1st set of IIO new device support, features and cleanup for 6.8

New device support
------------------

adi,hmc425a
  * Add support for ADRF5740 attenuators.  Minor changes to driver needed
    alongside new IDs.
aosong,ags02ma
  * New driver for this volatile organic compounds sensor.
bosch,bmp280
  * Add BMP390 (small amount of refactoring + ID)
bosch,bmi323
  * New driver to support the BMI323 6-axis IMU.
honeywell,hsc030pa
  * New driver supporting a huge number of SSC and HSC series pressure and
    temperature sensors.
isil,isl76682
  * New driver for this simple Ambient Light sensor.
liteon,ltr390
  * New driver for this ambient and ultraviolet light sensor.
maxim,max34408
  * New driver to support the MAX34408 and MAX34409 current monitoring ADCs.
melexis,mlx90635
  * New driver for this Infrared contactless temperature sensor.
mirochip,mcp9600
  * New driver for this thermocouple EMF convertor.
ti,hdc3020
  * New driver for this integrated relative humidity and temperature
    sensor.
vishay,veml6075
  * New driver for this UVA and UVB light sensor.

General features
----------------

Device properties
  * Add fwnode_property_match_property_string() helper to allow matching
    single value property against an array of predefined strings.
  * Use fwnode_property_string_array_count() inside
    fwnode_property_match_string() instead of open coding the same.
checkpatch.pl
  * Add exclusion of __aligned() from a warning reducing false positives
    on IIO drivers (and hopefully beyond)

IIO Features
------------

core
  * New light channel modifiers for UVA and UVB.
  * Add IIO_CHAN_INFO_TROUGH as counterpart to IIO_CHAN_INFO_PEAK so that
    we can support device that keep running track of the lowest value they
    have seen in similar fashion to the existing peak tracking.
adi,adis library
  * Use spi cs inactive delay even when a burst reading is performed.
    As it's now used every time, can centralize the handling in the SPI
    setup code in the driver.
adi,ad2s1210
  * Support for fixed-mode to this resolver driver where the A0 and A1
    pins are hard wired to config mode in which case position and config
    must be read from appropriate config registers.
  * Support reset GPIO if present.
adi,ad5791
  * Allow configuration of presence of external amplifier in DT binding.
adi,adis16400
  * Add spi-cs-inactive-delay-ns to bindings to allow it to be tweaked
    if default delays are not quite enough for a specific board.
adi,adis16475
  * Add spi-cs-inactive-delay-ns to bindings to allow it to be tweaked
    if default delays are not quite enough for a specific board.
bosch,bmp280
  * Enable multiple chip IDs per family of devices.
rohm,bu27008
  * Add an illuminance channel calculated from RGB and IR data.

Cleanup
-------

Minor white space, typos and tidy up not explicitly called out.

Core
  * Check that the available_scan_masks array passed to the IIO core
    by a driver is sensible by ensuring the entries are ordered so the
    minimum number of channels is enabled in the earlier entries (as they
    will be selected if sufficient for the requested channels).
  * Document that the available_scan_masks infrastructure doesn't currently
    handle masks that don't fit in a long int.
  * Improve intensity documentation to reflect that there is no expectation
    of sensible units (it's dependent on a frequency sensitivity curve)
Various
  * Use new device_property_match_property_string() to replace open coded
    versions of the same thing.
  * Fix a few MAINTAINERS filenames.
  * i2c_get_match_data() and spi_get_device_match_data() pushed into
    more drivers reducing boilerplate handling.
  * Some unnecessary headers removed.
  * ACPI_PTR() removals. It's rarely worth using this.
adi,ad7091r (early part of a series adding device support - useful in
  their own right)
  * Pass iio_dev directly an event handler rather than relying
    on broken use of dev_get_drvdata() as drvdata is never set in this driver.
  * Make sure alert is turned on.
adi,ad9467 (general driver fixing up as precursor to iio-backend proposal
  which is under review for 6.9)
  * Fix reset gpio handling to match expected polarity.
  * Always handle error codes from spi_writes.
  * Add a driver instance local mutex to avoid some races.
  * Fix scale setting to align with available scale values.
  * Split array of chip_info structures up into named individual elements.
  * Convert to regmap.
honeywell,mprls0025pa
  * Drop now unnecessary type references in DT binding for properties in
    pascals.
invensense,mpu6050
  * Don't eat a potentially useful return value from regmap_bulk_write()
invensense,icm42600
  * Use max macro to improve code readability and save a few lines.
liteon,ltrf216a
  * Improve prevision of light intensity.
microchip,mcp3911
  * Use cleanup.h magic.
qcom,spmi*
  * Fix wrong descriptions of SPMI reg fields in bindings.

Other
----

mailmap
  * Update for Matt Ranostay
-----BEGIN PGP SIGNATURE-----
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=jH+G
-----END PGP SIGNATURE-----