);
 
@@ -1595,7 +1541,7 @@ ath5k_rx_decrypted(struct ath5k_softc *sc, struct ath5k_desc *ds,
 		struct sk_buff *skb, struct ath5k_rx_status *rs)
 {
 	struct ieee80211_hdr *hdr = (void *)skb->data;
-	unsigned int keyix, hlen = ieee80211_get_hdrlen_from_skb(skb);
+	unsigned int keyix, hlen;
 
 	if (!(rs->rs_status & AR5K_RXERR_DECRYPT) &&
 			rs->rs_keyix != AR5K_RXKEYIX_INVALID)
@@ -1604,6 +1550,7 @@ ath5k_rx_decrypted(struct ath5k_softc *sc, struct ath5k_desc *ds,
 	/* Apparently when a default key is used to decrypt the packet
 	   the hw does not set the index used to decrypt.  In such cases
 	   get the index from the packet. */
+	hlen = ieee80211_hdrlen(hdr->frame_control);
 	if (ieee80211_has_protected(hdr->frame_control) &&
 	    !(rs->rs_status & AR5K_RXERR_DECRYPT) &&
 	    skb->len >= hlen + 4) {
@@ -1682,31 +1629,44 @@ ath5k_tasklet_rx(unsigned long data)
 	struct ath5k_rx_status rs = {};
 	struct sk_buff *skb;
 	struct ath5k_softc *sc = (void *)data;
-	struct ath5k_buf *bf;
+	struct ath5k_buf *bf, *bf_last;
 	struct ath5k_desc *ds;
 	int ret;
 	int hdrlen;
 	int pad;
 
 	spin_lock(&sc->rxbuflock);
+	if (list_empty(&sc->rxbuf)) {
+		ATH5K_WARN(sc, "empty rx buf pool\n");
+		goto unlock;
+	}
+	bf_last = list_entry(sc->rxbuf.prev, struct ath5k_buf, list);
 	do {
 		rxs.flag = 0;
 
-		if (unlikely(list_empty(&sc->rxbuf))) {
-			ATH5K_WARN(sc, "empty rx buf pool\n");
-			break;
-		}
 		bf = list_first_entry(&sc->rxbuf, struct ath5k_buf, list);
 		BUG_ON(bf->skb == NULL);
 		skb = bf->skb;
 		ds = bf->desc;
 
-		/* TODO only one segment */
-		pci_dma_sync_single_for_cpu(sc->pdev, sc->desc_daddr,
-				sc->desc_len, PCI_DMA_FROMDEVICE);
-
-		if (unlikely(ds->ds_link == bf->daddr)) /* this is the end */
-			break;
+		/*
+		 * last buffer must not be freed to ensure proper hardware
+		 * function. When the hardware finishes also a packet next to
+		 * it, we are sure, it doesn't use it anymore and we can go on.
+		 */
+		if (bf_last == bf)
+			bf->flags |= 1;
+		if (bf->flags) {
+			struct ath5k_buf *bf_next = list_entry(bf->list.next,
+					struct ath5k_buf, list);
+			ret = sc->ah->ah_proc_rx_desc(sc->ah, bf_next->desc,
+					&rs);
+			if (ret)
+				break;
+			bf->flags &= ~1;
+			/* skip the overwritten one (even status is martian) */
+			goto next;
+		}
 
 		ret = sc->ah->ah_proc_rx_desc(sc->ah, ds, &rs);
 		if (unlikely(ret == -EINPROGRESS))
@@ -1752,8 +1712,6 @@ ath5k_tasklet_rx(unsigned long data)
 				goto next;
 		}
 accept:
-		pci_dma_sync_single_for_cpu(sc->pdev, bf->skbaddr,
-				rs.rs_datalen, PCI_DMA_FROMDEVICE);
 		pci_unmap_single(sc->pdev, bf->skbaddr, sc->rxbufsize,
 				PCI_DMA_FROMDEVICE);
 		bf->skb = NULL;
@@ -1806,6 +1764,10 @@ accept:
 		rxs.rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate);
 		rxs.flag |= ath5k_rx_decrypted(sc, ds, skb, &rs);
 
+		if (rxs.rate_idx >= 0 && rs.rs_rate ==
+		    sc->curband->bitrates[rxs.rate_idx].hw_value_short)
+			rxs.flag |= RX_FLAG_SHORTPRE;
+
 		ath5k_debug_dump_skb(sc, skb, "RX  ", 0);
 
 		/* check beacons in IBSS mode */
@@ -1816,6 +1778,7 @@ accept:
 next:
 		list_move_tail(&bf->list, &sc->rxbuf);
 	} while (ath5k_rxbuf_setup(sc, bf) == 0);
+unlock:
 	spin_unlock(&sc->rxbuflock);
 }
 
@@ -1840,9 +1803,6 @@ ath5k_tx_processq(struct ath5k_softc *sc, struct ath5k_txq *txq)
 	list_for_each_entry_safe(bf, bf0, &txq->q, list) {
 		ds = bf->desc;
 
-		/* TODO only one segment */
-		pci_dma_sync_single_for_cpu(sc->pdev, sc->desc_daddr,
-				sc->desc_len, PCI_DMA_FROMDEVICE);
 		ret = sc->ah->ah_proc_tx_desc(sc->ah, ds, &ts);
 		if (unlikely(ret == -EINPROGRESS))
 			break;
@@ -2015,8 +1975,6 @@ ath5k_beacon_send(struct ath5k_softc *sc)
 		ATH5K_WARN(sc, "beacon queue %u didn't stop?\n", sc->bhalq);
 		/* NB: hw still stops DMA, so proceed */
 	}
-	pci_dma_sync_single_for_cpu(sc->pdev, bf->skbaddr, bf->skb->len,
-			PCI_DMA_TODEVICE);
 
 	ath5k_hw_put_tx_buf(ah, sc->bhalq, bf->daddr);
 	ath5k_hw_tx_start(ah, sc->bhalq);
@@ -2150,6 +2108,7 @@ ath5k_beacon_config(struct ath5k_softc *sc)
 
 	ath5k_hw_set_intr(ah, 0);
 	sc->bmisscount = 0;
+	sc->imask &= ~(AR5K_INT_BMISS | AR5K_INT_SWBA);
 
 	if (sc->opmode == IEEE80211_IF_TYPE_STA) {
 		sc->imask |= AR5K_INT_BMISS;
@@ -2165,8 +2124,11 @@ ath5k_beacon_config(struct ath5k_softc *sc)
 
 		sc->imask |= AR5K_INT_SWBA;
 
-		if (ath5k_hw_hasveol(ah))
+		if (ath5k_hw_hasveol(ah)) {
+			spin_lock(&sc->block);
 			ath5k_beacon_send(sc);
+			spin_unlock(&sc->block);
+		}
 	}
 	/* TODO else AP */
 
@@ -2202,36 +2164,13 @@ ath5k_init(struct ath5k_softc *sc)
 	 */
 	sc->curchan = sc->hw->conf.channel;
 	sc->curband = &sc->sbands[sc->curchan->band];
-	ret = ath5k_hw_reset(sc->ah, sc->opmode, sc->curchan, false);
-	if (ret) {
-		ATH5K_ERR(sc, "unable to reset hardware: %d\n", ret);
-		goto done;
-	}
-	/*
-	 * This is needed only to setup initial state
-	 * but it's best done after a reset.
-	 */
-	ath5k_hw_set_txpower_limit(sc->ah, 0);
-
-	/*
-	 * Setup the hardware after reset: the key cache
-	 * is filled as needed and the receive engine is
-	 * set going.  Frame transmit is handled entirely
-	 * in the frame output path; there's nothing to do
-	 * here except setup the interrupt mask.
-	 */
-	ret = ath5k_rx_start(sc);
-	if (ret)
-		goto done;
-
-	/*
-	 * Enable interrupts.
-	 */
 	sc->imask = AR5K_INT_RX | AR5K_INT_TX | AR5K_INT_RXEOL |
 		AR5K_INT_RXORN | AR5K_INT_FATAL | AR5K_INT_GLOBAL |
 		AR5K_INT_MIB;
+	ret = ath5k_reset(sc, false, false);
+	if (ret)
+		goto done;
 
-	ath5k_hw_set_intr(sc->ah, sc->imask);
 	/* Set ack to be sent at low bit-rates */
 	ath5k_hw_set_ack_bitrate_high(sc->ah, false);
 
@@ -2240,6 +2179,7 @@ ath5k_init(struct ath5k_softc *sc)
 
 	ret = 0;
 done:
+	mmiowb();
 	mutex_unlock(&sc->lock);
 	return ret;
 }
@@ -2272,6 +2212,7 @@ ath5k_stop_locked(struct ath5k_softc *sc)
 	if (!test_bit(ATH_STAT_INVALID, sc->status)) {
 		ath5k_led_off(sc);
 		ath5k_hw_set_intr(ah, 0);
+		synchronize_irq(sc->pdev->irq);
 	}
 	ath5k_txq_cleanup(sc);
 	if (!test_bit(ATH_STAT_INVALID, sc->status)) {
@@ -2321,9 +2262,13 @@ ath5k_stop_hw(struct ath5k_softc *sc)
 		}
 	}
 	ath5k_txbuf_free(sc, sc->bbuf);
+	mmiowb();
 	mutex_unlock(&sc->lock);
 
 	del_timer_sync(&sc->calib_tim);
+	tasklet_kill(&sc->rxtq);
+	tasklet_kill(&sc->txtq);
+	tasklet_kill(&sc->restq);
 
 	return ret;
 }
@@ -2383,7 +2328,9 @@ ath5k_intr(int irq, void *dev_id)
 						  TSF_TO_TU(tsf),
 						  (unsigned long long) tsf);
 				} else {
+					spin_lock(&sc->block);
 					ath5k_beacon_send(sc);
+					spin_unlock(&sc->block);
 				}
 			}
 			if (status & AR5K_INT_RXEOL) {
@@ -2425,7 +2372,7 @@ ath5k_tasklet_reset(unsigned long data)
 {
 	struct ath5k_softc *sc = (void *)data;
 
-	ath5k_reset(sc->hw);
+	ath5k_reset_wake(sc);
 }
 
 /*
@@ -2448,7 +2395,7 @@ ath5k_calibrate(unsigned long data)
 		 * to load new gain values.
 		 */
 		ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "calibration, resetting\n");
-		ath5k_reset(sc->hw);
+		ath5k_reset_wake(sc);
 	}
 	if (ath5k_hw_phy_calibrate(ah, sc->curchan))
 		ATH5K_ERR(sc, "calibration of channel %u failed\n",
@@ -2550,8 +2497,6 @@ ath5k_init_leds(struct ath5k_softc *sc)
 	struct pci_dev *pdev = sc->pdev;
 	char name[ATH5K_LED_MAX_NAME_LEN + 1];
 
-	sc->led_on = 0;  /* active low */
-
 	/*
 	 * Auto-enable soft led processing for IBM cards and for
 	 * 5211 minipci cards.
@@ -2560,11 +2505,13 @@ ath5k_init_leds(struct ath5k_softc *sc)
 	    pdev->device == PCI_DEVICE_ID_ATHEROS_AR5211) {
 		__set_bit(ATH_STAT_LEDSOFT, sc->status);
 		sc->led_pin = 0;
+		sc->led_on = 0;  /* active low */
 	}
 	/* Enable softled on PIN1 on HP Compaq nc6xx, nc4000 & nx5000 laptops */
 	if (pdev->subsystem_vendor == PCI_VENDOR_ID_COMPAQ) {
 		__set_bit(ATH_STAT_LEDSOFT, sc->status);
 		sc->led_pin = 1;
+		sc->led_on = 1;  /* active high */
 	}
 	if (!test_bit(ATH_STAT_LEDSOFT, sc->status))
 		goto out;
@@ -2649,48 +2596,67 @@ ath5k_tx(struct ieee80211_hw *hw, struct sk_buff *skb)
 }
 
 static int
-ath5k_reset(struct ieee80211_hw *hw)
+ath5k_reset(struct ath5k_softc *sc, bool stop, bool change_channel)
 {
-	struct ath5k_softc *sc = hw->priv;
 	struct ath5k_hw *ah = sc->ah;
 	int ret;
 
 	ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "resetting\n");
 
-	ath5k_hw_set_intr(ah, 0);
-	ath5k_txq_cleanup(sc);
-	ath5k_rx_stop(sc);
-
+	if (stop) {
+		ath5k_hw_set_intr(ah, 0);
+		ath5k_txq_cleanup(sc);
+		ath5k_rx_stop(sc);
+	}
 	ret = ath5k_hw_reset(ah, sc->opmode, sc->curchan, true);
-	if (unlikely(ret)) {
+	if (ret) {
 		ATH5K_ERR(sc, "can't reset hardware (%d)\n", ret);
 		goto err;
 	}
+
+	/*
+	 * This is needed only to setup initial state
+	 * but it's best done after a reset.
+	 */
 	ath5k_hw_set_txpower_limit(sc->ah, 0);
 
 	ret = ath5k_rx_start(sc);
-	if (unlikely(ret)) {
+	if (ret) {
 		ATH5K_ERR(sc, "can't start recv logic\n");
 		goto err;
 	}
+
 	/*
-	 * We may be doing a reset in response to an ioctl
-	 * that changes the channel so update any state that
-	 * might change as a result.
+	 * Change channels and update the h/w rate map if we're switching;
+	 * e.g. 11a to 11b/g.
+	 *
+	 * We may be doing a reset in response to an ioctl that changes the
+	 * channel so update any state that might change as a result.
 	 *
 	 * XXX needed?
 	 */
 /*	ath5k_chan_change(sc, c); */
-	ath5k_beacon_config(sc);
-	/* intrs are started by ath5k_beacon_config */
 
-	ieee80211_wake_queues(hw);
+	ath5k_beacon_config(sc);
+	/* intrs are enabled by ath5k_beacon_config */
 
 	return 0;
 err:
 	return ret;
 }
 
+static int
+ath5k_reset_wake(struct ath5k_softc *sc)
+{
+	int ret;
+
+	ret = ath5k_reset(sc, true, true);
+	if (!ret)
+		ieee80211_wake_queues(sc->hw);
+
+	return ret;
+}
+
 static int ath5k_start(struct ieee80211_hw *hw)
 {
 	return ath5k_init(hw->priv);
@@ -2725,6 +2691,11 @@ static int ath5k_add_interface(struct ieee80211_hw *hw,
 		ret = -EOPNOTSUPP;
 		goto end;
 	}
+
+	/* Set to a reasonable value. Note that this will
+	 * be set to mac80211's value at ath5k_config(). */
+	sc->bintval = 1000;
+
 	ret = 0;
 end:
 	mutex_unlock(&sc->lock);
@@ -2769,9 +2740,6 @@ ath5k_config_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 	struct ath5k_hw *ah = sc->ah;
 	int ret;
 
-	/* Set to a reasonable value. Note that this will
-	 * be set to mac80211's value at ath5k_config(). */
-	sc->bintval = 1000;
 	mutex_lock(&sc->lock);
 	if (sc->vif != vif) {
 		ret = -EIO;
@@ -2783,6 +2751,7 @@ ath5k_config_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 		/* XXX: assoc id is set to 0 for now, mac80211 doesn't have
 		 * a clean way of letting us retrieve this yet. */
 		ath5k_hw_set_associd(ah, ah->ah_bssid, 0);
+		mmiowb();
 	}
 
 	if (conf->changed & IEEE80211_IFCC_BEACON &&
@@ -2798,7 +2767,7 @@ ath5k_config_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif,
 
 	mutex_unlock(&sc->lock);
 
-	return ath5k_reset(hw);
+	return ath5k_reset_wake(sc);
 unlock:
 	mutex_unlock(&sc->lock);
 	return ret;
@@ -2911,6 +2880,7 @@ static void ath5k_configure_filter(struct ieee80211_hw *hw,
 	if (sc->opmode != IEEE80211_IF_TYPE_STA)
 		rfilt |= AR5K_RX_FILTER_PROBEREQ;
 	if (sc->opmode != IEEE80211_IF_TYPE_AP &&
+		sc->opmode != IEEE80211_IF_TYPE_MESH_POINT &&
 		test_bit(ATH_STAT_PROMISC, sc->status))
 		rfilt |= AR5K_RX_FILTER_PROM;
 	if (sc->opmode == IEEE80211_IF_TYPE_STA ||
@@ -2971,6 +2941,7 @@ ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	}
 
 unlock:
+	mmiowb();
 	mutex_unlock(&sc->lock);
 	return ret;
 }
@@ -3028,27 +2999,29 @@ static int
 ath5k_beacon_update(struct ieee80211_hw *hw, struct sk_buff *skb)
 {
 	struct ath5k_softc *sc = hw->priv;
+	unsigned long flags;
 	int ret;
 
 	ath5k_debug_dump_skb(sc, skb, "BC  ", 1);
 
-	mutex_lock(&sc->lock);
-
 	if (sc->opmode != IEEE80211_IF_TYPE_IBSS) {
 		ret = -EIO;
 		goto end;
 	}
 
+	spin_lock_irqsave(&sc->block, flags);
 	ath5k_txbuf_free(sc, sc->bbuf);
 	sc->bbuf->skb = skb;
 	ret = ath5k_beacon_setup(sc, sc->bbuf);
 	if (ret)
 		sc->bbuf->skb = NULL;
-	else
+	spin_unlock_irqrestore(&sc->block, flags);
+	if (!ret) {
 		ath5k_beacon_config(sc);
+		mmiowb();
+	}
 
 end:
-	mutex_unlock(&sc->lock);
 	return ret;
 }
 
diff --git a/drivers/net/wireless/ath5k/base.h b/drivers/net/wireless/ath5k/base.h
index 47f414b..1549b63 100644
--- a/drivers/net/wireless/ath5k/base.h
+++ b/drivers/net/wireless/ath5k/base.h
@@ -56,7 +56,7 @@
 
 struct ath5k_buf {
 	struct list_head	list;
-	unsigned int		flags;	/* tx descriptor flags */
+	unsigned int		flags;	/* rx descriptor flags */
 	struct ath5k_desc	*desc;	/* virtual addr of desc */
 	dma_addr_t		daddr;	/* physical addr of desc */
 	struct sk_buff		*skb;	/* skbuff for buf */
@@ -111,17 +111,13 @@ struct ath5k_softc {
 	struct ieee80211_hw	*hw;		/* IEEE 802.11 common */
 	struct ieee80211_supported_band sbands[IEEE80211_NUM_BANDS];
 	struct ieee80211_channel channels[ATH_CHAN_MAX];
-	struct ieee80211_rate	rates[AR5K_MAX_RATES * IEEE80211_NUM_BANDS];
+	struct ieee80211_rate	rates[IEEE80211_NUM_BANDS][AR5K_MAX_RATES];
+	u8			rate_idx[IEEE80211_NUM_BANDS][AR5K_MAX_RATES];
 	enum ieee80211_if_types	opmode;
 	struct ath5k_hw		*ah;		/* Atheros HW */
 
 	struct ieee80211_supported_band		*curband;
 
-	u8			a_rates;
-	u8			b_rates;
-	u8			g_rates;
-	u8			xr_rates;
-
 #ifdef CONFIG_ATH5K_DEBUG
 	struct ath5k_dbg_info	debug;		/* debug info */
 #endif /* CONFIG_ATH5K_DEBUG */
@@ -172,6 +168,7 @@ struct ath5k_softc {
 	struct tasklet_struct	txtq;		/* tx intr tasklet */
 	struct ath5k_led	tx_led;		/* tx led */
 
+	spinlock_t		block;		/* protects beacon */
 	struct ath5k_buf	*bbuf;		/* beacon buffer */
 	unsigned int		bhalq,		/* SW q for outgoing beacons */
 				bmisscount,	/* missed beacon transmits */
diff --git a/drivers/net/wireless/ath5k/debug.c b/drivers/net/wireless/ath5k/debug.c
index 41d5fa3..6fa6c8e 100644
--- a/drivers/net/wireless/ath5k/debug.c
+++ b/drivers/net/wireless/ath5k/debug.c
@@ -129,7 +129,7 @@ static struct reg regs[] = {
 	REG_STRUCT_INIT(AR5K_CPC1),
 	REG_STRUCT_INIT(AR5K_CPC2),
 	REG_STRUCT_INIT(AR5K_CPC3),
-	REG_STRUCT_INIT(AR5K_CPCORN),
+	REG_STRUCT_INIT(AR5K_CPCOVF),
 	REG_STRUCT_INIT(AR5K_RESET_CTL),
 	REG_STRUCT_INIT(AR5K_SLEEP_CTL),
 	REG_STRUCT_INIT(AR5K_INTPEND),
diff --git a/drivers/net/wireless/ath5k/debug.h b/drivers/net/wireless/ath5k/debug.h
index 2cf8d18..ffc5293 100644
--- a/drivers/net/wireless/ath5k/debug.h
+++ b/drivers/net/wireless/ath5k/debug.h
@@ -63,7 +63,6 @@
 
 struct ath5k_softc;
 struct ath5k_hw;
-struct ieee80211_hw_mode;
 struct sk_buff;
 struct ath5k_buf;
 
diff --git a/drivers/net/wireless/ath5k/hw.c b/drivers/net/wireless/ath5k/hw.c
index 4dab311..9c38943 100644
--- a/drivers/net/wireless/ath5k/hw.c
+++ b/drivers/net/wireless/ath5k/hw.c
@@ -31,13 +31,6 @@
 #include "base.h"
 #include "debug.h"
 
-/* Rate tables */
-static const struct ath5k_rate_table ath5k_rt_11a = AR5K_RATES_11A;
-static const struct ath5k_rate_table ath5k_rt_11b = AR5K_RATES_11B;
-static const struct ath5k_rate_table ath5k_rt_11g = AR5K_RATES_11G;
-static const struct ath5k_rate_table ath5k_rt_turbo = AR5K_RATES_TURBO;
-static const struct ath5k_rate_table ath5k_rt_xr = AR5K_RATES_XR;
-
 /* Prototypes */
 static int ath5k_hw_nic_reset(struct ath5k_hw *, u32);
 static int ath5k_hw_nic_wakeup(struct ath5k_hw *, int, bool);
@@ -139,6 +132,8 @@ static int ath5k_hw_post(struct ath5k_hw *ah)
 	for (c = 0; c < 2; c++) {
 
 		cur_reg = regs[c];
+
+		/* Save previous value */
 		init_val = ath5k_hw_reg_read(ah, cur_reg);
 
 		for (i = 0; i < 256; i++) {
@@ -170,6 +165,10 @@ static int ath5k_hw_post(struct ath5k_hw *ah)
 			var_pattern = 0x003b080f;
 			ath5k_hw_reg_write(ah, var_pattern, cur_reg);
 		}
+
+		/* Restore previous value */
+		ath5k_hw_reg_write(ah, init_val, cur_reg);
+
 	}
 
 	return 0;
@@ -287,67 +286,42 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version)
 	/* Identify the radio chip*/
 	if (ah->ah_version == AR5K_AR5210) {
 		ah->ah_radio = AR5K_RF5110;
+	/*
+	 * Register returns 0x0/0x04 for radio revision
+	 * so ath5k_hw_radio_revision doesn't parse the value
+	 * correctly. For now we are based on mac's srev to
+	 * identify RF2425 radio.
+	 */
+	} else if (srev == AR5K_SREV_VER_AR2425) {
+		ah->ah_radio = AR5K_RF2425;
+		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2425;
 	} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112) {
 		ah->ah_radio = AR5K_RF5111;
 		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5111;
 	} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC0) {
-
 		ah->ah_radio = AR5K_RF5112;
-
-		if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5112A) {
-			ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112;
-		} else {
-			ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
-		}
-
+		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112;
 	} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC1) {
 		ah->ah_radio = AR5K_RF2413;
-		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
+		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413;
 	} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_SC2) {
 		ah->ah_radio = AR5K_RF5413;
-		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
+		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413;
 	} else if (ah->ah_radio_5ghz_revision < AR5K_SREV_RAD_5133) {
-
 		/* AR5424 */
 		if (srev >= AR5K_SREV_VER_AR5424) {
 			ah->ah_radio = AR5K_RF5413;
-			ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5424;
+			ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413;
 		/* AR2424 */
 		} else {
 			ah->ah_radio = AR5K_RF2413; /* For testing */
-			ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112A;
+			ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413;
 		}
-
-	/*
-	 * Register returns 0x4 for radio revision
-	 * so ath5k_hw_radio_revision doesn't parse the value
-	 * correctly. For now we are based on mac's srev to
-	 * identify RF2425 radio.
-	 */
-	} else if (srev == AR5K_SREV_VER_AR2425) {
-		ah->ah_radio = AR5K_RF2425;
-		ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112;
 	}
-
 	ah->ah_phy = AR5K_PHY(0);
 
 	/*
-	 * Identify AR5212-based PCI-E cards
-	 * And write some initial settings.
-	 *
-	 * (doing a "strings" on ndis driver
-	 * -ar5211.sys- reveals the following
-	 * pci-e related functions:
-	 *
-	 * pcieClockReq
-	 * pcieRxErrNotify
-	 * pcieL1SKPEnable
-	 * pcieAspm
-	 * pcieDisableAspmOnRfWake
-	 * pciePowerSaveEnable
-	 *
-	 * I guess these point to ClockReq but
-	 * i'm not sure.)
+	 * Write PCI-E power save settings
 	 */
 #if (LINUX_VERSION_CODE < KERNEL_VERSION(2,6,24))
 	if ((ah->ah_version == AR5K_AR5212) && compat_is_pcie(pdev)) {
@@ -373,10 +347,15 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version)
 	if (ret)
 		goto err_free;
 
+	/* Write AR5K_PCICFG_UNK on 2112B and later chips */
+	if (ah->ah_radio_5ghz_revision > AR5K_SREV_RAD_2112B ||
+	srev > AR5K_SREV_VER_AR2413) {
+		ath5k_hw_reg_write(ah, AR5K_PCICFG_UNK, AR5K_PCICFG);
+	}
+
 	/*
 	 * Get card capabilities, values, ...
 	 */
-
 	ret = ath5k_eeprom_init(ah);
 	if (ret) {
 		ATH5K_ERR(sc, "unable to init EEPROM\n");
@@ -543,34 +522,6 @@ static int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial)
 }
 
 /*
- * Get the rate table for a specific operation mode
- */
-const struct ath5k_rate_table *ath5k_hw_get_rate_table(struct ath5k_hw *ah,
-		unsigned int mode)
-{
-	ATH5K_TRACE(ah->ah_sc);
-
-	if (!test_bit(mode, ah->ah_capabilities.cap_mode))
-		return NULL;
-
-	/* Get rate tables */
-	switch (mode) {
-	case AR5K_MODE_11A:
-		return &ath5k_rt_11a;
-	case AR5K_MODE_11A_TURBO:
-		return &ath5k_rt_turbo;
-	case AR5K_MODE_11B:
-		return &ath5k_rt_11b;
-	case AR5K_MODE_11G:
-		return &ath5k_rt_11g;
-	case AR5K_MODE_11G_TURBO:
-		return &ath5k_rt_xr;
-	}
-
-	return NULL;
-}
-
-/*
  * Free the ath5k_hw struct
  */
 void ath5k_hw_detach(struct ath5k_hw *ah)
@@ -640,45 +591,42 @@ static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw *ah,
 	return 0;
 }
 
+
+/*
+ * index into rates for control rates, we can set it up like this because
+ * this is only used for AR5212 and we know it supports G mode
+ */
+static int control_rates[] =
+	{ 0, 1, 1, 1, 4, 4, 6, 6, 8, 8, 8, 8 };
+
 /**
  * ath5k_hw_write_rate_duration - set rate duration during hw resets
  *
  * @ah: the &struct ath5k_hw
  * @mode: one of enum ath5k_driver_mode
  *
- * Write the rate duration table for the current mode upon hw reset. This
- * is a helper for ath5k_hw_reset(). It seems all this is doing is setting
- * an ACK timeout for the hardware for the current mode for each rate. The
- * rates which are capable of short preamble (802.11b rates 2Mbps, 5.5Mbps,
- * and 11Mbps) have another register for the short preamble ACK timeout
- * calculation.
- *
+ * Write the rate duration table upon hw reset. This is a helper for
+ * ath5k_hw_reset(). It seems all this is doing is setting an ACK timeout for
+ * the hardware for the current mode for each rate. The rates which are capable
+ * of short preamble (802.11b rates 2Mbps, 5.5Mbps, and 11Mbps) have another
+ * register for the short preamble ACK timeout calculation.
  */
 static inline void ath5k_hw_write_rate_duration(struct ath5k_hw *ah,
        unsigned int mode)
 {
 	struct ath5k_softc *sc = ah->ah_sc;
-	const struct ath5k_rate_table *rt;
-	struct ieee80211_rate srate = {};
+	struct ieee80211_rate *rate;
 	unsigned int i;
 
-	/* Get rate table for the current operating mode */
-	rt = ath5k_hw_get_rate_table(ah, mode);
-
 	/* Write rate duration table */
-	for (i = 0; i < rt->rate_count; i++) {
-		const struct ath5k_rate *rate, *control_rate;
-
+	for (i = 0; i < sc->sbands[IEEE80211_BAND_2GHZ].n_bitrates; i++) {
 		u32 reg;
 		u16 tx_time;
 
-		rate = &rt->rates[i];
-		control_rate = &rt->rates[rate->control_rate];
+		rate = &sc->sbands[IEEE80211_BAND_2GHZ].bitrates[control_rates[i]];
 
 		/* Set ACK timeout */
-		reg = AR5K_RATE_DUR(rate->rate_code);
-
-		srate.bitrate = control_rate->rate_kbps/100;
+		reg = AR5K_RATE_DUR(rate->hw_value);
 
 		/* An ACK frame consists of 10 bytes. If you add the FCS,
 		 * which ieee80211_generic_frame_duration() adds,
@@ -687,11 +635,11 @@ static inline void ath5k_hw_write_rate_duration(struct ath5k_hw *ah,
 		 * ieee80211_duration() for a brief description of
 		 * what rate we should choose to TX ACKs. */
 		tx_time = le16_to_cpu(ieee80211_generic_frame_duration(sc->hw,
-							sc->vif, 10, &srate));
+							sc->vif, 10, rate));
 
 		ath5k_hw_reg_write(ah, tx_time, reg);
 
-		if (!HAS_SHPREAMBLE(i))
+		if (!(rate->flags & IEEE80211_RATE_SHORT_PREAMBLE))
 			continue;
 
 		/*
@@ -851,27 +799,41 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 		 * Write some more initial register settings
 		 */
 		if (ah->ah_version == AR5K_AR5212) {
-			ath5k_hw_reg_write(ah, 0x0002a002, AR5K_PHY(11));
+			ath5k_hw_reg_write(ah, 0x0002a002, 0x982c);
 
 			if (channel->hw_value == CHANNEL_G)
 				if (ah->ah_mac_srev < AR5K_SREV_VER_AR2413)
 					ath5k_hw_reg_write(ah, 0x00f80d80,
-						AR5K_PHY(83));
+								0x994c);
 				else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2424)
 					ath5k_hw_reg_write(ah, 0x00380140,
-						AR5K_PHY(83));
+								0x994c);
 				else if (ah->ah_mac_srev < AR5K_SREV_VER_AR2425)
 					ath5k_hw_reg_write(ah, 0x00fc0ec0,
-						AR5K_PHY(83));
+								0x994c);
 				else /* 2425 */
 					ath5k_hw_reg_write(ah, 0x00fc0fc0,
-						AR5K_PHY(83));
+								0x994c);
 			else
-				ath5k_hw_reg_write(ah, 0x00000000,
-					AR5K_PHY(83));
-
-			ath5k_hw_reg_write(ah, 0x000009b5, 0xa228);
-			ath5k_hw_reg_write(ah, 0x0000000f, 0x8060);
+				ath5k_hw_reg_write(ah, 0x00000000, 0x994c);
+
+			/* Some bits are disabled here, we know nothing about
+			 * register 0xa228 yet, most of the times this ends up
+			 * with a value 0x9b5 -haven't seen any dump with
+			 * a different value- */
+			/* Got this from decompiling binary HAL */
+			data = ath5k_hw_reg_read(ah, 0xa228);
+			data &= 0xfffffdff;
+			ath5k_hw_reg_write(ah, data, 0xa228);
+
+			data = ath5k_hw_reg_read(ah, 0xa228);
+			data &= 0xfffe03ff;
+			ath5k_hw_reg_write(ah, data, 0xa228);
+			data = 0;
+
+			/* Just write 0x9b5 ? */
+			/* ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); */
+			ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK);
 			ath5k_hw_reg_write(ah, 0x00000000, 0xa254);
 			ath5k_hw_reg_write(ah, 0x0000000e, AR5K_PHY_SCAL);
 		}
@@ -887,6 +849,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 			else
 				data = 0xffb80d20;
 			ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL);
+			data = 0;
 		}
 
 		/*
@@ -906,7 +869,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 
 		/*
 		 * Write RF registers
-		 * TODO:Does this work on 5211 (5111) ?
 		 */
 		ret = ath5k_hw_rfregs(ah, channel, mode);
 		if (ret)
@@ -943,7 +905,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 			return ret;
 
 		/* Set antenna mode */
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x44),
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_ANT_CTL,
 			ah->ah_antenna[ee_mode][0], 0xfffffc06);
 
 		/*
@@ -973,15 +935,15 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 
 		ath5k_hw_reg_write(ah,
 			AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]),
-			AR5K_PHY(0x5a));
+			AR5K_PHY_NFTHRES);
 
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x11),
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_SETTLING,
 			(ee->ee_switch_settling[ee_mode] << 7) & 0x3f80,
 			0xffffc07f);
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x12),
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_GAIN,
 			(ee->ee_ant_tx_rx[ee_mode] << 12) & 0x3f000,
 			0xfffc0fff);
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x14),
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_DESIRED_SIZE,
 			(ee->ee_adc_desired_size[ee_mode] & 0x00ff) |
 			((ee->ee_pga_desired_size[ee_mode] << 8) & 0xff00),
 			0xffff0000);
@@ -990,13 +952,13 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 			(ee->ee_tx_end2xpa_disable[ee_mode] << 24) |
 			(ee->ee_tx_end2xpa_disable[ee_mode] << 16) |
 			(ee->ee_tx_frm2xpa_enable[ee_mode] << 8) |
-			(ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY(0x0d));
+			(ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4);
 
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x0a),
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_RF_CTL3,
 			ee->ee_tx_end2xlna_enable[ee_mode] << 8, 0xffff00ff);
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x19),
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_NF,
 			(ee->ee_thr_62[ee_mode] << 12) & 0x7f000, 0xfff80fff);
-		AR5K_REG_MASKED_BITS(ah, AR5K_PHY(0x49), 4, 0xffffff01);
+		AR5K_REG_MASKED_BITS(ah, AR5K_PHY_OFDM_SELFCORR, 4, 0xffffff01);
 
 		AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
 		    AR5K_PHY_IQ_CORR_ENABLE |
@@ -1075,7 +1037,8 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 	ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT);
 
 	/*
-	 * 5111/5112 Specific
+	 * On 5211+ read activation -> rx delay
+	 * and use it.
 	 */
 	if (ah->ah_version != AR5K_AR5210) {
 		data = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) &
@@ -1083,40 +1046,77 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 		data = (channel->hw_value & CHANNEL_CCK) ?
 			((data << 2) / 22) : (data / 10);
 
-		udelay(100 + data);
+		udelay(100 + (2 * data));
+		data = 0;
 	} else {
 		mdelay(1);
 	}
 
 	/*
-	 * Enable calibration and wait until completion
+	 * Perform ADC test (?)
+	 */
+	data = ath5k_hw_reg_read(ah, AR5K_PHY_TST1);
+	ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1);
+	for (i = 0; i <= 20; i++) {
+		if (!(ath5k_hw_reg_read(ah, AR5K_PHY_ADC_TEST) & 0x10))
+			break;
+		udelay(200);
+	}
+	ath5k_hw_reg_write(ah, data, AR5K_PHY_TST1);
+	data = 0;
+
+	/*
+	 * Start automatic gain calibration
+	 *
+	 * During AGC calibration RX path is re-routed to
+	 * a signal detector so we don't receive anything.
+	 *
+	 * This method is used to calibrate some static offsets
+	 * used together with on-the fly I/Q calibration (the
+	 * one performed via ath5k_hw_phy_calibrate), that doesn't
+	 * interrupt rx path.
+	 *
+	 * If we are in a noisy environment AGC calibration may time
+	 * out.
 	 */
 	AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
 				AR5K_PHY_AGCCTL_CAL);
 
+	/* At the same time start I/Q calibration for QAM constellation
+	 * -no need for CCK- */
+	ah->ah_calibration = false;
+	if (!(mode == AR5K_MODE_11B)) {
+		ah->ah_calibration = true;
+		AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
+				AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
+				AR5K_PHY_IQ_RUN);
+	}
+
+	/* Wait for gain calibration to finish (we check for I/Q calibration
+	 * during ath5k_phy_calibrate) */
 	if (ath5k_hw_register_timeout(ah, AR5K_PHY_AGCCTL,
 			AR5K_PHY_AGCCTL_CAL, 0, false)) {
-		ATH5K_ERR(ah->ah_sc, "calibration timeout (%uMHz)\n",
+		ATH5K_ERR(ah->ah_sc, "gain calibration timeout (%uMHz)\n",
 			channel->center_freq);
 		return -EAGAIN;
 	}
 
+	/*
+	 * Start noise floor calibration
+	 *
+	 * If we run NF calibration before AGC, it always times out.
+	 * Binary HAL starts NF and AGC calibration at the same time
+	 * and only waits for AGC to finish. I believe that's wrong because
+	 * during NF calibration, rx path is also routed to a detector, so if
+	 * it doesn't finish we won't have RX.
+	 *
+	 * XXX: Find an interval that's OK for all cards...
+	 */
 	ret = ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
 	if (ret)
 		return ret;
 
-	ah->ah_calibration = false;
-
-	/* A and G modes can use QAM modulation which requires enabling
-	 * I and Q calibration. Don't bother in B mode. */
-	if (!(mode == AR5K_MODE_11B)) {
-		ah->ah_calibration = true;
-		AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
-				AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
-		AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ,
-				AR5K_PHY_IQ_RUN);
-	}
-
 	/*
 	 * Reset queues and start beacon timers at the end of the reset routine
 	 */
@@ -1166,6 +1166,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum ieee80211_if_types op_mode,
 		ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK);
 		ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY);
 		ath5k_hw_reg_write(ah, ah->ah_phy_spending, AR5K_PHY_SPENDING);
+
+		data = ath5k_hw_reg_read(ah, AR5K_USEC_5211) & 0xffffc07f ;
+		data |= (ah->ah_phy_spending == AR5K_PHY_SPENDING_18) ?
+						0x00000f80 : 0x00001380 ;
+		ath5k_hw_reg_write(ah, data, AR5K_USEC_5211);
+		data = 0;
 	}
 
 	if (ah->ah_version == AR5K_AR5212) {
@@ -1238,7 +1244,7 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode,
 		bool set_chip, u16 sleep_duration)
 {
 	unsigned int i;
-	u32 staid;
+	u32 staid, data;
 
 	ATH5K_TRACE(ah->ah_sc);
 	staid = ath5k_hw_reg_read(ah, AR5K_STA_ID1);
@@ -1250,7 +1256,8 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode,
 	case AR5K_PM_NETWORK_SLEEP:
 		if (set_chip)
 			ath5k_hw_reg_write(ah,
-				AR5K_SLEEP_CTL_SLE | sleep_duration,
+				AR5K_SLEEP_CTL_SLE_ALLOW |
+				sleep_duration,
 				AR5K_SLEEP_CTL);
 
 		staid |= AR5K_STA_ID1_PWR_SV;
@@ -1265,13 +1272,24 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode,
 		break;
 
 	case AR5K_PM_AWAKE:
+
+		staid &= ~AR5K_STA_ID1_PWR_SV;
+
 		if (!set_chip)
 			goto commit;
 
-		ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_WAKE,
-				AR5K_SLEEP_CTL);
+		/* Preserve sleep duration */
+		data = ath5k_hw_reg_read(ah, AR5K_SLEEP_CTL);
+		if( data & 0xffc00000 ){
+			data = 0;
+		} else {
+			data = data & 0xfffcffff;
+		}
+
+		ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL);
+		udelay(15);
 
-		for (i = 5000; i > 0; i--) {
+		for (i = 50; i > 0; i--) {
 			/* Check if the chip did wake up */
 			if ((ath5k_hw_reg_read(ah, AR5K_PCICFG) &
 					AR5K_PCICFG_SPWR_DN) == 0)
@@ -1279,15 +1297,13 @@ int ath5k_hw_set_power(struct ath5k_hw *ah, enum ath5k_power_mode mode,
 
 			/* Wait a bit and retry */
 			udelay(200);
-			ath5k_hw_reg_write(ah, AR5K_SLEEP_CTL_SLE_WAKE,
-				AR5K_SLEEP_CTL);
+			ath5k_hw_reg_write(ah, data, AR5K_SLEEP_CTL);
 		}
 
 		/* Fail if the chip didn't wake up */
 		if (i <= 0)
 			return -EIO;
 
-		staid &= ~AR5K_STA_ID1_PWR_SV;
 		break;
 
 	default:
@@ -1316,6 +1332,7 @@ void ath5k_hw_start_rx(struct ath5k_hw *ah)
 {
 	ATH5K_TRACE(ah->ah_sc);
 	ath5k_hw_reg_write(ah, AR5K_CR_RXE, AR5K_CR);
+	ath5k_hw_reg_read(ah, AR5K_CR);
 }
 
 /*
@@ -1402,6 +1419,7 @@ int ath5k_hw_tx_start(struct ath5k_hw *ah, unsigned int queue)
 		}
 		/* Start queue */
 		ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
+		ath5k_hw_reg_read(ah, AR5K_CR);
 	} else {
 		/* Return if queue is disabled */
 		if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXD, queue))
@@ -1452,6 +1470,7 @@ int ath5k_hw_stop_tx_dma(struct ath5k_hw *ah, unsigned int queue)
 
 		/* Stop queue */
 		ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
+		ath5k_hw_reg_read(ah, AR5K_CR);
 	} else {
 		/*
 		 * Schedule TX disable and wait until queue is empty
@@ -1468,6 +1487,8 @@ int ath5k_hw_stop_tx_dma(struct ath5k_hw *ah, unsigned int queue)
 
 		/* Clear register */
 		ath5k_hw_reg_write(ah, 0, AR5K_QCU_TXD);
+		if (pending)
+			return -EBUSY;
 	}
 
 	/* TODO: Check for success else return error */
@@ -1696,6 +1717,7 @@ enum ath5k_int ath5k_hw_set_intr(struct ath5k_hw *ah, enum ath5k_int new_mask)
 	 * (they will be re-enabled afterwards).
 	 */
 	ath5k_hw_reg_write(ah, AR5K_IER_DISABLE, AR5K_IER);
+	ath5k_hw_reg_read(ah, AR5K_IER);
 
 	old_mask = ah->ah_imr;
 
@@ -1728,6 +1750,7 @@ enum ath5k_int ath5k_hw_set_intr(struct ath5k_hw *ah, enum ath5k_int new_mask)
 
 	/* ..re-enable interrupts */
 	ath5k_hw_reg_write(ah, AR5K_IER_ENABLE, AR5K_IER);
+	ath5k_hw_reg_read(ah, AR5K_IER);
 
 	return old_mask;
 }
@@ -2338,6 +2361,7 @@ int ath5k_hw_set_opmode(struct ath5k_hw *ah)
 		break;
 
 	case IEEE80211_IF_TYPE_AP:
+	case IEEE80211_IF_TYPE_MESH_POINT:
 		pcu_reg |= AR5K_STA_ID1_AP | AR5K_STA_ID1_RTS_DEF_ANTENNA |
 			(ah->ah_version == AR5K_AR5210 ?
 				AR5K_STA_ID1_NO_PSPOLL : 0);
@@ -3371,11 +3395,13 @@ int ath5k_hw_reset_tx_queue(struct ath5k_hw *ah, unsigned int queue)
 		ath5k_hw_reg_write(ah, ah->ah_turbo ?
 			AR5K_INIT_PROTO_TIME_CNTRL_TURBO :
 			AR5K_INIT_PROTO_TIME_CNTRL, AR5K_IFS1);
-		/* Set PHY register 0x9844 (??) */
+		/* Set AR5K_PHY_SETTLING */
 		ath5k_hw_reg_write(ah, ah->ah_turbo ?
-			(ath5k_hw_reg_read(ah, AR5K_PHY(17)) & ~0x7F) | 0x38 :
-			(ath5k_hw_reg_read(ah, AR5K_PHY(17)) & ~0x7F) | 0x1C,
-			AR5K_PHY(17));
+			(ath5k_hw_reg_read(ah, AR5K_PHY_SETTLING) & ~0x7F)
+			| 0x38 :
+			(ath5k_hw_reg_read(ah, AR5K_PHY_SETTLING) & ~0x7F)
+			| 0x1C,
+			AR5K_PHY_SETTLING);
 		/* Set Frame Control Register */
 		ath5k_hw_reg_write(ah, ah->ah_turbo ?
 			(AR5K_PHY_FRAME_CTL_INI | AR5K_PHY_TURBO_MODE |
@@ -3496,7 +3522,7 @@ int ath5k_hw_reset_tx_queue(struct ath5k_hw *ah, unsigned int queue)
 			if (tq->tqi_flags & AR5K_TXQ_FLAG_RDYTIME_EXP_POLICY_ENABLE)
 				AR5K_REG_ENABLE_BITS(ah,
 					AR5K_QUEUE_MISC(queue),
-					AR5K_QCU_MISC_TXE);
+					AR5K_QCU_MISC_RDY_VEOL_POLICY);
 		}
 
 		if (tq->tqi_flags & AR5K_TXQ_FLAG_BACKOFF_DISABLE)
diff --git a/drivers/net/wireless/ath5k/initvals.c b/drivers/net/wireless/ath5k/initvals.c
index 04c84e9..2806b21 100644
--- a/drivers/net/wireless/ath5k/initvals.c
+++ b/drivers/net/wireless/ath5k/initvals.c
@@ -489,7 +489,7 @@ static const struct ath5k_ini ar5212_ini[] = {
 	{ AR5K_QUEUE_TXDP(9),	0x00000000 },
 	{ AR5K_DCU_FP,		0x00000000 },
 	{ AR5K_DCU_TXP,		0x00000000 },
-	{ AR5K_DCU_TX_FILTER,	0x00000000 },
+	{ AR5K_DCU_TX_FILTER_0_BASE,	0x00000000 },
 	/* Unknown table */
 	{ 0x1078, 0x00000000 },
 	{ 0x10b8, 0x00000000 },
@@ -679,7 +679,7 @@ static const struct ath5k_ini ar5212_ini[] = {
 	{ AR5K_PHY(645), 0x00106c10 },
 	{ AR5K_PHY(646), 0x009c4060 },
 	{ AR5K_PHY(647), 0x1483800a },
-	/* { AR5K_PHY(648), 0x018830c6 },*/ /* 2413 */
+	/* { AR5K_PHY(648), 0x018830c6 },*/ /* 2413/2425 */
 	{ AR5K_PHY(648), 0x01831061 },
 	{ AR5K_PHY(649), 0x00000400 },
 	/*{ AR5K_PHY(650), 0x000001b5 },*/
diff --git a/drivers/net/wireless/ath5k/phy.c b/drivers/net/wireless/ath5k/phy.c
index afd8689..fa0d47f 100644
--- a/drivers/net/wireless/ath5k/phy.c
+++ b/drivers/net/wireless/ath5k/phy.c
@@ -1020,6 +1020,74 @@ static const struct ath5k_ini_rfgain rfgain_2413[] = {
 	{ AR5K_RF_GAIN(63), { 0x000000f9 } },
 };
 
+/* Initial RF Gain settings for RF2425 */
+static const struct ath5k_ini_rfgain rfgain_2425[] = {
+	{ AR5K_RF_GAIN(0), { 0x00000000 } },
+	{ AR5K_RF_GAIN(1), { 0x00000040 } },
+	{ AR5K_RF_GAIN(2), { 0x00000080 } },
+	{ AR5K_RF_GAIN(3), { 0x00000181 } },
+	{ AR5K_RF_GAIN(4), { 0x000001c1 } },
+	{ AR5K_RF_GAIN(5), { 0x00000001 } },
+	{ AR5K_RF_GAIN(6), { 0x00000041 } },
+	{ AR5K_RF_GAIN(7), { 0x00000081 } },
+	{ AR5K_RF_GAIN(8), { 0x00000188 } },
+	{ AR5K_RF_GAIN(9), { 0x000001c8 } },
+	{ AR5K_RF_GAIN(10), { 0x00000008 } },
+	{ AR5K_RF_GAIN(11), { 0x00000048 } },
+	{ AR5K_RF_GAIN(12), { 0x00000088 } },
+	{ AR5K_RF_GAIN(13), { 0x00000189 } },
+	{ AR5K_RF_GAIN(14), { 0x000001c9 } },
+	{ AR5K_RF_GAIN(15), { 0x00000009 } },
+	{ AR5K_RF_GAIN(16), { 0x00000049 } },
+	{ AR5K_RF_GAIN(17), { 0x00000089 } },
+	{ AR5K_RF_GAIN(18), { 0x000001b0 } },
+	{ AR5K_RF_GAIN(19), { 0x000001f0 } },
+	{ AR5K_RF_GAIN(20), { 0x00000030 } },
+	{ AR5K_RF_GAIN(21), { 0x00000070 } },
+	{ AR5K_RF_GAIN(22), { 0x00000171 } },
+	{ AR5K_RF_GAIN(23), { 0x000001b1 } },
+	{ AR5K_RF_GAIN(24), { 0x000001f1 } },
+	{ AR5K_RF_GAIN(25), { 0x00000031 } },
+	{ AR5K_RF_GAIN(26), { 0x00000071 } },
+	{ AR5K_RF_GAIN(27), { 0x000001b8 } },
+	{ AR5K_RF_GAIN(28), { 0x000001f8 } },
+	{ AR5K_RF_GAIN(29), { 0x00000038 } },
+	{ AR5K_RF_GAIN(30), { 0x00000078 } },
+	{ AR5K_RF_GAIN(31), { 0x000000b8 } },
+	{ AR5K_RF_GAIN(32), { 0x000001b9 } },
+	{ AR5K_RF_GAIN(33), { 0x000001f9 } },
+	{ AR5K_RF_GAIN(34), { 0x00000039 } },
+	{ AR5K_RF_GAIN(35), { 0x00000079 } },
+	{ AR5K_RF_GAIN(36), { 0x000000b9 } },
+	{ AR5K_RF_GAIN(37), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(38), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(39), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(40), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(41), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(42), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(43), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(44), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(45), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(46), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(47), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(48), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(49), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(50), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(51), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(52), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(53), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(54), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(55), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(56), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(57), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(58), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(59), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(60), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(61), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(62), { 0x000000f9 } },
+	{ AR5K_RF_GAIN(63), { 0x000000f9 } },
+};
+
 static const struct ath5k_gain_opt rfgain_opt_5112 = {
 	1,
 	8,
@@ -1588,8 +1656,8 @@ int ath5k_hw_rfgain(struct ath5k_hw *ah, unsigned int freq)
 		freq = 0; /* only 2Ghz */
 		break;
 	case AR5K_RF2425:
-		ath5k_rfg = rfgain_2413;
-		size = ARRAY_SIZE(rfgain_2413);
+		ath5k_rfg = rfgain_2425;
+		size = ARRAY_SIZE(rfgain_2425);
 		freq = 0; /* only 2Ghz */
 		break;
 	default:
@@ -1830,9 +1898,6 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah,
 	data = data0 = data1 = data2 = 0;
 	c = channel->center_freq;
 
-	/*
-	 * Set the channel on the RF5112 or newer
-	 */
 	if (c < 4800) {
 		if (!((c - 2224) % 5)) {
 			data0 = ((2 * (c - 704)) - 3040) / 10;
@@ -1844,7 +1909,7 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah,
 			return -EINVAL;
 
 		data0 = ath5k_hw_bitswap((data0 << 2) & 0xff, 8);
-	} else {
+	} else if ((c - (c % 5)) != 2 || c > 5435) {
 		if (!(c % 20) && c >= 5120) {
 			data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8);
 			data2 = ath5k_hw_bitswap(3, 2);
@@ -1856,6 +1921,9 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah,
 			data2 = ath5k_hw_bitswap(1, 2);
 		} else
 			return -EINVAL;
+	} else {
+		data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8);
+		data2 = ath5k_hw_bitswap(0, 2);
 	}
 
 	data = (data0 << 4) | (data1 << 1) | (data2 << 2) | 0x1001;
@@ -1867,6 +1935,45 @@ static int ath5k_hw_rf5112_channel(struct ath5k_hw *ah,
 }
 
 /*
+ * Set the channel on the RF2425
+ */
+static int ath5k_hw_rf2425_channel(struct ath5k_hw *ah,
+		struct ieee80211_channel *channel)
+{
+	u32 data, data0, data2;
+	u16 c;
+
+	data = data0 = data2 = 0;
+	c = channel->center_freq;
+
+	if (c < 4800) {
+		data0 = ath5k_hw_bitswap((c - 2272), 8);
+		data2 = 0;
+	/* ? 5GHz ? */
+	} else if ((c - (c % 5)) != 2 || c > 5435) {
+		if (!(c % 20) && c < 5120)
+			data0 = ath5k_hw_bitswap(((c - 4800) / 20 << 2), 8);
+		else if (!(c % 10))
+			data0 = ath5k_hw_bitswap(((c - 4800) / 10 << 1), 8);
+		else if (!(c % 5))
+			data0 = ath5k_hw_bitswap((c - 4800) / 5, 8);
+		else
+			return -EINVAL;
+		data2 = ath5k_hw_bitswap(1, 2);
+	} else {
+		data0 = ath5k_hw_bitswap((10 * (c - 2) - 4800) / 25 + 1, 8);
+		data2 = ath5k_hw_bitswap(0, 2);
+	}
+
+	data = (data0 << 4) | data2 << 2 | 0x1001;
+
+	ath5k_hw_reg_write(ah, data & 0xff, AR5K_RF_BUFFER);
+	ath5k_hw_reg_write(ah, (data >> 8) & 0x7f, AR5K_RF_BUFFER_CONTROL_5);
+
+	return 0;
+}
+
+/*
  * Set a channel on the radio chip
  */
 int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel)
@@ -1895,6 +2002,9 @@ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel)
 	case AR5K_RF5111:
 		ret = ath5k_hw_rf5111_channel(ah, channel);
 		break;
+	case AR5K_RF2425:
+		ret = ath5k_hw_rf2425_channel(ah, channel);
+		break;
 	default:
 		ret = ath5k_hw_rf5112_channel(ah, channel);
 		break;
@@ -1903,6 +2013,15 @@ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel)
 	if (ret)
 		return ret;
 
+	/* Set JAPAN setting for channel 14 */
+	if (channel->center_freq == 2484) {
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL,
+				AR5K_PHY_CCKTXCTL_JAPAN);
+	} else {
+		AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_CCKTXCTL,
+				AR5K_PHY_CCKTXCTL_WORLD);
+	}
+
 	ah->ah_current_channel.center_freq = channel->center_freq;
 	ah->ah_current_channel.hw_value = channel->hw_value;
 	ah->ah_turbo = channel->hw_value == CHANNEL_T ? true : false;
@@ -1933,6 +2052,8 @@ int ath5k_hw_channel(struct ath5k_hw *ah, struct ieee80211_channel *channel)
  * http://patft.uspto.gov/netacgi/nph-Parser?Sect1=PTO1&Sect2=HITOFF&d=PALL \
  * &p=1&u=%2Fnetahtml%2FPTO%2Fsrchnum.htm&r=1&f=G&l=50&s1=7245893.PN.&OS=PN/7
  *
+ * XXX: Since during noise floor calibration antennas are detached according to
+ * the patent, we should stop tx queues here.
  */
 int
 ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq)
@@ -1942,7 +2063,7 @@ ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq)
 	s32 noise_floor;
 
 	/*
-	 * Enable noise floor calibration and wait until completion
+	 * Enable noise floor calibration
 	 */
 	AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL,
 				AR5K_PHY_AGCCTL_NF);
@@ -1952,7 +2073,7 @@ ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq)
 	if (ret) {
 		ATH5K_ERR(ah->ah_sc,
 			"noise floor calibration timeout (%uMHz)\n", freq);
-		return ret;
+		return -EAGAIN;
 	}
 
 	/* Wait until the noise floor is calibrated and read the value */
@@ -1974,7 +2095,7 @@ ath5k_hw_noise_floor_calibration(struct ath5k_hw *ah, short freq)
 	if (noise_floor > AR5K_TUNE_NOISE_FLOOR) {
 		ATH5K_ERR(ah->ah_sc,
 			"noise floor calibration failed (%uMHz)\n", freq);
-		return -EIO;
+		return -EAGAIN;
 	}
 
 	ah->ah_noise_floor = noise_floor;
@@ -2087,38 +2208,66 @@ static int ath5k_hw_rf5110_calibrate(struct ath5k_hw *ah,
 }
 
 /*
- * Perform a PHY calibration on RF5111/5112
+ * Perform a PHY calibration on RF5111/5112 and newer chips
  */
 static int ath5k_hw_rf511x_calibrate(struct ath5k_hw *ah,
 		struct ieee80211_channel *channel)
 {
 	u32 i_pwr, q_pwr;
 	s32 iq_corr, i_coff, i_coffd, q_coff, q_coffd;
+	int i;
 	ATH5K_TRACE(ah->ah_sc);
 
 	if (!ah->ah_calibration ||
-			ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN)
+		ath5k_hw_reg_read(ah, AR5K_PHY_IQ) & AR5K_PHY_IQ_RUN)
 		goto done;
 
-	ah->ah_calibration = false;
+	/* Calibration has finished, get the results and re-run */
+	for (i = 0; i <= 10; i++) {
+		iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
+		i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
+		q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q);
+	}
 
-	iq_corr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_CORR);
-	i_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_I);
-	q_pwr = ath5k_hw_reg_read(ah, AR5K_PHY_IQRES_CAL_PWR_Q);
 	i_coffd = ((i_pwr >> 1) + (q_pwr >> 1)) >> 7;
-	q_coffd = q_pwr >> 6;
+	q_coffd = q_pwr >> 7;
 
+	/* No correction */
 	if (i_coffd == 0 || q_coffd == 0)
 		goto done;
 
 	i_coff = ((-iq_corr) / i_coffd) & 0x3f;
-	q_coff = (((s32)i_pwr / q_coffd) - 64) & 0x1f;
 
-	/* Commit new IQ value */
+	/* Boundary check */
+	if (i_coff > 31)
+		i_coff = 31;
+	if (i_coff < -32)
+		i_coff = -32;
+
+	q_coff = (((s32)i_pwr / q_coffd) - 128) & 0x1f;
+
+	/* Boundary check */
+	if (q_coff > 15)
+		q_coff = 15;
+	if (q_coff < -16)
+		q_coff = -16;
+
+	/* Commit new I/Q value */
 	AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_CORR_ENABLE |
 		((u32)q_coff) | ((u32)i_coff << AR5K_PHY_IQ_CORR_Q_I_COFF_S));
 
+	/* Re-enable calibration -if we don't we'll commit
+	 * the same values again and again */
+	AR5K_REG_WRITE_BITS(ah, AR5K_PHY_IQ,
+			AR5K_PHY_IQ_CAL_NUM_LOG_MAX, 15);
+	AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, AR5K_PHY_IQ_RUN);
+
 done:
+
+	/* TODO: Separate noise floor calibration from I/Q calibration
+	 * since noise floor calibration interrupts rx path while I/Q
+	 * calibration doesn't. We don't need to run noise floor calibration
+	 * as often as I/Q calibration.*/
 	ath5k_hw_noise_floor_calibration(ah, channel->center_freq);
 
 	/* Request RF gain */
diff --git a/drivers/net/wireless/ath5k/reg.h b/drivers/net/wireless/ath5k/reg.h
index 30629b3..7562bf1 100644
--- a/drivers/net/wireless/ath5k/reg.h
+++ b/drivers/net/wireless/ath5k/reg.h
@@ -53,7 +53,7 @@
 #define AR5K_CR_TXD0	0x00000008	/* TX Disable for queue 0 on 5210 */
 #define AR5K_CR_TXD1	0x00000010	/* TX Disable for queue 1 on 5210 */
 #define	AR5K_CR_RXD	0x00000020	/* RX Disable */
-#define	AR5K_CR_SWI	0x00000040
+#define	AR5K_CR_SWI	0x00000040	/* Software Interrupt */
 
 /*
  * RX Descriptor Pointer register
@@ -65,19 +65,19 @@
  */
 #define	AR5K_CFG		0x0014			/* Register Address */
 #define	AR5K_CFG_SWTD		0x00000001	/* Byte-swap TX descriptor (for big endian archs) */
-#define	AR5K_CFG_SWTB		0x00000002	/* Byte-swap TX buffer (?) */
+#define	AR5K_CFG_SWTB		0x00000002	/* Byte-swap TX buffer */
 #define	AR5K_CFG_SWRD		0x00000004	/* Byte-swap RX descriptor */
-#define	AR5K_CFG_SWRB		0x00000008	/* Byte-swap RX buffer (?) */
-#define	AR5K_CFG_SWRG		0x00000010	/* Byte-swap Register values (?) */
-#define AR5K_CFG_ADHOC		0x00000020 	/* [5211+] */
+#define	AR5K_CFG_SWRB		0x00000008	/* Byte-swap RX buffer */
+#define	AR5K_CFG_SWRG		0x00000010	/* Byte-swap Register access */
+#define AR5K_CFG_ADHOC		0x00000020 	/* AP/Adhoc indication [5211+] */
 #define AR5K_CFG_PHY_OK		0x00000100	/* [5211+] */
 #define AR5K_CFG_EEBS		0x00000200	/* EEPROM is busy */
-#define	AR5K_CFG_CLKGD		0x00000400	/* Clock gated (?) */
+#define	AR5K_CFG_CLKGD		0x00000400	/* Clock gated (Disable dynamic clock) */
 #define AR5K_CFG_TXCNT		0x00007800	/* Tx frame count (?) [5210] */
 #define AR5K_CFG_TXCNT_S	11
 #define AR5K_CFG_TXFSTAT	0x00008000	/* Tx frame status (?) [5210] */
 #define AR5K_CFG_TXFSTRT	0x00010000	/* [5210] */
-#define	AR5K_CFG_PCI_THRES	0x00060000	/* [5211+] */
+#define	AR5K_CFG_PCI_THRES	0x00060000	/* PCI Master req q threshold [5211+] */
 #define	AR5K_CFG_PCI_THRES_S	17
 
 /*
@@ -162,35 +162,40 @@
 /*
  * Transmit configuration register
  */
-#define AR5K_TXCFG		0x0030			/* Register Address */
-#define AR5K_TXCFG_SDMAMR	0x00000007	/* DMA size */
-#define AR5K_TXCFG_SDMAMR_S	0
-#define AR5K_TXCFG_B_MODE	0x00000008	/* Set b mode for 5111 (enable 2111) */
-#define AR5K_TXCFG_TXFSTP	0x00000008	/* TX DMA full Stop [5210] */
-#define AR5K_TXCFG_TXFULL	0x000003f0	/* TX Triger level mask */
-#define AR5K_TXCFG_TXFULL_S	4
-#define AR5K_TXCFG_TXFULL_0B	0x00000000
-#define AR5K_TXCFG_TXFULL_64B	0x00000010
-#define AR5K_TXCFG_TXFULL_128B	0x00000020
-#define AR5K_TXCFG_TXFULL_192B	0x00000030
-#define AR5K_TXCFG_TXFULL_256B	0x00000040
-#define AR5K_TXCFG_TXCONT_EN	0x00000080
-#define AR5K_TXCFG_DMASIZE	0x00000100	/* Flag for passing DMA size [5210] */
-#define AR5K_TXCFG_JUMBO_TXE	0x00000400	/* Enable jumbo frames transmition (?) [5211+] */
-#define AR5K_TXCFG_RTSRND	0x00001000	/* [5211+] */
-#define AR5K_TXCFG_FRMPAD_DIS	0x00002000	/* [5211+] */
-#define AR5K_TXCFG_RDY_DIS	0x00004000	/* [5211+] */
+#define AR5K_TXCFG			0x0030			/* Register Address */
+#define AR5K_TXCFG_SDMAMR		0x00000007	/* DMA size (read) */
+#define AR5K_TXCFG_SDMAMR_S		0
+#define AR5K_TXCFG_B_MODE		0x00000008	/* Set b mode for 5111 (enable 2111) */
+#define AR5K_TXCFG_TXFSTP		0x00000008	/* TX DMA full Stop [5210] */
+#define AR5K_TXCFG_TXFULL		0x000003f0	/* TX Triger level mask */
+#define AR5K_TXCFG_TXFULL_S		4
+#define AR5K_TXCFG_TXFULL_0B		0x00000000
+#define AR5K_TXCFG_TXFULL_64B		0x00000010
+#define AR5K_TXCFG_TXFULL_128B		0x00000020
+#define AR5K_TXCFG_TXFULL_192B		0x00000030
+#define AR5K_TXCFG_TXFULL_256B		0x00000040
+#define AR5K_TXCFG_TXCONT_EN		0x00000080
+#define AR5K_TXCFG_DMASIZE		0x00000100	/* Flag for passing DMA size [5210] */
+#define AR5K_TXCFG_JUMBO_DESC_EN	0x00000400	/* Enable jumbo tx descriptors [5211+] */
+#define AR5K_TXCFG_ADHOC_BCN_ATIM	0x00000800	/* Adhoc Beacon ATIM Policy */
+#define AR5K_TXCFG_ATIM_WINDOW_DEF_DIS	0x00001000	/* Disable ATIM window defer [5211+] */
+#define AR5K_TXCFG_RTSRND		0x00001000	/* [5211+] */
+#define AR5K_TXCFG_FRMPAD_DIS		0x00002000	/* [5211+] */
+#define AR5K_TXCFG_RDY_CBR_DIS		0x00004000	/* Ready time CBR disable [5211+] */
+#define AR5K_TXCFG_JUMBO_FRM_MODE	0x00008000	/* Jumbo frame mode [5211+] */
+#define AR5K_TXCFG_DCU_CACHING_DIS	0x00010000	/* Disable DCU caching */
 
 /*
  * Receive configuration register
  */
 #define AR5K_RXCFG		0x0034			/* Register Address */
-#define AR5K_RXCFG_SDMAMW	0x00000007	/* DMA size */
+#define AR5K_RXCFG_SDMAMW	0x00000007	/* DMA size (write) */
 #define AR5K_RXCFG_SDMAMW_S	0
-#define	AR5K_RXCFG_DEF_ANTENNA	0x00000008	/* Default antenna */
-#define AR5K_RXCFG_ZLFDMA	0x00000010	/* Zero-length DMA */
-#define AR5K_RXCFG_JUMBO_RXE	0x00000020	/* Enable jumbo frames reception (?) [5211+] */
-#define AR5K_RXCFG_JUMBO_WRAP	0x00000040	/* Wrap jumbo frames (?) [5211+] */
+#define AR5K_RXCFG_ZLFDMA	0x00000008	/* Enable Zero-length frame DMA */
+#define	AR5K_RXCFG_DEF_ANTENNA	0x00000010	/* Default antenna (?) */
+#define AR5K_RXCFG_JUMBO_RXE	0x00000020	/* Enable jumbo rx descriptors [5211+] */
+#define AR5K_RXCFG_JUMBO_WRAP	0x00000040	/* Wrap jumbo frames [5211+] */
+#define AR5K_RXCFG_SLE_ENTRY	0x00000080	/* Sleep entry policy */
 
 /*
  * Receive jumbo descriptor last address register
@@ -202,35 +207,35 @@
  * MIB control register
  */
 #define AR5K_MIBC		0x0040			/* Register Address */
-#define AR5K_MIBC_COW		0x00000001
-#define AR5K_MIBC_FMC		0x00000002	/* Freeze Mib Counters (?) */
-#define AR5K_MIBC_CMC		0x00000004	/* Clean Mib Counters (?) */
-#define AR5K_MIBC_MCS		0x00000008
+#define AR5K_MIBC_COW		0x00000001	/* Warn test indicator */
+#define AR5K_MIBC_FMC		0x00000002	/* Freeze MIB Counters  */
+#define AR5K_MIBC_CMC		0x00000004	/* Clean MIB Counters  */
+#define AR5K_MIBC_MCS		0x00000008	/* MIB counter strobe */
 
 /*
  * Timeout prescale register
  */
 #define AR5K_TOPS		0x0044
-#define	AR5K_TOPS_M		0x0000ffff	/* [5211+] (?) */
+#define	AR5K_TOPS_M		0x0000ffff
 
 /*
  * Receive timeout register (no frame received)
  */
 #define AR5K_RXNOFRM		0x0048
-#define	AR5K_RXNOFRM_M		0x000003ff	/* [5211+] (?) */
+#define	AR5K_RXNOFRM_M		0x000003ff
 
 /*
  * Transmit timeout register (no frame sent)
  */
 #define AR5K_TXNOFRM		0x004c
-#define	AR5K_TXNOFRM_M		0x000003ff	/* [5211+] (?) */
-#define	AR5K_TXNOFRM_QCU	0x000ffc00	/* [5211+] (?) */
+#define	AR5K_TXNOFRM_M		0x000003ff
+#define	AR5K_TXNOFRM_QCU	0x000ffc00
 
 /*
  * Receive frame gap timeout register
  */
 #define AR5K_RPGTO		0x0050
-#define AR5K_RPGTO_M		0x000003ff	/* [5211+] (?) */
+#define AR5K_RPGTO_M		0x000003ff
 
 /*
  * Receive frame count limit register
@@ -241,6 +246,7 @@
 
 /*
  * Misc settings register
+ * (reserved0-3)
  */
 #define AR5K_MISC		0x0058			/* Register Address */
 #define	AR5K_MISC_DMA_OBS_M	0x000001e0
@@ -256,6 +262,7 @@
 
 /*
  * QCU/DCU clock gating register (5311)
+ * (reserved4-5)
  */
 #define	AR5K_QCUDCU_CLKGT	0x005c			/* Register Address (?) */
 #define	AR5K_QCUDCU_CLKGT_QCU	0x0000ffff	/* Mask for QCU clock */
@@ -284,18 +291,18 @@
 #define AR5K_ISR_TXEOL		0x00000400	/* Empty TX descriptor */
 #define AR5K_ISR_TXURN		0x00000800	/* Transmit FIFO underrun */
 #define AR5K_ISR_MIB		0x00001000	/* Update MIB counters */
-#define AR5K_ISR_SWI		0x00002000	/* Software interrupt (?) */
+#define AR5K_ISR_SWI		0x00002000	/* Software interrupt */
 #define AR5K_ISR_RXPHY		0x00004000	/* PHY error */
-#define AR5K_ISR_RXKCM		0x00008000
+#define AR5K_ISR_RXKCM		0x00008000	/* RX Key cache miss */
 #define AR5K_ISR_SWBA		0x00010000	/* Software beacon alert */
 #define AR5K_ISR_BRSSI		0x00020000
 #define AR5K_ISR_BMISS		0x00040000	/* Beacon missed */
 #define AR5K_ISR_HIUERR		0x00080000	/* Host Interface Unit error [5211+] */
 #define AR5K_ISR_BNR		0x00100000 	/* Beacon not ready [5211+] */
-#define AR5K_ISR_MCABT		0x00100000	/* [5210] */
-#define AR5K_ISR_RXCHIRP	0x00200000	/* [5212+] */
-#define AR5K_ISR_SSERR		0x00200000	/* [5210] */
-#define AR5K_ISR_DPERR		0x00400000	/* [5210] */
+#define AR5K_ISR_MCABT		0x00100000	/* Master Cycle Abort [5210] */
+#define AR5K_ISR_RXCHIRP	0x00200000	/* CHIRP Received [5212+] */
+#define AR5K_ISR_SSERR		0x00200000	/* Signaled System Error [5210] */
+#define AR5K_ISR_DPERR		0x00400000	/* Det par Error (?) [5210] */
 #define AR5K_ISR_TIM		0x00800000	/* [5210] */
 #define AR5K_ISR_BCNMISC	0x00800000	/* [5212+] */
 #define AR5K_ISR_GPIO		0x01000000	/* GPIO (rf kill)*/
@@ -320,14 +327,14 @@
 
 #define AR5K_SISR2		0x008c			/* Register Address [5211+] */
 #define AR5K_SISR2_QCU_TXURN	0x000003ff	/* Mask for QCU_TXURN */
-#define	AR5K_SISR2_MCABT	0x00100000
-#define	AR5K_SISR2_SSERR	0x00200000
-#define	AR5K_SISR2_DPERR	0x00400000
+#define	AR5K_SISR2_MCABT	0x00100000	/* Master Cycle Abort */
+#define	AR5K_SISR2_SSERR	0x00200000	/* Signaled System Error */
+#define	AR5K_SISR2_DPERR	0x00400000	/* Det par Error (?) */
 #define	AR5K_SISR2_TIM		0x01000000	/* [5212+] */
 #define	AR5K_SISR2_CAB_END	0x02000000	/* [5212+] */
-#define	AR5K_SISR2_DTIM_SYNC	0x04000000	/* [5212+] */
-#define	AR5K_SISR2_BCN_TIMEOUT	0x08000000	/* [5212+] */
-#define	AR5K_SISR2_CAB_TIMEOUT	0x10000000	/* [5212+] */
+#define	AR5K_SISR2_DTIM_SYNC	0x04000000	/* DTIM sync lost [5212+] */
+#define	AR5K_SISR2_BCN_TIMEOUT	0x08000000	/* Beacon Timeout [5212+] */
+#define	AR5K_SISR2_CAB_TIMEOUT	0x10000000	/* CAB Timeout [5212+] */
 #define	AR5K_SISR2_DTIM		0x20000000	/* [5212+] */
 
 #define AR5K_SISR3		0x0090			/* Register Address [5211+] */
@@ -368,18 +375,18 @@
 #define AR5K_IMR_TXEOL		0x00000400	/* Empty TX descriptor*/
 #define AR5K_IMR_TXURN		0x00000800	/* Transmit FIFO underrun*/
 #define AR5K_IMR_MIB		0x00001000	/* Update MIB counters*/
-#define AR5K_IMR_SWI		0x00002000
+#define AR5K_IMR_SWI		0x00002000	/* Software interrupt */
 #define AR5K_IMR_RXPHY		0x00004000	/* PHY error*/
-#define AR5K_IMR_RXKCM		0x00008000
+#define AR5K_IMR_RXKCM		0x00008000	/* RX Key cache miss */
 #define AR5K_IMR_SWBA		0x00010000	/* Software beacon alert*/
 #define AR5K_IMR_BRSSI		0x00020000
 #define AR5K_IMR_BMISS		0x00040000	/* Beacon missed*/
 #define AR5K_IMR_HIUERR		0x00080000	/* Host Interface Unit error [5211+] */
 #define AR5K_IMR_BNR		0x00100000 	/* Beacon not ready [5211+] */
-#define AR5K_IMR_MCABT		0x00100000	/* [5210] */
-#define AR5K_IMR_RXCHIRP	0x00200000	/* [5212+]*/
-#define AR5K_IMR_SSERR		0x00200000	/* [5210] */
-#define AR5K_IMR_DPERR		0x00400000	/* [5210] */
+#define AR5K_IMR_MCABT		0x00100000	/* Master Cycle Abort [5210] */
+#define AR5K_IMR_RXCHIRP	0x00200000	/* CHIRP Received [5212+]*/
+#define AR5K_IMR_SSERR		0x00200000	/* Signaled System Error [5210] */
+#define AR5K_IMR_DPERR		0x00400000	/* Det par Error (?) [5210] */
 #define AR5K_IMR_TIM		0x00800000	/* [5211+] */
 #define AR5K_IMR_BCNMISC	0x00800000	/* [5212+] */
 #define AR5K_IMR_GPIO		0x01000000	/* GPIO (rf kill)*/
@@ -405,14 +412,14 @@
 #define AR5K_SIMR2		0x00ac			/* Register Address [5211+] */
 #define AR5K_SIMR2_QCU_TXURN	0x000003ff	/* Mask for QCU_TXURN */
 #define AR5K_SIMR2_QCU_TXURN_S	0
-#define	AR5K_SIMR2_MCABT	0x00100000
-#define	AR5K_SIMR2_SSERR	0x00200000
-#define	AR5K_SIMR2_DPERR	0x00400000
+#define	AR5K_SIMR2_MCABT	0x00100000	/* Master Cycle Abort */
+#define	AR5K_SIMR2_SSERR	0x00200000	/* Signaled System Error */
+#define	AR5K_SIMR2_DPERR	0x00400000	/* Det par Error (?) */
 #define	AR5K_SIMR2_TIM		0x01000000	/* [5212+] */
 #define	AR5K_SIMR2_CAB_END	0x02000000	/* [5212+] */
-#define	AR5K_SIMR2_DTIM_SYNC	0x04000000	/* [5212+] */
-#define	AR5K_SIMR2_BCN_TIMEOUT	0x08000000	/* [5212+] */
-#define	AR5K_SIMR2_CAB_TIMEOUT	0x10000000	/* [5212+] */
+#define	AR5K_SIMR2_DTIM_SYNC	0x04000000	/* DTIM Sync lost [5212+] */
+#define	AR5K_SIMR2_BCN_TIMEOUT	0x08000000	/* Beacon Timeout [5212+] */
+#define	AR5K_SIMR2_CAB_TIMEOUT	0x10000000	/* CAB Timeout [5212+] */
 #define	AR5K_SIMR2_DTIM		0x20000000	/* [5212+] */
 
 #define AR5K_SIMR3		0x00b0			/* Register Address [5211+] */
@@ -425,23 +432,69 @@
 #define AR5K_SIMR4_QTRIG	0x000003ff	/* Mask for QTRIG */
 #define AR5K_SIMR4_QTRIG_S	0
 
+/*
+ * DMA Debug registers 0-7
+ * 0xe0 - 0xfc
+ */
 
 /*
  * Decompression mask registers [5212+]
  */
-#define AR5K_DCM_ADDR		0x0400		/*Decompression mask address (?)*/
-#define AR5K_DCM_DATA		0x0404		/*Decompression mask data (?)*/
+#define AR5K_DCM_ADDR		0x0400		/*Decompression mask address (index) */
+#define AR5K_DCM_DATA		0x0404		/*Decompression mask data */
+
+/*
+ * Wake On Wireless pattern control register [5212+]
+ */
+#define	AR5K_WOW_PCFG			0x0410			/* Register Address */
+#define	AR5K_WOW_PCFG_PAT_MATCH_EN	0x00000001	/* Pattern match enable */
+#define	AR5K_WOW_PCFG_LONG_FRAME_POL	0x00000002	/* Long frame policy */
+#define	AR5K_WOW_PCFG_WOBMISS		0x00000004	/* Wake on bea(con) miss (?) */
+#define	AR5K_WOW_PCFG_PAT_0_EN		0x00000100	/* Enable pattern 0 */
+#define	AR5K_WOW_PCFG_PAT_1_EN		0x00000200	/* Enable pattern 1 */
+#define	AR5K_WOW_PCFG_PAT_2_EN		0x00000400	/* Enable pattern 2 */
+#define	AR5K_WOW_PCFG_PAT_3_EN		0x00000800	/* Enable pattern 3 */
+#define	AR5K_WOW_PCFG_PAT_4_EN		0x00001000	/* Enable pattern 4 */
+#define	AR5K_WOW_PCFG_PAT_5_EN		0x00002000	/* Enable pattern 5 */
+
+/*
+ * Wake On Wireless pattern index register (?) [5212+]
+ */
+#define	AR5K_WOW_PAT_IDX	0x0414
+
+/*
+ * Wake On Wireless pattern data register [5212+]
+ */
+#define	AR5K_WOW_PAT_DATA	0x0418			/* Register Address */
+#define	AR5K_WOW_PAT_DATA_0_3_V	0x00000001	/* Pattern 0, 3 value */
+#define	AR5K_WOW_PAT_DATA_1_4_V	0x00000100	/* Pattern 1, 4 value */
+#define	AR5K_WOW_PAT_DATA_2_5_V	0x00010000	/* Pattern 2, 5 value */
+#define	AR5K_WOW_PAT_DATA_0_3_M	0x01000000	/* Pattern 0, 3 mask */
+#define	AR5K_WOW_PAT_DATA_1_4_M	0x04000000	/* Pattern 1, 4 mask */
+#define	AR5K_WOW_PAT_DATA_2_5_M	0x10000000	/* Pattern 2, 5 mask */
 
 /*
  * Decompression configuration registers [5212+]
  */
-#define AR5K_DCCFG		0x0420
+#define AR5K_DCCFG		0x0420			/* Register Address */
+#define AR5K_DCCFG_GLOBAL_EN	0x00000001	/* Enable decompression on all queues */
+#define AR5K_DCCFG_BYPASS_EN	0x00000002	/* Bypass decompression */
+#define AR5K_DCCFG_BCAST_EN	0x00000004	/* Enable decompression for bcast frames */
+#define AR5K_DCCFG_MCAST_EN	0x00000008	/* Enable decompression for mcast frames */
 
 /*
  * Compression configuration registers [5212+]
  */
-#define AR5K_CCFG		0x0600
-#define AR5K_CCFG_CUP		0x0604
+#define AR5K_CCFG		0x0600			/* Register Address */
+#define	AR5K_CCFG_WINDOW_SIZE	0x00000007	/* Compression window size */
+#define	AR5K_CCFG_CPC_EN	0x00000008	/* Enable performance counters */
+
+#define AR5K_CCFG_CCU		0x0604			/* Register Address */
+#define AR5K_CCFG_CCU_CUP_EN	0x00000001	/* CCU Catchup enable */
+#define AR5K_CCFG_CCU_CREDIT	0x00000002	/* CCU Credit (field) */
+#define AR5K_CCFG_CCU_CD_THRES	0x00000080	/* CCU Cyc(lic?) debt threshold (field) */
+#define AR5K_CCFG_CCU_CUP_LCNT	0x00010000	/* CCU Catchup lit(?) count */
+#define	AR5K_CCFG_CCU_INIT	0x00100200	/* Initial value during reset */
 
 /*
  * Compression performance counter registers [5212+]
@@ -450,7 +503,7 @@
 #define AR5K_CPC1		0x0614		/* Compression performance counter 1*/
 #define AR5K_CPC2		0x0618		/* Compression performance counter 2 */
 #define AR5K_CPC3		0x061c		/* Compression performance counter 3 */
-#define AR5K_CPCORN		0x0620		/* Compression performance overrun (?) */
+#define AR5K_CPCOVF		0x0620		/* Compression performance overflow */
 
 
 /*
@@ -466,8 +519,6 @@
  * set/clear, which contain status for all queues (we shift by 1 for each
  * queue). To access these registers easily we define some macros here
  * that are used inside HAL. For more infos check out *_tx_queue functs.
- *
- * TODO: Boundary checking on macros (here?)
  */
 
 /*
@@ -513,7 +564,6 @@
 #define	AR5K_QCU_RDYTIMECFG_BASE	0x0900	/* Register Address - Queue0 RDYTIMECFG */
 #define	AR5K_QCU_RDYTIMECFG_INTVAL	0x00ffffff	/* Ready time interval mask */
 #define AR5K_QCU_RDYTIMECFG_INTVAL_S	0
-#define	AR5K_QCU_RDYTIMECFG_DURATION	0x00ffffff	/* Ready time duration mask */
 #define	AR5K_QCU_RDYTIMECFG_ENABLE	0x01000000	/* Ready time enable mask */
 #define AR5K_QUEUE_RDYTIMECFG(_q)	AR5K_QUEUE_REG(AR5K_QCU_RDYTIMECFG_BASE, _q)
 
@@ -534,19 +584,20 @@
  */
 #define AR5K_QCU_MISC_BASE		0x09c0			/* Register Address -Queue0 MISC */
 #define	AR5K_QCU_MISC_FRSHED_M		0x0000000f	/* Frame sheduling mask */
-#define	AR5K_QCU_MISC_FRSHED_ASAP	0		/* ASAP */
-#define	AR5K_QCU_MISC_FRSHED_CBR	1		/* Constant Bit Rate */
-#define	AR5K_QCU_MISC_FRSHED_DBA_GT	2		/* DMA Beacon alert gated (?) */
-#define	AR5K_QCU_MISC_FRSHED_TIM_GT	3		/* Time gated (?) */
+#define	AR5K_QCU_MISC_FRSHED_ASAP		0	/* ASAP */
+#define	AR5K_QCU_MISC_FRSHED_CBR		1	/* Constant Bit Rate */
+#define	AR5K_QCU_MISC_FRSHED_DBA_GT		2	/* DMA Beacon alert gated (?) */
+#define	AR5K_QCU_MISC_FRSHED_TIM_GT		3	/* Time gated (?) */
 #define	AR5K_QCU_MISC_FRSHED_BCN_SENT_GT	4	/* Beacon sent gated (?) */
 #define	AR5K_QCU_MISC_ONESHOT_ENABLE	0x00000010	/* Oneshot enable */
 #define	AR5K_QCU_MISC_CBREXP		0x00000020	/* CBR expired (normal queue) */
 #define	AR5K_QCU_MISC_CBREXP_BCN	0x00000040	/* CBR expired (beacon queue) */
-#define	AR5K_QCU_MISC_BCN_ENABLE	0x00000080	/* Beacons enabled */
-#define	AR5K_QCU_MISC_CBR_THRES_ENABLE	0x00000100	/* CBR threshold enabled (?) */
-#define	AR5K_QCU_MISC_TXE		0x00000200	/* TXE reset when RDYTIME enalbed (?) */
-#define	AR5K_QCU_MISC_CBR		0x00000400	/* CBR threshold reset (?) */
-#define	AR5K_QCU_MISC_DCU_EARLY		0x00000800	/* DCU reset (?) */
+#define	AR5K_QCU_MISC_BCN_ENABLE	0x00000080	/* Enable Beacon use */
+#define	AR5K_QCU_MISC_CBR_THRES_ENABLE	0x00000100	/* CBR threshold enabled */
+#define	AR5K_QCU_MISC_RDY_VEOL_POLICY	0x00000200	/* TXE reset when RDYTIME enalbed */
+#define	AR5K_QCU_MISC_CBR_RESET_CNT	0x00000400	/* CBR threshold (counter) reset */
+#define	AR5K_QCU_MISC_DCU_EARLY		0x00000800	/* DCU early termination */
+#define AR5K_QCU_MISC_DCU_CMP_EN	0x00001000	/* Enable frame compression */
 #define AR5K_QUEUE_MISC(_q)		AR5K_QUEUE_REG(AR5K_QCU_MISC_BASE, _q)
 
 
@@ -555,7 +606,7 @@
  */
 #define AR5K_QCU_STS_BASE	0x0a00			/* Register Address - Queue0 STS */
 #define	AR5K_QCU_STS_FRMPENDCNT	0x00000003	/* Frames pending counter */
-#define	AR5K_QCU_STS_CBREXPCNT	0x0000ff00	/* CBR expired counter (?) */
+#define	AR5K_QCU_STS_CBREXPCNT	0x0000ff00	/* CBR expired counter */
 #define	AR5K_QUEUE_STATUS(_q)	AR5K_QUEUE_REG(AR5K_QCU_STS_BASE, _q)
 
 /*
@@ -569,9 +620,11 @@
  */
 #define AR5K_QCU_CBB_SELECT	0x0b00
 #define AR5K_QCU_CBB_ADDR	0x0b04
+#define AR5K_QCU_CBB_ADDR_S	9
 
 /*
  * QCU compression buffer configuration register [5212+]
+ * (buffer size)
  */
 #define AR5K_QCU_CBCFG		0x0b08
 
@@ -652,80 +705,100 @@
  * No lockout means there is no special handling.
  */
 #define AR5K_DCU_MISC_BASE		0x1100			/* Register Address -Queue0 DCU_MISC */
-#define	AR5K_DCU_MISC_BACKOFF		0x000007ff	/* Mask for backoff setting (?) */
+#define	AR5K_DCU_MISC_BACKOFF		0x000007ff	/* Mask for backoff threshold */
 #define AR5K_DCU_MISC_BACKOFF_FRAG	0x00000200	/* Enable backoff while bursting */
-#define	AR5K_DCU_MISC_HCFPOLL_ENABLE	0x00000800	/* CF - Poll (?) */
-#define	AR5K_DCU_MISC_BACKOFF_PERSIST	0x00001000	/* Persistent backoff (?) */
-#define	AR5K_DCU_MISC_FRMPRFTCH_ENABLE	0x00002000	/* Enable frame pre-fetch (?) */
+#define	AR5K_DCU_MISC_HCFPOLL_ENABLE	0x00000800	/* CF - Poll enable */
+#define	AR5K_DCU_MISC_BACKOFF_PERSIST	0x00001000	/* Persistent backoff */
+#define	AR5K_DCU_MISC_FRMPRFTCH_ENABLE	0x00002000	/* Enable frame pre-fetch */
 #define	AR5K_DCU_MISC_VIRTCOL		0x0000c000	/* Mask for Virtual Collision (?) */
-#define	AR5K_DCU_MISC_VIRTCOL_NORMAL	0
-#define	AR5K_DCU_MISC_VIRTCOL_MODIFIED	1
-#define	AR5K_DCU_MISC_VIRTCOL_IGNORE	2
-#define	AR5K_DCU_MISC_BCN_ENABLE	0x00010000	/* Beacon enable (?) */
+#define	AR5K_DCU_MISC_VIRTCOL_NORMAL		0
+#define	AR5K_DCU_MISC_VIRTCOL_MODIFIED		1
+#define	AR5K_DCU_MISC_VIRTCOL_IGNORE		2
+#define	AR5K_DCU_MISC_BCN_ENABLE	0x00010000	/* Enable Beacon use */
 #define	AR5K_DCU_MISC_ARBLOCK_CTL	0x00060000	/* Arbiter lockout control mask */
 #define	AR5K_DCU_MISC_ARBLOCK_CTL_S	17
-#define	AR5K_DCU_MISC_ARBLOCK_CTL_NONE	0		/* No arbiter lockout */
+#define	AR5K_DCU_MISC_ARBLOCK_CTL_NONE		0	/* No arbiter lockout */
 #define	AR5K_DCU_MISC_ARBLOCK_CTL_INTFRM	1	/* Intra-frame lockout */
 #define	AR5K_DCU_MISC_ARBLOCK_CTL_GLOBAL	2	/* Global lockout */
-#define	AR5K_DCU_MISC_ARBLOCK_IGNORE	0x00080000
-#define	AR5K_DCU_MISC_SEQ_NUM_INCR_DIS	0x00100000	/* Disable sequence number increment (?) */
-#define	AR5K_DCU_MISC_POST_FR_BKOFF_DIS	0x00200000	/* Disable post-frame backoff (?) */
-#define	AR5K_DCU_MISC_VIRT_COLL_POLICY	0x00400000	/* Virtual Collision policy (?) */
-#define	AR5K_DCU_MISC_BLOWN_IFS_POLICY	0x00800000
+#define	AR5K_DCU_MISC_ARBLOCK_IGNORE	0x00080000	/* Ignore Arbiter lockout */
+#define	AR5K_DCU_MISC_SEQ_NUM_INCR_DIS	0x00100000	/* Disable sequence number increment */
+#define	AR5K_DCU_MISC_POST_FR_BKOFF_DIS	0x00200000	/* Disable post-frame backoff */
+#define	AR5K_DCU_MISC_VIRT_COLL_POLICY	0x00400000	/* Virtual Collision cw policy */
+#define	AR5K_DCU_MISC_BLOWN_IFS_POLICY	0x00800000	/* Blown IFS policy (?) */
 #define	AR5K_DCU_MISC_SEQNUM_CTL	0x01000000	/* Sequence number control (?) */
 #define AR5K_QUEUE_DFS_MISC(_q)		AR5K_QUEUE_REG(AR5K_DCU_MISC_BASE, _q)
 
 /*
  * DCU frame sequence number registers
  */
-#define AR5K_DCU_SEQNUM_BASE	0x1140
-#define	AR5K_DCU_SEQNUM_M	0x00000fff
+#define AR5K_DCU_SEQNUM_BASE		0x1140
+#define	AR5K_DCU_SEQNUM_M		0x00000fff
 #define	AR5K_QUEUE_DFS_SEQNUM(_q)	AR5K_QUEUE_REG(AR5K_DCU_SEQNUM_BASE, _q)
 
 /*
- * DCU global IFS SIFS registers
+ * DCU global IFS SIFS register
  */
 #define AR5K_DCU_GBL_IFS_SIFS	0x1030
 #define AR5K_DCU_GBL_IFS_SIFS_M	0x0000ffff
 
 /*
- * DCU global IFS slot interval registers
+ * DCU global IFS slot interval register
  */
 #define AR5K_DCU_GBL_IFS_SLOT	0x1070
 #define AR5K_DCU_GBL_IFS_SLOT_M	0x0000ffff
 
 /*
- * DCU global IFS EIFS registers
+ * DCU global IFS EIFS register
  */
 #define AR5K_DCU_GBL_IFS_EIFS	0x10b0
 #define AR5K_DCU_GBL_IFS_EIFS_M	0x0000ffff
 
 /*
- * DCU global IFS misc registers
+ * DCU global IFS misc register
+ *
+ * LFSR stands for Linear Feedback Shift Register
+ * and it's used for generating pseudo-random
+ * number sequences.
+ *
+ * (If i understand corectly, random numbers are
+ * used for idle sensing -multiplied with cwmin/max etc-)
  */
 #define AR5K_DCU_GBL_IFS_MISC			0x10f0			/* Register Address */
-#define	AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE	0x00000007
-#define	AR5K_DCU_GBL_IFS_MISC_TURBO_MODE	0x00000008	/* Turbo mode (?) */
-#define	AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC	0x000003f0	/* SIFS Duration mask (?) */
-#define	AR5K_DCU_GBL_IFS_MISC_USEC_DUR		0x000ffc00
-#define	AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY	0x00300000
+#define	AR5K_DCU_GBL_IFS_MISC_LFSR_SLICE	0x00000007	/* LFSR Slice Select */
+#define	AR5K_DCU_GBL_IFS_MISC_TURBO_MODE	0x00000008	/* Turbo mode */
+#define	AR5K_DCU_GBL_IFS_MISC_SIFS_DUR_USEC	0x000003f0	/* SIFS Duration mask */
+#define	AR5K_DCU_GBL_IFS_MISC_USEC_DUR		0x000ffc00	/* USEC Duration mask */
+#define	AR5K_DCU_GBL_IFS_MISC_DCU_ARB_DELAY	0x00300000	/* DCU Arbiter delay mask */
+#define AR5K_DCU_GBL_IFS_MISC_SIFS_CNT_RST	0x00400000	/* SIFC cnt reset policy (?) */
+#define AR5K_DCU_GBL_IFS_MISC_AIFS_CNT_RST	0x00800000	/* AIFS cnt reset policy (?) */
+#define AR5K_DCU_GBL_IFS_MISC_RND_LFSR_SL_DIS	0x01000000	/* Disable random LFSR slice */
 
 /*
  * DCU frame prefetch control register
  */
-#define AR5K_DCU_FP		0x1230
+#define AR5K_DCU_FP			0x1230			/* Register Address */
+#define AR5K_DCU_FP_NOBURST_DCU_EN	0x00000001	/* Enable non-burst prefetch on DCU (?) */
+#define AR5K_DCU_FP_NOBURST_EN		0x00000010	/* Enable non-burst prefetch (?) */
+#define AR5K_DCU_FP_BURST_DCU_EN	0x00000020	/* Enable burst prefetch on DCU (?) */
 
 /*
  * DCU transmit pause control/status register
  */
 #define AR5K_DCU_TXP		0x1270			/* Register Address */
-#define	AR5K_DCU_TXP_M		0x000003ff	/* Tx pause mask (?) */
-#define	AR5K_DCU_TXP_STATUS	0x00010000	/* Tx pause status (?) */
+#define	AR5K_DCU_TXP_M		0x000003ff	/* Tx pause mask */
+#define	AR5K_DCU_TXP_STATUS	0x00010000	/* Tx pause status */
+
+/*
+ * DCU transmit filter table 0 (32 entries)
+ */
+#define AR5K_DCU_TX_FILTER_0_BASE	0x1038
+#define	AR5K_DCU_TX_FILTER_0(_n)	(AR5K_DCU_TX_FILTER_0_BASE + (_n * 64))
 
 /*
- * DCU transmit filter register
+ * DCU transmit filter table 1 (16 entries)
  */
-#define AR5K_DCU_TX_FILTER	0x1038
+#define AR5K_DCU_TX_FILTER_1_BASE	0x103c
+#define	AR5K_DCU_TX_FILTER_1(_n)	(AR5K_DCU_TX_FILTER_1_BASE + ((_n - 32) * 64))
 
 /*
  * DCU clear transmit filter register
@@ -739,9 +812,6 @@
 
 /*
  * Reset control register
- *
- * 4 and 8 are not used in 5211/5212 and
- * 2 means "baseband reset" on 5211/5212.
  */
 #define AR5K_RESET_CTL		0x4000			/* Register Address */
 #define AR5K_RESET_CTL_PCU	0x00000001	/* Protocol Control Unit reset */
@@ -765,6 +835,7 @@
 #define AR5K_SLEEP_CTL_SLE_SLP		0x00010000	/* Force chip sleep */
 #define AR5K_SLEEP_CTL_SLE_ALLOW	0x00020000
 #define AR5K_SLEEP_CTL_SLE_UNITS	0x00000008	/* [5211+] */
+/* more bits */
 
 /*
  * Interrupt pending register
@@ -776,13 +847,14 @@
  * Sleep force register
  */
 #define AR5K_SFR	0x400c
-#define AR5K_SFR_M	0x00000001
+#define AR5K_SFR_EN	0x00000001
 
 /*
  * PCI configuration register
  */
 #define AR5K_PCICFG			0x4010			/* Register Address */
 #define AR5K_PCICFG_EEAE		0x00000001	/* Eeprom access enable [5210] */
+#define	AR5K_PCICFG_SLEEP_CLOCK_EN	0x00000002	/* Enable sleep clock (?) */
 #define AR5K_PCICFG_CLKRUNEN		0x00000004	/* CLKRUN enable [5211+] */
 #define AR5K_PCICFG_EESIZE		0x00000018	/* Mask for EEPROM size [5211+] */
 #define AR5K_PCICFG_EESIZE_S		3
@@ -798,19 +870,21 @@
 #define	AR5K_PCICFG_CBEFIX_DIS		0x00000400	/* Disable CBE fix (?) */
 #define AR5K_PCICFG_SL_INTEN		0x00000800	/* Enable interrupts when asleep (?) */
 #define AR5K_PCICFG_LED_BCTL		0x00001000	/* Led blink (?) [5210] */
-#define AR5K_PCICFG_SL_INPEN		0x00002800	/* Sleep even whith pending interrupts (?) */
+#define	AR5K_PCICFG_UNK			0x00001000	/* Passed on some parts durring attach (?) */
+#define AR5K_PCICFG_SL_INPEN		0x00002000	/* Sleep even whith pending interrupts (?) */
 #define AR5K_PCICFG_SPWR_DN		0x00010000	/* Mask for power status */
 #define AR5K_PCICFG_LEDMODE		0x000e0000	/* Ledmode [5211+] */
 #define AR5K_PCICFG_LEDMODE_PROP	0x00000000	/* Blink on standard traffic [5211+] */
 #define AR5K_PCICFG_LEDMODE_PROM	0x00020000	/* Default mode (blink on any traffic) [5211+] */
 #define AR5K_PCICFG_LEDMODE_PWR		0x00040000	/* Some other blinking mode  (?) [5211+] */
 #define AR5K_PCICFG_LEDMODE_RAND	0x00060000	/* Random blinking (?) [5211+] */
-#define AR5K_PCICFG_LEDBLINK		0x00700000
+#define AR5K_PCICFG_LEDBLINK		0x00700000	/* Led blink rate */
 #define AR5K_PCICFG_LEDBLINK_S		20
-#define AR5K_PCICFG_LEDSLOW		0x00800000	/* Slow led blink rate (?) [5211+] */
+#define AR5K_PCICFG_LEDSLOW		0x00800000	/* Slowest led blink rate [5211+] */
 #define AR5K_PCICFG_LEDSTATE				\
 	(AR5K_PCICFG_LED | AR5K_PCICFG_LEDMODE |	\
 	AR5K_PCICFG_LEDBLINK | AR5K_PCICFG_LEDSLOW)
+#define	AR5K_PCICFG_SLEEP_CLOCK_RATE	0x03000000	/* Sleep clock rate (field) */
 
 /*
  * "General Purpose Input/Output" (GPIO) control register
@@ -947,7 +1021,7 @@
 #define AR5K_EEPROM_VERSION_4_4		0x4004
 #define AR5K_EEPROM_VERSION_4_5		0x4005
 #define AR5K_EEPROM_VERSION_4_6		0x4006	/* has ee_scaled_cck_delta */
-#define AR5K_EEPROM_VERSION_4_7		0x3007
+#define AR5K_EEPROM_VERSION_4_7		0x4007
 
 #define AR5K_EEPROM_MODE_11A		0
 #define AR5K_EEPROM_MODE_11B		1
@@ -1023,10 +1097,14 @@
 #define AR5K_EEPROM_STAT_WRDONE	0x00000008	/* EEPROM write successful */
 
 /*
- * EEPROM config register (?)
+ * EEPROM config register
  */
-#define AR5K_EEPROM_CFG	0x6010
-
+#define AR5K_EEPROM_CFG			0x6010			/* Register Addres */
+#define AR5K_EEPROM_CFG_SIZE_OVR	0x00000001
+#define AR5K_EEPROM_CFG_WR_WAIT_DIS	0x00000004	/* Disable write wait */
+#define AR5K_EEPROM_CFG_CLK_RATE	0x00000018	/* Clock rate */
+#define AR5K_EEPROM_CFG_PROT_KEY	0x00ffff00	/* Protectio key */
+#define AR5K_EEPROM_CFG_LIND_EN		0x01000000	/* Enable length indicator (?) */
 
 
 /*
@@ -1050,7 +1128,7 @@
 #define AR5K_STA_ID1			0x8004			/* Register Address */
 #define AR5K_STA_ID1_AP			0x00010000	/* Set AP mode */
 #define AR5K_STA_ID1_ADHOC		0x00020000	/* Set Ad-Hoc mode */
-#define AR5K_STA_ID1_PWR_SV		0x00040000	/* Power save reporting (?) */
+#define AR5K_STA_ID1_PWR_SV		0x00040000	/* Power save reporting */
 #define AR5K_STA_ID1_NO_KEYSRCH		0x00080000	/* No key search */
 #define AR5K_STA_ID1_NO_PSPOLL		0x00100000	/* No power save polling [5210] */
 #define AR5K_STA_ID1_PCF_5211		0x00100000	/* Enable PCF on [5211+] */
@@ -1059,9 +1137,13 @@
 					AR5K_STA_ID1_PCF_5210 : AR5K_STA_ID1_PCF_5211)
 #define AR5K_STA_ID1_DEFAULT_ANTENNA	0x00200000	/* Use default antenna */
 #define AR5K_STA_ID1_DESC_ANTENNA	0x00400000	/* Update antenna from descriptor */
-#define AR5K_STA_ID1_RTS_DEF_ANTENNA	0x00800000	/* Use default antenna for RTS (?) */
-#define AR5K_STA_ID1_ACKCTS_6MB		0x01000000	/* Use 6Mbit/s for ACK/CTS (?) */
+#define AR5K_STA_ID1_RTS_DEF_ANTENNA	0x00800000	/* Use default antenna for RTS */
+#define AR5K_STA_ID1_ACKCTS_6MB		0x01000000	/* Use 6Mbit/s for ACK/CTS */
 #define AR5K_STA_ID1_BASE_RATE_11B	0x02000000	/* Use 11b base rate (for ACK/CTS ?) [5211+] */
+#define AR5K_STA_ID1_SELF_GEN_SECTORE	0x04000000	/* Self generate sectore (?) */
+#define AR5K_STA_ID1_CRYPT_MIC_EN	0x08000000	/* Enable MIC */
+#define AR5K_STA_ID1_KEYSRCH_MODE	0x10000000	/* Keysearch mode (?) */
+#define AR5K_STA_ID1_PRESERVE_SEQ_NUM	0x20000000	/* Preserve sequence number */
 
 /*
  * First BSSID register (MAC address, lower 32bits)
@@ -1117,7 +1199,7 @@
  *
  * Retry limit register for 5210 (no QCU/DCU so it's done in PCU)
  */
-#define AR5K_NODCU_RETRY_LMT		0x801c			/*Register Address */
+#define AR5K_NODCU_RETRY_LMT		0x801c			/* Register Address */
 #define AR5K_NODCU_RETRY_LMT_SH_RETRY	0x0000000f	/* Short retry limit mask */
 #define AR5K_NODCU_RETRY_LMT_SH_RETRY_S	0
 #define AR5K_NODCU_RETRY_LMT_LG_RETRY	0x000000f0	/* Long retry mask */
@@ -1136,9 +1218,9 @@
 #define AR5K_USEC_5211			0x801c			/* Register Address [5211+] */
 #define AR5K_USEC			(ah->ah_version == AR5K_AR5210 ? \
 					AR5K_USEC_5210 : AR5K_USEC_5211)
-#define AR5K_USEC_1			0x0000007f
+#define AR5K_USEC_1			0x0000007f	/* clock cycles for 1us */
 #define AR5K_USEC_1_S			0
-#define AR5K_USEC_32			0x00003f80
+#define AR5K_USEC_32			0x00003f80	/* clock cycles for 1us while on 32Mhz clock */
 #define AR5K_USEC_32_S			7
 #define AR5K_USEC_TX_LATENCY_5211	0x007fc000
 #define AR5K_USEC_TX_LATENCY_5211_S	14
@@ -1152,16 +1234,16 @@
 /*
  * PCU beacon control register
  */
-#define AR5K_BEACON_5210	0x8024
-#define AR5K_BEACON_5211	0x8020
+#define AR5K_BEACON_5210	0x8024			/*Register Address [5210] */
+#define AR5K_BEACON_5211	0x8020			/*Register Address [5211+] */
 #define AR5K_BEACON		(ah->ah_version == AR5K_AR5210 ? \
 				AR5K_BEACON_5210 : AR5K_BEACON_5211)
-#define AR5K_BEACON_PERIOD	0x0000ffff
+#define AR5K_BEACON_PERIOD	0x0000ffff	/* Mask for beacon period */
 #define AR5K_BEACON_PERIOD_S	0
-#define AR5K_BEACON_TIM		0x007f0000
+#define AR5K_BEACON_TIM		0x007f0000	/* Mask for TIM offset */
 #define AR5K_BEACON_TIM_S	16
-#define AR5K_BEACON_ENABLE	0x00800000
-#define AR5K_BEACON_RESET_TSF	0x01000000
+#define AR5K_BEACON_ENABLE	0x00800000	/* Enable beacons */
+#define AR5K_BEACON_RESET_TSF	0x01000000	/* Force TSF reset */
 
 /*
  * CFP period register
@@ -1234,7 +1316,6 @@
 
 /*
  * Receive filter register
- * TODO: Get these out of ar5xxx.h on ath5k
  */
 #define AR5K_RX_FILTER_5210	0x804c			/* Register Address [5210] */
 #define AR5K_RX_FILTER_5211	0x803c			/* Register Address [5211+] */
@@ -1307,11 +1388,11 @@
 #define AR5K_DIAG_SW_5211		0x8048			/* Register Address [5211+] */
 #define AR5K_DIAG_SW			(ah->ah_version == AR5K_AR5210 ? \
 					AR5K_DIAG_SW_5210 : AR5K_DIAG_SW_5211)
-#define AR5K_DIAG_SW_DIS_WEP_ACK	0x00000001
-#define AR5K_DIAG_SW_DIS_ACK		0x00000002	/* Disable ACKs (?) */
-#define AR5K_DIAG_SW_DIS_CTS		0x00000004	/* Disable CTSs (?) */
-#define AR5K_DIAG_SW_DIS_ENC		0x00000008	/* Disable encryption (?) */
-#define AR5K_DIAG_SW_DIS_DEC		0x00000010	/* Disable decryption (?) */
+#define AR5K_DIAG_SW_DIS_WEP_ACK	0x00000001	/* Disable ACKs if WEP key is invalid */
+#define AR5K_DIAG_SW_DIS_ACK		0x00000002	/* Disable ACKs */
+#define AR5K_DIAG_SW_DIS_CTS		0x00000004	/* Disable CTSs */
+#define AR5K_DIAG_SW_DIS_ENC		0x00000008	/* Disable encryption */
+#define AR5K_DIAG_SW_DIS_DEC		0x00000010	/* Disable decryption */
 #define AR5K_DIAG_SW_DIS_TX		0x00000020	/* Disable transmit [5210] */
 #define AR5K_DIAG_SW_DIS_RX_5210	0x00000040	/* Disable recieve */
 #define AR5K_DIAG_SW_DIS_RX_5211	0x00000020
@@ -1329,13 +1410,13 @@
 #define AR5K_DIAG_SW_CHAN_INFO_5211	0x00000100
 #define AR5K_DIAG_SW_CHAN_INFO		(ah->ah_version == AR5K_AR5210 ? \
 					AR5K_DIAG_SW_CHAN_INFO_5210 : AR5K_DIAG_SW_CHAN_INFO_5211)
-#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211	0x00000200	/* Scrambler seed (?) */
+#define AR5K_DIAG_SW_EN_SCRAM_SEED_5211	0x00000200	/* Enable scrambler seed */
 #define AR5K_DIAG_SW_EN_SCRAM_SEED_5210	0x00000400
 #define AR5K_DIAG_SW_EN_SCRAM_SEED	(ah->ah_version == AR5K_AR5210 ? \
 					AR5K_DIAG_SW_EN_SCRAM_SEED_5210 : AR5K_DIAG_SW_EN_SCRAM_SEED_5211)
 #define AR5K_DIAG_SW_ECO_ENABLE		0x00000400	/* [5211+] */
 #define AR5K_DIAG_SW_SCVRAM_SEED	0x0003f800	/* [5210] */
-#define AR5K_DIAG_SW_SCRAM_SEED_M	0x0001fc00	/* Scrambler seed mask (?) */
+#define AR5K_DIAG_SW_SCRAM_SEED_M	0x0001fc00	/* Scrambler seed mask */
 #define AR5K_DIAG_SW_SCRAM_SEED_S	10
 #define AR5K_DIAG_SW_DIS_SEQ_INC	0x00040000	/* Disable seqnum increment (?)[5210] */
 #define AR5K_DIAG_SW_FRAME_NV0_5210	0x00080000
@@ -1344,6 +1425,7 @@
 					AR5K_DIAG_SW_FRAME_NV0_5210 : AR5K_DIAG_SW_FRAME_NV0_5211)
 #define AR5K_DIAG_SW_OBSPT_M		0x000c0000
 #define AR5K_DIAG_SW_OBSPT_S		18
+/* more bits */
 
 /*
  * TSF (clock) register (lower 32 bits)
@@ -1369,15 +1451,34 @@
 /*
  * ADDAC test register [5211+]
  */
-#define AR5K_ADDAC_TEST	0x8054
-#define AR5K_ADDAC_TEST_TXCONT 0x00000001
+#define AR5K_ADDAC_TEST			0x8054			/* Register Address */
+#define AR5K_ADDAC_TEST_TXCONT 		0x00000001	/* Test continuous tx */
+#define AR5K_ADDAC_TEST_TST_MODE	0x00000002	/* Test mode */
+#define AR5K_ADDAC_TEST_LOOP_EN		0x00000004	/* Enable loop */
+#define AR5K_ADDAC_TEST_LOOP_LEN	0x00000008	/* Loop length (field) */
+#define AR5K_ADDAC_TEST_USE_U8		0x00004000	/* Use upper 8 bits */
+#define AR5K_ADDAC_TEST_MSB		0x00008000	/* State of MSB */
+#define AR5K_ADDAC_TEST_TRIG_SEL	0x00010000	/* Trigger select */
+#define AR5K_ADDAC_TEST_TRIG_PTY	0x00020000	/* Trigger polarity */
+#define AR5K_ADDAC_TEST_RXCONT		0x00040000	/* Continuous capture */
+#define AR5K_ADDAC_TEST_CAPTURE		0x00080000	/* Begin capture */
+#define AR5K_ADDAC_TEST_TST_ARM		0x00100000	/* Test ARM (Adaptive Radio Mode ?) */
 
 /*
  * Default antenna register [5211+]
  */
 #define AR5K_DEFAULT_ANTENNA	0x8058
 
+/*
+ * Frame control QoS mask register (?) [5211+]
+ * (FC_QOS_MASK)
+ */
+#define AR5K_FRAME_CTL_QOSM	0x805c
 
+/*
+ * Seq mask register (?) [5211+]
+ */
+#define AR5K_SEQ_MASK	0x8060
 
 /*
  * Retry count register [5210]
@@ -1449,124 +1550,242 @@
 /*
  * XR (eXtended Range) mode register
  */
-#define AR5K_XRMODE			0x80c0
-#define	AR5K_XRMODE_POLL_TYPE_M		0x0000003f
+#define AR5K_XRMODE			0x80c0			/* Register Address */
+#define	AR5K_XRMODE_POLL_TYPE_M		0x0000003f	/* Mask for Poll type (?) */
 #define	AR5K_XRMODE_POLL_TYPE_S		0
-#define	AR5K_XRMODE_POLL_SUBTYPE_M	0x0000003c
+#define	AR5K_XRMODE_POLL_SUBTYPE_M	0x0000003c	/* Mask for Poll subtype (?) */
 #define	AR5K_XRMODE_POLL_SUBTYPE_S	2
-#define	AR5K_XRMODE_POLL_WAIT_ALL	0x00000080
-#define	AR5K_XRMODE_SIFS_DELAY		0x000fff00
-#define	AR5K_XRMODE_FRAME_HOLD_M	0xfff00000
+#define	AR5K_XRMODE_POLL_WAIT_ALL	0x00000080	/* Wait for poll */
+#define	AR5K_XRMODE_SIFS_DELAY		0x000fff00	/* Mask for SIFS delay */
+#define	AR5K_XRMODE_FRAME_HOLD_M	0xfff00000	/* Mask for frame hold (?) */
 #define	AR5K_XRMODE_FRAME_HOLD_S	20
 
 /*
  * XR delay register
  */
-#define AR5K_XRDELAY			0x80c4
-#define AR5K_XRDELAY_SLOT_DELAY_M	0x0000ffff
+#define AR5K_XRDELAY			0x80c4			/* Register Address */
+#define AR5K_XRDELAY_SLOT_DELAY_M	0x0000ffff	/* Mask for slot delay */
 #define AR5K_XRDELAY_SLOT_DELAY_S	0
-#define AR5K_XRDELAY_CHIRP_DELAY_M	0xffff0000
+#define AR5K_XRDELAY_CHIRP_DELAY_M	0xffff0000	/* Mask for CHIRP data delay */
 #define AR5K_XRDELAY_CHIRP_DELAY_S	16
 
 /*
  * XR timeout register
  */
-#define AR5K_XRTIMEOUT			0x80c8
-#define AR5K_XRTIMEOUT_CHIRP_M		0x0000ffff
+#define AR5K_XRTIMEOUT			0x80c8			/* Register Address */
+#define AR5K_XRTIMEOUT_CHIRP_M		0x0000ffff	/* Mask for CHIRP timeout */
 #define AR5K_XRTIMEOUT_CHIRP_S		0
-#define AR5K_XRTIMEOUT_POLL_M		0xffff0000
+#define AR5K_XRTIMEOUT_POLL_M		0xffff0000	/* Mask for Poll timeout */
 #define AR5K_XRTIMEOUT_POLL_S		16
 
 /*
  * XR chirp register
  */
-#define AR5K_XRCHIRP			0x80cc
-#define AR5K_XRCHIRP_SEND		0x00000001
-#define AR5K_XRCHIRP_GAP		0xffff0000
+#define AR5K_XRCHIRP			0x80cc			/* Register Address */
+#define AR5K_XRCHIRP_SEND		0x00000001	/* Send CHIRP */
+#define AR5K_XRCHIRP_GAP		0xffff0000	/* Mask for CHIRP gap (?) */
 
 /*
  * XR stomp register
  */
-#define AR5K_XRSTOMP			0x80d0
-#define AR5K_XRSTOMP_TX			0x00000001
-#define AR5K_XRSTOMP_RX_ABORT		0x00000002
-#define AR5K_XRSTOMP_RSSI_THRES		0x0000ff00
+#define AR5K_XRSTOMP			0x80d0			/* Register Address */
+#define AR5K_XRSTOMP_TX			0x00000001	/* Stomp Tx (?) */
+#define AR5K_XRSTOMP_RX			0x00000002	/* Stomp Rx (?) */
+#define AR5K_XRSTOMP_TX_RSSI		0x00000004	/* Stomp Tx RSSI (?) */
+#define AR5K_XRSTOMP_TX_BSSID		0x00000008	/* Stomp Tx BSSID (?) */
+#define AR5K_XRSTOMP_DATA		0x00000010	/* Stomp data (?)*/
+#define AR5K_XRSTOMP_RSSI_THRES		0x0000ff00	/* Mask for XR RSSI threshold */
 
 /*
  * First enhanced sleep register
  */
-#define AR5K_SLEEP0			0x80d4
-#define AR5K_SLEEP0_NEXT_DTIM		0x0007ffff
+#define AR5K_SLEEP0			0x80d4			/* Register Address */
+#define AR5K_SLEEP0_NEXT_DTIM		0x0007ffff	/* Mask for next DTIM (?) */
 #define AR5K_SLEEP0_NEXT_DTIM_S		0
-#define AR5K_SLEEP0_ASSUME_DTIM		0x00080000
-#define AR5K_SLEEP0_ENH_SLEEP_EN	0x00100000
-#define AR5K_SLEEP0_CABTO		0xff000000
+#define AR5K_SLEEP0_ASSUME_DTIM		0x00080000	/* Assume DTIM */
+#define AR5K_SLEEP0_ENH_SLEEP_EN	0x00100000	/* Enable enchanced sleep control */
+#define AR5K_SLEEP0_CABTO		0xff000000	/* Mask for CAB Time Out */
 #define AR5K_SLEEP0_CABTO_S		24
 
 /*
  * Second enhanced sleep register
  */
-#define AR5K_SLEEP1			0x80d8
-#define AR5K_SLEEP1_NEXT_TIM		0x0007ffff
+#define AR5K_SLEEP1			0x80d8			/* Register Address */
+#define AR5K_SLEEP1_NEXT_TIM		0x0007ffff	/* Mask for next TIM (?) */
 #define AR5K_SLEEP1_NEXT_TIM_S		0
-#define AR5K_SLEEP1_BEACON_TO		0xff000000
+#define AR5K_SLEEP1_BEACON_TO		0xff000000	/* Mask for Beacon Time Out */
 #define AR5K_SLEEP1_BEACON_TO_S		24
 
 /*
  * Third enhanced sleep register
  */
-#define AR5K_SLEEP2			0x80dc
-#define AR5K_SLEEP2_TIM_PER		0x0000ffff
+#define AR5K_SLEEP2			0x80dc			/* Register Address */
+#define AR5K_SLEEP2_TIM_PER		0x0000ffff	/* Mask for TIM period (?) */
 #define AR5K_SLEEP2_TIM_PER_S		0
-#define AR5K_SLEEP2_DTIM_PER		0xffff0000
+#define AR5K_SLEEP2_DTIM_PER		0xffff0000	/* Mask for DTIM period (?) */
 #define AR5K_SLEEP2_DTIM_PER_S		16
 
 /*
  * BSSID mask registers
  */
-#define AR5K_BSS_IDM0			0x80e0
-#define AR5K_BSS_IDM1			0x80e4
+#define AR5K_BSS_IDM0			0x80e0	/* Upper bits */
+#define AR5K_BSS_IDM1			0x80e4	/* Lower bits */
 
 /*
  * TX power control (TPC) register
+ *
+ * XXX: PCDAC steps (0.5dbm) or DBM ?
+ *
+ * XXX: Mask changes for newer chips to 7f
+ *      like tx power table ?
  */
-#define AR5K_TXPC			0x80e8
-#define AR5K_TXPC_ACK_M			0x0000003f
+#define AR5K_TXPC			0x80e8			/* Register Address */
+#define AR5K_TXPC_ACK_M			0x0000003f	/* Mask for ACK tx power */
 #define AR5K_TXPC_ACK_S			0
-#define AR5K_TXPC_CTS_M			0x00003f00
+#define AR5K_TXPC_CTS_M			0x00003f00	/* Mask for CTS tx power */
 #define AR5K_TXPC_CTS_S			8
-#define AR5K_TXPC_CHIRP_M		0x003f0000
+#define AR5K_TXPC_CHIRP_M		0x003f0000	/* Mask for CHIRP tx power */
 #define AR5K_TXPC_CHIRP_S		22
 
 /*
  * Profile count registers
  */
-#define AR5K_PROFCNT_TX			0x80ec
-#define AR5K_PROFCNT_RX			0x80f0
-#define AR5K_PROFCNT_RXCLR		0x80f4
-#define AR5K_PROFCNT_CYCLE		0x80f8
+#define AR5K_PROFCNT_TX			0x80ec	/* Tx count */
+#define AR5K_PROFCNT_RX			0x80f0	/* Rx count */
+#define AR5K_PROFCNT_RXCLR		0x80f4	/* Clear Rx count */
+#define AR5K_PROFCNT_CYCLE		0x80f8	/* Cycle count (?) */
+
+/*
+ * Quiet (period) control registers (?)
+ */
+#define AR5K_QUIET_CTL1			0x80fc			/* Register Address */
+#define AR5K_QUIET_CTL1_NEXT_QT		0x0000ffff	/* Mask for next quiet (period?) (?) */
+#define AR5K_QUIET_CTL1_QT_EN		0x00010000	/* Enable quiet (period?) */
+#define AR5K_QUIET_CTL2			0x8100			/* Register Address */
+#define AR5K_QUIET_CTL2_QT_PER		0x0000ffff	/* Mask for quiet period (?) */
+#define AR5K_QUIET_CTL2_QT_DUR		0xffff0000	/* Mask for quiet duration (?) */
 
 /*
  * TSF parameter register
  */
-#define AR5K_TSF_PARM			0x8104
-#define AR5K_TSF_PARM_INC_M		0x000000ff
+#define AR5K_TSF_PARM			0x8104			/* Register Address */
+#define AR5K_TSF_PARM_INC_M		0x000000ff	/* Mask for TSF increment */
 #define AR5K_TSF_PARM_INC_S		0
 
 /*
+ * QoS register (?)
+ */
+#define AR5K_QOS			0x8108			/* Register Address */
+#define AR5K_QOS_NOACK_2BIT_VALUES	0x00000000	/* (field) */
+#define AR5K_QOS_NOACK_BIT_OFFSET	0x00000020	/* (field) */
+#define AR5K_QOS_NOACK_BYTE_OFFSET	0x00000080	/* (field) */
+
+/*
  * PHY error filter register
  */
 #define AR5K_PHY_ERR_FIL		0x810c
-#define AR5K_PHY_ERR_FIL_RADAR		0x00000020
-#define AR5K_PHY_ERR_FIL_OFDM		0x00020000
-#define AR5K_PHY_ERR_FIL_CCK		0x02000000
+#define AR5K_PHY_ERR_FIL_RADAR		0x00000020	/* Radar signal */
+#define AR5K_PHY_ERR_FIL_OFDM		0x00020000	/* OFDM false detect (ANI) */
+#define AR5K_PHY_ERR_FIL_CCK		0x02000000	/* CCK false detect (ANI) */
+
+/*
+ * XR latency register
+ */
+#define AR5K_XRLAT_TX		0x8110
 
 /*
- * Rate duration register
+ * ACK SIFS register
+ */
+#define AR5K_ACKSIFS		0x8114			/* Register Address */
+#define AR5K_ACKSIFS_INC	0x00000000	/* ACK SIFS Increment (field) */
+
+/*
+ * MIC QoS control register (?)
+ */
+#define	AR5K_MIC_QOS_CTL	0x8118			/* Register Address */
+#define	AR5K_MIC_QOS_CTL_0	0x00000001	/* MIC QoS control 0 (?) */
+#define	AR5K_MIC_QOS_CTL_1	0x00000004	/* MIC QoS control 1 (?) */
+#define	AR5K_MIC_QOS_CTL_2	0x00000010	/* MIC QoS control 2 (?) */
+#define	AR5K_MIC_QOS_CTL_3	0x00000040	/* MIC QoS control 3 (?) */
+#define	AR5K_MIC_QOS_CTL_4	0x00000100	/* MIC QoS control 4 (?) */
+#define	AR5K_MIC_QOS_CTL_5	0x00000400	/* MIC QoS control 5 (?) */
+#define	AR5K_MIC_QOS_CTL_6	0x00001000	/* MIC QoS control 6 (?) */
+#define	AR5K_MIC_QOS_CTL_7	0x00004000	/* MIC QoS control 7 (?) */
+#define	AR5K_MIC_QOS_CTL_MQ_EN	0x00010000	/* Enable MIC QoS */
+
+/*
+ * MIC QoS select register (?)
+ */
+#define	AR5K_MIC_QOS_SEL	0x811c
+#define	AR5K_MIC_QOS_SEL_0	0x00000001
+#define	AR5K_MIC_QOS_SEL_1	0x00000010
+#define	AR5K_MIC_QOS_SEL_2	0x00000100
+#define	AR5K_MIC_QOS_SEL_3	0x00001000
+#define	AR5K_MIC_QOS_SEL_4	0x00010000
+#define	AR5K_MIC_QOS_SEL_5	0x00100000
+#define	AR5K_MIC_QOS_SEL_6	0x01000000
+#define	AR5K_MIC_QOS_SEL_7	0x10000000
+
+/*
+ * Misc mode control register (?)
+ */
+#define	AR5K_MISC_MODE			0x8120			/* Register Address */
+#define	AR5K_MISC_MODE_FBSSID_MATCH	0x00000001	/* Force BSSID match */
+#define	AR5K_MISC_MODE_ACKSIFS_MEM	0x00000002	/* ACK SIFS memory (?) */
+/* more bits */
+
+/*
+ * OFDM Filter counter
+ */
+#define	AR5K_OFDM_FIL_CNT		0x8124
+
+/*
+ * CCK Filter counter
+ */
+#define	AR5K_CCK_FIL_CNT		0x8128
+
+/*
+ * PHY Error Counters (?)
+ */
+#define	AR5K_PHYERR_CNT1		0x812c
+#define	AR5K_PHYERR_CNT1_MASK		0x8130
+
+#define	AR5K_PHYERR_CNT2		0x8134
+#define	AR5K_PHYERR_CNT2_MASK		0x8138
+
+/*
+ * TSF Threshold register (?)
+ */
+#define	AR5K_TSF_THRES			0x813c
+
+/*
+ * Rate -> ACK SIFS mapping table (32 entries)
+ */
+#define	AR5K_RATE_ACKSIFS_BASE		0x8680			/* Register Address */
+#define	AR5K_RATE_ACKSIFS(_n)		(AR5K_RATE_ACKSIFS_BSE + ((_n) << 2))
+#define	AR5K_RATE_ACKSIFS_NORMAL	0x00000001	/* Normal SIFS (field) */
+#define	AR5K_RATE_ACKSIFS_TURBO		0x00000400	/* Turbo SIFS (field) */
+
+/*
+ * Rate -> duration mapping table (32 entries)
  */
 #define AR5K_RATE_DUR_BASE		0x8700
 #define AR5K_RATE_DUR(_n)		(AR5K_RATE_DUR_BASE + ((_n) << 2))
 
+/*
+ * Rate -> db mapping table
+ * (8 entries, each one has 4 8bit fields)
+ */
+#define AR5K_RATE2DB_BASE		0x87c0
+#define AR5K_RATE2DB(_n)		(AR5K_RATE2DB_BASE + ((_n) << 2))
+
+/*
+ * db -> Rate mapping table
+ * (8 entries, each one has 4 8bit fields)
+ */
+#define AR5K_DB2RATE_BASE		0x87e0
+#define AR5K_DB2RATE(_n)		(AR5K_DB2RATE_BASE + ((_n) << 2))
+
 /*===5212 end===*/
 
 /*
@@ -1613,12 +1832,34 @@
 /*===PHY REGISTERS===*/
 
 /*
- * PHY register
+ * PHY registers start
  */
 #define	AR5K_PHY_BASE			0x9800
 #define	AR5K_PHY(_n)			(AR5K_PHY_BASE + ((_n) << 2))
-#define AR5K_PHY_SHIFT_2GHZ		0x00004007
-#define AR5K_PHY_SHIFT_5GHZ		0x00000007
+
+/*
+ * TST_2 (Misc config parameters)
+ */
+#define	AR5K_PHY_TST2			0x9800			/* Register Address */
+#define AR5K_PHY_TST2_TRIG_SEL		0x00000001	/* Trigger select (?) (field ?) */
+#define AR5K_PHY_TST2_TRIG		0x00000010	/* Trigger (?) (field ?) */
+#define AR5K_PHY_TST2_CBUS_MODE		0x00000100	/* Cardbus mode (?) */
+/* bit reserved */
+#define AR5K_PHY_TST2_CLK32		0x00000400	/* CLK_OUT is CLK32 (32Khz external) */
+#define AR5K_PHY_TST2_CHANCOR_DUMP_EN	0x00000800	/* Enable Chancor dump (?) */
+#define AR5K_PHY_TST2_EVEN_CHANCOR_DUMP	0x00001000	/* Even Chancor dump (?) */
+#define AR5K_PHY_TST2_RFSILENT_EN	0x00002000	/* Enable RFSILENT */
+#define AR5K_PHY_TST2_ALT_RFDATA	0x00004000	/* Alternate RFDATA (5-2GHz switch) */
+#define AR5K_PHY_TST2_MINI_OBS_EN	0x00008000	/* Enable mini OBS (?) */
+#define AR5K_PHY_TST2_RX2_IS_RX5_INV	0x00010000	/* 2GHz rx path is the 5GHz path inverted (?) */
+#define AR5K_PHY_TST2_SLOW_CLK160	0x00020000	/* Slow CLK160 (?) */
+#define AR5K_PHY_TST2_AGC_OBS_SEL_3	0x00040000	/* AGC OBS Select 3 (?) */
+#define AR5K_PHY_TST2_BBB_OBS_SEL	0x00080000	/* BB OBS Select (field ?) */
+#define AR5K_PHY_TST2_ADC_OBS_SEL	0x00800000	/* ADC OBS Select (field ?) */
+#define AR5K_PHY_TST2_RX_CLR_SEL	0x08000000	/* RX Clear Select (?) */
+#define AR5K_PHY_TST2_FORCE_AGC_CLR	0x10000000	/* Force AGC clear (?) */
+#define AR5K_PHY_SHIFT_2GHZ		0x00004007	/* Used to access 2GHz radios */
+#define AR5K_PHY_SHIFT_5GHZ		0x00000007	/* Used to access 5GHz radios (default) */
 
 /*
  * PHY frame control register [5110] /turbo mode register [5111+]
@@ -1630,18 +1871,21 @@
  * a "turbo mode register" for 5110. We treat this one as
  * a frame control register for 5110 below.
  */
-#define	AR5K_PHY_TURBO			0x9804
-#define	AR5K_PHY_TURBO_MODE		0x00000001
-#define	AR5K_PHY_TURBO_SHORT		0x00000002
+#define	AR5K_PHY_TURBO			0x9804			/* Register Address */
+#define	AR5K_PHY_TURBO_MODE		0x00000001	/* Enable turbo mode */
+#define	AR5K_PHY_TURBO_SHORT		0x00000002	/* Short mode (20Mhz channels) (?) */
 
 /*
  * PHY agility command register
+ * (aka TST_1)
  */
-#define	AR5K_PHY_AGC			0x9808
-#define	AR5K_PHY_AGC_DISABLE		0x08000000
+#define	AR5K_PHY_AGC			0x9808			/* Register Address */
+#define	AR5K_PHY_TST1			0x9808
+#define	AR5K_PHY_AGC_DISABLE		0x08000000	/* Disable AGC to A2 (?)*/
+#define	AR5K_PHY_TST1_TXHOLD		0x00003800	/* Set tx hold (?) */
 
 /*
- * PHY timing register [5112+]
+ * PHY timing register 3 [5112+]
  */
 #define	AR5K_PHY_TIMING_3		0x9814
 #define	AR5K_PHY_TIMING_3_DSC_MAN	0xfffe0000
@@ -1657,26 +1901,81 @@
 /*
  * PHY activation register
  */
-#define	AR5K_PHY_ACT			0x981c
-#define	AR5K_PHY_ACT_ENABLE		0x00000001
-#define	AR5K_PHY_ACT_DISABLE		0x00000002
+#define	AR5K_PHY_ACT			0x981c			/* Register Address */
+#define	AR5K_PHY_ACT_ENABLE		0x00000001	/* Activate PHY */
+#define	AR5K_PHY_ACT_DISABLE		0x00000002	/* Deactivate PHY */
+
+/*
+ * PHY RF control registers
+ * (i think these are delay times,
+ * these calibration values exist
+ * in EEPROM)
+ */
+#define AR5K_PHY_RF_CTL2		0x9824			/* Register Address */
+#define	AR5K_PHY_RF_CTL2_TXF2TXD_START	0x0000000f	/* Mask for TX frame to TX d(esc?) start */
+
+#define AR5K_PHY_RF_CTL3		0x9828			/* Register Address */
+#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON	0x0000000f	/* Mask for TX end to XLNA on */
+
+#define AR5K_PHY_RF_CTL4		0x9834			/* Register Address */
+#define AR5K_PHY_RF_CTL4_TXF2XPA_A_ON	0x00000001	/* TX frame to XPA A on (field) */
+#define AR5K_PHY_RF_CTL4_TXF2XPA_B_ON	0x00000100	/* TX frame to XPA B on (field) */
+#define	AR5K_PHY_RF_CTL4_TXE2XPA_A_OFF	0x00010000	/* TX end to XPA A off (field) */
+#define AR5K_PHY_RF_CTL4_TXE2XPA_B_OFF	0x01000000	/* TX end to XPA B off (field) */
+
+/*
+ * Pre-Amplifier control register
+ * (XPA -> external pre-amplifier)
+ */
+#define	AR5K_PHY_PA_CTL			0x9838			/* Register Address */
+#define	AR5K_PHY_PA_CTL_XPA_A_HI	0x00000001	/* XPA A high (?) */
+#define	AR5K_PHY_PA_CTL_XPA_B_HI	0x00000002	/* XPA B high (?) */
+#define	AR5K_PHY_PA_CTL_XPA_A_EN	0x00000004	/* Enable XPA A */
+#define	AR5K_PHY_PA_CTL_XPA_B_EN	0x00000008	/* Enable XPA B */
+
+/*
+ * PHY settling register
+ */
+#define AR5K_PHY_SETTLING		0x9844			/* Register Address */
+#define	AR5K_PHY_SETTLING_AGC		0x0000007f	/* Mask for AGC settling time */
+#define	AR5K_PHY_SETTLING_SWITCH	0x00003f80	/* Mask for Switch settlig time */
+
+/*
+ * PHY Gain registers
+ */
+#define AR5K_PHY_GAIN			0x9848			/* Register Address */
+#define	AR5K_PHY_GAIN_TXRX_ATTEN	0x0003f000	/* Mask for TX-RX Attenuation */
+
+#define	AR5K_PHY_GAIN_OFFSET		0x984c			/* Register Address */
+#define	AR5K_PHY_GAIN_OFFSET_RXTX_FLAG	0x00020000	/* RX-TX flag (?) */
+
+/*
+ * Desired size register
+ * (for more infos read ANI patent)
+ */
+#define AR5K_PHY_DESIRED_SIZE		0x9850			/* Register Address */
+#define	AR5K_PHY_DESIRED_SIZE_ADC	0x000000ff	/* Mask for ADC desired size */
+#define	AR5K_PHY_DESIRED_SIZE_PGA	0x0000ff00	/* Mask for PGA desired size */
+#define	AR5K_PHY_DESIRED_SIZE_TOT	0x0ff00000	/* Mask for Total desired size (?) */
 
 /*
  * PHY signal register
+ * (for more infos read ANI patent)
  */
-#define	AR5K_PHY_SIG			0x9858
-#define	AR5K_PHY_SIG_FIRSTEP		0x0003f000
+#define	AR5K_PHY_SIG			0x9858			/* Register Address */
+#define	AR5K_PHY_SIG_FIRSTEP		0x0003f000	/* Mask for FIRSTEP */
 #define	AR5K_PHY_SIG_FIRSTEP_S		12
-#define	AR5K_PHY_SIG_FIRPWR		0x03fc0000
+#define	AR5K_PHY_SIG_FIRPWR		0x03fc0000	/* Mask for FIPWR */
 #define	AR5K_PHY_SIG_FIRPWR_S		18
 
 /*
  * PHY coarse agility control register
+ * (for more infos read ANI patent)
  */
-#define	AR5K_PHY_AGCCOARSE		0x985c
-#define	AR5K_PHY_AGCCOARSE_LO		0x00007f80
+#define	AR5K_PHY_AGCCOARSE		0x985c			/* Register Address */
+#define	AR5K_PHY_AGCCOARSE_LO		0x00007f80	/* Mask for AGC Coarse low */
 #define	AR5K_PHY_AGCCOARSE_LO_S		7
-#define	AR5K_PHY_AGCCOARSE_HI		0x003f8000
+#define	AR5K_PHY_AGCCOARSE_HI		0x003f8000	/* Mask for AGC Coarse high */
 #define	AR5K_PHY_AGCCOARSE_HI_S		15
 
 /*
@@ -1689,12 +1988,13 @@
 /*
  * PHY noise floor status register
  */
-#define AR5K_PHY_NF			0x9864
-#define AR5K_PHY_NF_M			0x000001ff
-#define AR5K_PHY_NF_ACTIVE		0x00000100
+#define AR5K_PHY_NF			0x9864			/* Register address */
+#define AR5K_PHY_NF_M			0x000001ff	/* Noise floor mask */
+#define AR5K_PHY_NF_ACTIVE		0x00000100	/* Noise floor calibration still active */
 #define AR5K_PHY_NF_RVAL(_n)		(((_n) >> 19) & AR5K_PHY_NF_M)
 #define AR5K_PHY_NF_AVAL(_n)		(-((_n) ^ AR5K_PHY_NF_M) + 1)
 #define AR5K_PHY_NF_SVAL(_n)		(((_n) & AR5K_PHY_NF_M) | (1 << 9))
+#define	AR5K_PHY_NF_THRESH62		0x00001000	/* Thresh62 -check ANI patent- (field) */
 
 /*
  * PHY ADC saturation register [5110]
@@ -1706,6 +2006,30 @@
 #define	AR5K_PHY_ADCSAT_THR_S		5
 
 /*
+ * PHY Weak ofdm signal detection threshold registers (ANI) [5212+]
+ */
+
+/* High thresholds */
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR		0x9868
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT	0x0000001f
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_COUNT_S	0
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1		0x00fe0000
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M1_S	17
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2		0x7f000000
+#define AR5K_PHY_WEAK_OFDM_HIGH_THR_M2_S	24
+
+/* Low thresholds */
+#define AR5K_PHY_WEAK_OFDM_LOW_THR 		0x986c
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_SELFCOR_EN	0x00000001
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT	0x00003f00
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_COUNT_S	8
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1		0x001fc000
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M1_S		14
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2		0x0fe00000
+#define AR5K_PHY_WEAK_OFDM_LOW_THR_M2_S		21
+
+
+/*
  * PHY sleep registers [5112+]
  */
 #define AR5K_PHY_SCR			0x9870
@@ -1730,6 +2054,8 @@
 					AR5K_PHY_PLL_44MHZ_5211 : AR5K_PHY_PLL_44MHZ_5212)
 #define AR5K_PHY_PLL_RF5111		0x00000000
 #define AR5K_PHY_PLL_RF5112		0x00000040
+#define	AR5K_PHY_PLL_HALF_RATE		0x00000100
+#define	AR5K_PHY_PLL_QUARTER_RATE	0x00000200
 
 /*
  * RF Buffer register
@@ -1792,23 +2118,74 @@
 #define AR5K_PHY_RFSTG_DISABLE		0x00000021
 
 /*
+ * PHY Antenna control register
+ */
+#define AR5K_PHY_ANT_CTL		0x9910			/* Register Address */
+#define	AR5K_PHY_ANT_CTL_TXRX_EN	0x00000001	/* Enable TX/RX (?) */
+#define	AR5K_PHY_ANT_CTL_SECTORED_ANT	0x00000004	/* Sectored Antenna */
+#define	AR5K_PHY_ANT_CTL_HITUNE5	0x00000008	/* Hitune5 (?) */
+#define	AR5K_PHY_ANT_CTL_SWTABLE_IDLE	0x00000010	/* Switch table idle (?) */
+
+/*
  * PHY receiver delay register [5111+]
  */
-#define	AR5K_PHY_RX_DELAY		0x9914
-#define	AR5K_PHY_RX_DELAY_M		0x00003fff
+#define	AR5K_PHY_RX_DELAY		0x9914			/* Register Address */
+#define	AR5K_PHY_RX_DELAY_M		0x00003fff	/* Mask for RX activate to receive delay (/100ns) */
+
+/*
+ * PHY max rx length register (?) [5111]
+ */
+#define	AR5K_PHY_MAX_RX_LEN		0x991c
 
 /*
- * PHY timing I(nphase) Q(adrature) control register [5111+]
+ * PHY timing register 4
+ * I(nphase)/Q(adrature) calibration register [5111+]
  */
-#define	AR5K_PHY_IQ			0x9920		/* Register address */
+#define	AR5K_PHY_IQ			0x9920			/* Register Address */
 #define	AR5K_PHY_IQ_CORR_Q_Q_COFF	0x0000001f	/* Mask for q correction info */
 #define	AR5K_PHY_IQ_CORR_Q_I_COFF	0x000007e0	/* Mask for i correction info */
 #define	AR5K_PHY_IQ_CORR_Q_I_COFF_S	5
 #define	AR5K_PHY_IQ_CORR_ENABLE		0x00000800	/* Enable i/q correction */
-#define	AR5K_PHY_IQ_CAL_NUM_LOG_MAX	0x0000f000
+#define	AR5K_PHY_IQ_CAL_NUM_LOG_MAX	0x0000f000	/* Mask for max number of samples in log scale */
 #define	AR5K_PHY_IQ_CAL_NUM_LOG_MAX_S	12
 #define	AR5K_PHY_IQ_RUN			0x00010000	/* Run i/q calibration */
+#define	AR5K_PHY_IQ_USE_PT_DF		0x00020000	/* Use pilot track df (?) */
+#define	AR5K_PHY_IQ_EARLY_TRIG_THR	0x00200000	/* Early trigger threshold (?) (field) */
+#define	AR5K_PHY_IQ_PILOT_MASK_EN	0x10000000	/* Enable pilot mask (?) */
+#define	AR5K_PHY_IQ_CHAN_MASK_EN	0x20000000	/* Enable channel mask (?) */
+#define	AR5K_PHY_IQ_SPUR_FILT_EN	0x40000000	/* Enable spur filter */
+#define	AR5K_PHY_IQ_SPUR_RSSI_EN	0x80000000	/* Enable spur rssi */
 
+/*
+ * PHY timing register 5
+ * OFDM Self-correlator Cyclic RSSI threshold params
+ * (Check out bb_cycpwr_thr1 on ANI patent)
+ */
+#define	AR5K_PHY_OFDM_SELFCORR			0x9924			/* Register Address */
+#define	AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_EN	0x00000001	/* Enable cyclic RSSI thr 1 */
+#define	AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1	0x000000fe	/* Mask for Cyclic RSSI threshold 1 */
+#define	AR5K_PHY_OFDM_SELFCORR_CYPWR_THR3	0x00000100	/* Cyclic RSSI threshold 3 (field) (?) */
+#define	AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR_EN	0x00008000	/* Enable 1A RSSI threshold (?) */
+#define	AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR	0x00010000	/* 1A RSSI threshold (field) (?) */
+#define	AR5K_PHY_OFDM_SELFCORR_LSCTHR_HIRSSI	0x00800000	/* Long sc threshold hi rssi (?) */
+
+/*
+ * PHY-only warm reset register
+ */
+#define	AR5K_PHY_WARM_RESET		0x9928
+
+/*
+ * PHY-only control register
+ */
+#define AR5K_PHY_CTL			0x992c			/* Register Address */
+#define	AR5K_PHY_CTL_RX_DRAIN_RATE	0x00000001	/* RX drain rate (?) */
+#define	AR5K_PHY_CTL_LATE_TX_SIG_SYM	0x00000002	/* Late tx signal symbol (?) */
+#define	AR5K_PHY_CTL_GEN_SCRAMBLER	0x00000004	/* Generate scrambler */
+#define	AR5K_PHY_CTL_TX_ANT_SEL		0x00000008	/* TX antenna select */
+#define	AR5K_PHY_CTL_TX_ANT_STATIC	0x00000010	/* Static TX antenna */
+#define	AR5K_PHY_CTL_RX_ANT_SEL		0x00000020	/* RX antenna select */
+#define	AR5K_PHY_CTL_RX_ANT_STATIC	0x00000040	/* Static RX antenna */
+#define	AR5K_PHY_CTL_LOW_FREQ_SLE_EN	0x00000080	/* Enable low freq sleep */
 
 /*
  * PHY PAPD probe register [5111+ (?)]
@@ -1816,9 +2193,13 @@
  * Because it's always 0 in 5211 initialization code
  */
 #define	AR5K_PHY_PAPD_PROBE		0x9930
+#define	AR5K_PHY_PAPD_PROBE_SH_HI_PAR	0x00000001
+#define	AR5K_PHY_PAPD_PROBE_PCDAC_BIAS	0x00000002
+#define	AR5K_PHY_PAPD_PROBE_COMP_GAIN	0x00000040
 #define	AR5K_PHY_PAPD_PROBE_TXPOWER	0x00007e00
 #define	AR5K_PHY_PAPD_PROBE_TXPOWER_S	9
 #define	AR5K_PHY_PAPD_PROBE_TX_NEXT	0x00008000
+#define	AR5K_PHY_PAPD_PROBE_PREDIST_EN	0x00010000
 #define	AR5K_PHY_PAPD_PROBE_TYPE	0x01800000	/* [5112+] */
 #define	AR5K_PHY_PAPD_PROBE_TYPE_S	23
 #define	AR5K_PHY_PAPD_PROBE_TYPE_OFDM	0
@@ -1848,15 +2229,16 @@
 #define	AR5K_PHY_FRAME_CTL		(ah->ah_version == AR5K_AR5210 ? \
 					AR5K_PHY_FRAME_CTL_5210 : AR5K_PHY_FRAME_CTL_5211)
 /*---[5111+]---*/
-#define	AR5K_PHY_FRAME_CTL_TX_CLIP	0x00000038
+#define	AR5K_PHY_FRAME_CTL_TX_CLIP	0x00000038	/* Mask for tx clip (?) */
 #define	AR5K_PHY_FRAME_CTL_TX_CLIP_S	3
+#define	AR5K_PHY_FRAME_CTL_PREP_CHINFO	0x00010000	/* Prepend chan info */
 /*---[5110/5111]---*/
-#define	AR5K_PHY_FRAME_CTL_TIMING_ERR	0x01000000
-#define	AR5K_PHY_FRAME_CTL_PARITY_ERR	0x02000000
-#define	AR5K_PHY_FRAME_CTL_ILLRATE_ERR	0x04000000	/* illegal rate */
-#define	AR5K_PHY_FRAME_CTL_ILLLEN_ERR	0x08000000	/* illegal length */
+#define	AR5K_PHY_FRAME_CTL_TIMING_ERR	0x01000000	/* PHY timing error */
+#define	AR5K_PHY_FRAME_CTL_PARITY_ERR	0x02000000	/* Parity error */
+#define	AR5K_PHY_FRAME_CTL_ILLRATE_ERR	0x04000000	/* Illegal rate */
+#define	AR5K_PHY_FRAME_CTL_ILLLEN_ERR	0x08000000	/* Illegal length */
 #define	AR5K_PHY_FRAME_CTL_SERVICE_ERR	0x20000000
-#define	AR5K_PHY_FRAME_CTL_TXURN_ERR	0x40000000	/* tx underrun */
+#define	AR5K_PHY_FRAME_CTL_TXURN_ERR	0x40000000	/* TX underrun */
 #define AR5K_PHY_FRAME_CTL_INI		AR5K_PHY_FRAME_CTL_SERVICE_ERR | \
 			AR5K_PHY_FRAME_CTL_TXURN_ERR | \
 			AR5K_PHY_FRAME_CTL_ILLLEN_ERR | \
@@ -1915,6 +2297,11 @@ after DFS is enabled */
 #define AR5K_PHY_ANT_SWITCH_TABLE_1	0x9964
 
 /*
+ * PHY Noise floor threshold
+ */
+#define AR5K_PHY_NFTHRES		0x9968
+
+/*
  * PHY clock sleep registers [5112+]
  */
 #define AR5K_PHY_SCLOCK			0x99f0
@@ -1922,56 +2309,116 @@ after DFS is enabled */
 #define AR5K_PHY_SDELAY			0x99f4
 #define AR5K_PHY_SDELAY_32MHZ		0x000000ff
 #define AR5K_PHY_SPENDING		0x99f8
+#define	AR5K_PHY_SPENDING_14		0x00000014
+#define	AR5K_PHY_SPENDING_18		0x00000018
 #define AR5K_PHY_SPENDING_RF5111	0x00000018
-#define AR5K_PHY_SPENDING_RF5112	0x00000014 /* <- i 've only seen this on 2425 dumps ! */
-#define AR5K_PHY_SPENDING_RF5112A	0x0000000e /* but since i only have 5112A-based chips */
-#define AR5K_PHY_SPENDING_RF5424	0x00000012 /* to test it might be also for old 5112.  */
+#define AR5K_PHY_SPENDING_RF5112	0x00000014
+/* #define AR5K_PHY_SPENDING_RF5112A	0x0000000e */
+/* #define AR5K_PHY_SPENDING_RF5424	0x00000012 */
+#define	AR5K_PHY_SPENDING_RF5413	0x00000014
+#define	AR5K_PHY_SPENDING_RF2413	0x00000014
+#define AR5K_PHY_SPENDING_RF2425	0x00000018
 
 /*
  * Misc PHY/radio registers [5110 - 5111]
  */
-#define	AR5K_BB_GAIN_BASE		0x9b00 /* BaseBand Amplifier Gain table base address */
+#define	AR5K_BB_GAIN_BASE		0x9b00	/* BaseBand Amplifier Gain table base address */
 #define AR5K_BB_GAIN(_n)		(AR5K_BB_GAIN_BASE + ((_n) << 2))
-#define	AR5K_RF_GAIN_BASE		0x9a00 /* RF Amplrifier Gain table base address */
+#define	AR5K_RF_GAIN_BASE		0x9a00	/* RF Amplrifier Gain table base address */
 #define AR5K_RF_GAIN(_n)		(AR5K_RF_GAIN_BASE + ((_n) << 2))
 
 /*
  * PHY timing IQ calibration result register [5111+]
  */
-#define	AR5K_PHY_IQRES_CAL_PWR_I	0x9c10 /* I (Inphase) power value */
-#define	AR5K_PHY_IQRES_CAL_PWR_Q	0x9c14 /* Q (Quadrature) power value */
+#define	AR5K_PHY_IQRES_CAL_PWR_I	0x9c10	/* I (Inphase) power value */
+#define	AR5K_PHY_IQRES_CAL_PWR_Q	0x9c14	/* Q (Quadrature) power value */
 #define	AR5K_PHY_IQRES_CAL_CORR		0x9c18	/* I/Q Correlation */
 
 /*
  * PHY current RSSI register [5111+]
  */
-#define	AR5K_PHY_CURRENT_RSSI		0x9c1c
+#define	AR5K_PHY_CURRENT_RSSI	0x9c1c
+
+/*
+ * PHY RF Bus grant register (?)
+ */
+#define	AR5K_PHY_RFBUS_GRANT	0x9c20
+
+/*
+ * PHY ADC test register
+ */
+#define	AR5K_PHY_ADC_TEST	0x9c24
+#define	AR5K_PHY_ADC_TEST_I	0x00000001
+#define	AR5K_PHY_ADC_TEST_Q	0x00000200
+
+/*
+ * PHY DAC test register
+ */
+#define	AR5K_PHY_DAC_TEST	0x9c28
+#define	AR5K_PHY_DAC_TEST_I	0x00000001
+#define	AR5K_PHY_DAC_TEST_Q	0x00000200
+
+/*
+ * PHY PTAT register (?)
+ */
+#define	AR5K_PHY_PTAT		0x9c2c
+
+/*
+ * PHY Illegal TX rate register [5112+]
+ */
+#define	AR5K_PHY_BAD_TX_RATE	0x9c30
+
+/*
+ * PHY SPUR Power register [5112+]
+ */
+#define	AR5K_PHY_SPUR_PWR	0x9c34			/* Register Address */
+#define	AR5K_PHY_SPUR_PWR_I	0x00000001	/* SPUR Power estimate for I (field) */
+#define	AR5K_PHY_SPUR_PWR_Q	0x00000100	/* SPUR Power estimate for Q (field) */
+#define	AR5K_PHY_SPUR_PWR_FILT	0x00010000	/* Power with SPUR removed (field) */
+
+/*
+ * PHY Channel status register [5112+] (?)
+ */
+#define	AR5K_PHY_CHAN_STATUS		0x9c38
+#define	AR5K_PHY_CHAN_STATUS_BT_ACT	0x00000001
+#define	AR5K_PHY_CHAN_STATUS_RX_CLR_RAW	0x00000002
+#define	AR5K_PHY_CHAN_STATUS_RX_CLR_MAC	0x00000004
+#define	AR5K_PHY_CHAN_STATUS_RX_CLR_PAP	0x00000008
+
+/*
+ * PHY PAPD I (power?) table (?)
+ * (92! entries)
+ */
+#define	AR5K_PHY_PAPD_I_BASE	0xa000
+#define	AR5K_PHY_PAPD_I(_n)	(AR5K_PHY_PAPD_I_BASE + ((_n) << 2))
 
 /*
  * PHY PCDAC TX power table
  */
 #define	AR5K_PHY_PCDAC_TXPOWER_BASE_5211	0xa180
-#define AR5K_PHY_PCDAC_TXPOWER_BASE_5413	0xa280
-#define AR5K_PHY_PCDAC_TXPOWER_BASE	(ah->ah_radio >= AR5K_RF5413 ? \
-					AR5K_PHY_PCDAC_TXPOWER_BASE_5413 :\
+#define AR5K_PHY_PCDAC_TXPOWER_BASE_2413	0xa280
+#define AR5K_PHY_PCDAC_TXPOWER_BASE	(ah->ah_radio >= AR5K_RF2413 ? \
+					AR5K_PHY_PCDAC_TXPOWER_BASE_2413 :\
 					AR5K_PHY_PCDAC_TXPOWER_BASE_5211)
 #define	AR5K_PHY_PCDAC_TXPOWER(_n)	(AR5K_PHY_PCDAC_TXPOWER_BASE + ((_n) << 2))
 
 /*
  * PHY mode register [5111+]
  */
-#define	AR5K_PHY_MODE			0x0a200		/* Register address */
-#define	AR5K_PHY_MODE_MOD		0x00000001	/* PHY Modulation mask*/
+#define	AR5K_PHY_MODE			0x0a200			/* Register Address */
+#define	AR5K_PHY_MODE_MOD		0x00000001	/* PHY Modulation bit */
 #define AR5K_PHY_MODE_MOD_OFDM		0
 #define AR5K_PHY_MODE_MOD_CCK		1
-#define AR5K_PHY_MODE_FREQ		0x00000002	/* Freq mode mask */
+#define AR5K_PHY_MODE_FREQ		0x00000002	/* Freq mode bit */
 #define	AR5K_PHY_MODE_FREQ_5GHZ		0
 #define	AR5K_PHY_MODE_FREQ_2GHZ		2
-#define AR5K_PHY_MODE_MOD_DYN		0x00000004	/* Dynamic OFDM/CCK mode mask [5112+] */
+#define AR5K_PHY_MODE_MOD_DYN		0x00000004	/* Enable Dynamic OFDM/CCK mode [5112+] */
 #define AR5K_PHY_MODE_RAD		0x00000008	/* [5212+] */
 #define AR5K_PHY_MODE_RAD_RF5111	0
 #define AR5K_PHY_MODE_RAD_RF5112	8
-#define AR5K_PHY_MODE_XR		0x00000010	/* [5112+] */
+#define AR5K_PHY_MODE_XR		0x00000010	/* Enable XR mode [5112+] */
+#define	AR5K_PHY_MODE_HALF_RATE		0x00000020	/* Enable Half rate (test) */
+#define	AR5K_PHY_MODE_QUARTER_RATE	0x00000040	/* Enable Quarter rat (test) */
 
 /*
  * PHY CCK transmit control register [5111+ (?)]
@@ -1979,6 +2426,15 @@ after DFS is enabled */
 #define AR5K_PHY_CCKTXCTL		0xa204
 #define AR5K_PHY_CCKTXCTL_WORLD		0x00000000
 #define AR5K_PHY_CCKTXCTL_JAPAN		0x00000010
+#define	AR5K_PHY_CCKTXCTL_SCRAMBLER_DIS	0x00000001
+#define	AR5K_PHY_CCKTXCTK_DAC_SCALE	0x00000004
+
+/*
+ * PHY CCK Cross-correlator Barker RSSI threshold register [5212+]
+ */
+#define AR5K_PHY_CCK_CROSSCORR			0xa208
+#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR	0x0000000f
+#define AR5K_PHY_CCK_CROSSCORR_WEAK_SIG_THR_S	0
 
 /*
  * PHY 2GHz gain register [5111+]
author	Hauke Mehrtens <hauke@hauke-m.de>	2008-09-05 18:40:23 +0200
committer	Luis R. Rodriguez <lrodriguez@atheros.com>	2008-09-05 10:53:48 -0700
commit	e3dabd8797267e70bf6ab72ced274855489b1035 (patch)
tree	00301a1b4486db212835d45ec026054d61296d90
parent	884c73f54a2d10a49aa166daf0daa76b4b8d60d5 (diff)
download	compat-wireless-2.6-old-e3dabd8797267e70bf6ab72ced274855489b1035.tar.gz