| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In practice it's unlikely anyone would try to set the integration time
to 0 which isn't in the available list and if they did then they would
get index 12 which whilst reserved on the device fits in the field.
However a compiler might get half way through this reasoning and that
might be the cause of
> >> drivers/iio/light/opt4001.c:215:9: error: call to '__compiletime_assert_355' declared with 'error' attribute: FIELD_PREP: value too large for the field
> 215 | reg |= FIELD_PREP(OPT4001_CTRL_CONV_TIME_MASK, chip->int_time);
Even if this isn't the cause, it looks like a bug to me.
Fixes: 9a9608418292 ("iio: light: Add support for TI OPT4001 light sensor")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202308061902.0gVz6bSe-lkp@intel.com/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add documentation for the use of the bypass filter mode.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230731084928.8302-2-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add filter bypass mode, which bypasses the low pass filter, high pass
filter and disables/unregister the clock rate notifier.
Currently a feature like bypassing the filter is not achievable
straightforward and not very deductive. The user has to look through the
code and call the set_lpf_3db_frequency and set_hpf_3db_frequency iio
attributes from the user interface using the corner cases (freq >
largest lpf supported by the part, respectively freq < smallest hpf
supported by the part). Moreover, in such case of bypassing the filter,
the input clock rate change might mess up things so we want to make sure
that it is disabled. Also, the feature will help emphasizing the filter
behavior, therefore adding it in the userspace will ease the
charcaterization of the filter's effects when active/disabled.
It was requested by users of the driver to ease the interaction with
different configuration modes of the device.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230731084928.8302-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ROHM BU27010 is an RGBC sensor with a flickering detection FIFO. The
RGBC+IR sensor functionality is largely similar to what the BU27008 has.
There are some notable things though:
- gain setting is once again new and exotic. Now, there is 6bit gain
setting where 4 of the bits are common to all channels and 2 bits
can be configured separately for each channel. The BU27010 has
similar "1X on other channels vs 2X on IR when selector is 0x0"
gain design as BU27008 had. So, we use same gain setting policy for
BU27010 as we did for BU27008 - driver sets same gain selector for all
channels but shows the gains separately for all channels so users
can (at least in theory) detect this 1X vs 2X madness...
- BU27010 has suffled all the control register bitfields to new
addresses and bit positions while still keeping the register naming
same.
- Some more power/reset control is added.
- FIFO for "flickering detection" is added.
The control register suffling made this slightly nasty. Still, it is
easier for maintenance perspective to add the BU27010 support in BU27008
driver because - even though the bit positions/addresses were changed -
most of the driver structure can be re-used. Writing own driver for
BU27010 would mean plenty of duplicate code albeit a tad more clarity.
The flickering FIFO is not supported by the driver.
Add BU27010 RGBC+IR support to rohm-bu27008 driver.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/111cd217ccece1c1f16ab4287532dc4e1ddb8a3f.1690958450.git.mazziesaccount@gmail.com
|
|
The ROHM BU27010 RGB + flickering sensor is in many regards similar to
the BU27008. Prepare for adding support for BU27010 by allowing
chip-specific properties to be brought from the of_device_id data.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/d5994648033d5513993b8d72eb186ddda211b5ac.1690958450.git.mazziesaccount@gmail.com
|
|
The ROHM BU27010 is a sensor with 6 photodiodes (red, green, blue, clear,
IR and flickering detection) with five configurable channels. Red, green
and flickering detection being always available and two out of the rest
three (blue, clear, IR) can be selected to be simultaneously measured.
Typical application is adjusting LCD/OLED backlight of TVs, mobile phones
and tablet PCs.
Add binding document for ROHM BU27010.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/717d30694ba6864b8c28772d7478bed93ea10138.1690958450.git.mazziesaccount@gmail.com
|
|
MCP4728 is a 12-bit quad channel DAC with I2C interface.
support for:
* per-channel gain
* per-channel power state
* per-channel power down mode control
* per-channel vref selection internal/vdd
* store current state to on-chip EEPROM
Signed-off-by: Andrea Collamati <andrea.collamati@gmail.com>
Link: https://lore.kernel.org/r/a0933003ed3c855f9d80d6ce0a40add2b6f0ba36.1691066050.git.andrea.collamati@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add documentation for MCP4728
Signed-off-by: Andrea Collamati <andrea.collamati@gmail.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/d93dd116cfa7f958c038c0c62993071ea48451d2.1691066050.git.andrea.collamati@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add regulators for the VCC supplies of the admv1013.
The patch aims to align the implementation with the current admv1014
driver where all the VCC supplies are handled as regulators.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230731094455.26742-2-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add bindings for the VCC regulators of the ADMV1013 microware
upconverter.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230731094455.26742-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This function call was found to be unnecessary as there is no equivalent
platform_get_drvdata() call to access the private data of the driver. Also,
the private data is defined in this driver, so there is no risk of it being
accessed outside of this driver file.
Reviewed-by: Alexandru Ardelean <alex@shruggie.ro>
Signed-off-by: Andrei Coardos <aboutphysycs@gmail.com>
Link: https://lore.kernel.org/r/20230802120915.25631-1-aboutphysycs@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The module_mcb_driver() will set "THIS_MODULE" to driver.owner when
register a mcb_driver, so it is redundant initialization to set
driver.owner in men_z188_driver statement. Remove it for clean code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230804100938.100435-1-lizetao1@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make the regulators required in the dt bindings.
Despite the fact that the datasheet is not explicit enough, all the
specifications of the part are built around these pins being supplied.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230731144404.389255-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
fwnode_irq_get[_byname]() were changed to not return 0 anymore. The
special error case where device-tree based IRQ mapping fails can't no
longer be reliably detected from this return value. This yields a
functional change in the driver where the mapping failure is treated as
an error.
The mapping failure can occur for example when the device-tree IRQ
information translation call-back(s) (xlate) fail, IRQ domain is not
found, IRQ type conflicts, etc. In most cases this indicates an error in
the device-tree and special handling is not really required.
One more thing to note is that ACPI APIs do not return zero for any
failures so this special handling did only apply on device-tree based
systems.
Drop the special handling for DT mapping failures as these can no longer
be separated from other errors at driver side. Change all failures in
IRQ getting to be handled by continuing without the events instead of
aborting the probe upon certain errors.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/3ad1c6f195ead3dfa8711235e1dead139d27f700.1690890774.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
fwnode_irq_get() was changed to not return 0 anymore.
Drop check for return value 0.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/9e18cf49a8bb581a84c3fa548ea577e2a3eb840d.1690890774.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There is no possible for platform_get_irq() to return 0
and the return value of platform_get_irq() is more sensible
to show the error reason.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230727131607.2897937-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In function size_from_channelarray(), the return value 'bytes' is defined
as int type. However, the calcution of 'bytes' in this function is designed
to use the unsigned int type. So it is necessary to change 'bytes' type to
unsigned int to avoid integer overflow.
The size_from_channelarray() is called in main() function, its return value
is directly multipled by 'buf_len' and then used as the malloc() parameter.
The 'buf_len' is completely controllable by user, thus a multiplication
overflow may occur here. This could allocate an unexpected small area.
Signed-off-by: Chenyuan Mi <michenyuan@huawei.com>
Link: https://lore.kernel.org/r/20230725092407.62545-1-michenyuan@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace device_get_match_data() and i2c_match_id() by i2c_get_match
_data() by making similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230723102743.102284-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace of_device_get_match_data() and i2c_match_id() by i2c_get_match
_data() by making similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230723105209.175545-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The `scripts/kernel-doc -v -none -Wall` reports several issues
with the kernel doc in IIO core C file. Update the comments
accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230724110204.46285-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Let the krealloc_array() copy the original data and
check for a multiplication overflow.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230724110204.46285-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use sysfs_match_string() helper instead of open coded variant.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230724110204.46285-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace device_get_match_data() and i2c_match_id() by i2c_get_match
_data() as we have similar I2C and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230725171624.331283-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The .driver_data in adxl313_i2c_id[] for adxl312 and adxl314 is
wrong. Fix this issue by adding corresponding adxl31x_chip_info
data.
Reported-by: Jonathan Cameron <jic23@kernel.org>
Closes: https://lore.kernel.org/all/20230722172832.04ad7738@jic23-huawei
Fixes: a7a1c60bc4c9 ("drivers: iio: accel: adxl312 and adxl314 support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230725171624.331283-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There is no need to call the dev_err() function directly to print a custom
message when handling an error from either the platform_get_irq() or
platform_get_irq_byname() functions as both are going to display an
appropriate error message in case of a failure.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230727073912.4178659-1-ruanjinjie@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230714174628.4057920-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
adis16477 devices support burst32 function, thus has_burst32
flag should be set to true.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230719123152.309624-3-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove unused enum elements ADIS16475_SCAN_DIAG_S_FLAGS and
ADIS16475_SCAN_CRC_FAILURE.
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230719123152.309624-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Murata IRS-D200 is a PIR sensor for human detection. It has support for
raw data measurements and detection event notification.
Add a driver with support for triggered buffer and events. Map the
various settings to the `iio` framework, e.g. threshold values, sampling
frequency, filter frequencies etc.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/d218a1bc75402b5ebd6e12a563f7315f83fe966c.1689753076.git.waqar.hameed@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There are devices (such as Murata IRS-D200 PIR proximity sensor) that
check the data signal with a running period. I.e. for a specified time,
they count the number of conditions that have occurred, and then signal
if that is more than a specified amount.
`IIO_EV_INFO_PERIOD` resets when the condition no longer is true and is
therefore not suitable for these devices. Add a new `iio_event_info`
`IIO_EV_INFO_RUNNING_PERIOD` that can be used as a running period. Also
add a new `IIO_EV_INFO_RUNNING_COUNT` that can be used to specify the
number of conditions that must occur during this running period.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/ee4a801ae9b9c4716c7bd23d8f79f232351df8bd.1689753076.git.waqar.hameed@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Murata IRS-D200 is a PIR sensor for human detection. It uses the I2C bus
for communication with interrupt support. Add devicetree bindings
requiring the compatible string, I2C slave address (reg), power supply
and interrupts.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/09975910ea638a9aa893411124bbd2a5c98e45c3.1689753076.git.waqar.hameed@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This change adds support for the HMC792A Digital Attenuator. The
HMC792A is a broadband 6-bit GaAs MMIC Digital Attenuator operating
from DC to 6.0 GHz with 15.75 dB attenuation control range in 0.25 dB steps.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/hmc792a.pdf
Signed-off-by: Kim Seer Paller <kimseer.paller@analog.com>
Link: https://lore.kernel.org/r/20230721121038.183404-1-kimseer.paller@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Improve an indentation in a few places to increase readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In the snippets like the following
if (...)
return / goto / break / continue ...;
else
...
the 'else' is redundant. Get rid of it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
min() has strict type checking and preferred over min_t() for
unsigned types to avoid overflow. Here it's unclear why min_t()
was chosen since both variables are of the same type. In any
case update to use min().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230721170022.3461-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Define and init voltage configuration bits. Those bits are inited in
vendor boot code (bl2, bl33) already so do it in the driver to not depend
on other code.
Introduced bits:
REG11[0] - selects Vref. 0 - calibration voltage, 1 - VDDA. txlx and later
SoCs support VDDA or calibration voltage as Vref, but others
support only calibration voltage. For newer platforms vendor
uses VDDA as default.
REG11[1] - reserved bit. g12a and later SoCs must write 1, others SoCs
write 0.
REG11[5] - Vref voltage. 0 - 0.9v, 1 - 1.8v. g12a and later SoCs must
write 0, others SoCs write 1.
REG11[6] - selects common-mode voltage, 0: from AVDD, 1: from Vref.
g12a and later SoCs must write 0, others SoCs write 1.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Disable internal continuous ring counter at init stage. Disable value
depends on SoC family: gxl and later SoCs write 1, others write 0.
This bit are inited in vendor boot code (bl2, bl33) already so do it
in the driver to not depend on other code.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-3-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Set up input channels 0,1 muxes in the same way as for the channels 2-7
later in the code.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-2-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Simplify the probe() by replacing of_device_get_match_data() and
i2c_match_id() by i2c_get_match_data() as we have similar I2C
and DT-based matching table.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Puranjay Mohan <puranjay12@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230716175218.130557-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add IIO channel for all muxed inputs of channel 7.
Meson saradc channel 7 is connected to a mux that can switch input
to well-known sources like Vdd, GND and several Vdd dividers.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-7-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add channel labels to provide human-readable names for the inputs.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-6-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Channels could be referenced in the driver code and using enum allows
to make it more robust.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-5-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
meson_sar_adc_set_chan7_mux is a basic func() for writing single register,
defined as static. Moved it up so it could be used in more places.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Allow to use enum items for variables initialization.
For this, move enums upper in the code.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-3-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove IIO_CHAN_SOFT_TIMESTAMP channel because it's used only for
buffering mode which is not implemented.
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230714114010.293440-2-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch adds pressure compensation to the scd4x driver. The pressure can
be written to the sensor in hPa. The pressure will be compensated
internally by the sensor.
Signed-off-by: Roan van Dijk <roan@protonic.nl>
Link: https://lore.kernel.org/r/20230711101419.2065107-1-roan@protonic.nl
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In `iio_trigger_detach_poll_func()` the return value from
`trig->ops->set_trigger_state(trig, false)` is checked with `if (ret)`.
However, in `iio_trigger_attach_poll_func()` it is checked with
`if (ret < 0)`. Resolve this mismatch by only checking for `if (ret)` in
both places.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/pndv8eojdey.fsf@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Each of qcom,spmi-adc7-pm*.h headers define a set of ADC channels that
can be used for monitoring on thie particular chip. Switch them to use
channel IDs defined in the dt-bindings/iio/qcom,spmi-vadc.h header
instead of specifying the numeric IDs.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230707123027.1510723-2-dmitry.baryshkov@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Enable buffered reading of samples from the LMP92064 ADC.
The main benefit of this change is being able to read out current and
voltage measurements in a single transfer, allowing instantaneous power
measurements.
Reads into the buffer can be triggered by any software triggers, e.g.
the iio-trig-hrtimer:
$ mkdir /sys/kernel/config/iio/triggers/hrtimer/my-trigger
$ cat /sys/bus/iio/devices/iio\:device3/name
lmp92064
$ iio_readdev -t my-trigger -b 16 iio:device3 | hexdump
WARNING: High-speed mode not enabled
0000000 0000 0176 0101 0001 5507 abd5 7645 1768
0000010 0000 016d 0101 0001 ee1e ac6b 7645 1768
...
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230707063635.1496437-1-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230704095808.33780-1-frank.li@vivo.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Even though it existed in bindings for the longest time,
ADC5_GPIO2_100K_PU was never assigned in the driver. Do so.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230627-topic-adc-v1-1-c61581abffa3@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.
This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Datarate (dr) is a 3-bit wide register field. Values from 0 to 7 are
allowed for all devices but only for the ADS1115 devices a value of 7
does make a difference.
While on it fix the description of the datarate for ADS1115 devices as
well.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230621160857.3400747-1-m.felsch@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace scnprintf with sysfs_emit_at which is the preferred alternative.
Also make sure each fractional digit is in its place by padding with
zeros up to 3 digits: "...%03d...".
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230620163135.93780-1-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Allwinner's D1/T113s/R329/T507 SoCs have a new general purpose ADC.
This ADC is the same for all of this SoCs. The only difference is
the number of available channels.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-4-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.
Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:
T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch adds SoCs names to Allwinner GPADC description to
make it more informative.
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-2-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The calibration bias is setting the LED current to change the detection
distance. Add read/write attribute for proximity calibration bias and
read attribute for available values. This is supported for vcnl4040 and
vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-9-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.
Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support to configure ambient light sensor interrupts and threshold
limits for vcnl4040 and vcnl4200. If an interrupt is detected an event
will be pushed to the event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-6-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add illuminance integration time for vcnl4040 and vcnl4200.
Add read/write attribute for illuminance integration time and read
attribute for available integration times.
Set scale and sampling rate according to the integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-5-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Check IIO_PROXIMITY with switch case in order to make it easier
to add further types like light.
Add check for IIO_EV_INFO_VALUE for writing rising or falling events.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-4-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add ps_it attributes for vcnl4200 (similar to vcnl4040).
Add read/write attribute for proximity integration time.
Read attribute for available proximity integration times.
Change sampling rate depending on integration time.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-3-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add proximity interrupt support for vcnl4200 (similar to vcnl4040).
Add support to configure proximity sensor interrupts and threshold
limits. If an interrupt is detected an event will be pushed to the
event interface.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-2-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The DA217 accelerometer is another DA280 compatible accelerometer,
add its device-ids to the da280 driver.
Reported-by: Juno Computers USA <usa@junocomputers.com>
Tested-by: Juno Computers USA <usa@junocomputers.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20230613094346.162551-1-hdegoede@redhat.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Replace timestamping by the new common inv_sensors timestamp
module. The principle behind is the same but the implementation in
the new module is far better providing less jitter and a better
estimation.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-5-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Rename common module to inv_sensors_timestamp, add configuration
at init (chip internal clock, acceptable jitter, ...) and update
inv_icm42600 driver integration.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-4-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Create new inv_sensors common modules and move inv_icm42600
timestamp module inside. This module will be used by IMUs and
also in the future by other chips.
Modify inv_icm42600 driver to use timestamp module and do some
headers cleanup.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-3-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move icm42600 dependent function inside the core module.
Do some headers cleanup at the same time.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230606162147.79667-2-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Print read and expected device ID as debug warning.
Add error check for ad_sd_init() result.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Signed-off-by: Markus Burri <markus.burri@mt.com>
Link: https://lore.kernel.org/r/20230614073033.2497318-1-markus.burri@mt.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
If st->mclk is not NULL, then st->clock_sel is either AD7192_CLK_EXT_MCLK2
or AD7192_CLK_EXT_MCLK1_2.
So devm_clk_get_optional_enabled() can be used instead of hand writing it.
This saves some line of code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/7dbe973905f1fdae5d2f5ae5a3b01dd1d6a9925b.1686774340.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Reference iio.yaml schema from dtschema to allow already used
label property:
sc7180-trogdor-pazquel360-lte.dtb: proximity@28: 'label' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230617103658.114453-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Reference iio.yaml schema from dtschema to allow already used
label property:
sc7180-trogdor-homestar-r4.dtb: proximity@28: 'label' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230617103658.114453-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
|
|
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc8487b ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq update from Borislav Petkov:
- Optimize IRQ domain's name assignment
* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Use return value of strreplace()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fpu fix from Borislav Petkov:
- Do FPU AP initialization on Xen PV too which got missed by the recent
boot reordering work
* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Fix secondary processors' FPU initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for the mechanism to park CPUs with an INIT IPI.
On shutdown or kexec, the kernel tries to park the non-boot CPUs with
an INIT IPI. But the same code path is also used by the crash utility.
If the CPU which panics is not the boot CPU then it sends an INIT IPI
to the boot CPU which resets the machine.
Prevent this by validating that the CPU which runs the stop mechanism
is the boot CPU. If not, leave the other CPUs in HLT"
* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/smp: Don't send INIT to boot CPU
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Thomas Bogendoerfer:
- fixes for KVM
- fix for loongson build and cpu probing
- DT fixes
* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
MIPS: dts: add missing space before {
MIPS: Loongson: Fix build error when make modules_install
MIPS: KVM: Fix NULL pointer dereference
MIPS: Loongson: Fix cpu_probe_loongson() again
|
|
Pull xfs fix from Darrick Wong:
"Nothing exciting here, just getting rid of a gcc warning that I got
tired of seeing when I turn on gcov"
* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix uninit warning in xfs_growfs_data
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull more smb client updates from Steve French:
- fix potential use after free in unmount
- minor cleanup
- add worker to cleanup stale directory leases
* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Add a laundromat thread for cached directories
smb: client: remove redundant pointer 'server'
cifs: fix session state transition to avoid use-after-free issue
|
|
Pull NTB updates from Jon Mason:
"Fixes for pci_clean_master, error handling in driver inits, and
various other issues/bugs"
* tag 'ntb-6.5' of https://github.com/jonmason/ntb:
ntb: hw: amd: Fix debugfs_create_dir error checking
ntb.rst: Fix copy and paste error
ntb_netdev: Fix module_init problem
ntb: intel: Remove redundant pci_clear_master
ntb: epf: Remove redundant pci_clear_master
ntb_hw_amd: Remove redundant pci_clear_master
ntb: idt: drop redundant pci_enable_pcie_error_reporting()
MAINTAINERS: git://github -> https://github.com for jonmason
NTB: EPF: fix possible memory leak in pci_vntb_probe()
NTB: ntb_tool: Add check for devm_kcalloc
NTB: ntb_transport: fix possible memory leak while device_register() fails
ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
ntb: idt: Fix error handling in idt_pci_driver_init()
|
|
Lockdep is certainly right to complain about
(&vma->vm_lock->lock){++++}-{3:3}, at: vma_start_write+0x2d/0x3f
but task is already holding lock:
(&mapping->i_mmap_rwsem){+.+.}-{3:3}, at: mmap_region+0x4dc/0x6db
Invert those to the usual ordering.
Fixes: 33313a747e81 ("mm: lock newly mapped VMA which can be modified after it becomes visible")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull hotfixes from Andrew Morton:
"16 hotfixes. Six are cc:stable and the remainder address post-6.4
issues"
The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since
it was all hopefully fixed in mainline.
* tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib: dhry: fix sleeping allocations inside non-preemptable section
kasan, slub: fix HW_TAGS zeroing with slub_debug
kasan: fix type cast in memory_is_poisoned_n
mailmap: add entries for Heiko Stuebner
mailmap: update manpage link
bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
MAINTAINERS: add linux-next info
mailmap: add Markus Schneider-Pargmann
writeback: account the number of pages written back
mm: call arch_swap_restore() from do_swap_page()
squashfs: fix cache race with migration
mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison
docs: update ocfs2-devel mailing list address
MAINTAINERS: update ocfs2-devel mailing list address
mm: disable CONFIG_PER_VMA_LOCK until its fixed
fork: lock VMAs of the parent process when forking
|
|
When forking a child process, the parent write-protects anonymous pages
and COW-shares them with the child being forked using copy_present_pte().
We must not take any concurrent page faults on the source vma's as they
are being processed, as we expect both the vma and the pte's behind it
to be stable. For example, the anon_vma_fork() expects the parents
vma->anon_vma to not change during the vma copy.
A concurrent page fault on a page newly marked read-only by the page
copy might trigger wp_page_copy() and a anon_vma_prepare(vma) on the
source vma, defeating the anon_vma_clone() that wasn't done because the
parent vma originally didn't have an anon_vma, but we now might end up
copying a pte entry for a page that has one.
Before the per-vma lock based changes, the mmap_lock guaranteed
exclusion with concurrent page faults. But now we need to do a
vma_start_write() to make sure no concurrent faults happen on this vma
while it is being processed.
This fix can potentially regress some fork-heavy workloads. Kernel
build time did not show noticeable regression on a 56-core machine while
a stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~5% regression. If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance. Further
optimizations are possible if this regression proves to be problematic.
Suggested-by: David Hildenbrand <david@redhat.com>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/
Reported-by: Jacob Young <jacobly.alt@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217624
Fixes: 0bff0aaea03e ("x86/mm: try VMA lock-based page fault handling first")
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mmap_region adds a newly created VMA into VMA tree and might modify it
afterwards before dropping the mmap_lock. This poses a problem for page
faults handled under per-VMA locks because they don't take the mmap_lock
and can stumble on this VMA while it's still being modified. Currently
this does not pose a problem since post-addition modifications are done
only for file-backed VMAs, which are not handled under per-VMA lock.
However, once support for handling file-backed page faults with per-VMA
locks is added, this will become a race.
Fix this by write-locking the VMA before inserting it into the VMA tree.
Other places where a new VMA is added into VMA tree do not modify it
after the insertion, so do not need the same locking.
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With recent changes necessitating mmap_lock to be held for write while
expanding a stack, per-VMA locks should follow the same rules and be
write-locked to prevent page faults into the VMA being expanded. Add
the necessary locking.
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more SCSI updates from James Bottomley:
"A few late arriving patches that missed the initial pull request. It's
mostly bug fixes (the dt-bindings is a fix for the initial pull)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Remove unused function declaration
scsi: target: docs: Remove tcm_mod_builder.py
scsi: target: iblock: Quiet bool conversion warning with pr_preempt use
scsi: dt-bindings: ufs: qcom: Fix ICE phandle
scsi: core: Simplify scsi_cdl_check_cmd()
scsi: isci: Fix comment typo
scsi: smartpqi: Replace one-element arrays with flexible-array members
scsi: target: tcmu: Replace strlcpy() with strscpy()
scsi: ncr53c8xx: Replace strlcpy() with strscpy()
scsi: lpfc: Fix lpfc_name struct packing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
- xiic patch should have been in the original pull but slipped through
- mpc patch fixes a build regression
- nomadik cleanup
* tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mpc: Drop unused variable
i2c: nomadik: Remove a useless call in the remove function
i2c: xiic: Don't try to handle more interrupt events after error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening fixes from Kees Cook:
- Check for NULL bdev in LoadPin (Matthias Kaehlcke)
- Revert unwanted KUnit FORTIFY build default
- Fix 1-element array causing boot warnings with xhci-hub
* tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
usb: ch9: Replace bmSublinkSpeedAttr 1-element array with flexible array
Revert "fortify: Allow KUnit test to build without FORTIFY"
dm: verity-loadpin: Add NULL pointer check for 'bdev' parameter
|
|
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next
Pull more perf tools updates from Namhyung Kim:
"These are remaining changes and fixes for this cycle.
Build:
- Allow generating vmlinux.h from BTF using `make GEN_VMLINUX_H=1`
and skip if the vmlinux has no BTF.
- Replace deprecated clang -target xxx option by --target=xxx.
perf record:
- Print event attributes with well known type and config symbols in
the debug output like below:
# perf record -e cycles,cpu-clock -C0 -vv true
<SNIP>
------------------------------------------------------------
perf_event_attr:
type 0 (PERF_TYPE_HARDWARE)
size 136
config 0 (PERF_COUNT_HW_CPU_CYCLES)
{ sample_period, sample_freq } 4000
sample_type IP|TID|TIME|CPU|PERIOD|IDENTIFIER
read_format ID
disabled 1
inherit 1
freq 1
sample_id_all 1
exclude_guest 1
------------------------------------------------------------
sys_perf_event_open: pid -1 cpu 0 group_fd -1 flags 0x8 = 5
------------------------------------------------------------
perf_event_attr:
type 1 (PERF_TYPE_SOFTWARE)
size 136
config 0 (PERF_COUNT_SW_CPU_CLOCK)
{ sample_period, sample_freq } 4000
sample_type IP|TID|TIME|CPU|PERIOD|IDENTIFIER
read_format ID
disabled 1
inherit 1
freq 1
sample_id_all 1
exclude_guest 1
- Update AMD IBS event error message since it now support per-process
profiling but no priviledge filters.
$ sudo perf record -e ibs_op//k -C 0
Error:
AMD IBS doesn't support privilege filtering. Try again without
the privilege modifiers (like 'k') at the end.
perf lock contention:
- Support CSV style output using -x option
$ sudo perf lock con -ab -x, sleep 1
# output: contended, total wait, max wait, avg wait, type, caller
19, 194232, 21415, 10222, spinlock, process_one_work+0x1f0
15, 162748, 23843, 10849, rwsem:R, do_user_addr_fault+0x40e
4, 86740, 23415, 21685, rwlock:R, ep_poll_callback+0x2d
1, 84281, 84281, 84281, mutex, iwl_mvm_async_handlers_wk+0x135
8, 67608, 27404, 8451, spinlock, __queue_work+0x174
3, 58616, 31125, 19538, rwsem:W, do_mprotect_pkey+0xff
3, 52953, 21172, 17651, rwlock:W, do_epoll_wait+0x248
2, 30324, 19704, 15162, rwsem:R, do_madvise+0x3ad
1, 24619, 24619, 24619, spinlock, rcu_core+0xd4
- Add --output option to save the data to a file not to be interfered
by other debug messages.
Test:
- Fix event parsing test on ARM where there's no raw PMU nor supports
PERF_PMU_CAP_EXTENDED_HW_TYPE.
- Update the lock contention test case for CSV output.
- Fix a segfault in the daemon command test.
Vendor events (JSON):
- Add has_event() to check if the given event is available on system
at runtime. On Intel machines, some transaction events may not be
present when TSC extensions are disabled.
- Update Intel event metrics.
Misc:
- Sort symbols by name using an external array of pointers instead of
a rbtree node in the symbol. This will save 16-bytes or 24-bytes
per symbol whether the sorting is actually requested or not.
- Fix unwinding DWARF callstacks using libdw when --symfs option is
used"
* tag 'perf-tools-for-v6.5-2-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next: (38 commits)
perf test: Fix event parsing test when PERF_PMU_CAP_EXTENDED_HW_TYPE isn't supported.
perf test: Fix event parsing test on Arm
perf evsel amd: Fix IBS error message
perf: unwind: Fix symfs with libdw
perf symbol: Fix uninitialized return value in symbols__find_by_name()
perf test: Test perf lock contention CSV output
perf lock contention: Add --output option
perf lock contention: Add -x option for CSV style output
perf lock: Remove stale comments
perf vendor events intel: Update tigerlake to 1.13
perf vendor events intel: Update skylakex to 1.31
perf vendor events intel: Update skylake to 57
perf vendor events intel: Update sapphirerapids to 1.14
perf vendor events intel: Update icelakex to 1.21
perf vendor events intel: Update icelake to 1.19
perf vendor events intel: Update cascadelakex to 1.19
perf vendor events intel: Update meteorlake to 1.03
perf vendor events intel: Add rocketlake events/metrics
perf vendor metrics intel: Make transaction metrics conditional
perf jevents: Support for has_event function
...
|
|
Pull bitmap updates from Yury Norov:
"Fixes for different bitmap pieces:
- lib/test_bitmap: increment failure counter properly
The tests that don't use expect_eq() macro to determine that a test
is failured must increment failed_tests explicitly.
- lib/bitmap: drop optimization of bitmap_{from,to}_arr64
bitmap_{from,to}_arr64() optimization is overly optimistic
on 32-bit LE architectures when it's wired to
bitmap_copy_clear_tail().
- nodemask: Drop duplicate check in for_each_node_mask()
As the return value type of first_node() became unsigned, the node
>= 0 became unnecessary.
- cpumask: fix function description kernel-doc notation
- MAINTAINERS: Add bits.h and bitfield.h to the BITMAP API record
Add linux/bits.h and linux/bitfield.h for visibility"
* tag 'bitmap-6.5-rc1' of https://github.com/norov/linux:
MAINTAINERS: Add bitfield.h to the BITMAP API record
MAINTAINERS: Add bits.h to the BITMAP API record
cpumask: fix function description kernel-doc notation
nodemask: Drop duplicate check in for_each_node_mask()
lib/bitmap: drop optimization of bitmap_{from,to}_arr64
lib/test_bitmap: increment failure counter properly
|
|
The Smatch static checker reports the following warnings:
lib/dhry_run.c:38 dhry_benchmark() warn: sleeping in atomic context
lib/dhry_run.c:43 dhry_benchmark() warn: sleeping in atomic context
Indeed, dhry() does sleeping allocations inside the non-preemptable
section delimited by get_cpu()/put_cpu().
Fix this by using atomic allocations instead.
Add error handling, as atomic these allocations may fail.
Link: https://lkml.kernel.org/r/bac6d517818a7cd8efe217c1ad649fffab9cc371.1688568764.git.geert+renesas@glider.be
Fixes: 13684e966d46283e ("lib: dhry: fix unstable smp_processor_id(_) usage")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/0469eb3a-02eb-4b41-b189-de20b931fa56@moroto.mountain
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Commit 946fa0dbf2d8 ("mm/slub: extend redzone check to extra allocated
kmalloc space than requested") added precise kmalloc redzone poisoning to
the slub_debug functionality.
However, this commit didn't account for HW_TAGS KASAN fully initializing
the object via its built-in memory initialization feature. Even though
HW_TAGS KASAN memory initialization contains special memory initialization
handling for when slub_debug is enabled, it does not account for in-object
slub_debug redzones. As a result, HW_TAGS KASAN can overwrite these
redzones and cause false-positive slub_debug reports.
To fix the issue, avoid HW_TAGS KASAN memory initialization when
slub_debug is enabled altogether. Implement this by moving the
__slub_debug_enabled check to slab_post_alloc_hook. Common slab code
seems like a more appropriate place for a slub_debug check anyway.
Link: https://lkml.kernel.org/r/678ac92ab790dba9198f9ca14f405651b97c8502.1688561016.git.andreyknvl@google.com
Fixes: 946fa0dbf2d8 ("mm/slub: extend redzone check to extra allocated kmalloc space than requested")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Marco Elver <elver@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: kasan-dev@googlegroups.com
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Commit bb6e04a173f0 ("kasan: use internal prototypes matching gcc-13
builtins") introduced a bug into the memory_is_poisoned_n implementation:
it effectively removed the cast to a signed integer type after applying
KASAN_GRANULE_MASK.
As a result, KASAN started failing to properly check memset, memcpy, and
other similar functions.
Fix the bug by adding the cast back (through an additional signed integer
variable to make the code more readable).
Link: https://lkml.kernel.org/r/8c9e0251c2b8b81016255709d4ec42942dcaf018.1688431866.git.andreyknvl@google.com
Fixes: bb6e04a173f0 ("kasan: use internal prototypes matching gcc-13 builtins")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Marco Elver <elver@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
I am going to lose my vrull.eu address at the end of july, and while
adding it to mailmap I also realised that there are more old addresses
from me dangling, so update .mailmap for all of them.
Link: https://lkml.kernel.org/r/20230704163919.1136784-3-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "Update .mailmap for my work address and fix manpage".
While updating mailmap for the going-away address, I also found that on
current systems the manpage linked from the header comment changed.
And in fact it looks like the git mailmap feature got its own manpage.
This patch (of 2):
On recent systems the git-shortlog manpage only tells people to
See gitmailmap(5)
So instead of sending people on a scavenger hunt, put that info into the
header directly. Though keep the old reference around for older systems.
Link: https://lkml.kernel.org/r/20230704163919.1136784-1-heiko@sntech.de
Link: https://lkml.kernel.org/r/20230704163919.1136784-2-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
commit dd0ff4d12dd2 ("bootmem: remove the vmemmap pages from kmemleak in
put_page_bootmem") fix an overlaps existing problem of kmemleak. But the
problem still existed when HAVE_BOOTMEM_INFO_NODE is disabled, because in
this case, free_bootmem_page() will call free_reserved_page() directly.
Fix the problem by adding kmemleak_free_part() in free_bootmem_page() when
HAVE_BOOTMEM_INFO_NODE is disabled.
Link: https://lkml.kernel.org/r/20230704101942.2819426-1-liushixin2@huawei.com
Fixes: f41f2ed43ca5 ("mm: hugetlb: free the vmemmap pages associated with each HugeTLB page")
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Acked-by: Muchun Song <songmuchun@bytedance.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add linux-next info to MAINTAINERS for ease of finding this data.
Link: https://lkml.kernel.org/r/20230704054410.12527-1-rdunlap@infradead.org
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add my old mail address and update my name.
Link: https://lkml.kernel.org/r/20230628081341.3470229-1-msp@baylibre.com
Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
nr_to_write is a count of pages, so we need to decrease it by the number
of pages in the folio we just wrote, not by 1. Most callers specify
either LONG_MAX or 1, so are unaffected, but writeback_sb_inodes() might
end up writing 512x as many pages as it asked for.
Dave added:
: XFS is the only filesystem this would affect, right? AFAIA, nothing
: else enables large folios and uses writeback through
: write_cache_pages() at this point...
:
: In which case, I'd be surprised if much difference, if any, gets
: noticed by anyone.
Link: https://lkml.kernel.org/r/20230628185548.981888-1-willy@infradead.org
Fixes: 793917d997df ("mm/readahead: Add large folio readahead")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Commit c145e0b47c77 ("mm: streamline COW logic in do_swap_page()") moved
the call to swap_free() before the call to set_pte_at(), which meant that
the MTE tags could end up being freed before set_pte_at() had a chance to
restore them. Fix it by adding a call to the arch_swap_restore() hook
before the call to swap_free().
Link: https://lkml.kernel.org/r/20230523004312.1807357-2-pcc@google.com
Link: https://linux-review.googlesource.com/id/I6470efa669e8bd2f841049b8c61020c510678965
Fixes: c145e0b47c77 ("mm: streamline COW logic in do_swap_page()")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reported-by: Qun-wei Lin <Qun-wei.Lin@mediatek.com>
Closes: https://lore.kernel.org/all/5050805753ac469e8d727c797c2218a9d780d434.camel@mediatek.com/
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org> [6.1+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Migration replaces the page in the mapping before copying the contents and
the flags over from the old page, so check that the page in the page cache
is really up to date before using it. Without this, stressing squashfs
reads with parallel compaction sometimes results in squashfs reporting
data corruption.
Link: https://lkml.kernel.org/r/20230629-squashfs-cache-migration-v1-1-d50ebe55099d@axis.com
Fixes: e994f5b677ee ("squashfs: cache partial compressed blocks")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Phillip Lougher <phillip@squashfs.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The following crash happens for me when running the -mm selftests (below).
Specifically, it happens while running the uffd-stress subtests:
kernel BUG at mm/hugetlb.c:7249!
invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
CPU: 0 PID: 3238 Comm: uffd-stress Not tainted 6.4.0-hubbard-github+ #109
Hardware name: ASUS X299-A/PRIME X299-A, BIOS 1503 08/03/2018
RIP: 0010:huge_pte_alloc+0x12c/0x1a0
...
Call Trace:
<TASK>
? __die_body+0x63/0xb0
? die+0x9f/0xc0
? do_trap+0xab/0x180
? huge_pte_alloc+0x12c/0x1a0
? do_error_trap+0xc6/0x110
? huge_pte_alloc+0x12c/0x1a0
? handle_invalid_op+0x2c/0x40
? huge_pte_alloc+0x12c/0x1a0
? exc_invalid_op+0x33/0x50
? asm_exc_invalid_op+0x16/0x20
? __pfx_put_prev_task_idle+0x10/0x10
? huge_pte_alloc+0x12c/0x1a0
hugetlb_fault+0x1a3/0x1120
? finish_task_switch+0xb3/0x2a0
? lock_is_held_type+0xdb/0x150
handle_mm_fault+0xb8a/0xd40
? find_vma+0x5d/0xa0
do_user_addr_fault+0x257/0x5d0
exc_page_fault+0x7b/0x1f0
asm_exc_page_fault+0x22/0x30
That happens because a BUG() statement in huge_pte_alloc() attempts to
check that a pte, if present, is a hugetlb pte, but it does so in a
non-lockless-safe manner that leads to a false BUG() report.
We got here due to a couple of bugs, each of which by itself was not quite
enough to cause a problem:
First of all, before commit c33c794828f2("mm: ptep_get() conversion"), the
BUG() statement in huge_pte_alloc() was itself fragile: it relied upon
compiler behavior to only read the pte once, despite using it twice in the
same conditional.
Next, commit c33c794828f2 ("mm: ptep_get() conversion") broke that
delicate situation, by causing all direct pte reads to be done via
READ_ONCE(). And so READ_ONCE() got called twice within the same BUG()
conditional, leading to comparing (potentially, occasionally) different
versions of the pte, and thus to false BUG() reports.
Fix this by taking a single snapshot of the pte before using it in the
BUG conditional.
Now, that commit is only partially to blame here but, people doing
bisections will invariably land there, so this will help them find a fix
for a real crash. And also, the previous behavior was unlikely to ever
expose this bug--it was fragile, yet not actually broken.
So that's why I chose this commit for the Fixes tag, rather than the
commit that created the original BUG() statement.
Link: https://lkml.kernel.org/r/20230701010442.2041858-1-jhubbard@nvidia.com
Fixes: c33c794828f2 ("mm: ptep_get() conversion")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: James Houghton <jthoughton@google.com>
Acked-by: Muchun Song <songmuchun@bytedance.com>
Reviewed-by: Ryan Roberts <ryan.roberts@arm.com>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mike Rapoport (IBM) <rppt@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Naoya Horiguchi <naoya.horiguchi@nec.com>
Cc: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: SeongJae Park <sj@kernel.org>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: Uladzislau Rezki (Sony) <urezki@gmail.com>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The ocfs2-devel mailing list has been migrated to the kernel.org
infrastructure, update all related documentation pointers to reflect the
change.
Link: https://lkml.kernel.org/r/20230628013437.47030-3-ailiop@suse.com
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Acked-by: Joseph Qi <jiangqi903@gmail.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mark@fasheh.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The ocfs2-devel mailing list has been migrated to the kernel.org
infrastructure, update the related entry to reflect the change.
Link: https://lkml.kernel.org/r/20230628013437.47030-2-ailiop@suse.com
Signed-off-by: Anthony Iliopoulos <ailiop@suse.com>
Acked-by: Joseph Qi <jiangqi903@gmail.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
A memory corruption was reported in [1] with bisection pointing to the
patch [2] enabling per-VMA locks for x86. Disable per-VMA locks config to
prevent this issue until the fix is confirmed. This is expected to be a
temporary measure.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=217624
[2] https://lore.kernel.org/all/20230227173632.3292573-30-surenb@google.com
Link: https://lkml.kernel.org/r/20230706011400.2949242-3-surenb@google.com
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/
Reported-by: Jacob Young <jacobly.alt@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217624
Fixes: 0bff0aaea03e ("x86/mm: try VMA lock-based page fault handling first")
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Patch series "Avoid memory corruption caused by per-VMA locks", v4.
A memory corruption was reported in [1] with bisection pointing to the
patch [2] enabling per-VMA locks for x86. Based on the reproducer
provided in [1] we suspect this is caused by the lack of VMA locking while
forking a child process.
Patch 1/2 in the series implements proper VMA locking during fork. I
tested the fix locally using the reproducer and was unable to reproduce
the memory corruption problem.
This fix can potentially regress some fork-heavy workloads. Kernel build
time did not show noticeable regression on a 56-core machine while a
stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~7% regression. If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance. Further
optimizations are possible if this regression proves to be problematic.
Patch 2/2 disables per-VMA locks until the fix is tested and verified.
This patch (of 2):
When forking a child process, parent write-protects an anonymous page and
COW-shares it with the child being forked using copy_present_pte().
Parent's TLB is flushed right before we drop the parent's mmap_lock in
dup_mmap(). If we get a write-fault before that TLB flush in the parent,
and we end up replacing that anonymous page in the parent process in
do_wp_page() (because, COW-shared with the child), this might lead to some
stale writable TLB entries targeting the wrong (old) page. Similar issue
happened in the past with userfaultfd (see flush_tlb_page() call inside
do_wp_page()).
Lock VMAs of the parent process when forking a child, which prevents
concurrent page faults during fork operation and avoids this issue. This
fix can potentially regress some fork-heavy workloads. Kernel build time
did not show noticeable regression on a 56-core machine while a stress
test mapping 10000 VMAs and forking 5000 times in a tight loop shows ~7%
regression. If such fork time regression is unacceptable, disabling
CONFIG_PER_VMA_LOCK should restore its performance. Further optimizations
are possible if this regression proves to be problematic.
Link: https://lkml.kernel.org/r/20230706011400.2949242-1-surenb@google.com
Link: https://lkml.kernel.org/r/20230706011400.2949242-2-surenb@google.com
Fixes: 0bff0aaea03e ("x86/mm: try VMA lock-based page fault handling first")
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Suggested-by: David Hildenbrand <david@redhat.com>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/
Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/
Reported-by: Jacob Young <jacobly.alt@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=3D217624
Reviewed-by: Liam R. Howlett <Liam.Howlett@oracle.com>
Acked-by: David Hildenbrand <david@redhat.com>
Tested-by: Holger Hoffsttte <holger@applied-asynchrony.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
It seems the text for the NTB MSI Test Client section was copied from the
NTB Tool Test Client, but was not updated for the new section. Corrects
the NTB MSI Test Client section text.
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
With both the ntb_transport_init and the ntb_netdev_init_module routines in the
module_init init group, the ntb_netdev_init_module routine can be called before
the ntb_transport_init routine that it depends on is called. To assure the
proper initialization order put ntb_netdev_init_module in the late_initcall
group.
Fixes runtime errors where the ntb_netdev_init_module call fails with ENODEV.
Signed-off-by: Geoff Levand <geoff@infradead.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Remove pci_clear_master to simplify the code,
the bus-mastering is also cleared in do_pci_disable_device,
like this:
./drivers/pci/pci.c:2197
static void do_pci_disable_device(struct pci_dev *dev)
{
u16 pci_command;
pci_read_config_word(dev, PCI_COMMAND, &pci_command);
if (pci_command & PCI_COMMAND_MASTER) {
pci_command &= ~PCI_COMMAND_MASTER;
pci_write_config_word(dev, PCI_COMMAND, pci_command);
}
pcibios_disable_device(dev);
}.
And dev->is_busmaster is set to 0 in pci_disable_device.
Signed-off-by: Cai Huoqing <cai.huoqing@linux.dev>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f54 ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Github deprecated the git:// links about a year ago, so let's move to
the https:// URLs instead.
Reported-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://github.blog/2021-09-01-improving-git-protocol-security-github/
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
As ntb_register_device() don't handle error of device_register(),
if ntb_register_device() returns error in pci_vntb_probe(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop the
reference count that was set in device_initialize()
when it fails, so the name can be freed in kobject_cleanup().
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
As the devm_kcalloc may return NULL pointer,
it should be better to add check for the return
value, as same as the others.
Fixes: 7f46c8b3a552 ("NTB: ntb_tool: Add full multi-port NTB API support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
If device_register() returns error, the name allocated by
dev_set_name() need be freed. As comment of device_register()
says, it should use put_device() to give up the reference in
the error path. So fix this by calling put_device(), then the
name can be freed in kobject_cleanup(), and client_dev is freed
in ntb_transport_client_release().
Fixes: fce8a7bb5b4b ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
A problem about ntb_hw_intel create debugfs failed is triggered with the
following log given:
[ 273.112733] Intel(R) PCI-E Non-Transparent Bridge Driver 2.0
[ 273.115342] debugfs: Directory 'ntb_hw_intel' with parent '/' already present!
The reason is that intel_ntb_pci_driver_init() returns
pci_register_driver() directly without checking its return value, if
pci_register_driver() failed, it returns without destroy the newly created
debugfs, resulting the debugfs of ntb_hw_intel can never be created later.
intel_ntb_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: e26a5843f7f5 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
A problem about ntb_hw_amd create debugfs failed is triggered with the
following log given:
[ 618.431232] AMD(R) PCI-E Non-Transparent Bridge Driver 1.0
[ 618.433284] debugfs: Directory 'ntb_hw_amd' with parent '/' already present!
The reason is that amd_ntb_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_amd can never be created later.
amd_ntb_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: a1b3695820aa ("NTB: Add support for AMD PCI-Express Non-Transparent Bridge")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
A problem about ntb_hw_idt create debugfs failed is triggered with the
following log given:
[ 1236.637636] IDT PCI-E Non-Transparent Bridge Driver 2.0
[ 1236.639292] debugfs: Directory 'ntb_hw_idt' with parent '/' already present!
The reason is that idt_pci_driver_init() returns pci_register_driver()
directly without checking its return value, if pci_register_driver()
failed, it returns without destroy the newly created debugfs, resulting
the debugfs of ntb_hw_idt can never be created later.
idt_pci_driver_init()
debugfs_create_dir() # create debugfs directory
pci_register_driver()
driver_register()
bus_add_driver()
priv = kzalloc(...) # OOM happened
# return without destroy debugfs directory
Fix by removing debugfs when pci_register_driver() returns error.
Fixes: bf2a952d31d2 ("NTB: Add IDT 89HPESxNTx PCIe-switches support")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
|
|
Quiet down this gcc warning:
fs/xfs/xfs_fsops.c: In function ‘xfs_growfs_data’:
fs/xfs/xfs_fsops.c:219:21: error: ‘lastag_extended’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
219 | if (lastag_extended) {
| ^~~~~~~~~~~~~~~
fs/xfs/xfs_fsops.c:100:33: note: ‘lastag_extended’ was declared here
100 | bool lastag_extended;
| ^~~~~~~~~~~~~~~
By setting its value explicitly. From code analysis I don't think this
is a real problem, but I have better things to do than analyse this
closely.
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Pull mmc fix from Ulf Hansson:
- Fix regression of detection of eMMC/SD/SDIO cards
* tag 'mmc-v6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: Revert "mmc: core: Allow mmc_start_host() synchronously detect a card"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes that have been gathered recently:
- Two code-typo fixes in the new UMP core
- A fix in jack reporting to avoid the usage of mutex
- A potential data race fix in HD-audio core regmap code
- A potential data race fix in PCM allocation helper code
- HD-audio quirks for ASUS, Clevo and Unis machines
- Constifications in FireWire drivers"
* tag 'sound-fix-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirk for ASUS ROG GZ301V
ALSA: jack: Fix mutex call in snd_jack_report()
ALSA: seq: ump: fix typo in system_2p_ev_to_ump_midi1()
ALSA: hda/realtek: Whitespace fix
ALSA: hda/realtek: Add quirk for ASUS ROG G614Jx
ALSA: hda/realtek: Amend G634 quirk to enable rear speakers
ALSA: hda/realtek: Add quirk for ASUS ROG GA402X
ALSA: hda/realtek: Add quirk for ASUS ROG GX650P
ALSA: pcm: Fix potential data race at PCM memory allocation helpers
ALSA: hda: fix a possible null-pointer dereference due to data race in snd_hdac_regmap_sync()
ALSA: hda/realtek: Add quirks for Unis H3C Desktop B760 & Q760
ALSA: hda/realtek: Add quirk for Clevo NPx0SNx
ALSA: ump: Correct wrong byte size at converting a UMP System message
ALSA: fireface: make read-only const array for model names static
ALSA: oxfw: make read-only const array models static
|
|
Pull ceph updates from Ilya Dryomov:
"A bunch of CephFS fixups from Xiubo, mostly around dropping caps,
along with a fix for a regression in the readahead handling code which
sneaked in with the switch to netfs helpers"
* tag 'ceph-for-6.5-rc1' of https://github.com/ceph/ceph-client:
ceph: don't let check_caps skip sending responses for revoke msgs
ceph: issue a cap release immediately if no cap exists
ceph: trigger to flush the buffer when making snapshot
ceph: fix blindly expanding the readahead windows
ceph: add a dedicated private data for netfs rreq
ceph: voluntarily drop Xx caps for requests those touch parent mtime
ceph: try to dump the msgs when decoding fails
ceph: only send metrics when the MDS rank is ready
|
|
https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
"Updates:
- support /proc/fs/ntfs3/<dev>/volinfo and label
- alternative boot if primary boot is corrupted
- small optimizations
Fixes:
- fix endian problems
- fix logic errors
- code refactoring and reformatting"
* tag 'ntfs3_for_6.5' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: Correct mode for label entry inside /proc/fs/ntfs3/
fs/ntfs3: Add support /proc/fs/ntfs3/<dev>/volinfo and /proc/fs/ntfs3/<dev>/label
fs/ntfs3: Fix endian problem
fs/ntfs3: Add ability to format new mft records with bigger/smaller header
fs/ntfs3: Code refactoring
fs/ntfs3: Code formatting
fs/ntfs3: Do not update primary boot in ntfs_init_from_boot()
fs/ntfs3: Alternative boot if primary boot is corrupted
fs/ntfs3: Mark ntfs dirty when on-disk struct is corrupted
fs/ntfs3: Fix ntfs_atomic_open
fs/ntfs3: Correct checking while generating attr_list
fs/ntfs3: Use __GFP_NOWARN allocation at ntfs_load_attr_list()
fs: ntfs3: Fix possible null-pointer dereferences in mi_read()
fs/ntfs3: Return error for inconsistent extended attributes
fs/ntfs3: Enhance sanity check while generating attr_list
fs/ntfs3: Use wrapper i_blocksize() in ntfs_zero_range()
ntfs: Fix panic about slab-out-of-bounds caused by ntfs_listxattr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull fsnotify fix from Jan Kara:
"A fix for fanotify to disallow creating of mount or superblock marks
for kernel internal pseudo filesystems"
* tag 'fsnotify_for_v6.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
fanotify: disallow mount/sb marks on kernel internal pseudo fs
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
- A bunch of fixes/cleanups from the first part of the merge window,
mostly related to ACPI and vector as those were large
- Some documentation improvements, mostly related to the new code
- The "riscv,isa" DT key is deprecated
- Support for link-time dead code elimination
- Support for minor fault registration in userfaultd
- A handful of cleanups around CMO alternatives
* tag 'riscv-for-linus-6.5-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (23 commits)
riscv: mm: mark noncoherent_supported as __ro_after_init
riscv: mm: mark CBO relate initialization funcs as __init
riscv: errata: thead: only set cbom size & noncoherent during boot
riscv: Select HAVE_ARCH_USERFAULTFD_MINOR
RISC-V: Document the ISA string parsing rules for ACPI
risc-v: Fix order of IPI enablement vs RCU startup
mm: riscv: fix an unsafe pte read in huge_pte_alloc()
dt-bindings: riscv: deprecate riscv,isa
RISC-V: drop error print from riscv_hartid_to_cpuid()
riscv: Discard vector state on syscalls
riscv: move memblock_allow_resize() after linear mapping is ready
riscv: Enable ARCH_SUSPEND_POSSIBLE for s2idle
riscv: vdso: include vdso/vsyscall.h for vdso_data
selftests: Test RISC-V Vector's first-use handler
riscv: vector: clear V-reg in the first-use trap
riscv: vector: only enable interrupts in the first-use trap
RISC-V: Fix up some vector state related build failures
RISC-V: Document that V registers are clobbered on syscalls
riscv: disable HAVE_LD_DEAD_CODE_DATA_ELIMINATION for LLD
riscv: enable HAVE_LD_DEAD_CODE_DATA_ELIMINATION
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix PCIe MEM size for pci2 node on Turris 1.x boards
- Two minor build fixes
Thanks to Christophe Leroy, Douglas Anderson, Pali Rohár, Petr Mladek,
and Randy Dunlap.
* tag 'powerpc-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: dts: turris1x.dts: Fix PCIe MEM size for pci2 node
powerpc: Include asm/nmi.c in mobility.c for watchdog_hardlockup_set_timeout_pct()
powerpc: allow PPC_EARLY_DEBUG_CPM only when SERIAL_CPM=y
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor
Pull apparmor updates from John Johansen:
- fix missing error check for rhashtable_insert_fast
- add missing failure check in compute_xmatch_perms
- fix policy_compat permission remap with extended permissions
- fix profile verification and enable it
- fix kzalloc perms tables for shared dfas
- Fix kernel-doc header for verify_dfa_accept_index
- aa_buffer: Convert 1-element array to flexible array
- Return directly after a failed kzalloc() in two functions
- fix use of strcpy in policy_unpack_test
- fix kernel-doc complaints
- Fix some kernel-doc comments
* tag 'apparmor-pr-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/jj/linux-apparmor:
apparmor: Fix kernel-doc header for verify_dfa_accept_index
apparmor: fix: kzalloc perms tables for shared dfas
apparmor: fix profile verification and enable it
apparmor: fix policy_compat permission remap with extended permissions
apparmor: aa_buffer: Convert 1-element array to flexible array
apparmor: add missing failure check in compute_xmatch_perms
apparmor: fix missing error check for rhashtable_insert_fast
apparmor: Return directly after a failed kzalloc() in two functions
AppArmor: Fix some kernel-doc comments
apparmor: fix use of strcpy in policy_unpack_test
apparmor: fix kernel-doc complaints
|
|
Parking CPUs in INIT works well, except for the crash case when the CPU
which invokes smp_park_other_cpus_in_init() is not the boot CPU. Sending
INIT to the boot CPU resets the whole machine.
Prevent this by validating that this runs on the boot CPU. If not fall back
and let CPUs hang in HLT.
Fixes: 45e34c8af58f ("x86/smp: Put CPUs into INIT on shutdown if possible")
Reported-by: Baokun Li <libaokun1@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Baokun Li <libaokun1@huawei.com>
Link: https://lore.kernel.org/r/87ttui91jo.ffs@tglx
|
|
Commit e4de20576986 ("MIPS: KVM: Fix NULL pointer dereference") missed
converting one place accessing cop0 registers, which results in a build
error, if KVM_MIPS_DEBUG_COP0_COUNTERS is enabled.
Fixes: e4de20576986 ("MIPS: KVM: Fix NULL pointer dereference")
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
Adds the required quirk to enable the Cirrus amp and correct pins
on the ASUS ROG GZ301V series which uses an SPI connected Cirrus amp.
While this works if the related _DSD properties are made available, these
aren't included in the ACPI of these laptops (yet).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230706223323.30871-2-luke@ljones.dev
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull drm fixes from Dave Airlie:
"Lots of fixes, mostly i915 and amdgpu. It's two weeks of i915, and I
think three weeks of amdgpu.
fbdev:
- Fix module infos on sparc
panel:
- Fix mode on Starry-ili9882t
i915:
- Allow DC states along with PW2 only for PWB functionality [adlp+]
- Fix SSC selection for MPLLA [mtl]
- Use hw.adjusted mode when calculating io/fast wake times [psr]
- Apply min softlimit correctly [guc/slpc]
- Assign correct hdcp content type [hdcp]
- Add missing forward declarations/includes to display power headers
- Fix BDW PSR AUX CH data register offsets [psr]
- Use mock device info for creating mock device
amdgpu:
- Misc cleanups
- GFX 9.4.3 fixes
- DEBUGFS build fix
- Fix LPDDR5 reporting
- ASPM fixes
- DCN 3.1.4 fixes
- DP MST fixes
- DCN 3.2.x fixes
- Display PSR TCON fixes
- SMU 13.x fixes
- RAS fixes
- Vega12/20 SMU fixes
- PSP flashing cleanup
- GFX9 MCBP fixes
- SR-IOV fixes
- GPUVM clear mappings fix for always valid BOs
- Add FAMS quirk for problematic monitor
- Fix possible UAF
- Better handle monentary temperature fluctuations
- SDMA 4.4.2 fixes
- Fencing fix"
* tag 'drm-next-2023-07-07' of git://anongit.freedesktop.org/drm/drm: (83 commits)
drm/i915: use mock device info for creating mock device
drm/i915/psr: Fix BDW PSR AUX CH data register offsets
drm/amdgpu: Fix potential fence use-after-free v2
drm/amd/pm: avoid unintentional shutdown due to temperature momentary fluctuation
drm/amd/pm: expose swctf threshold setting for legacy powerplay
drm/amd/display: 3.2.241
drm/amd/display: Take full update path if number of planes changed
drm/amd/display: Create debugging mechanism for Gaming FAMS
drm/amd/display: Add monitor specific edid quirk
drm/amd/display: For new fast update path, loop through each surface
drm/amd/display: Remove Phantom Pipe Check When Calculating K1 and K2
drm/amd/display: Limit new fast update path to addr and gamma / color
drm/amd/display: Fix the delta clamping for shaper LUT
drm/amdgpu: Keep non-psp path for partition switch
drm/amd/display: program DPP shaper and 3D LUT if updated
Revert "drm/amd/display: edp do not add non-edid timings"
drm/amdgpu: share drm device for pci amdgpu device with 1st partition device
drm/amd/pm: Add GFX v9.4.3 unique id to sysfs
drm/amd/pm: Enable pp_feature attribute
drm/amdgpu/vcn: Need to unpause dpg before stop dpg
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These fix a couple of compiler warnings, refine an ACPI device
enumeration quirk to address a driver regression and clean up code.
Specifics:
- Make acpi_companion_match() return a const pointer and update its
callers accordingly (Andy Shevchenko)
- Move the extern declaration of the acpi_root variable to a header
file so as to address a compiler warning (Andy Shevchenko)
- Address compiler warnings in the ACPI device enumeration code by
adding a missing header file include to it (Ben Dooks)
- Refine the SMB0001 quirk in the ACPI device enumeration code so as
to address an i2c-scmi driver regression (Andy Shevchenko)
- Clean up two pieces of the ACPI device enumeration code (Andy
Shevchenko)"
* tag 'acpi-6.5-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: scan: Use the acpi_match_acpi_device() helper
ACPI: platform: Move SMB0001 HID to the header and reuse
ACPI: platform: Ignore SMB0001 only when it has resources
ACPI: bus: Introduce acpi_match_acpi_device() helper
ACPI: scan: fix undeclared variable warnings by including sleep.h
ACPI: bus: Constify acpi_companion_match() returned value
ACPI: scan: Move acpi_root to internal header
|
|
Pull mode documentation updates from Jonathan Corbet:
"A half-dozen late arriving docs patches. They are mostly fixes, but we
also have a kernel-doc tweak for enums and the long-overdue removal of
the outdated and redundant patch-submission comments at the top of the
MAINTAINERS file"
* tag 'docs-6.5-2' of git://git.lwn.net/linux:
scripts: kernel-doc: support private / public marking for enums
Documentation: KVM: SEV: add a missing backtick
Documentation: ACPI: fix typo in ssdt-overlays.rst
Fix documentation of panic_on_warn
docs: remove the tips on how to submit patches from MAINTAINERS
docs: fix typo in zh_TW and zh_CN translation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few mostly minor fixes that came in during the merge window, plus
one administrative update for Jonas' e-mail address.
The spi-geni-qcom fix is more major than the others, fixing the newly
added DMA support for large reads which trigger DMA"
* tag 'spi-fix-v6.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bcm{63xx,bca}-hsspi: update my email address
spi: rzv2m-csi: Fix SoC product name
spi: bcm-qspi: return error if neither hif_mspi nor mspi is available
spi: spi-geni-qcom: enable SPI_CONTROLLER_MUST_TX for GPI DMA mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A simple dependency fix for a newly added driver"
* tag 'regulator-fix-v6.5-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: raa215300: Add build dependency with COMMON_CLK
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Fix bad git merge of #endif in arm64 code
A merge of the arm64 tree caused #endif to go into the wrong place
- Fix crash on lseek of write access to tracefs/error_log
Opening error_log as write only, and then doing an lseek() causes a
kernel panic, because the lseek() handle expects a "seq_file" to
exist (which is not done on write only opens). Use tracing_lseek()
that tests for this instead of calling the default seq lseek handler.
- Check for negative instead of -E2BIG for error on strscpy() returns
Instead of testing for -E2BIG from strscpy(), to be more robust,
check for less than zero, which will make sure it catches any error
that strscpy() may someday return.
* tag 'trace-v6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/boot: Test strscpy() against less than zero for error
arm64: ftrace: fix build error with CONFIG_FUNCTION_GRAPH_TRACER=n
tracing: Fix null pointer dereference in tracing_err_log_open()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull vfs fixes from Christian Brauner:
"This contains two minor fixes for Jan's rename locking work:
- Unlocking the source inode was guarded by a check whether source
was non-NULL. This doesn't make sense because source must be
non-NULL and the commit message explains in detail why
- The lock_two_nondirectories() helper called WARN_ON_ONCE() and
dereferenced the inodes unconditionally but the underlying
lock_two_inodes() helper and the kernel documentation for that
function are clear that it is valid to pass NULL arguments, so a
non-NULL check is needed. No callers currently pass NULL arguments
but let's not knowingly leave landmines around"
* tag 'v6.5/vfs.fixes.2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
fs: don't assume arguments are non-NULL
fs: no need to check source
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* panel: Fix mode on Starry-ili9882t
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230706112203.GA30555@linux-uq9g
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Fix BDW PSR AUX CH data register offsets [psr] (Ville Syrjälä)
- Use mock device info for creating mock device (Jani Nikula)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZKZ6VIeInBYrBuph@tursulin-desk
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-fixes-6.5-2023-06-30-1:
amdgpu:
- Misc cleanups
- GFX 9.4.3 fixes
- DEBUGFS build fix
- Fix LPDDR5 reporting
- ASPM fixes
- DCN 3.1.4 fixes
- DP MST fixes
- DCN 3.2.x fixes
- Display PSR TCON fixes
- SMU 13.x fixes
- RAS fixes
- Vega12/20 SMU fixes
- PSP flashing cleanup
- GFX9 MCBP fixes
- SR-IOV fixes
- GPUVM clear mappings fix for always valid BOs
- Add FAMS quirk for problematic monitor
- Fix possible UAF
- Better handle monentary temperature fluctuations
- SDMA 4.4.2 fixes
- Fencing fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230630175757.8128-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
- Allow DC states along with PW2 only for PWB functionality [adlp+] (Imre Deak)
- Fix SSC selection for MPLLA [mtl] (Radhakrishna Sripada)
- Use hw.adjusted mode when calculating io/fast wake times [psr] (Jouni Högander)
- Apply min softlimit correctly [guc/slpc] (Vinay Belgaumkar)
- Assign correct hdcp content type [hdcp] (Suraj Kandpal)
- Add missing forward declarations/includes to display power headers (Imre Deak)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZJ1WpY+GF9NcsWXp@tursulin-desk
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Alexander Gordeev:
- Fix virtual vs physical address confusion in vmem_add_range() and
vmem_remove_range() functions
- Include <linux/io.h> instead of <asm/io.h> and <asm-generic/io.h>
throughout s390 code
- Make all PSW related defines also available for assembler files.
Remove PSW_DEFAULT_KEY define from uapi for that
- When adding an undefined symbol the build still succeeds, but
userspace crashes trying to execute VDSO, because the symbol is not
resolved. Add undefined symbols check to prevent that
- Use kvmalloc_array() instead of kzalloc() for allocaton of 256k
memory when executing s390 crypto adapter IOCTL
- Add -fPIE flag to prevent decompressor misaligned symbol build error
with clang
- Use .balign instead of .align everywhere. This is a no-op for s390,
but with this there no mix in using .align and .balign anymore
- Filter out -mno-pic-data-is-text-relative flag when compiling kernel
to prevent VDSO build error
- Rework entering of DAT-on mode on CPU restart to use PSW_KERNEL_BITS
mask directly
- Do not retry administrative requests to some s390 crypto cards, since
the firmware assumes replay attacks
- Remove most of the debug code, which is build in when kernel config
option CONFIG_ZCRYPT_DEBUG is enabled
- Remove CONFIG_ZCRYPT_MULTIDEVNODES kernel config option and switch
off the multiple devices support for the s390 zcrypt device driver
- With the conversion to generic entry machine checks are accounted to
the current context instead of irq time. As result, the STCKF
instruction at the beginning of the machine check handler and the
lowcore member are no longer required, therefore remove it
- Fix various typos found with codespell
- Minor cleanups to CPU-measurement Counter and Sampling Facilities
code
- Revert patch that removes VMEM_MAX_PHYS macro, since it causes a
regression
* tag 's390-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (25 commits)
Revert "s390/mm: get rid of VMEM_MAX_PHYS macro"
s390/cpum_sf: remove check on CPU being online
s390/cpum_sf: handle casts consistently
s390/cpum_sf: remove unnecessary debug statement
s390/cpum_sf: remove parameter in call to pr_err
s390/cpum_sf: simplify function setup_pmu_cpu
s390/cpum_cf: remove unneeded debug statements
s390/entry: remove mcck clock
s390: fix various typos
s390/zcrypt: remove ZCRYPT_MULTIDEVNODES kernel config option
s390/zcrypt: do not retry administrative requests
s390/zcrypt: cleanup some debug code
s390/entry: rework entering DAT-on mode on CPU restart
s390/mm: fence off VM macros from asm and linker
s390: include linux/io.h instead of asm/io.h
s390/ptrace: make all psw related defines also available for asm
s390/ptrace: remove PSW_DEFAULT_KEY from uapi
s390/vdso: filter out mno-pic-data-is-text-relative cflag
s390: consistently use .balign instead of .align
s390/decompressor: fix misaligned symbol build error
...
|
|
Fix the following build error.
Error log:
drivers/i2c/busses/i2c-mpc.c: In function 'mpc_i2c_setup_512x':
drivers/i2c/busses/i2c-mpc.c:310:20: error: unused variable 'pval'
Fixes: 9d178e00583e ("i2c: mpc: Use of_property_read_reg() to parse "reg"")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Since commit 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba
driver"), there is no more request_mem_region() call in this driver.
So remove the release_mem_region() call from the remove function which is
likely a left over.
Fixes: 235602146ec9 ("i2c-nomadik: turn the platform driver to an amba driver")
Cc: <stable@vger.kernel.org> # v3.6+
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
In xiic_process, it is possible that error events such as arbitration
lost or TX error can be raised in conjunction with other interrupt flags
such as TX FIFO empty or bus not busy. Error events result in the
controller being reset and the error returned to the calling request,
but the function could potentially try to keep handling the other
events, such as by writing more messages into the TX FIFO. Since the
transaction has already failed, this is not helpful and will just cause
issues.
This problem has been present ever since:
commit 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
which allowed non-error events to be handled after errors, but became
more obvious after:
commit 743e227a8959 ("i2c: xiic: Defer xiic_wakeup() and
__xiic_start_xfer() in xiic_process()")
which reworked the code to add a WARN_ON which triggers if both the
xfer_more and wakeup_req flags were set, since this combination is
not supposed to happen, but was occurring in this scenario.
Skip further interrupt handling after error flags are detected to avoid
this problem.
Fixes: 7f9906bd7f72 ("i2c: xiic: Service all interrupts in isr")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306141934.UKmM9bFX-lkp@intel.com/
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Currently the permstables of the shared dfas are not shared, and need
to be allocated and copied. In the future this should be addressed
with a larger rework on dfa and pdb ref counts and structure sharing.
BugLink: http://bugs.launchpad.net/bugs/2017903
Fixes: 217af7e2f4de ("apparmor: refactor profile rules and attachments")
Cc: stable@vger.kernel.org
Signed-off-by: John Johansen <john.johansen@canonical.com>
Reviewed-by: Jon Tourville <jontourville@me.com>
|
|
The transition table size was not being set by compat mappings
resulting in the profile verification code not being run. Unfortunately
the checks were also buggy not being correctly updated from the old
accept perms, to the new layout.
Also indicate to userspace that the kernel has the permstable verification
fixes.
BugLink: http://bugs.launchpad.net/bugs/2017903
Fixes: 670f31774ab6 ("apparmor: verify permission table indexes")
Signed-off-by: John Johansen <john.johansen@canonical.com>
Reviewed-by: Jon Tourville <jontourville@me.com>
|
|
If the extended permission table is present we should not be attempting
to do a compat_permission remap as the compat_permissions are not
stored in the dfa accept states.
Fixes: fd1b2b95a211 ("apparmor: add the ability for policy to specify a permission table")
Signed-off-by: John Johansen <john.johansen@canonical.com>
Reviewed-by: Jon Tourville <jontourville@me.com>
|
|
In the ongoing effort to convert all fake flexible arrays to proper
flexible arrays, replace aa_buffer's 1-element "buffer" member with a
flexible array.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Add check for failure to allocate the permission table.
Fixes: caa9f579ca72 ("apparmor: isolate policy backwards compatibility to its own file")
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
rhashtable_insert_fast() could return err value when memory allocation is
failed. but unpack_profile() do not check values and this always returns
success value. This patch just adds error check code.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e025be0f26d5 ("apparmor: support querying extended trusted helper extra data")
Signed-off-by: Danila Chernetsov <listdansp@mail.ru>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
1. Return directly after a call of the function “kzalloc” failed
at the beginning in these function implementations.
2. Omit extra initialisations (for a few local variables)
which became unnecessary with this refactoring.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Make the description of @table to @strs in function unpack_trans_table()
to silence the warnings:
security/apparmor/policy_unpack.c:456: warning: Function parameter or member 'strs' not described in 'unpack_trans_table'
security/apparmor/policy_unpack.c:456: warning: Excess function parameter 'table' description in 'unpack_trans_table'
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=4332
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
Replace the use of strcpy() in build_aa_ext_struct() in
policy_unpack_test.c with strscpy().
strscpy() is the safer method to use to ensure the buffer does not
overflow. This was found by kernel test robot:
https://lore.kernel.org/all/202301040348.NbfVsXO0-lkp@intel.com/.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rae Moar <rmoar@google.com>
Signed-off-by: John Johansen <john.johansen@canonical.com>
|
|
These cleanups came up as part of the discussion on the "riscv: Reduce
ARCH_KMALLOC_MINALIGN to 8" patch set, but that needs additional work
and thus will be delayed at least a cycle.
* b4-shazam-merge:
riscv: mm: mark noncoherent_supported as __ro_after_init
riscv: mm: mark CBO relate initialization funcs as __init
riscv: errata: thead: only set cbom size & noncoherent during boot
Link: https://lore.kernel.org/linux-riscv/20230526165958.908-1-jszhang@kernel.org/
Link: https://lore.kernel.org/r/20230614165504.532-1-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The noncoherent_supported indicates whether the HW is coherent or not,
it won't change after booting, mark it as __ro_after_init.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230614165504.532-4-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The two functions cbo_get_block_size() and riscv_init_cbo_blocksizes()
are only called during booting, mark them as __init.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230614165504.532-3-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The CBOM size and whether the HW is noncoherent is known and
determined during booting and won't change after that.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230614165504.532-2-jszhang@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
This allocates the VM flag needed to support the userfaultfd minor fault
functionality. Because the flag bit is >= bit 32, it can only be enabled
for 64-bit kernels. See commit 7677f7fd8be7 ("userfaultfd: add minor
fault registration mode") for more information.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Link: https://lore.kernel.org/r/20230624060321.3401504-1-samuel.holland@sifive.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
We've had a ton of issues around the ISA string parsing rules elsewhere
in RISC-V, so let's at least be clear about what the rules are so we can
try and avoid more issues.
Link: https://lore.kernel.org/r/CAK9=C2Vy-4V9kgnga98tiC3TeHkR2LFPakyBbS8s_h3_Z=ieyQ@mail.gmail.com/
Link: https://lore.kernel.org/r/20230629031705.15575-1-palmer@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Merge additional ACPI device enumeration code changes for 6.5-rc1.
- Make acpi_companion_match() return a const pointer and update its
callers accordingly (Andy Shevchenko).
- Move the extern declaration of the acpi_root variable to a header
file so as to address a compiler warning (Andy Shevchenko).
- Address compiler warnings in the ACPI device enumeration code by
adding a missing header file include to it (Ben Dooks).
- Refine the SMB0001 quirk in the ACPI device enumeration code so as to
address an i2c-scmi driver regression (Andy Shevchenko).
- Clean up two pieces of the ACPI device enumeration code (Andy
Shevchenko).
* acpi-bus:
ACPI: bus: Constify acpi_companion_match() returned value
* acpi-scan:
ACPI: scan: Use the acpi_match_acpi_device() helper
ACPI: platform: Move SMB0001 HID to the header and reuse
ACPI: platform: Ignore SMB0001 only when it has resources
ACPI: bus: Introduce acpi_match_acpi_device() helper
ACPI: scan: fix undeclared variable warnings by including sleep.h
ACPI: scan: Move acpi_root to internal header
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"These are cleanups for architecture specific header files:
- the comments in include/linux/syscalls.h have gone out of sync and
are really pointless, so these get removed
- The asm/bitsperlong.h header no longer needs to be architecture
specific on modern compilers, so use a generic version for newer
architectures that use new enough userspace compilers
- A cleanup for virt_to_pfn/virt_to_bus to have proper type checking,
forcing the use of pointers"
* tag 'asm-generic-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
syscalls: Remove file path comments from headers
tools arch: Remove uapi bitsperlong.h of hexagon and microblaze
asm-generic: Unify uapi bitsperlong.h for arm64, riscv and loongarch
m68k/mm: Make pfn accessors static inlines
arm64: memory: Make virt_to_pfn() a static inline
ARM: mm: Make virt_to_pfn() a static inline
asm-generic/page.h: Make pfn accessors static inlines
xen/netback: Pass (void *) to virt_to_page()
netfs: Pass a pointer to virt_to_page()
cifs: Pass a pointer to virt_to_page() in cifsglob
cifs: Pass a pointer to virt_to_page()
riscv: mm: init: Pass a pointer to virt_to_page()
ARC: init: Pass a pointer to virt_to_pfn() in init
m68k: Pass a pointer to virt_to_pfn() virt_to_page()
fs/proc/kcore.c: Pass a pointer to virt_addr_valid()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"There are three small fixes that came up sincie the past week:
- an incorrect bit offset in ixp4xx bus driver
- a riscv randconfig regression in the thead platform I merged
- whitespace fixes for some dts files"
* tag 'soc-fixes-6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
bus: ixp4xx: fix IXP4XX_EXP_T1_MASK
ARM: dts: st: add missing space before {
RISC-V: make ARCH_THEAD preclude XIP_KERNEL
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"New support:
- TI J721S2 CSI BCDMA support
Updates:
- Native HDMI support for dw edma driver
- ste dma40 updates for supporting proper SRAM handle in DT
- removal of dma device chancnt setting in drivers"
* tag 'dmaengine-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (28 commits)
dmaengine: sprd: Don't set chancnt
dmaengine: hidma: Don't set chancnt
dmaengine: plx_dma: Don't set chancnt
dmaengine: axi-dmac: Don't set chancnt
dmaengine: dw-axi-dmac: Don't set chancnt
dmaengine: qcom: bam_dma: allow omitting num-{channels,ees}
dmaengine: dw-edma: Add HDMA DebugFS support
dmaengine: dw-edma: Add support for native HDMA
dmaengine: dw-edma: Create a new dw_edma_core_ops structure to abstract controller operation
dmaengine: dw-edma: Rename dw_edma_core_ops structure to dw_edma_plat_ops
dmaengine: ste_dma40: use proper format string for resource_size_t
dmaengine: make QCOM_HIDMA depend on HAS_IOMEM
dmaengine: ste_dma40: fix typo in enum documentation
dmaengine: ste_dma40: use correct print specfier for resource_size_t
MAINTAINERS: Add myself as the DW eDMA driver reviewer
MAINTAINERS: Add Manivannan to DW eDMA driver maintainers list
MAINTAINERS: Demote Gustavo Pimentel to DW EDMA driver reviewer
dmaengine: ti: k3-udma: Add support for J721S2 CSI BCDMA instance
dt-bindings: dma: ti: Add J721S2 BCDMA
dmaengine: ti: k3-psil-j721s2: Add PSI-L thread map for main CPSW2G
...
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add Xilinx Versal watchdog
- support Hygon FCH/SCH (Server Controller Hub)
- convert GPL notices to SPDX identifiers
- other improvements
* tag 'linux-watchdog-6.5-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: sp5100_tco: support Hygon FCH/SCH (Server Controller Hub)
dt-bindings: watchdog: restrict node name suffixes
MAINTAINERS: Add support for Xilinx versal watchdog
watchdog: xilinx_wwdt: Add Versal window watchdog support
dt-bindings: watchdog: xlnx,versal-wwdt: Add versal watchdog
watchdog: ziirave_wdt: Switch i2c driver back to use .probe()
watchdog: ibmasr: Replace GPL license notice with SPDX identifier
watchdog: Convert GPL 2.0 notice to SPDX identifier
watchdog: loongson1_wdt: Add DT support
|
|
snd_jack_report() is supposed to be callable from an IRQ context, too,
and it's indeed used in that way from virtsnd driver. The fix for
input_dev race in commit 1b6a6fc5280e ("ALSA: jack: Access input_dev
under mutex"), however, introduced a mutex lock in snd_jack_report(),
and this resulted in a potential sleep-in-atomic.
For addressing that problem, this patch changes the relevant code to
use the object get/put and removes the mutex usage. That is,
snd_jack_report(), it takes input_get_device() and leaves with
input_put_device() for assuring the input_dev being assigned.
Although the whole mutex could be reduced, we keep it because it can
be still a protection for potential races between creation and
deletion.
Fixes: 1b6a6fc5280e ("ALSA: jack: Access input_dev under mutex")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/cf95f7fe-a748-4990-8378-000491b40329@moroto.mountain
Tested-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230706155357.3470-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* fbdev: Fix module infos on sparc
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230629113814.GA10448@linux-uq9g
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux
Pull sh updates from Adrian Glaubitz:
"Fix a compiler warning in the J2 probing code and a fix by Sergey
Shtylyov to avoid using IRQ0 on SH3 and SH4 targets. Masahiro Yamada
made some clean-up in the build system to address reports by the 0day
bot.
The most notable changes come from Artur Rojek who addressed a number
of issues in the DMA code, in particular a fix for the DMA channel
offset calculation that was introduced in in 7f47c7189b3e ("sh: dma:
More legacy cpu dma chainsawing.") in 2012!
Together with another change to correct the number of DMA channels for
each SuperH SoC according to specification, Artur's series unbreaks
the kernel on the SH7709 SoC allowing Linux to boot on the HP Jornada
680 handheld again.
Summary:
- Provide unxlate_dev_mem_ptr() in asm/io.h
- dma: Correct the number of DMA channels for SH7709
- dma: Drop incorrect SH_DMAC_BASE1 definition for SH4
- dma: Fix DMA channel offset calculation
- Remove compiler flag duplication
- Refactor header include path addition
- Move build rule for cchips/hd6446x/ to arch/sh/Kbuild
- Fix -Wmissing-include-dirs warnings for various platforms
- Avoid using IRQ0 on SH3 and SH4
- j2: Use ioremap() to translate device tree address into kernel
memory"
* tag 'sh-for-v6.5-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: Provide unxlate_dev_mem_ptr() in asm/io.h
sh: dma: Correct the number of DMA channels for SH7709
sh: dma: Drop incorrect SH_DMAC_BASE1 definition for SH4
sh: dma: Fix DMA channel offset calculation
sh: Remove compiler flag duplication
sh: Refactor header include path addition
sh: Move build rule for cchips/hd6446x/ to arch/sh/Kbuild
sh: Fix -Wmissing-include-dirs warnings for various platforms
sh: Avoid using IRQ0 on SH3 and SH4
sh: j2: Use ioremap() to translate device tree address into kernel memory
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"New Support:
- Debugfs support for phy core and mediatek driver
- Hisilicon inno-usb2-phy driver supporting Hi3798MV100
- Qualcomm SGMII SerDes PHY driver, SM6115 & QCM2290 QMP-USB support,
SA8775P USB PHY & USB3 UNI support, QUSB2 support for IPQ9574,
IPQ9574 USB3 PHY
UpdatesL
- Sparx5 serdes phy power optimzation
- cadence salvo usb properties and updates and torrent DP with PCIe &
USB support
- Yaml conversion for Broadcom kona USB bindings and MXS USB binding"
* tag 'phy-for-6.5_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (67 commits)
dt-bindings: phy: brcm,brcmstb-usb-phy: Fix error in "compatible" conditional schema
dt-bindings: phy: mixel,mipi-dsi-phy: Remove assigned-clock* properties
dt-bindings: phy: intel,combo-phy: restrict node name suffixes
dt-bindings: phy: qcom,usb-hs-phy: Add compatible
phy: tegra: xusb: check return value of devm_kzalloc()
phy: qcom: qmp-combo: fix Display Port PHY configuration for SM8550
phy: qcom: add the SGMII SerDes PHY driver
dt-bindings: phy: describe the Qualcomm SGMII PHY
phy: qualcomm: fix indentation in Makefile
phy: usb: suppress OC condition for 7439b2
phy: usb: Turn off phy when port is in suspend
phy: tegra: xusb: Clear the driver reference in usb-phy dev
dt-bindings: phy: mxs-usb-phy: add imx8ulp and imx8qm compatible
dt-bindings: phy: mxs-usb-phy: convert to DT schema format
dt-bindings: phy: qcom,qmp-usb: fix bindings error
dt-bindings: phy: qcom,qmp-ufs: fix the sc8180x regs
dt-bindings: phy: qcom,qmp-pcie: fix the sc8180x regs
phy: mediatek: tphy: add debugfs files
phy: core: add debugfs files
phy: fsl-imx8mp-usb: add support for phy tuning
...
|
|
and drop cached directories after 30 seconds
Signed-off-by: Ronnie Sahlberg <lsahlber@redhat.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this cycle, we've mainly investigated the zoned block device
support along with patches such as correcting write pointers between
f2fs and storage, adding asynchronous zone reset flow, and managing
the number of open zones.
Other than them, f2fs adds another mount option, "errors=x" to specify
how to handle when it detects an unexpected behavior at runtime.
Enhancements:
- support 'errors=remount-ro|continue|panic' mount option
- enforce some inode flag policies
- allow .tmp compression given extensions
- add some ioctls to manage the f2fs compression
- improve looped node chain flow
- avoid issuing small-sized discard commands during checkpoint
- implement an asynchronous zone reset
Bug fixes:
- fix deadlock in xattr and inode page lock
- fix and add sanity check in some error paths
- fix to avoid NULL pointer dereference f2fs_write_end_io() along
with put_super
- set proper flags to quota files
- fix potential deadlock due to unpaired node_write lock use
- fix over-estimating free section during FG GC
- fix the wrong condition to determine atomic context
As usual, also there are a number of patches with code refactoring and
minor clean-ups"
* tag 'f2fs-for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (46 commits)
f2fs: fix to do sanity check on direct node in truncate_dnode()
f2fs: only set release for file that has compressed data
f2fs: fix compile warning in f2fs_destroy_node_manager()
f2fs: fix error path handling in truncate_dnode()
f2fs: fix deadlock in i_xattr_sem and inode page lock
f2fs: remove unneeded page uptodate check/set
f2fs: update mtime and ctime in move file range method
f2fs: compress tmp files given extension
f2fs: refactor struct f2fs_attr macro
f2fs: convert to use sbi directly
f2fs: remove redundant assignment to variable err
f2fs: do not issue small discard commands during checkpoint
f2fs: check zone write pointer points to the end of zone
f2fs: add f2fs_ioc_get_compress_blocks
f2fs: cleanup MIN_INLINE_XATTR_SIZE
f2fs: add helper to check compression level
f2fs: set FMODE_CAN_ODIRECT instead of a dummy direct_IO method
f2fs: do more sanity check on inode
f2fs: compress: fix to check validity of i_compress_flag field
f2fs: add sanity compress level check for compressed file
...
|
|
Since commit 2d47c6956ab3 ("ubsan: Tighten UBSAN_BOUNDS on GCC"),
UBSAN_BOUNDS no longer pretends 1-element arrays are unbounded. Walking
bmSublinkSpeedAttr will trigger a warning, so make it a proper flexible
array. Add a union to keep the struct size identical for userspace in
case anything was depending on the old size.
False positive warning was:
UBSAN: array-index-out-of-bounds in drivers/usb/host/xhci-hub.c:231:31 index 1 is out of range for type '__le32 [1]'
for this line of code:
ssp_cap->bmSublinkSpeedAttr[offset++] = cpu_to_le32(attr);
Reported-by: Borislav Petkov <bp@alien8.de>
Closes: https://lore.kernel.org/lkml/2023062945-fencing-pebble-0411@gregkh/
Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Closes: https://lore.kernel.org/lkml/9a8e34ad-8a8b-3830-4878-3c2c82e69dd9@alu.unizg.hr/
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Tested-by: "Borislav Petkov (AMD)" <bp@alien8.de>
Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20230629190900.never.787-kees@kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
Pull more xfs updates from Darrick Wong:
- Fix some ordering problems with log items during log recovery
- Don't deadlock the system by trying to flush busy freed extents while
holding on to busy freed extents
- Improve validation of log geometry parameters when reading the
primary superblock
- Validate the length field in the AGF header
- Fix recordset filtering bugs when re-calling GETFSMAP to return more
results when the resultset didn't previously fit in the caller's
buffer
- Fix integer overflows in GETFSMAP when working with rt volumes larger
than 2^32 fsblocks
- Fix GETFSMAP reporting the undefined space beyond the last rtextent
- Fix filtering bugs in GETFSMAP's log device backend if the log ever
becomes longer than 2^32 fsblocks
- Improve validation of file offsets in the GETFSMAP range parameters
- Fix an off by one bug in the pmem media failure notification
computation
- Validate the length field in the AGI header too
* tag 'xfs-6.5-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Remove unneeded semicolon
xfs: AGI length should be bounds checked
xfs: fix the calculation for "end" and "length"
xfs: fix xfs_btree_query_range callers to initialize btree rec fully
xfs: validate fsmap offsets specified in the query keys
xfs: fix logdev fsmap query result filtering
xfs: clean up the rtbitmap fsmap backend
xfs: fix getfsmap reporting past the last rt extent
xfs: fix integer overflows in the fsmap rtbitmap and logdev backends
xfs: fix interval filtering in multi-step fsmap queries
xfs: fix bounds check in xfs_defer_agfl_block()
xfs: AGF length has never been bounds checked
xfs: journal geometry is not properly bounds checked
xfs: don't block in busy flushing when freeing extents
xfs: allow extent free intents to be retried
xfs: pass alloc flags through to xfs_extent_busy_flush()
xfs: use deferred frees for btree block freeing
xfs: don't reverse order of items in bulk AIL insertion
xfs: remove redundant initializations of pointers drop_leaf and save_leaf
|
|
The IXP4XX_EXP_T1_MASK was shifted one bit to the right, overlapping
IXP4XX_EXP_T2_MASK and leaving bit 29 unused. The offset being wrong is
also confirmed at least by the datasheet of IXP45X/46X [1].
Fix this by aligning it to IXP4XX_EXP_T1_SHIFT.
[1] https://www.intel.com/content/dam/www/public/us/en/documents/manuals/ixp45x-ixp46x-developers-manual.pdf
Cc: stable@vger.kernel.org
Fixes: 1c953bda90ca ("bus: ixp4xx: Add a driver for IXP4xx expansion bus")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Link: https://lore.kernel.org/r/20230624112958.27727-1-jonas.gorski@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230624122139.3229642-1-linus.walleij@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add missing whitespace between node name/label and opening {.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230705150033.293832-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Randy reported build errors in linux-next where XIP_KERNEL was enabled.
ARCH_THEAD requires alternatives to support the non-standard ISA
extensions used by the THEAD cores, which are mutually exclusive with
XIP kernels. Clone the dependency list from the Allwinner entry, since
Allwinner's D1 uses T-Head cores with the same non-standard extensions.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Link: https://lore.kernel.org/all/ab38f6af-cb68-a918-1a63-2e7c927a8ffc@infradead.org/
Fixes: da47ce003963 ("riscv: Add the T-HEAD SoC family Kconfig option")
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230628-left-attractor-94b7bd5fbb83@wendy
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There's a little bit of everything in here: we've got various
improvements and cleanups to drivers, some fixes across the board and
a bit of new hardware support"
* tag 'pwm/for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (22 commits)
dt-bindings: pwm: convert pwm-bcm2835 bindings to YAML
pwm: Add Renesas RZ/G2L MTU3a PWM driver
pwm: mtk_disp: Fix the disable flow of disp_pwm
dt-bindings: pwm: restrict node name suffixes
pwm: pca9685: Switch i2c driver back to use .probe()
pwm: ab8500: Fix error code in probe()
MAINTAINERS: add pwm to PolarFire SoC entry
pwm: add microchip soft ip corePWM driver
pwm: sysfs: Do not apply state to already disabled PWMs
pwm: imx-tpm: force 'real_period' to be zero in suspend
pwm: meson: make full use of common clock framework
pwm: meson: don't use hdmi/video clock as mux parent
pwm: meson: switch to using struct clk_parent_data for mux parents
pwm: meson: remove not needed check in meson_pwm_calc
pwm: meson: fix handling of period/duty if greater than UINT_MAX
pwm: meson: modify and simplify calculation in meson_pwm_get_state
dt-bindings: pwm: Add R-Car V3U device tree bindings
dt-bindings: pwm: imx: add i.MX8QXP compatible
pwm: mediatek: Add support for MT7981
dt-bindings: pwm: mediatek: Add mediatek,mt7981 compatible
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
- Whitespace clean-ups in binding examples
- Restrict node name suffixes to "-[0-9]+" for cases of multiple
instances which don't have unit-addresses
- Convert brcm,kona-wdt and cdns,wdt-r1p2 watchdog bindings to DT
schema
* tag 'devicetree-for-6.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: soc: qcom: stats: Update maintainer email
dt-bindings: cleanup DTS example whitespaces
dt-bindings: timestamp: restrict node name suffixes
dt-bindings: slimbus: restrict node name suffixes
dt-bindings: watchdog: restrict node name suffixes
dt-bindings: watchdog: brcm,kona-wdt: convert txt file to yaml
dt-bindings: watchdog: cdns,wdt-r1p2: Convert cadence watchdog to yaml
|
|
supported.
Arm has multiple PMU types for heterogeneous systems, but doesn't
currently support PERF_PMU_CAP_EXTENDED_HW_TYPE. Make the tests
support both scenarios so that they pass on Arm, and will still pass
once PERF_PMU_CAP_EXTENDED_HW_TYPE support is added.
Fixes: 27c9fcfc1e14 ("perf test: Update parse-events expectations to test for multiple events")
Acked-by: Ian Rogers <irogers@google.com>
Signed-off-by: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230705082653.23566-3-james.clark@arm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
|
|
The test looks for a PMU from sysfs with type = PERF_TYPE_RAW when
opening a raw event. Arm doesn't have a real raw PMU, only core PMUs
with unique types other than raw.
Instead of looking for a matching PMU, just test that the event type
was parsed as raw and skip the PMU search on Arm. The raw event type
test should also apply to all platforms so add it outside of the ifdef.
Fixes: aefde50a446b ("perf test: Fix parse-events tests for >1 core PMU")
Acked-by: Ian Rogers <irogers@google.com>
Signed-off-by: James Clark <james.clark@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Link: https://lore.kernel.org/r/20230705082653.23566-2-james.clark@arm.com
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
|
|
When moving devices from one namespace to another, mc addresses are
cleaned in software while not removed from application firmware. Thus
the mc addresses are remained and will cause resource leak.
Now use `__dev_mc_unsync` to clean mc addresses when closing port.
Fixes: e20aa071cd95 ("nfp: fix schedule in atomic context when sync mc address")
Cc: stable@vger.kernel.org
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Message-ID: <20230705052818.7122-1-louis.peens@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-07-05
We've added 2 non-merge commits during the last 1 day(s) which contain
a total of 3 files changed, 16 insertions(+), 4 deletions(-).
The main changes are:
1) Fix BTF to warn but not returning an error for a NULL BTF to still be
able to load modules under CONFIG_DEBUG_INFO_BTF, from SeongJae Park.
2) Fix xsk sockets to honor SO_BINDTODEVICE in bind(), from Ilya Maximets.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
xsk: Honor SO_BINDTODEVICE on bind
bpf, btf: Warn but return no error for NULL btf from __register_btf_kfunc_id_set()
====================
Link: https://lore.kernel.org/r/20230705171716.6494-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire updates from Vinod Koul:
- Stream handling and slave alert handling
- Qualcomm Soundwire v2.0.0 controller support
- Intel ACE2.x initial support and code reorganization
* tag 'soundwire-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire: (55 commits)
soundwire: stream: Make master_list ordered to prevent deadlocks
soundwire: bus: Prevent lockdep asserts when stream has multiple buses
soundwire: qcom: fix storing port config out-of-bounds
soundwire: intel_ace2x: fix SND_SOC_SOF_HDA_MLINK dependency
soundwire: debugfs: Add missing SCP registers
soundwire: stream: Remove unnecessary gotos
soundwire: stream: Invert logic on runtime alloc flags
soundwire: stream: Remove unneeded checks for NULL bus
soundwire: bandwidth allocation: Remove pointless variable
soundwire: cadence: revisit parity injection
soundwire: intel/cadence: update hardware reset sequence
soundwire: intel_bus_common: enable interrupts last
soundwire: intel_bus_common: update error log
soundwire: amd: Improve error message in remove callback
soundwire: debugfs: fix unbalanced pm_runtime_put()
soundwire: qcom: fix unbalanced pm_runtime_put()
soundwire: qcom: set clk stop need reset flag at runtime
soundwire: qcom: add software workaround for bus clash interrupt assertion
soundwire: qcom: wait for fifo to be empty before suspend
soundwire: qcom: drop unused struct qcom_swrm_ctrl members
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvement at atomisp driver, which is starting to look in
good shape
- Mediatek vcodec driver has gained support for av1 and hevc stateless
codecs
- New sensor driver: ov01a10
- verisilicon driver has gained AV1 entropy helpers
- tegra-video has gained support for Tegra20 parallel input
- dvb core has gained an extra property to better support DVB-S2X
- as usual, lots of cleanups, fixes and improvements on media drivers
* tag 'media/v6.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (253 commits)
media: wl128x: fix a clang warning
media: dvb: mb86a20s: get rid of a clang-15 warning
media: cec: i2c: ch7322: also select REGMAP
media: add HAS_IOPORT dependencies
media: tc358746: select CONFIG_GENERIC_PHY
media: mediatek: vcodec: Add dbgfs help function
media: mediatek: vcodec: Add encode to support dbgfs
media: mediatek: vcodec: Change dbgfs interface to support encode
media: mediatek: vcodec: Get each instance format type
media: mediatek: vcodec: Get each context resolution information
media: mediatek: vcodec: Add a debugfs file to get different useful information
media: mediatek: vcodec: Add debug params to control different log level
media: mediatek: vcodec: Add debugfs interface to get debug information
media: mediatek: vcodec: support stateless AV1 decoder
media: verisilicon: Conditionally ignore native formats
media: verisilicon: Enable AV1 decoder on rk3588
media: verisilicon: Add film grain feature to AV1 driver
media: verisilicon: Add Rockchip AV1 decoder
media: verisilicon: Add AV1 entropy helpers
media: verisilicon: Compute motion vectors size for AV1 frames
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing tooling updates from Steven Rostedt:
- Add cgroup support for rtla via the -C option
- Add --house-keeping option that tells rtla where to place the
housekeeping threads
- Have rtla/timerlat have its own tracing instance instead of using the
top level tracing instance that is the default for other tracing
users to use
- Add auto analysis to timerlat_hist
- Have rtla start the tracers after creating the instances
- Reduce rtla hwnoise down to 75% from 100% as it runs with preemption
disabled and can cause system instability at 100%
- Add support to run timerlat_top and timerlat_hist threads in
user-space instead of just using the kernel tasks
- Some minor clean ups and documentation changes
* tag 'trace-tools-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
Documentation: Add tools/rtla timerlat -u option documentation
rtla/timerlat_hist: Add timerlat user-space support
rtla/timerlat_top: Add timerlat user-space support
rtla/hwnoise: Reduce runtime to 75%
rtla: Start the tracers after creating all instances
rtla/timerlat_hist: Add auto-analysis support
rtla/timerlat: Give timerlat auto analysis its own instance
rtla: Automatically move rtla to a house-keeping cpu
rtla: Change monitored_cpus from char * to cpu_set_t
rtla: Add --house-keeping option
rtla: Add -C cgroup support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
- Fix all compiler warnings in arch/parisc and drivers/parisc when
compiled with W=1
* tag 'parisc-for-6.5-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: syscalls: Avoid compiler warnings with W=1
parisc: math-emu: Avoid compiler warnings with W=1
parisc: Raise minimal GCC version to 12.0.0
parisc: unwind: Avoid missing prototype warning for handle_interruption()
parisc: smp: Add declaration for start_cpu_itimer()
parisc: pdt: Get prototype for arch_report_meminfo()
|
|
The unxlate_dev_mem_ptr() function has no prototype on the sh architecture
which does not include asm-generic/io.h. This results in the following
build failure:
drivers/char/mem.c: In function 'read_mem':
drivers/char/mem.c:164:25: error: implicit declaration of function 'unxlate_dev_mem_ptr'
This compile error is now seen because commit 99b619b37ae1 ("mips: provide
unxlate_dev_mem_ptr() in asm/io.h") removed the weak function which was
previously in place to handle this problem.
Add a trivial macro to the sh header to provide the now missing dummy
function.
Fixes: 99b619b37ae1 ("mips: provide unxlate_dev_mem_ptr() in asm/io.h")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230704190144.2888679-1-linux@roeck-us.net
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
According to the hardware manual [1], the DMAC found in the SH7709 SoC
features only 4 channels. While at it, also sort the existing targets.
[1] https://www.renesas.com/us/en/document/mah/sh7709s-group-hardware-manual (p. 373)
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230527164452.64797-4-contact@artur-rojek.eu
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
None of the supported SH4 family SoCs features a second DMAC module. As
this definition negatively impacts DMA channel calculation for the above
targets, remove it from the code.
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230527164452.64797-3-contact@artur-rojek.eu
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
Various SoCs of the SH3, SH4 and SH4A family, which use this driver,
feature a differing number of DMA channels, which can be distributed
between up to two DMAC modules. The existing implementation fails to
correctly accommodate for all those variations, resulting in wrong
channel offset calculations and leading to kernel panics.
Rewrite dma_base_addr() in order to properly calculate channel offsets
in a DMAC module. Fix dmaor_read_reg() and dmaor_write_reg(), so that
the correct DMAC module base is selected for the DMAOR register.
Fixes: 7f47c7189b3e8f19 ("sh: dma: More legacy cpu dma chainsawing.")
Signed-off-by: Artur Rojek <contact@artur-rojek.eu>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230527164452.64797-2-contact@artur-rojek.eu
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
|
Every compiler flag added by arch/sh/Makefile is passed to the
compiler twice:
$(KBUILD_CPPFLAGS) + $(KBUILD_CFLAGS) is used for compiling *.c
$(KBUILD_CPPFLAGS) + $(KBUILD_AFLAGS) is used for compiling *.S
Given the above, adding $(cflags-y) to all of KBUILD_{CPP/C/A}FLAGS
ends up with duplication.
Add -I options to $(KBUILD_CPPFLAGS), and the rest of $(cflags-y)
to KBUILD_{C,A}FLAGS.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/20230219141555.2308306-4-masahiroy@kernel.org
Signed-off-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
|
