| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
AC excitation enable feature exposed to user on AD7192, allowing a bit
which should be 0 to be set. This feature is specific only to AD7195. AC
excitation attribute moved accordingly.
In the AD7195 documentation, the AC excitation enable bit is on position
22 in the Configuration register. ACX macro changed to match correct
register and bit.
Note that the fix tag is for the commit that moved the driver out of
staging.
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Alisa Roman <alisa.roman@analog.com>
Cc: stable@vger.kernel.org
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230614155242.160296-1-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This patch adds an example showing how to use PFSM devices
from a userspace application. The PMIC is armed to be triggered
by a RTC alarm to execute state transition.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Message-ID: <20230511095126.105104-7-jpanis@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds documentation for the TPS6594 PFSM driver.
The PFSM controls the operational states of the TPS6594 PMIC.
Depending on the operational mode, some power domain networks
remain energized while others can be off.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Message-ID: <20230511095126.105104-6-jpanis@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This PFSM controls the operational modes of the PMIC:
- STANDBY and LP_STANDBY,
- ACTIVE state,
- MCU_ONLY state,
- RETENTION state, with or without DDR and/or GPIO retention.
Depending on the current operational mode, some voltage domains
remain energized while others can be off.
This PFSM is also used to trigger a firmware update, and provides
R/W access to device registers.
See Documentation/misc-devices/tps6594-pfsm.rst for more
information.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Message-ID: <20230511095126.105104-5-jpanis@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for TPS6594 ESM (Error Signal Monitor).
This device monitors the SoC error output signal at its nERR_SOC input pin.
In error condition, ESM toggles its nRSTOUT_SOC pin to reset the SoC.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Message-ID: <20230511095126.105104-4-jpanis@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into char-misc-next
Immutable branch containing TPS6594 core (MFD) support due for the v6.5 merge window
We want this due to patches requiring this mfd support.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'ib-mfd-tps6594-core-v6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: tps6594: Add driver for TI TPS6594 PMIC
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wbg/counter into char-misc-next
William writes:
First set of Counter updates for the 6.5 cycle
Biggest changes in this set include the introduction of a new Intel 8254
interface library module and the refactoring of the existing 104-quad-8
modules to migrate it to the regmap API. Some other minor cleanups
touching tools/counter and stm32-timer-cnt are also present.
Changes
* 104-quad-8
- Remove reference in Kconfig to 25-bit counter value
- Utilize bitfield access macros
- Refactor to buffer states for CMR, IOR, and IDR
- Utilize helper functions to handle PR, FLAG and PSC
- Migrate to the regmap API
* i8254
- Introduce the Intel 8254 interface library module
* stm32-timer-cnt
- Reset TIM_TISEL to its default value in probe
* tools/counter
- Add .gitignore
- Remove lingering 'include' directories on make clean
* tag 'counter-updates-for-6.5a' of git://git.kernel.org/pub/scm/linux/kernel/git/wbg/counter:
counter: i8254: Introduce the Intel 8254 interface library module
counter: 104-quad-8: Migrate to the regmap API
counter: 104-quad-8: Utilize helper functions to handle PR, FLAG and PSC
counter: 104-quad-8: Refactor to buffer states for CMR, IOR, and IDR
counter: 104-quad-8: Utilize bitfield access macros
tools/counter: Makefile: Remove lingering 'include' directories on make clean
tools/counter: Add .gitignore
counter: stm32-timer-cnt: Reset TIM_TISEL to its default value in probe
counter: 104-quad-8: Remove reference in Kconfig to 25-bit counter value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga into char-misc-next
Xu writes:
FPGA Manager changes for 6.5-rc1
DFL:
- Krzysztof's change constifies pointers to hwmon_channel_info
Xilinx:
- Alfonso's change ensures proper reprograming (xCAP) interface switch
All patches have been reviewed on the mailing list, and have been in the
last linux-next releases (as part of our for-next branch).
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
* tag 'fpga-for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/fpga/linux-fpga:
fpga: zynq-fpga: Ensure proper xCAP interface switch
fpga: dfl-fme: constify pointers to hwmon_channel_info
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for the 6.5 cycle.
New device support
- honeywell,mprls0025pa
* New driver and dt-bindings for this series of pressure sensors.
- invensense,mpu6050
* Add support for ICM 20600 IMU (ID, bindings and device data).
- melexis,mlx90614
* Add support for mlx90615 Infra Red Thermometer after driver cleanup
and refactoring to support the differences in this device.
- renesas,x9250
* New driver and bindings for this quad potentiometer.
- rockchip,saradc
* Add support for RK3588. Also included is a bunch of refactoring and
cleanup for that driver.
- rohm,bu27008
* New driver bindings etc for this 5 photodiode color sensor.
- st,lsm9ds0/st,st-sensors
* ID added for LSM303D accelerometer and magnetometer including ACPI binding.
- ti,opt4001
* New driver and bindings for this ambient light sensor.
Features
- core
* Introduce iio_validate_own_trigger() for cases where a driver can only
consumer a trigger it registered (detected via same parent device).
Use it in the kionix,kx022a driver and new rohm,by27008 driver.
- dynaimage,al3320a
* ACPI binding CALS0001 seen on Lenovo Yoga Table 2 devices.
- kionix,kx002a
* Enable asynchronous probe.
- rohm,bu27034
* Enable asynchronous probe.
- ti,tmp006
* Explicit support for DT including binding documentation.
Cleanups, minor fixes and misc improvements.
- treewide
* Switch I2C drivers from probe_new() back to probe() - part of the
long process of getting rid of a parameter from probe()
* Various whitespace and typo fixes not otherwise called out.
- core
* industrialio-buffer,Style cleanup.
* Add documentation to extend_name field of struct iio_chan_spec to
direct people using it towards the label infrastructure instead.
extend_name was a design mistake a long time back so directly people
away from it may be useful.
- adi,ad7606
* Add HAS_IOPORT dependency to prepare for some Kconfig changes.
- bosch,bma400
* Drop pointless print of ret in a dev_err_probe() message.
- invensense,icm42600
* Rework timestamp handling to reduce jitter.
- mediatek,mt7986-auxdac
* Add DT binding for this part.
- qcom,spmi-vadc
* Allow for 1/16th prescaling used on a few devices.
* Various changes to channel labeling and naming, including dropping
use of fwnode_name which generates odd channel names. Small ABI
change as a result, but not thought to be a problem for users of this
platform.
- st,lsm6dsx
* dt-binding: Use common schema for mount-matrix via a reference.
- st,stm32
* Add a debug print for when legacy channel config is used.
- ti,palmas-adc
* Drop unused i2c.h include.
* tag 'iio-for-6.5a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (59 commits)
dt-bindings: iio: rockchip: Fix 'oneOf' condition failed warning
dt-bindings: iio: afe: voltage-divider: Spelling s/curcuit/circuit/
dt-bindings: iio: adc: Add rockchip,rk3588-saradc string
iio: adc: rockchip_saradc: Use dev_err_probe
iio: adc: rockchip_saradc: Match alignment with open parenthesis
iio: adc: rockchip_saradc: Use of_device_get_match_data
iio: adc: rockchip_saradc: Make use of devm_clk_get_enabled
iio: adc: rockchip_saradc: Add support for RK3588
iio: adc: rockchip_saradc: Add callback functions
iio: temperature: tmp006: Add OF device matching support
dt-bindings: iio: temperature: Add support for tmp006
staging: iio: Switch i2c drivers back to use .probe()
iio: amplifiers: ad8366 Fix whitespace issue
iio: imu: inv_icm42600: avoid frequent timestamp jitter
MAINTAINERS: Add ROHM BU27008
iio: light: ROHM BU27008 color sensor
iio: kx022a: Use new iio_validate_own_trigger()
iio: trigger: Add simple trigger_validation helper
dt-bindings: iio: light: ROHM BU27008
iio: mlx90614: Add MLX90615 support
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
2nd set of IIO fixes for the 6.4 cycle.
Given how late this pull request is, I'm expecting these to get queued
up for the 6.5 merge window.
- adi,ad7192
* Fix a null pointer as spi_set_drvdata() is no longer called.
* Fix wrong check prior to using internal clock.
* Fix dt-binding to make it clear the voltage reference is required.
- adi,ad74413
* DIN_SINK should not be set for functions other than digital inputs.
Enforce that in the driver.
- amlogic,meson-saradc
* Fix clock divider mask length - affects only meson 8 family.
- freescale,fxls8962af
* Fix endian type and shift of channels to match with default device setup.
* Narrow errata handling to FXLS8962AF only as doesn't affect other devices
supported by this driver.
* tag 'iio-fixes-for-6.4b' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
meson saradc: fix clock divider mask length
iio: accel: fxls8962af: errata bug only applicable for FXLS8962AF
iio: accel: fxls8962af: fixup buffer scan element type
dt-bindings: iio: ad7192: Add mandatory reference voltage source
iio: adc: ad7192: Fix internal/external clock selection
iio: adc: ad7192: Fix null ad7192_state pointer access
iio: addac: ad74413: don't set DIN_SINK for functions other than digital input
|
|
rk3588-saradc isn't compatible with the rk3399-saradc variant,
hence, fix the following dtbs_check warning for 'oneOf' condition
failure.
DTC_CHK arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dtb
/home/shreeya/linux/arch/arm64/boot/dts/rockchip/rk3588-rock-5b.dtb:
saradc@fec10000: compatible: 'oneOf' conditional failed,
one must be fixed:
['rockchip,rk3588-saradc'] is too short
'rockchip,saradc' was expected
'rockchip,rk3066-tsadc' was expected
'rockchip,rk3399-saradc' was expected
Fixes: 2daf2ae9793d ("dt-bindings: iio: adc: Add rockchip,rk3588-saradc string")
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230610143601.173307-1-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
According to the datasheets of supported meson SoCs length of ADC_CLK_DIV
field is 6-bit. Although all supported SoCs have the register
with that field documented later SoCs use external clock rather than
ADC internal clock so this patch affects only meson8 family (S8* SoCs).
Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: George Stark <GNStark@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20230606165357.42417-1-gnstark@sberdevices.ru
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix a misspelling of "circuit".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/a8597e54b55dedc51025fe3073d25ef0d659d0dc.1686045793.git.geert+renesas@glider.be
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Exposes consumer library functions providing support for interfaces
compatible with the venerable Intel 8254 Programmable Interval Timer
(PIT).
The Intel 8254 PIT first appeared in the early 1980s and was used
initially in IBM PC compatibles. The popularity of the original Intel
825x family of chips led to many subsequent variants and clones of the
interface in various chips and integrated circuits. Although still
popular, interfaces compatible with the Intel 8254 PIT are nowdays
typically found embedded in larger VLSI processing chips and FPGA
components rather than as discrete ICs.
A CONFIG_I8254 Kconfig option is introduced by this patch. Modules
wanting access to these i8254 library functions should select this
Kconfig option, and import the I8254 symbol namespace.
Link: https://lore.kernel.org/r/f6fe32c2db9525d816ab1a01f45abad56c081652.1681665189.git.william.gray@linaro.org/
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
|
|
The Zynq platform has PCAP, ICAP and JTAG interfaces for configuring
programmable logic (PL). The existing driver implementation uses the
PCAP interface to configure the PL. Before switching the PL configuration
interface from PCAP to ICAP make sure that all outstanding Transactions
relevant to the PL configuration should be completed by the PCAP interface
otherwise it may lead to PL configuration issues.
This patch provides a required fix to ensure that all existing PL
transactions are completed before switching from PCAP to ICAP.
For detailed information relevant to PL configuration interfaces refer
Zynq 7000 TRM (section 6.5.1).
Link: https://docs.xilinx.com/v/u/en-US/ug585-Zynq-7000-TRM
Signed-off-by: Alfonso Rodriguez <alfonso.rodriguezm@upm.es>
Signed-off-by: Nava kishore Manne <nava.kishore.manne@amd.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Link: https://lore.kernel.org/r/20230605115433.186087-1-nava.kishore.manne@amd.com
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
|
|
Remove special errata handling if FXLS8964AF is used.
Fixes: af959b7b96b8 ("iio: accel: fxls8962af: fix errata bug E3 - I2C burst reads")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230605103223.1400980-2-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Scan elements for x,y,z channels is little endian and requires no bit shifts.
LE vs. BE is controlled in register SENS_CONFIG2 and bit LE_BE, default
value is LE.
Fixes: a3e0b51884ee ("iio: accel: add support for FXLS8962AF/FXLS8964AF accelerometers")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230605103223.1400980-1-sean@geanix.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
We need the char/misc fixes in here as well for mergeing and testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Borislav Petkov:
- Fix open firmware quirks validation so that they don't get applied
wrongly
* tag 'irq_urgent_for_v6.4_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic: Correctly validate OF quirk descriptors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Some driver fixes:
- a regression fix for the verisilicon driver
- uvcvideo: don't expose unsupported video formats to userspace
- camss-video: don't zero subdev format after init
- mediatek: some fixes for 4K decoder formats
- fix a Sphinx build warning (missing doc for client_caps)
- some fixes for imx and atomisp staging drivers
And two CEC core fixes:
- don't set last_initiator if TX in progress
- disable adapter in cec_devnode_unregister"
* tag 'media/v6.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: uvcvideo: Don't expose unsupported formats to userspace
media: v4l2-subdev: Fix missing kerneldoc for client_caps
media: staging: media: imx: initialize hs_settle to avoid warning
media: v4l2-mc: Drop subdev check in v4l2_create_fwnode_links_to_pad()
media: staging: media: atomisp: init high & low vars
media: cec: core: don't set last_initiator if tx in progress
media: cec: core: disable adapter in cec_devnode_unregister
media: mediatek: vcodec: Only apply 4K frame sizes on decoder formats
media: camss: camss-video: Don't zero subdev format again after initialization
media: verisilicon: Additional fix for the crash when opening the driver
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a bunch of tiny char/misc/other driver fixes for 6.4-rc5 that
resolve a number of reported issues. Included in here are:
- iio driver fixes
- fpga driver fixes
- test_firmware bugfixes
- fastrpc driver tiny bugfixes
- MAINTAINERS file updates for some subsystems
All of these have been in linux-next this past week with no reported
issues"
* tag 'char-misc-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (34 commits)
test_firmware: fix the memory leak of the allocated firmware buffer
test_firmware: fix a memory leak with reqs buffer
test_firmware: prevent race conditions by a correct implementation of locking
firmware_loader: Fix a NULL vs IS_ERR() check
MAINTAINERS: Vaibhav Gupta is the new ipack maintainer
dt-bindings: fpga: replace Ivan Bornyakov maintainership
MAINTAINERS: update Microchip MPF FPGA reviewers
misc: fastrpc: reject new invocations during device removal
misc: fastrpc: return -EPIPE to invocations on device removal
misc: fastrpc: Reassign memory ownership only for remote heap
misc: fastrpc: Pass proper scm arguments for secure map request
iio: imu: inv_icm42600: fix timestamp reset
iio: adc: ad_sigma_delta: Fix IRQ issue by setting IRQ_DISABLE_UNLAZY flag
dt-bindings: iio: adc: renesas,rcar-gyroadc: Fix adi,ad7476 compatible value
iio: dac: mcp4725: Fix i2c_master_send() return value handling
iio: accel: kx022a fix irq getting
iio: bu27034: Ensure reset is written
iio: dac: build ad5758 driver when AD5758 is selected
iio: addac: ad74413: fix resistance input processing
iio: light: vcnl4035: fixed chip ID check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are two small driver core cacheinfo fixes for 6.4-rc5 that
resolve a number of reported issues with that file. These changes have
been in linux-next this past week with no reported problems"
* tag 'driver-core-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers: base: cacheinfo: Update cpu_map_populated during CPU Hotplug
drivers: base: cacheinfo: Fix shared_cpu_map changes in event of CPU hotplug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty/serial driver fixes for 6.4-rc5 that have all
been in linux-next this past week with no reported problems. Included
in here are:
- 8250_tegra driver bugfix
- fsl uart driver bugfixes
- Kconfig fix for dependancy issue
- dt-bindings fix for the 8250_omap driver"
* tag 'tty-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
dt-bindings: serial: 8250_omap: add rs485-rts-active-high
serial: cpm_uart: Fix a COMPILE_TEST dependency
soc: fsl: cpm1: Fix TSA and QMC dependencies in case of COMPILE_TEST
tty: serial: fsl_lpuart: use UARTCTRL_TXINV to send break instead of UARTCTRL_SBK
serial: 8250_tegra: Fix an error handling path in tegra_uart_probe()
|
|
Add required reference voltage (VRef) supply regulator.
AD7192 requires three independent voltage sources: DVdd, AVdd and VRef
(on REFINx pin pairs).
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Fabrizio Lamarque <fl.scratchpad@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230530075311.400686-5-fl.scratchpad@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix wrong selection of internal clock when mclk is defined.
Resolve a logical inversion introduced in c9ec2cb328e3.
Fixes: c9ec2cb328e3 ("iio: adc: ad7192: use devm_clk_get_optional() for mclk")
Signed-off-by: Fabrizio Lamarque <fl.scratchpad@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230530075311.400686-3-fl.scratchpad@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Pointer to indio_dev structure is obtained via spi_get_drvdata() at
the beginning of function ad7192_setup(), but the spi->dev->driver_data
member is not initialized, hence a NULL pointer is returned.
Fix by changing ad7192_setup() signature to take pointer to struct
iio_dev, and get ad7192_state pointer via st = iio_priv(indio_dev);
Fixes: bd5dcdeb3fd0 ("iio: adc: ad7192: convert to device-managed functions")
Signed-off-by: Fabrizio Lamarque <fl.scratchpad@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230530075311.400686-2-fl.scratchpad@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver and core fixes for 6.4-rc5. Most of these are
tiny driver fixes, including:
- udc driver bugfix
- f_fs gadget driver bugfix
- cdns3 driver bugfix
- typec bugfixes
But the "big" thing in here is a fix yet-again for how the USB buffers
are handled from userspace when dealing with DMA issues. The changes
were discussed a lot, and tested a lot, on the list, and acked by the
relevant mm maintainers and have been in linux-next all this past week
with no reported problems"
* tag 'usb-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: tps6598x: Fix broken polling mode after system suspend/resume
mm: page_table_check: Ensure user pages are not slab pages
mm: page_table_check: Make it dependent on EXCLUSIVE_SYSTEM_RAM
usb: usbfs: Use consistent mmap functions
usb: usbfs: Enforce page requirements for mmap
dt-bindings: usb: snps,dwc3: Fix "snps,hsphy_interface" type
usb: gadget: udc: fix NULL dereference in remove()
usb: gadget: f_fs: Add unbind event before functionfs_unbind
usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM
|
|
Apparently, despite the name Digital Input Configuration Register, the
settings in the DIN_CONFIGx registers also affect other channel
functions. In particular, setting a non-zero value in the DIN_SINK
field breaks the resistance measurement function.
Now, one can of course argue that specifying a drive-strength-microamp
property along with a adi,ch-func which is not one of the digital
input functions is a bug in the device tree. However, we have a rather
complicated setup with instances of ad74412r on external hardware
modules, and have set a default drive-strength-microamp in our DT
fragments describing those, merely modifying the adi,ch-func settings
to reflect however the modules have been wired up. And restricting
this setting to just being done for digital input doesn't make the
driver any more complex.
Fixes: 504eb485589d1 (iio: ad74413r: wire up support for drive-strength-microamp property)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Link: https://lore.kernel.org/r/20230503105042.453755-1-linux@rasmusvillemoes.dk
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Address some fallout of the locking rework, this time affecting the
way the vgic is configured
- Fix an issue where the page table walker frees a subtree and then
proceeds with walking what it has just freed...
- Check that a given PA donated to the guest is actually memory (only
affecting pKVM)
- Correctly handle MTE CMOs by Set/Way
- Fix the reported address of a watchpoint forwarded to userspace
- Fix the freeing of the root of stage-2 page tables
- Stop creating spurious PMU events to perform detection of the
default PMU and use the existing PMU list instead
x86:
- Fix a memslot lookup bug in the NX recovery thread that could
theoretically let userspace bypass the NX hugepage mitigation
- Fix a s/BLOCKING/PENDING bug in SVM's vNMI support
- Account exit stats for fastpath VM-Exits that never leave the super
tight run-loop
- Fix an out-of-bounds bug in the optimized APIC map code, and add a
regression test for the race"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: selftests: Add test for race in kvm_recalculate_apic_map()
KVM: x86: Bail from kvm_recalculate_phys_map() if x2APIC ID is out-of-bounds
KVM: x86: Account fastpath-only VM-Exits in vCPU stats
KVM: SVM: vNMI pending bit is V_NMI_PENDING_MASK not V_NMI_BLOCKING_MASK
KVM: x86/mmu: Grab memslot for correct address space in NX recovery worker
KVM: arm64: Document default vPMU behavior on heterogeneous systems
KVM: arm64: Iterate arm_pmus list to probe for default PMU
KVM: arm64: Drop last page ref in kvm_pgtable_stage2_free_removed()
KVM: arm64: Populate fault info for watchpoint
KVM: arm64: Reload PTE after invoking walker callback on preorder traversal
KVM: arm64: Handle trap of tagged Set/Way CMOs
arm64: Add missing Set/Way CMO encodings
KVM: arm64: Prevent unconditional donation of unmapped regions from the host
KVM: arm64: vgic: Fix a comment
KVM: arm64: vgic: Fix locking comment
KVM: arm64: vgic: Wrap vgic_its_create() with config_lock
KVM: arm64: vgic: Fix a circular locking issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- Fix link errors in new aes-gcm-p10 code when built-in with other
drivers
- Limit number of TCEs passed to H_STUFF_TCE hcall as per spec
- Use KSYM_NAME_LEN in xmon array size to avoid possible OOB write
Thanks to Gaurav Batra and Maninder Singh Vishal Chourasia.
* tag 'powerpc-6.4-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/xmon: Use KSYM_NAME_LEN in array size
powerpc/iommu: Limit number of TCEs to 512 for H_STUFF_TCE hcall
powerpc/crypto: Fix aes-gcm-p10 link errors
|
|
Add rockchip,rk3588-saradc compatible string.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230603185340.13838-9-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use dev_err_probe instead of dev_err in probe function,
which simplifies code a little bit and prints the error
code.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-7-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Match alignment with open parenthesis for improving the code
readability.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230603185340.13838-6-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-5-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use devm_clk_get_enabled() to avoid manually disabling the
clock.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-4-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add new start and read functions to support rk3588 device.
Also, add a device compatible string for the same.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230603185340.13838-3-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add start, read and power_down callback functions,
which will help in adding new rockchip device support
cleanly.
Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230603185340.13838-2-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
KVM x86 fixes for 6.4
- Fix a memslot lookup bug in the NX recovery thread that could
theoretically let userspace bypass the NX hugepage mitigation
- Fix a s/BLOCKING/PENDING bug in SVM's vNMI support
- Account exit stats for fastpath VM-Exits that never leave the super
tight run-loop
- Fix an out-of-bounds bug in the optimized APIC map code, and add a
regression test for the race.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.4, take #3
- Fix the reported address of a watchpoint forwarded to userspace
- Fix the freeing of the root of stage-2 page tables
- Stop creating spurious PMU events to perform detection of the
default PMU and use the existing PMU list instead.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.4, take #2
- Address some fallout of the locking rework, this time affecting
the way the vgic is configured
- Fix an issue where the page table walker frees a subtree and
then proceeds with walking what it has just freed...
- Check that a given PA donated to the gues is actually memory
(only affecting pKVM)
- Correctly handle MTE CMOs by Set/Way
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Five fixes, all in drivers.
The most extensive is the target change to fix the hang in the login
code, which involves changing timers from per login to per connection"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: stex: Fix gcc 13 warnings
scsi: qla2xxx: Fix NULL pointer dereference in target mode
scsi: target: iscsi: Prevent login threads from racing between each other
scsi: target: iscsi: Remove unused transport_timer
scsi: target: iscsi: Fix hang in the iSCSI login code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/linux
Pull LED fix from Johan Hovold:
"Here's a fix for a regression in 6.4-rc1 which broke the backlight on
machines such as the Lenovo ThinkPad X13s"
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/lkml/20230602091928.GR449117@google.com/
* tag 'leds-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/linux:
leds: qcom-lpg: Fix PWM period limits
|
|
The introduction of high resolution PWM support changed the order of the
operations in the calculation of min and max period. The result in both
divisions is in most cases a truncation to 0, which limits the period to
the range of [0, 0].
Both numerators (and denominators) are within 64 bits, so the whole
expression can be put directly into the div64_u64, instead of doing it
partially.
Fixes: b00d2ed37617 ("leds: rgb: leds-qcom-lpg: Add support for high resolution PWM")
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Lee Jones <lee@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Neil Armstrong <neil.armstrong@linaro.org> # on SM8550-QRD
Link: https://lore.kernel.org/r/20230515162604.649203-1-quic_bjorande@quicinc.com
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- Return NULL if the trace_probe list on trace_probe_event is empty
- selftests/ftrace: Choose testing symbol name for filtering feature
from sample data instead of fixed symbol
* tag 'probes-fixes-6.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
selftests/ftrace: Choose target function for filter test from samples
tracing/probe: trace_probe_primary_from_call(): checked list_first_entry
|
|
Since the event-filter-function.tc expects the 'exit_mmap()' directly
calls 'kmem_cache_free()', this is vulnerable to code modifications.
Choose the target function for the filter test from the sample
event data so that it can keep test running correctly even if the caller
function name will be changed.
Link: https://lore.kernel.org/linux-trace-kernel/167919441260.1922645.18355804179347364057.stgit@mhiramat.roam.corp.google.com/
Link: https://lore.kernel.org/all/CA+G9fYtF-XEKi9YNGgR=Kf==7iRb2FrmEC7qtwAeQbfyah-UhA@mail.gmail.com/
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Fixes: 7f09d639b8c4 ("tracing/selftests: Add test for event filtering on function name")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Keep switching between LAPIC_MODE_X2APIC and LAPIC_MODE_DISABLED during
APIC map construction to hunt for TOCTOU bugs in KVM. KVM's optimized map
recalc makes multiple passes over the list of vCPUs, and the calculations
ignore vCPU's whose APIC is hardware-disabled, i.e. there's a window where
toggling LAPIC_MODE_DISABLED is quite interesting.
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Co-developed-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/20230602233250.1014316-4-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Bail from kvm_recalculate_phys_map() and disable the optimized map if the
target vCPU's x2APIC ID is out-of-bounds, i.e. if the vCPU was added
and/or enabled its local APIC after the map was allocated. This fixes an
out-of-bounds access bug in the !x2apic_format path where KVM would write
beyond the end of phys_map.
Check the x2APIC ID regardless of whether or not x2APIC is enabled,
as KVM's hardcodes x2APIC ID to be the vCPU ID, i.e. it can't change, and
the map allocation in kvm_recalculate_apic_map() doesn't check for x2APIC
being enabled, i.e. the check won't get false postivies.
Note, this also affects the x2apic_format path, which previously just
ignored the "x2apic_id > new->max_apic_id" case. That too is arguably a
bug fix, as ignoring the vCPU meant that KVM would not send interrupts to
the vCPU until the next map recalculation. In practice, that "bug" is
likely benign as a newly present vCPU/APIC would immediately trigger a
recalc. But, there's no functional downside to disabling the map, and
a future patch will gracefully handle the -E2BIG case by retrying instead
of simply disabling the optimized map.
Opportunistically add a sanity check on the xAPIC ID size, along with a
comment explaining why the xAPIC ID is guaranteed to be "good".
Reported-by: Michal Luczaj <mhal@rbox.co>
Fixes: 5b84b0291702 ("KVM: x86: Honor architectural behavior for aliased 8-bit APIC IDs")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230602233250.1014316-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Increment vcpu->stat.exits when handling a fastpath VM-Exit without
going through any part of the "slow" path. Not bumping the exits stat
can result in wildly misleading exit counts, e.g. if the primary reason
the guest is exiting is to program the TSC deadline timer.
Fixes: 404d5d7bff0d ("KVM: X86: Introduce more exit_fastpath_completion enum values")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230602011920.787844-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
While testing Hyper-V enabled Windows Server 2019 guests on Zen4 hardware
I noticed that with vCPU count large enough (> 16) they sometimes froze at
boot.
With vCPU count of 64 they never booted successfully - suggesting some kind
of a race condition.
Since adding "vnmi=0" module parameter made these guests boot successfully
it was clear that the problem is most likely (v)NMI-related.
Running kvm-unit-tests quickly showed failing NMI-related tests cases, like
"multiple nmi" and "pending nmi" from apic-split, x2apic and xapic tests
and the NMI parts of eventinj test.
The issue was that once one NMI was being serviced no other NMI was allowed
to be set pending (NMI limit = 0), which was traced to
svm_is_vnmi_pending() wrongly testing for the "NMI blocked" flag rather
than for the "NMI pending" flag.
Fix this by testing for the right flag in svm_is_vnmi_pending().
Once this is done, the NMI-related kvm-unit-tests pass successfully and
the Windows guest no longer freezes at boot.
Fixes: fa4c027a7956 ("KVM: x86: Add support for SVM's Virtual NMI")
Signed-off-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Link: https://lore.kernel.org/r/be4ca192eb0c1e69a210db3009ca984e6a54ae69.1684495380.git.maciej.szmigiero@oracle.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
Factor in the address space (non-SMM vs. SMM) of the target shadow page
when recovering potential NX huge pages, otherwise KVM will retrieve the
wrong memslot when zapping shadow pages that were created for SMM. The
bug most visibly manifests as a WARN on the memslot being non-NULL, but
the worst case scenario is that KVM could unaccount the shadow page
without ensuring KVM won't install a huge page, i.e. if the non-SMM slot
is being dirty logged, but the SMM slot is not.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 3911 at arch/x86/kvm/mmu/mmu.c:7015
kvm_nx_huge_page_recovery_worker+0x38c/0x3d0 [kvm]
CPU: 1 PID: 3911 Comm: kvm-nx-lpage-re
RIP: 0010:kvm_nx_huge_page_recovery_worker+0x38c/0x3d0 [kvm]
RSP: 0018:ffff99b284f0be68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff99b284edd000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff9271397024e0 R08: 0000000000000000 R09: ffff927139702450
R10: 0000000000000000 R11: 0000000000000001 R12: ffff99b284f0be98
R13: 0000000000000000 R14: ffff9270991fcd80 R15: 0000000000000003
FS: 0000000000000000(0000) GS:ffff927f9f640000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f0aacad3ae0 CR3: 000000088fc2c005 CR4: 00000000003726e0
Call Trace:
<TASK>
__pfx_kvm_nx_huge_page_recovery_worker+0x10/0x10 [kvm]
kvm_vm_worker_thread+0x106/0x1c0 [kvm]
kthread+0xd9/0x100
ret_from_fork+0x2c/0x50
</TASK>
---[ end trace 0000000000000000 ]---
This bug was exposed by commit edbdb43fc96b ("KVM: x86: Preserve TDP MMU
roots until they are explicitly invalidated"), which allowed KVM to retain
SMM TDP MMU roots effectively indefinitely. Before commit edbdb43fc96b,
KVM would zap all SMM TDP MMU roots and thus all SMM TDP MMU shadow pages
once all vCPUs exited SMM, which made the window where this bug (recovering
an SMM NX huge page) could be encountered quite tiny. To hit the bug, the
NX recovery thread would have to run while at least one vCPU was in SMM.
Most VMs typically only use SMM during boot, and so the problematic shadow
pages were gone by the time the NX recovery thread ran.
Now that KVM preserves TDP MMU roots until they are explicitly invalidated
(e.g. by a memslot deletion), the window to trigger the bug is effectively
never closed because most VMMs don't delete memslots after boot (except
for a handful of special scenarios).
Fixes: eb298605705a ("KVM: x86/mmu: Do not recover dirty-tracked NX Huge Pages")
Reported-by: Fabio Coatti <fabio.coatti@gmail.com>
Closes: https://lore.kernel.org/all/CADpTngX9LESCdHVu_2mQkNGena_Ng2CphWNwsRGSMxzDsTjU2A@mail.gmail.com
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230602010137.784664-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
|
|
With commit 858e8b792d06 ("tpm, tpm_tis: Avoid cache incoherency in test
for interrupts") bit accessor functions are used to access flags in
tpm_tis_data->flags.
However these functions expect bit numbers, while the flags are defined
as bit masks in enum tpm_tis_flag.
Fix this inconsistency by using numbers instead of masks also for the
flags in the enum.
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 858e8b792d06 ("tpm, tpm_tis: Avoid cache incoherency in test for interrupts")
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: stable@vger.kernel.org
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fix from Ted Ts'o:
"Fix an ext4 regression which landed during the 6.4 merge window"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
Revert "ext4: remove ac->ac_found > sbi->s_mb_min_to_scan dead check in ext4_mb_check_limits"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One regression fix.
The rewrite of scrub code in 6.4 broke device replace in zoned mode,
some of the writes could happen out of order so this had to be
adjusted for all cases"
* tag 'for-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: zoned: fix dev-replace after the scrub rework
|
|
ext4_mb_check_limits"
This reverts commit 32c0869370194ae5ac9f9f501953ef693040f6a1.
The reverted commit was intended to remove a dead check however it was observed
that this check was actually being used to exit early instead of looping
sbi->s_mb_max_to_scan times when we are able to find a free extent bigger than
the goal extent. Due to this, a my performance tests (fsmark, parallel file
writes in a highly fragmented FS) were seeing a 2x-3x regression.
Example, the default value of the following variables is:
sbi->s_mb_max_to_scan = 200
sbi->s_mb_min_to_scan = 10
In ext4_mb_check_limits() if we find an extent smaller than goal, then we return
early and try again. This loop will go on until we have processed
sbi->s_mb_max_to_scan(=200) number of free extents at which point we exit and
just use whatever we have even if it is smaller than goal extent.
Now, the regression comes when we find an extent bigger than goal. Earlier, in
this case we would loop only sbi->s_mb_min_to_scan(=10) times and then just use
the bigger extent. However with commit 32c08693 that check was removed and hence
we would loop sbi->s_mb_max_to_scan(=200) times even though we have a big enough
free extent to satisfy the request. The only time we would exit early would be
when the free extent is *exactly* the size of our goal, which is pretty uncommon
occurrence and so we would almost always end up looping 200 times.
Hence, revert the commit by adding the check back to fix the regression. Also
add a comment to outline this policy.
Fixes: 32c086937019 ("ext4: remove ac->ac_found > sbi->s_mb_min_to_scan dead check in ext4_mb_check_limits")
Signed-off-by: Ojaswin Mujoo <ojaswin@linux.ibm.com>
Reviewed-by: Ritesh Harjani (IBM) <ritesh.list@gmail.com>
Reviewed-by: Kemeng Shi <shikemeng@huaweicloud.com>
Link: https://lore.kernel.org/r/ddcae9658e46880dfec2fb0aa61d01fb3353d202.1685449706.git.ojaswin@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
When the uvcvideo driver encounters a format descriptor with an unknown
format GUID, it creates a corresponding struct uvc_format instance with
the fcc field set to 0. Since commit 50459f103edf ("media: uvcvideo:
Remove format descriptions"), the driver relies on the V4L2 core to
provide the format description string, which the V4L2 core can't do
without a valid 4CC. This triggers a WARN_ON.
As a format with a zero 4CC can't be selected, it is unusable for
applications. Ignore the format completely without creating a uvc_format
instance, which fixes the warning.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217252
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2180107
Fixes: 50459f103edf ("media: uvcvideo: Remove format descriptions")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A build warning fix for BUILTIN_DTB=y
- Hibernation support is hidden behind NONPORTABLE, as it depends on
some undocumented early boot behavior and breaks on most platforms
- A fix for relocatable kernels on systems with early boot errata
- A fix to properly handle perf callchains for kernel tracepoints
- A pair of fixes for NAPOT to avoid inconsistencies between PTEs and
handle hardware that sets arbitrary A/D bits
* tag 'riscv-for-linus-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Implement missing huge_ptep_get
riscv: Fix huge_ptep_set_wrprotect when PTE is a NAPOT
riscv: perf: Fix callchain parse error with kernel tracepoint events
riscv: Fix relocatable kernels with early alternatives using -fno-pie
RISC-V: mark hibernation as nonportable
riscv: Fix unused variable warning when BUILTIN_DTB is set
|
|
Add missing kernel doc for the new 'client_caps' field in struct
v4l2_subdev_fh.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: f57fa2959244 ("media: v4l2-subdev: Add new ioctl for client capabilities")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Initialize hs_settle to 0 to avoid this compiler warning:
imx8mq-mipi-csi2.c: In function 'imx8mq_mipi_csi_start_stream.part.0':
imx8mq-mipi-csi2.c:91:55: warning: 'hs_settle' may be used uninitialized [-Wmaybe-uninitialized]
91 | #define GPR_CSI2_1_S_PRG_RXHS_SETTLE(x) (((x) & 0x3f) << 2)
| ^~
imx8mq-mipi-csi2.c:357:13: note: 'hs_settle' was declared here
357 | u32 hs_settle;
| ^~~~~~~~~
It's a false positive, but it is too complicated for the compiler to detect that.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
While updating v4l2_create_fwnode_links_to_pad() to accept non-subdev
sinks, the check is_media_entity_v4l2_subdev() was not removed which
prevented the function from being used with non-subdev sinks, Drop the
unnecessary check.
Fixes: bd5a03bc5be8 ("media: Accept non-subdev sinks in v4l2_create_fwnode_links_to_pad()")
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux
Pull nfsd fixes from Chuck Lever:
- Two minor bug fixes
* tag 'nfsd-6.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
nfsd: fix double fget() bug in __write_ports_addfd()
nfsd: make a copy of struct iattr before calling notify_change
|
|
Pull block fixes from Jens Axboe:
"Just an NVMe pull request with (mostly) KATO fixes, a regression fix
for zoned device revalidation, and a fix for an md raid5 regression"
* tag 'block-6.4-2023-06-02' of git://git.kernel.dk/linux:
nvme: fix the name of Zone Append for verbose logging
nvme: improve handling of long keep alives
nvme: check IO start time when deciding to defer KA
nvme: double KA polling frequency to avoid KATO with TBKAS on
nvme: fix miss command type check
block: fix revalidate performance regression
md/raid5: fix miscalculation of 'end_sector' in raid5_read_one_chunk()
|
|
Pull io_uring fix from Jens Axboe:
"Just a single revert in here, removing the warning on the epoll ctl
opcode.
We originally deprecated this a few releases ago, but I've since had
two people report that it's being used. Which isn't the biggest deal,
obviously this is why we out in the deprecation notice in the first
place, but it also means that we should just kill this warning again
and abandon the deprecation plans.
Since it's only a few handfuls of code to support epoll ctl, not worth
going any further with this imho"
* tag 'io_uring-6.4-2023-06-02' of git://git.kernel.dk/linux:
io_uring: undeprecate epoll_ctl support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix pwrseq for WILC1000/WILC3000 SDIO card
MMC host:
- vub300: Fix invalid response handling"
* tag 'mmc-v6.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: pwrseq: sd8787: Fix WILC CHIP_EN and RESETN toggling order
mmc: vub300: fix invalid response handling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
"AMD IOMMU fixes:
- Fix domain type and size checks
- IOTLB flush fix for invalidating ranges
- Guest IRQ handling fixes and GALOG overflow fix
Rockchip IOMMU:
- Error handling fix
Mediatek IOMMU:
- IOTLB flushing fix
Renesas IOMMU:
- Fix Kconfig dependencies to avoid build errors on RiscV"
* tag 'iommu-fixes-v6.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/mediatek: Flush IOTLB completely only if domain has been attached
iommu/amd/pgtbl_v2: Fix domain max address
iommu/amd: Fix domain flush size when syncing iotlb
iommu/amd: Add missing domain type checks
iommu/amd: Fix up merge conflict resolution
iommu/amd: Handle GALog overflows
iommu/amd: Don't block updates to GATag if guest mode is on
iommu/rockchip: Fix unwind goto issue
iommu: Make IPMMU_VMSA dependencies more strict
|
|
Pull drm fixes from Dave Airlie:
"Quiet enough week, though the misc fixes tree didn't get to me when I
was sending this, so maybe it'll be a bit bigger next week, just one
i915 fix and some scattered amdgpu fixes:
amdgpu:
- Fix mclk and fclk output ordering on some APUs
- Fix display regression with 5K VRR
- VCN, JPEG spurious interrupt warning fixes
- Fix SI DPM on some ARM64 platforms
- Fix missing TMZ enablement on GC 11.0.1
i915:
- Fix for OA reporting to allow detecting non-power-of-two reports"
* tag 'drm-fixes-2023-06-02' of git://anongit.freedesktop.org/drm/drm:
drm/i915/perf: Clear out entire reports after reading if not power of 2 size
drm/amdgpu: enable tmz by default for GC 11.0.1
drm/amd/pm: resolve reboot exception for si oland
drm/amdgpu: add RAS POISON interrupt funcs for jpeg_v4_0
drm/amdgpu: add RAS POISON interrupt funcs for jpeg_v2_6
drm/amdgpu: separate ras irq from jpeg instance irq for UVD_POISON
drm/amdgpu: add RAS POISON interrupt funcs for vcn_v4_0
drm/amdgpu: add RAS POISON interrupt funcs for vcn_v2_6
drm/amdgpu: separate ras irq from vcn instance irq for UVD_POISON
Revert "drm/amd/display: Do not set drr on pipe commit"
Revert "drm/amd/display: Block optimize on consecutive FAMS enables"
drm/amd/pm: reverse mclk and fclk clocks levels for renoir
drm/amd/pm: reverse mclk and fclk clocks levels for vangogh
drm/amd/pm: reverse mclk and fclk clocks levels for yellow carp
drm/amd/pm: reverse mclk clocks levels for SMU v13.0.5
drm/amd/pm: reverse mclk and fclk clocks levels for SMU v13.0.4
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux
Pull selinux fix from Paul Moore:
"A small SELinux Makefile fix to resolve a problem seen when building
the kernel with older versions of make.
The fix is pretty trivial and effectively reverts a patch that was
merged during the last merge window"
* tag 'selinux-pr-20230601' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
selinux: don't use make's grouped targets feature yet
|
|
huge_ptep_get must be reimplemented in order to go through all the PTEs
of a NAPOT region: this is needed because the HW can update the A/D bits
of any of the PTE that constitutes the NAPOT region.
Fixes: 82a1a1f3bfb6 ("riscv: mm: support Svnapot in hugetlb page")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20230428120120.21620-2-alexghiti@rivosinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
We need to avoid inconsistencies across the PTEs that form a NAPOT
region, so when we write protect such a region, we should clear and flush
all the PTEs to make sure that any of those PTEs is not cached which would
result in such inconsistencies (arm64 does the same).
Fixes: 82a1a1f3bfb6 ("riscv: mm: support Svnapot in hugetlb page")
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Link: https://lore.kernel.org/r/20230428120120.21620-1-alexghiti@rivosinc.com
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull modules fix from Luis Chamberlain:
"A zstd fix by lucas as he tested zstd decompression support"
* tag 'modules-6.4-rc5-second-pull' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module/decompress: Fix error checking on zstd decompression
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
"A few minor fixes for EFI, one of which fixes the reported boot
regression when booting x86 kernels using the BIOS based loader built
into the hypervisor framework on macOS.
- fix harmless warning in zboot code on 'make clean'
- add some missing prototypes
- fix boot regressions triggered by PE/COFF header image minor
version bump"
* tag 'efi-fixes-for-v6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: Bump stub image version for macOS HVF compatibility
efi: fix missing prototype warnings
efi/libstub: zboot: Avoid eager evaluation of objcopy flags
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Fix for OA reporting to allow detecting non-power-of-two reports
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZHimf55x/DyXYar1@jlahtine-mobl.ger.corp.intel.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.4-2023-05-31:
amdgpu:
- Fix mclk and fclk output ordering on some APUs
- Fix display regression with 5K VRR
- VCN, JPEG spurious interrupt warning fixes
- Fix SI DPM on some ARM64 platforms
- Fix missing TMZ enablement on GC 11.0.1
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230601033846.7628-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev fixes from Helge Deller:
"Most notable is a fix for a null-ptr-deref in fbcon's soft_cursor
function which was found by syzbot.
- Fix null-ptr-deref in soft_cursor
- various remove callback conversions
- error path fixes in imsttfb"
* tag 'fbdev-for-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev:
fbdev: bw2: Convert to platform remove callback returning void
fbdev: broadsheetfb: Convert to platform remove callback returning void
fbdev: au1200fb: Convert to platform remove callback returning void
fbdev: au1100fb: Convert to platform remove callback returning void
fbdev: arcfb: Convert to platform remove callback returning void
fbdev: au1100fb: Drop if with an always false condition
fbcon: Fix null-ptr-deref in soft_cursor
fbdev: imsttfb: Fix error path of imsttfb_probe()
fbdev: imsttfb: Release framebuffer and dealloc cmap on error path
fbdev: matroxfb ssd1307fb: Switch i2c drivers back to use .probe()
|
|
While implementing support for in-kernel decompression in kmod,
finit_module() was returning a very suspicious value:
finit_module(3, "", MODULE_INIT_COMPRESSED_FILE) = 18446744072717407296
It turns out the check for module_get_next_page() failing is wrong,
and hence the decompression was not really taking place. Invert
the condition to fix it.
Fixes: 169a58ad824d ("module/decompress: Support zstd in-kernel decompression")
Cc: stable@kernel.org
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fixes from Miquel Raynal:
"MTD core:
- MAINTAINERS: Add Michal as reviewer instead of Naga
- mtdchar: Mark bits of ioctl handler noinline
NAND controller drivers:
- marvell:
- Don't set the NAND frequency select
- Ensure timing values are written
- ingenic: Fix empty stub helper definitions
SPI-NOR core:
- Fix divide by zero for spi-nor-generic flashes
SPI-NOR manufacturer driver:
- spansion: make sure local struct does not contain garbage"
* tag 'mtd/fixes-for-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: don't set the NAND frequency select
mtd: rawnand: marvell: ensure timing values are written
mtdchar: mark bits of ioctl handler noinline
MAINTAINERS: Add myself as reviewer instead of Naga
mtd: spi-nor: Fix divide by zero for spi-nor-generic flashes
mtd: rawnand: ingenic: fix empty stub helper definitions
mtd: spi-nor: spansion: make sure local struct does not contain garbage
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Happy Wear a Dress Day.
Fairly standard-sized batch of fixes, accounting for the lack of
sub-tree submissions this week. The mlx5 IRQ fixes are notable, people
were complaining about that. No fires burning.
Current release - regressions:
- eth: mlx5e:
- multiple fixes for dynamic IRQ allocation
- prevent encap offload when neigh update is running
- eth: mana: fix perf regression: remove rx_cqes, tx_cqes counters
Current release - new code bugs:
- eth: mlx5e: DR, add missing mutex init/destroy in pattern manager
Previous releases - always broken:
- tcp: deny tcp_disconnect() when threads are waiting
- sched: prevent ingress Qdiscs from getting installed in random
locations in the hierarchy and moving around
- sched: flower: fix possible OOB write in fl_set_geneve_opt()
- netlink: fix NETLINK_LIST_MEMBERSHIPS length report
- udp6: fix race condition in udp6_sendmsg & connect
- tcp: fix mishandling when the sack compression is deferred
- rtnetlink: validate link attributes set at creation time
- mptcp: fix connect timeout handling
- eth: stmmac: fix call trace when stmmac_xdp_xmit() is invoked
- eth: amd-xgbe: fix the false linkup in xgbe_phy_status
- eth: mlx5e:
- fix corner cases in internal buffer configuration
- drain health before unregistering devlink
- usb: qmi_wwan: set DTR quirk for BroadMobi BM818
Misc:
- tcp: return user_mss for TCP_MAXSEG in CLOSE/LISTEN state if
user_mss set"
* tag 'net-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
mptcp: fix active subflow finalization
mptcp: add annotations around sk->sk_shutdown accesses
mptcp: fix data race around msk->first access
mptcp: consolidate passive msk socket initialization
mptcp: add annotations around msk->subflow accesses
mptcp: fix connect timeout handling
rtnetlink: add the missing IFLA_GRO_ tb check in validate_linkmsg
rtnetlink: move IFLA_GSO_ tb check to validate_linkmsg
rtnetlink: call validate_linkmsg in rtnl_create_link
ice: recycle/free all of the fragments from multi-buffer frame
net: phy: mxl-gpy: extend interrupt fix to all impacted variants
net: renesas: rswitch: Fix return value in error path of xmit
net: dsa: mv88e6xxx: Increase wait after reset deactivation
net: ipa: Use correct value for IPA_STATUS_SIZE
tcp: fix mishandling when the sack compression is deferred.
net/sched: flower: fix possible OOB write in fl_set_geneve_opt()
sfc: fix error unwinds in TC offload
net/mlx5: Read embedded cpu after init bit cleared
net/mlx5e: Fix error handling in mlx5e_refresh_tirs
net/mlx5: Ensure af_desc.mask is properly initialized
...
|
|
When switching from kthreads to vhost_tasks two bugs were added:
1. The vhost worker tasks's now show up as processes so scripts doing
ps or ps a would not incorrectly detect the vhost task as another
process. 2. kthreads disabled freeze by setting PF_NOFREEZE, but
vhost tasks's didn't disable or add support for them.
To fix both bugs, this switches the vhost task to be thread in the
process that does the VHOST_SET_OWNER ioctl, and has vhost_worker call
get_signal to support SIGKILL/SIGSTOP and freeze signals. Note that
SIGKILL/STOP support is required because CLONE_THREAD requires
CLONE_SIGHAND which requires those 2 signals to be supported.
This is a modified version of the patch written by Mike Christie
<michael.christie@oracle.com> which was a modified version of patch
originally written by Linus.
Much of what depended upon PF_IO_WORKER now depends on PF_USER_WORKER.
Including ignoring signals, setting up the register state, and having
get_signal return instead of calling do_group_exit.
Tidied up the vhost_task abstraction so that the definition of
vhost_task only needs to be visible inside of vhost_task.c. Making
it easier to review the code and tell what needs to be done where.
As part of this the main loop has been moved from vhost_worker into
vhost_task_fn. vhost_worker now returns true if work was done.
The main loop has been updated to call get_signal which handles
SIGSTOP, freezing, and collects the message that tells the thread to
exit as part of process exit. This collection clears
__fatal_signal_pending. This collection is not guaranteed to
clear signal_pending() so clear that explicitly so the schedule()
sleeps.
For now the vhost thread continues to exist and run work until the
last file descriptor is closed and the release function is called as
part of freeing struct file. To avoid hangs in the coredump
rendezvous and when killing threads in a multi-threaded exec. The
coredump code and de_thread have been modified to ignore vhost threads.
Remvoing the special case for exec appears to require teaching
vhost_dev_flush how to directly complete transactions in case
the vhost thread is no longer running.
Removing the special case for coredump rendezvous requires either the
above fix needed for exec or moving the coredump rendezvous into
get_signal.
Fixes: 6e890c5d5021 ("vhost: use vhost_tasks for worker threads")
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Co-developed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add rs485-rts-active-high property, this was removed by mistake.
In general we just use rs485-rts-active-low property, however the OMAP
UART for legacy reason uses the -high one.
Fixes: 767d3467eb60 ("dt-bindings: serial: 8250_omap: drop rs485 properties")
Closes: https://lore.kernel.org/all/ZGefR4mTHHo1iQ7H@francesco-nb.int.toradex.com/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230531111038.6302-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use grep instead of sed for all compiled sources generation, it is three
times more efficient.
Signed-off-by: Jialu Xu <xujialu@vimux.org>
Tested-by: Carlos Llamas <cmllamas@google.com>
Link: https://lore.kernel.org/r/20230601010402.71040-1-xujialu@vimux.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Linux Kernel currently only requires make v3.82 while the grouped
target functionality requires make v4.3. Removed the grouped target
introduced in 4ce1f694eb5d ("selinux: ensure av_permissions.h is
built when needed") as well as the multiple header file targets in
the make rule. This effectively reverts the problem commit.
We will revisit this change when make >= 4.3 is required by the rest
of the kernel.
Cc: stable@vger.kernel.org
Fixes: 4ce1f694eb5d ("selinux: ensure av_permissions.h is built when needed")
Reported-by: Erwan Velu <e.velu@criteo.com>
Reported-by: Luiz Capitulino <luizcap@amazon.com>
Tested-by: Luiz Capitulino <luizcap@amazon.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-w1 into char-misc-next
Krzysztof writes:
1-Wire bus drivers for v6.5
1. Several older cleanups and minor improvements like dropping redundant
match function, fixing indentation and typos, simplifying sysfs
attribute show, removing redundant variable initializations, using max()
instead of open-coding it and constifying pointer to
struct hwmon_channel_info.
2. w1_therm: fix inverted lock handling causing spurious temperature
reads.
3. sgi: Use strscpy() over strlcpy().
4. w1 bus fixes:
- Correct missing OF node reference put in error path.
- Correct iterating over master device list while removing items from
it.
- Don't use loop iterator past the loop.
* tag 'w1-drv-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-w1:
w1: Replace usage of found with dedicated list iterator variable
w1: therm: constify pointers to hwmon_channel_info
w1: Add missing of_node_put() in w1.c
w1: no need to initialise statics to 0
w1: ds2438: remove redundant initialization of variable crc
w1: w1_therm: fix typo in comment
w1: w1_therm: Use max() instead of doing it manually
w1: fix loop in w1_fini()
w1: remove redundant initialization to variable result
w1: Simplify the atribute show
w1: Fix Kconfig indentation
w1: sgi: move from strlcpy with unused retval to strscpy
w1: Remove driver match function
w1: w1_therm: fix locking behavior in convert_t
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-05-31
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Read embedded cpu after init bit cleared
net/mlx5e: Fix error handling in mlx5e_refresh_tirs
net/mlx5: Ensure af_desc.mask is properly initialized
net/mlx5: Fix setting of irq->map.index for static IRQ case
net/mlx5: Remove rmap also in case dynamic MSIX not supported
====================
Link: https://lore.kernel.org/r/20230601031051.131529-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull NVMe fixes from Keith:
"nvme fixes for Linux 6.4
- Fixes for spurious Keep Alive timeouts (Uday)
- Fix for command type check on passthrough actions (Min)
- Fix for nvme command name for error logging (Christoph)"
* tag 'nvme-6.4-2023-06-01' of git://git.infradead.org/nvme:
nvme: fix the name of Zone Append for verbose logging
nvme: improve handling of long keep alives
nvme: check IO start time when deciding to defer KA
nvme: double KA polling frequency to avoid KATO with TBKAS on
nvme: fix miss command type check
|
|
For RISC-V, when tracing with tracepoint events, the IP and status are
set to 0, preventing the perf code parsing the callchain and resolving
the symbols correctly.
./ply 'tracepoint:kmem/kmem_cache_alloc { @[stack]=count(); }'
@:
{ <STACKID4294967282> }: 1
The fix is to implement perf_arch_fetch_caller_regs for riscv, which
fills several necessary registers used for callchain unwinding,
including epc, sp, s0 and status. It's similar to commit b3eac0265bf6
("arm: perf: Fix callchain parse error with kernel tracepoint events")
and commit 5b09a094f2fb ("arm64: perf: Fix callchain parse error with
kernel tracepoint events").
With this patch, callchain can be parsed correctly as:
./ply 'tracepoint:kmem/kmem_cache_alloc { @[stack]=count(); }'
@:
{
__traceiter_kmem_cache_alloc+68
__traceiter_kmem_cache_alloc+68
kmem_cache_alloc+354
__sigqueue_alloc+94
__send_signal_locked+646
send_signal_locked+154
do_send_sig_info+84
__kill_pgrp_info+130
kill_pgrp+60
isig+150
n_tty_receive_signal_char+36
n_tty_receive_buf_standard+2214
n_tty_receive_buf_common+280
n_tty_receive_buf2+26
tty_ldisc_receive_buf+34
tty_port_default_receive_buf+62
flush_to_ldisc+158
process_one_work+458
worker_thread+138
kthread+178
riscv_cpufeature_patch_func+832
}: 1
Signed-off-by: Ism Hong <ism.hong@gmail.com>
Link: https://lore.kernel.org/r/20230601095355.1168910-1-ism.hong@gmail.com
Fixes: 178e9fc47aae ("perf: riscv: preliminary RISC-V support")
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
'mptcp-fixes-for-connect-timeout-access-annotations-and-subflow-init'
Mat Martineau says:
====================
mptcp: Fixes for connect timeout, access annotations, and subflow init
Patch 1 allows the SO_SNDTIMEO sockopt to correctly change the connect
timeout on MPTCP sockets.
Patches 2-5 add READ_ONCE()/WRITE_ONCE() annotations to fix KCSAN issues.
Patch 6 correctly initializes some subflow fields on outgoing connections.
====================
Link: https://lore.kernel.org/r/20230531-send-net-20230531-v1-0-47750c420571@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Active subflow are inserted into the connection list at creation time.
When the MPJ handshake completes successfully, a new subflow creation
netlink event is generated correctly, but the current code wrongly
avoid initializing a couple of subflow data.
The above will cause misbehavior on a few exceptional events: unneeded
mptcp-level retransmission on msk-level sequence wrap-around and infinite
mapping fallback even when a MPJ socket is present.
Address the issue factoring out the needed initialization in a new helper
and invoking the latter from __mptcp_finish_join() time for passive
subflow and from mptcp_finish_join() for active ones.
Fixes: 0530020a7c8f ("mptcp: track and update contiguous data status")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Christoph reported the mptcp variant of a recently addressed plain
TCP issue. Similar to commit e14cadfd80d7 ("tcp: add annotations around
sk->sk_shutdown accesses") add READ/WRITE ONCE annotations to silence
KCSAN reports around lockless sk_shutdown access.
Fixes: 71ba088ce0aa ("mptcp: cleanup accept and poll")
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/401
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The first subflow socket is accessed outside the msk socket lock
by mptcp_subflow_fail(), we need to annotate each write access
with WRITE_ONCE, but a few spots still lacks it.
Fixes: 76a13b315709 ("mptcp: invoke MP_FAIL response when needed")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the msk socket is cloned at MPC handshake time, a few
fields are initialized in a racy way outside mptcp_sk_clone()
and the msk socket lock.
The above is due historical reasons: before commit a88d0092b24b
("mptcp: simplify subflow_syn_recv_sock()") as the first subflow socket
carrying all the needed date was not available yet at msk creation
time
We can now refactor the code moving the missing initialization bit
under the socket lock, removing the init race and avoiding some
code duplication.
This will also simplify the next patch, as all msk->first write
access are now under the msk socket lock.
Fixes: 0397c6d85f9c ("mptcp: keep unaccepted MPC subflow into join list")
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MPTCP can access the first subflow socket in a few spots
outside the socket lock scope. That is actually safe, as MPTCP
will delete the socket itself only after the msk sock close().
Still the such accesses causes a few KCSAN splats, as reported
by Christoph. Silence the harmless warning adding a few annotation
around the relevant accesses.
Fixes: 71ba088ce0aa ("mptcp: cleanup accept and poll")
Reported-by: Christoph Paasch <cpaasch@apple.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/402
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ondrej reported a functional issue WRT timeout handling on connect
with a nice reproducer.
The problem is that the current mptcp connect waits for both the
MPTCP socket level timeout, and the first subflow socket timeout.
The latter is not influenced/touched by the exposed setsockopt().
Overall the above makes the SO_SNDTIMEO a no-op on connect.
Since mptcp_connect is invoked via inet_stream_connect and the
latter properly handle the MPTCP level timeout, we can address the
issue making the nested subflow level connect always unblocking.
This also allow simplifying a bit the code, dropping an ugly hack
to handle the fastopen and custom proto_ops connect.
The issues predates the blamed commit below, but the current resolution
requires the infrastructure introduced there.
Fixes: 54f1944ed6d2 ("mptcp: factor out mptcp_connect()")
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/399
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Xin Long says:
====================
rtnetlink: a couple of fixes in linkmsg validation
validate_linkmsg() was introduced to do linkmsg validation for existing
links. However, the new created links also need this linkmsg validation.
Add validate_linkmsg() check for link creating in Patch 1, and add more
tb checks into validate_linkmsg() in Patch 2 and 3.
====================
Link: https://lore.kernel.org/r/cover.1685548598.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This fixes the issue that dev gro_max_size and gso_ipv4_max_size
can be set to a huge value:
# ip link add dummy1 type dummy
# ip link set dummy1 gro_max_size 4294967295
# ip -d link show dummy1
dummy addrgenmode eui64 ... gro_max_size 4294967295
Fixes: 0fe79f28bfaf ("net: allow gro_max_size to exceed 65536")
Fixes: 9eefedd58ae1 ("net: add gso_ipv4_max_size and gro_ipv4_max_size per device")
Reported-by: Xiumei Mu <xmu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These IFLA_GSO_* tb check should also be done for the new created link,
otherwise, they can be set to a huge value when creating links:
# ip link add dummy1 gso_max_size 4294967295 type dummy
# ip -d link show dummy1
dummy addrgenmode eui64 ... gso_max_size 4294967295
Fixes: 46e6b992c250 ("rtnetlink: allow GSO maximums to be set on device creation")
Fixes: 9eefedd58ae1 ("net: add gso_ipv4_max_size and gro_ipv4_max_size per device")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
validate_linkmsg() was introduced by commit 1840bb13c22f5b ("[RTNL]:
Validate hardware and broadcast address attribute for RTM_NEWLINK")
to validate tb[IFLA_ADDRESS/BROADCAST] for existing links. The same
check should also be done for newly created links.
This patch adds validate_linkmsg() call in rtnl_create_link(), to
avoid the invalid address set when creating some devices like:
# ip link add dummy0 type dummy
# ip link add link dummy0 name mac0 address 01:02 type macsec
Fixes: 0e06877c6fdb ("[RTNETLINK]: rtnl_link: allow specifying initial device address")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ice driver caches next_to_clean value at the beginning of
ice_clean_rx_irq() in order to remember the first buffer that has to be
freed/recycled after main Rx processing loop. The end boundary is
indicated by first descriptor of frame that Rx processing loop has ended
its duties. Note that if mentioned loop ended in the middle of gathering
multi-buffer frame, next_to_clean would be pointing to the descriptor in
the middle of the frame BUT freeing/recycling stage will stop at the
first descriptor. This means that next iteration of ice_clean_rx_irq()
will miss the (first_desc, next_to_clean - 1) entries.
When running various 9K MTU workloads, such splats were observed:
[ 540.780716] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 540.787787] #PF: supervisor read access in kernel mode
[ 540.793002] #PF: error_code(0x0000) - not-present page
[ 540.798218] PGD 0 P4D 0
[ 540.800801] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 540.805231] CPU: 18 PID: 3984 Comm: xskxceiver Tainted: G W 6.3.0-rc7+ #96
[ 540.813619] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 540.824209] RIP: 0010:ice_clean_rx_irq+0x2b6/0xf00 [ice]
[ 540.829678] Code: 74 24 10 e9 aa 00 00 00 8b 55 78 41 31 57 10 41 09 c4 4d 85 ff 0f 84 83 00 00 00 49 8b 57 08 41 8b 4f 1c 65 8b 35 1a fa 4b 3f <48> 8b 02 48 c1 e8 3a 39 c6 0f 85 a2 00 00 00 f6 42 08 02 0f 85 98
[ 540.848717] RSP: 0018:ffffc9000f42fc50 EFLAGS: 00010282
[ 540.854029] RAX: 0000000000000004 RBX: 0000000000000002 RCX: 000000000000fffe
[ 540.861272] RDX: 0000000000000000 RSI: 0000000000000001 RDI: 00000000ffffffff
[ 540.868519] RBP: ffff88984a05ac00 R08: 0000000000000000 R09: dead000000000100
[ 540.875760] R10: ffff88983fffcd00 R11: 000000000010f2b8 R12: 0000000000000004
[ 540.883008] R13: 0000000000000003 R14: 0000000000000800 R15: ffff889847a10040
[ 540.890253] FS: 00007f6ddf7fe640(0000) GS:ffff88afdf800000(0000) knlGS:0000000000000000
[ 540.898465] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 540.904299] CR2: 0000000000000000 CR3: 000000010d3da001 CR4: 00000000007706e0
[ 540.911542] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 540.918789] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 540.926032] PKRU: 55555554
[ 540.928790] Call Trace:
[ 540.931276] <TASK>
[ 540.933418] ice_napi_poll+0x4ca/0x6d0 [ice]
[ 540.937804] ? __pfx_ice_napi_poll+0x10/0x10 [ice]
[ 540.942716] napi_busy_loop+0xd7/0x320
[ 540.946537] xsk_recvmsg+0x143/0x170
[ 540.950178] sock_recvmsg+0x99/0xa0
[ 540.953729] __sys_recvfrom+0xa8/0x120
[ 540.957543] ? do_futex+0xbd/0x1d0
[ 540.961008] ? __x64_sys_futex+0x73/0x1d0
[ 540.965083] __x64_sys_recvfrom+0x20/0x30
[ 540.969155] do_syscall_64+0x38/0x90
[ 540.972796] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 540.977934] RIP: 0033:0x7f6de5f27934
To fix this, set cached_ntc to first_desc so that at the end, when
freeing/recycling buffers, descriptors from first to ntc are not missed.
Fixes: 2fba7dc5157b ("ice: Add support for XDP multi-buffer on Rx side")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230531154457.3216621-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The interrupt fix in commit 97a89ed101bb should be applied on all variants
of GPY2xx PHY and GPY115C.
Fixes: 97a89ed101bb ("net: phy: mxl-gpy: disable interrupts on GPY215 by default")
Signed-off-by: Xu Liang <lxu@maxlinear.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230531074822.39136-1-lxu@maxlinear.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix return value in the error path of rswitch_start_xmit(). If TX
queues are full, this function should return NETDEV_TX_BUSY.
Fixes: 3590918b5d07 ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20230529073817.1145208-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-2-chris.packham@alliedtelesis.co.nz
|
|
When new timing values are calculated in marvell_nfc_setup_interface()
ensure that they will be applied in marvell_nfc_select_target() by
clearing the selected_chip pointer.
Fixes: b25251414f6e ("mtd: rawnand: marvell: Stop implementing ->select_chip()")
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230525003154.2303012-1-chris.packham@alliedtelesis.co.nz
|
|
The addition of the mtdchar_read_ioctl() function caused the stack usage
of mtdchar_ioctl() to grow beyond the warning limit on 32-bit architectures
with gcc-13:
drivers/mtd/mtdchar.c: In function 'mtdchar_ioctl':
drivers/mtd/mtdchar.c:1229:1: error: the frame size of 1488 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Mark both the read and write portions as noinline_for_stack to ensure
they don't get inlined and use separate stack slots to reduce the
maximum usage, both in the mtdchar_ioctl() and combined with any
of its callees.
Fixes: 095bb6e44eb1 ("mtdchar: add MEMREAD ioctl")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230417205654.1982368-1-arnd@kernel.org
|
|
Naga no longer works for AMD/Xilinx and there is no activity from him to
continue to maintain Xilinx related drivers. Add myself instead to be kept
in loop if there is any need for testing.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[<miquel.raynal@bootlin.com>: Manually apply on top of the latest -rc which
where the MAINTAINERS file got sorted]
Link: https://lore.kernel.org/linux-mtd/06df49c300c53a27423260e99acc217b06d4e588.1684827820.git.michal.simek@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Takashi Sakamoto:
"A single patch to use a flexible array rather than a zero-length one"
* tag 'firewire-fixes-6.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: Replace zero-length array with flexible-array member
|
|
git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox fix from Jassi Brar:
"Fix missing mutex unlock in mailbox-test"
* tag 'mailbox-fixes-6.4-rc5' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: mailbox-test: fix a locking issue in mbox_test_message_write()
|
|
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation")
Signed-off-by: Andreas Svensson <andreas.svensson@axis.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Zero-length and one-element arrays are deprecated, and we are moving
towards adopting C99 flexible-array members, instead.
Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
sound/firewire/amdtp-stream.c: In function ‘build_it_pkt_header’:
sound/firewire/amdtp-stream.c:694:17: warning: ‘generate_cip_header’ accessing 8 bytes in a region of size 0 [-Wstringop-overflow=]
694 | generate_cip_header(s, cip_header, data_block_counter, syt);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sound/firewire/amdtp-stream.c:694:17: note: referencing argument 2 of type ‘__be32[2]’ {aka ‘unsigned int[2]’}
sound/firewire/amdtp-stream.c:667:13: note: in a call to function ‘generate_cip_header’
667 | static void generate_cip_header(struct amdtp_stream *s, __be32 cip_header[2],
| ^~~~~~~~~~~~~~~~~~~
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/303
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/ZHT0V3SpvHyxCv5W@work
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
|
|
[BUG]
After commit e02ee89baa66 ("btrfs: scrub: switch scrub_simple_mirror()
to scrub_stripe infrastructure"), scrub no longer works for zoned device
at all.
Even an empty zoned btrfs cannot be replaced:
# mkfs.btrfs -f /dev/nvme0n1
# mount /dev/nvme0n1 /mnt/btrfs
# btrfs replace start -Bf 1 /dev/nvme0n2 /mnt/btrfs
Resetting device zones /dev/nvme1n1 (160 zones) ...
ERROR: ioctl(DEV_REPLACE_START) failed on "/mnt/btrfs/": Input/output error
And we can hit kernel crash related to that:
BTRFS info (device nvme1n1): host-managed zoned block device /dev/nvme3n1, 160 zones of 134217728 bytes
BTRFS info (device nvme1n1): dev_replace from /dev/nvme2n1 (devid 2) to /dev/nvme3n1 started
nvme3n1: Zone Management Append(0x7d) @ LBA 65536, 4 blocks, Zone Is Full (sct 0x1 / sc 0xb9) DNR
I/O error, dev nvme3n1, sector 786432 op 0xd:(ZONE_APPEND) flags 0x4000 phys_seg 3 prio class 2
BTRFS error (device nvme1n1): bdev /dev/nvme3n1 errs: wr 1, rd 0, flush 0, corrupt 0, gen 0
BUG: kernel NULL pointer dereference, address: 00000000000000a8
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
RIP: 0010:_raw_spin_lock_irqsave+0x1e/0x40
Call Trace:
<IRQ>
btrfs_lookup_ordered_extent+0x31/0x190
btrfs_record_physical_zoned+0x18/0x40
btrfs_simple_end_io+0xaf/0xc0
blk_update_request+0x153/0x4c0
blk_mq_end_request+0x15/0xd0
nvme_poll_cq+0x1d3/0x360
nvme_irq+0x39/0x80
__handle_irq_event_percpu+0x3b/0x190
handle_irq_event+0x2f/0x70
handle_edge_irq+0x7c/0x210
__common_interrupt+0x34/0xa0
common_interrupt+0x7d/0xa0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
[CAUSE]
Dev-replace reuses scrub code to iterate all extents and write the
existing content back to the new device.
And for zoned devices, we call fill_writer_pointer_gap() to make sure
all the writes into the zoned device is sequential, even if there may be
some gaps between the writes.
However we have several different bugs all related to zoned dev-replace:
- We are using ZONE_APPEND operation for metadata style write back
For zoned devices, btrfs has two ways to write data:
* ZONE_APPEND for data
This allows higher queue depth, but will not be able to know where
the write would land.
Thus needs to grab the real on-disk physical location in it's endio.
* WRITE for metadata
This requires single queue depth (new writes can only be submitted
after previous one finished), and all writes must be sequential.
For scrub, we go single queue depth, but still goes with ZONE_APPEND,
which requires btrfs_bio::inode being populated.
This is the cause of that crash.
- No correct tracing of write_pointer
After a write finished, we should forward sctx->write_pointer, or
fill_writer_pointer_gap() would not work properly and cause more
than necessary zero out, and fill the whole zone prematurely.
- Incorrect physical bytenr passed to fill_writer_pointer_gap()
In scrub_write_sectors(), one call site passes logical address, which
is completely wrong.
The other call site passes physical address of current sector, but
we should pass the physical address of the btrfs_bio we're submitting.
This is the cause of the -EIO errors.
[FIX]
- Do not use ZONE_APPEND for btrfs_submit_repair_write().
- Manually forward sctx->write_pointer after successful writeback
- Use the physical address of the to-be-submitted btrfs_bio for
fill_writer_pointer_gap()
Now zoned device replace would work as expected.
Reported-by: Christoph Hellwig <hch@lst.de>
Fixes: e02ee89baa66 ("btrfs: scrub: switch scrub_simple_mirror() to scrub_stripe infrastructure")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid
Pull HID fixes from Jiri Kosina:
- Regression fix for overlong long timeouts during initialization on
some Logitech Unifying devices (Bastien Nocera)
- error handling and overflow fixes for Wacom driver (Denis Arefev,
Jason Gerecke, Nikita Zhandarovich)
* tag 'for-linus-2023060101' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
HID: logitech-hidpp: Handle timeout differently from busy
HID: wacom: Add error check to wacom_parse_and_register()
HID: google: add jewel USB id
HID: wacom: avoid integer overflow in wacom_intuos_inout()
HID: wacom: Check for string overflow from strscpy calls
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fix from Damien Le Moal:
- Fix ata_find_dev() use of the device number to find a struct
ata_device for a port. This addresses issues with some passthrough
commands with libsas managed devices.
* tag 'ata-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-scsi: Use correct device no in ata_find_dev()
|
|
Pull smb server fixes from Steve French:
"Eight server fixes (most also for stable):
- Two fixes for uninitialized pointer reads (rename and link)
- Fix potential UAF in oplock break
- Two fixes for potential out of bound reads in negotiate
- Fix crediting bug
- Two fixes for xfstests (allocation size fix for test 694 and lookup
issue shown by test 464)"
* tag '6.4-rc4-smb3-server-fixes' of git://git.samba.org/ksmbd:
ksmbd: call putname after using the last component
ksmbd: fix incorrect AllocationSize set in smb2_get_info
ksmbd: fix UAF issue from opinfo->conn
ksmbd: fix multiple out-of-bounds read during context decoding
ksmbd: fix slab-out-of-bounds read in smb2_handle_negotiate
ksmbd: fix credit count leakage
ksmbd: fix uninitialized pointer read in smb2_create_link()
ksmbd: fix uninitialized pointer read in ksmbd_vfs_rename()
|
|
IPA_STATUS_SIZE was introduced in commit b8dc7d0eea5a as a replacement
for the size of the removed struct ipa_status which had size
sizeof(__le32[8]). Use this value as IPA_STATUS_SIZE.
Fixes: b8dc7d0eea5a ("net: ipa: stop using sizeof(status)")
Signed-off-by: Bert Karwatzki <spasswolf@web.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230531103618.102608-1-spasswolf@web.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In this patch, we mainly try to handle sending a compressed ack
correctly if it's deferred.
Here are more details in the old logic:
When sack compression is triggered in the tcp_compressed_ack_kick(),
if the sock is owned by user, it will set TCP_DELACK_TIMER_DEFERRED
and then defer to the release cb phrase. Later once user releases
the sock, tcp_delack_timer_handler() should send a ack as expected,
which, however, cannot happen due to lack of ICSK_ACK_TIMER flag.
Therefore, the receiver would not sent an ack until the sender's
retransmission timeout. It definitely increases unnecessary latency.
Fixes: 5d9f4262b7ea ("tcp: add SACK compression")
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: fuyuanli <fuyuanli@didiglobal.com>
Signed-off-by: Jason Xing <kerneljasonxing@gmail.com>
Link: https://lore.kernel.org/netdev/20230529113804.GA20300@didi-ThinkCentre-M920t-N000/
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230531080150.GA20424@didi-ThinkCentre-M920t-N000
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If we send two TCA_FLOWER_KEY_ENC_OPTS_GENEVE packets and their total
size is 252 bytes(key->enc_opts.len = 252) then
key->enc_opts.len = opt->length = data_len / 4 = 0 when the third
TCA_FLOWER_KEY_ENC_OPTS_GENEVE packet enters fl_set_geneve_opt. This
bypasses the next bounds check and results in an out-of-bounds.
Fixes: 0a6e77784f49 ("net/sched: allow flower to match tunnel options")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com>
Link: https://lore.kernel.org/r/20230531102805.27090-1-hbh25y@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
If an IOMMU domain was never attached, it lacks any linkage to the
actual IOMMU hardware. Attempting to do flush_iotlb_all() on it will
result in a NULL pointer dereference. This seems to happen after the
recent IOMMU core rework in v6.4-rc1.
Unable to handle kernel read from unreadable memory at virtual address 0000000000000018
Call trace:
mtk_iommu_flush_iotlb_all+0x20/0x80
iommu_create_device_direct_mappings.part.0+0x13c/0x230
iommu_setup_default_domain+0x29c/0x4d0
iommu_probe_device+0x12c/0x190
of_iommu_configure+0x140/0x208
of_dma_configure_id+0x19c/0x3c0
platform_dma_configure+0x38/0x88
really_probe+0x78/0x2c0
Check if the "bank" field has been filled in before actually attempting
the IOTLB flush to avoid it. The IOTLB is also flushed when the device
comes out of runtime suspend, so it should have a clean initial state.
Fixes: 08500c43d4f7 ("iommu/mediatek: Adjust the structure")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230526085402.394239-1-wenst@chromium.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Clearing out report id and timestamp as means to detect unlanded reports
only works if report size is power of 2. That is, only when report size is
a sub-multiple of the OA buffer size can we be certain that reports will
land at the same place each time in the OA buffer (after rewind). If report
size is not a power of 2, we need to zero out the entire report to be able
to detect unlanded reports reliably.
v2: Add Fixes tag (Umesh)
Fixes: 1cc064dce4ed ("drm/i915/perf: Add support for OA media units")
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230523204042.4180641-1-ashutosh.dixit@intel.com
(cherry picked from commit 09a36015d9a0940214c080f95afc605c47648bbd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
There are 4 lanes in the single instance of J784S4 SERDES. Each SERDES
lane mux can select up to 4 different IPs. Define all the possible
functions.
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/755a14f1-92ad-ce4b-3fde-2a4b0650475c@axentia.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 0166dc11be91 ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
As a minor optimization, this also lets us drop of_match_ptr(), as we
now know what it will resolve to, we might as well save cpp some work.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/bc790b4e-1cb4-4ef5-3da8-9d0e6b613bc7@axentia.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Failure ladders weren't exactly unwinding what the function had done up
to that point; most seriously, when we encountered an already offloaded
rule, the failure path tried to remove the new rule from the hashtable,
which would in fact remove the already-present 'old' rule (since it has
the same key) from the table, and leak its resources.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202305200745.xmIlkqjH-lkp@intel.com/
Fixes: d902e1a737d4 ("sfc: bare bones TC offload on EF100")
Fixes: 17654d84b47c ("sfc: add offloading of 'foreign' TC (decap) rules")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230530202527.53115-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
During driver load it reads embedded_cpu bit from initialization
segment, but the initialization segment is readable only after
initialization bit is cleared.
Move the call to mlx5_read_embedded_cpu() right after initialization bit
cleared.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Fixes: 591905ba9679 ("net/mlx5: Introduce Mellanox SmartNIC and modify page management logic")
Reviewed-by: Shay Drory <shayd@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Allocation failure is outside the critical lock section and should
return immediately rather than jumping to the unlock section.
Also unlock as soon as required and remove the now redundant jump label.
Fixes: 80a2a9026b24 ("net/mlx5e: Add a lock on tir list")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
[ 9.837087] mlx5_core 0000:02:00.0: firmware version: 16.35.2000
[ 9.843126] mlx5_core 0000:02:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link)
[ 10.311515] mlx5_core 0000:02:00.0: Rate limit: 127 rates are supported, range: 0Mbps to 97656Mbps
[ 10.321948] mlx5_core 0000:02:00.0: E-Switch: Total vports 2, per vport: max uc(128) max mc(2048)
[ 10.344324] mlx5_core 0000:02:00.0: mlx5_pcie_event:301:(pid 88): PCIe slot advertised sufficient power (27W).
[ 10.354339] BUG: unable to handle page fault for address: ffffffff8ff0ade0
[ 10.361206] #PF: supervisor read access in kernel mode
[ 10.366335] #PF: error_code(0x0000) - not-present page
[ 10.371467] PGD 81ec39067 P4D 81ec39067 PUD 81ec3a063 PMD 114b07063 PTE 800ffff7e10f5062
[ 10.379544] Oops: 0000 [#1] PREEMPT SMP PTI
[ 10.383721] CPU: 0 PID: 117 Comm: kworker/0:6 Not tainted 6.3.0-13028-g7222f123c983 #1
[ 10.391625] Hardware name: Supermicro X10SRA-F/X10SRA-F, BIOS 2.0b 06/12/2017
[ 10.398750] Workqueue: events work_for_cpu_fn
[ 10.403108] RIP: 0010:__bitmap_or+0x10/0x26
[ 10.407286] Code: 85 c0 0f 95 c0 c3 cc cc cc cc 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 90 89 c9 31 c0 48 83 c1 3f 48 c1 e9 06 39 c>
[ 10.426024] RSP: 0000:ffffb45a0078f7b0 EFLAGS: 00010097
[ 10.431240] RAX: 0000000000000000 RBX: ffffffff8ff0adc0 RCX: 0000000000000004
[ 10.438365] RDX: ffff9156801967d0 RSI: ffffffff8ff0ade0 RDI: ffff9156801967b0
[ 10.445489] RBP: ffffb45a0078f7e8 R08: 0000000000000030 R09: 0000000000000000
[ 10.452613] R10: 0000000000000000 R11: 0000000000000000 R12: 00000000000000ec
[ 10.459737] R13: ffffffff8ff0ade0 R14: 0000000000000001 R15: 0000000000000020
[ 10.466862] FS: 0000000000000000(0000) GS:ffff9165bfc00000(0000) knlGS:0000000000000000
[ 10.474936] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 10.480674] CR2: ffffffff8ff0ade0 CR3: 00000001011ae003 CR4: 00000000003706f0
[ 10.487800] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 10.494922] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 10.502046] Call Trace:
[ 10.504493] <TASK>
[ 10.506589] ? matrix_alloc_area.constprop.0+0x43/0x9a
[ 10.511729] ? prepare_namespace+0x84/0x174
[ 10.515914] irq_matrix_reserve_managed+0x56/0x10c
[ 10.520699] x86_vector_alloc_irqs+0x1d2/0x31e
[ 10.525146] irq_domain_alloc_irqs_hierarchy+0x39/0x3f
[ 10.530284] irq_domain_alloc_irqs_parent+0x1a/0x2a
[ 10.535155] intel_irq_remapping_alloc+0x59/0x5e9
[ 10.539859] ? kmem_cache_debug_flags+0x11/0x26
[ 10.544383] ? __radix_tree_lookup+0x39/0xb9
[ 10.548649] irq_domain_alloc_irqs_hierarchy+0x39/0x3f
[ 10.553779] irq_domain_alloc_irqs_parent+0x1a/0x2a
[ 10.558650] msi_domain_alloc+0x8c/0x120
[ 10.567697] irq_domain_alloc_irqs_locked+0x11d/0x286
[ 10.572741] __irq_domain_alloc_irqs+0x72/0x93
[ 10.577179] __msi_domain_alloc_irqs+0x193/0x3f1
[ 10.581789] ? __xa_alloc+0xcf/0xe2
[ 10.585273] msi_domain_alloc_irq_at+0xa8/0xfe
[ 10.589711] pci_msix_alloc_irq_at+0x47/0x5c
The crash is due to matrix_alloc_area() attempting to access per-CPU
memory for CPUs that are not present on the system. The CPU mask
passed into reserve_managed_vector() via it's @irqd parameter is
corrupted because it contains uninitialized stack data.
Fixes: bbac70c74183 ("net/mlx5: Use newer affinity descriptor")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When dynamic IRQ allocation is not supported all IRQs are allocated up
front in mlx5_irq_table_create() instead of dynamically as part of
mlx5_irq_alloc(). In the latter dynamic case irq->map.index is set
via the mapping returned by pci_msix_alloc_irq_at(). In the static case
and prior to commit 1da438c0ae02 ("net/mlx5: Fix indexing of mlx5_irq")
irq->map.index was set in mlx5_irq_alloc() twice once initially to 0 and
then to the requested index before storing in the xarray. After this
commit it is only set to 0 which breaks all other IRQ mappings.
Fix this by setting irq->map.index to the requested index together with
irq->map.virq and improve the related comment to make it clearer which
cases it deals with.
Cc: Chuck Lever III <chuck.lever@oracle.com>
Tested-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Fixes: 1da438c0ae02 ("net/mlx5: Fix indexing of mlx5_irq")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
mlx5 add IRQs to rmap upon MSIX request, and mlx5 remove rmap from
MSIX only if msi_map.index is populated. However, msi_map.index is
populated only when dynamic MSIX is supported. This results in freeing
IRQs without removing them from rmap, which triggers the bellow
WARN_ON[1].
rmap is a feature which have no relation to dynamic MSIX.
Hence, remove the check of msi_map.index when removing IRQ from rmap.
[1]
[ 200.307160 ] WARNING: CPU: 20 PID: 1702 at kernel/irq/manage.c:2034 free_irq+0x2ac/0x358
[ 200.316990 ] CPU: 20 PID: 1702 Comm: modprobe Not tainted 6.4.0-rc3_for_upstream_min_debug_2023_05_24_14_02 #1
[ 200.318939 ] Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
[ 200.321659 ] pc : free_irq+0x2ac/0x358
[ 200.322400 ] lr : free_irq+0x20/0x358
[ 200.337865 ] Call trace:
[ 200.338360 ] free_irq+0x2ac/0x358
[ 200.339029 ] irq_release+0x58/0xd0 [mlx5_core]
[ 200.340093 ] mlx5_irqs_release_vectors+0x80/0xb0 [mlx5_core]
[ 200.341344 ] destroy_comp_eqs+0x120/0x170 [mlx5_core]
[ 200.342469 ] mlx5_eq_table_destroy+0x1c/0x38 [mlx5_core]
[ 200.343645 ] mlx5_unload+0x8c/0xc8 [mlx5_core]
[ 200.344652 ] mlx5_uninit_one+0x78/0x118 [mlx5_core]
[ 200.345745 ] remove_one+0x80/0x108 [mlx5_core]
[ 200.346752 ] pci_device_remove+0x40/0xd8
[ 200.347554 ] device_remove+0x50/0x88
[ 200.348272 ] device_release_driver_internal+0x1c4/0x228
[ 200.349312 ] driver_detach+0x54/0xa0
[ 200.350030 ] bus_remove_driver+0x74/0x100
[ 200.350833 ] driver_unregister+0x34/0x68
[ 200.351619 ] pci_unregister_driver+0x28/0xa0
[ 200.352476 ] mlx5_cleanup+0x14/0x2210 [mlx5_core]
[ 200.353536 ] __arm64_sys_delete_module+0x190/0x2e8
[ 200.354495 ] el0_svc_common.constprop.0+0x6c/0x1d0
[ 200.355455 ] do_el0_svc+0x38/0x98
[ 200.356122 ] el0_svc+0x1c/0x80
[ 200.356739 ] el0t_64_sync_handler+0xb4/0x130
[ 200.357604 ] el0t_64_sync+0x174/0x178
[ 200.358345 ] ---[ end trace 0000000000000000 ]---
Fixes: 3354822cde5a ("net/mlx5: Use dynamic msix vectors allocation")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add IP GC 11.0.1 in the list of target to have
tmz enabled by default.
Signed-off-by: Ikshwaku Chauhan <ikshwaku.chauhan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
|
|
Pull smb client fixes from Steve French:
"Four small smb3 client fixes:
- two small fixes suggested by kernel test robot
- small cleanup fix
- update Paulo's email address in the maintainer file"
* tag '6.4-rc4-smb3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: address unused variable warning
smb: delete an unnecessary statement
smb3: missing null check in SMB2_change_notify
smb3: update a reviewer email in MAINTAINERS file
|
|
During reboot test on arm64 platform, it may failure on boot.
The error message are as follows:
[ 1.706570][ 3] [ T273] [drm:si_thermal_enable_alert [amdgpu]] *ERROR* Could not enable thermal interrupts.
[ 1.716547][ 3] [ T273] [drm:amdgpu_device_ip_late_init [amdgpu]] *ERROR* late_init of IP block <si_dpm> failed -22
[ 1.727064][ 3] [ T273] amdgpu 0000:02:00.0: amdgpu_device_ip_late_init failed
[ 1.734367][ 3] [ T273] amdgpu 0000:02:00.0: Fatal error during GPU init
v2: squash in built warning fix (Alex)
Signed-off-by: Zhenneng Li <lizhenneng@kylinos.cn>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Add ras_poison_irq and functions. And fix the amdgpu_irq_put
call trace in jpeg_v4_0_hw_fini.
[ 50.497562] RIP: 0010:amdgpu_irq_put+0xa4/0xc0 [amdgpu]
[ 50.497619] RSP: 0018:ffffaa2400fcfcb0 EFLAGS: 00010246
[ 50.497620] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
[ 50.497621] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 50.497621] RBP: ffffaa2400fcfcd0 R08: 0000000000000000 R09: 0000000000000000
[ 50.497622] R10: 0000000000000000 R11: 0000000000000000 R12: ffff99b2105242d8
[ 50.497622] R13: 0000000000000000 R14: ffff99b210500000 R15: ffff99b210500000
[ 50.497623] FS: 0000000000000000(0000) GS:ffff99b518480000(0000) knlGS:0000000000000000
[ 50.497623] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 50.497624] CR2: 00007f9d32aa91e8 CR3: 00000001ba210000 CR4: 0000000000750ee0
[ 50.497624] PKRU: 55555554
[ 50.497625] Call Trace:
[ 50.497625] <TASK>
[ 50.497627] jpeg_v4_0_hw_fini+0x43/0xc0 [amdgpu]
[ 50.497693] jpeg_v4_0_suspend+0x13/0x30 [amdgpu]
[ 50.497751] amdgpu_device_ip_suspend_phase2+0x240/0x470 [amdgpu]
[ 50.497802] amdgpu_device_ip_suspend+0x41/0x80 [amdgpu]
[ 50.497854] amdgpu_device_pre_asic_reset+0xd9/0x4a0 [amdgpu]
[ 50.497905] amdgpu_device_gpu_recover.cold+0x548/0xcf1 [amdgpu]
[ 50.498005] amdgpu_debugfs_reset_work+0x4c/0x80 [amdgpu]
[ 50.498060] process_one_work+0x21f/0x400
[ 50.498063] worker_thread+0x200/0x3f0
[ 50.498064] ? process_one_work+0x400/0x400
[ 50.498065] kthread+0xee/0x120
[ 50.498067] ? kthread_complete_and_exit+0x20/0x20
[ 50.498068] ret_from_fork+0x22/0x30
Suggested-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add ras_poison_irq and functions.
Suggested-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Separate jpegbRAS poison consumption handling from the instance irq, and
register dedicated ras_poison_irq src and funcs for UVD_POISON.
v2:
- Separate ras irq from jpeg instance irq
- Improve the subject and code comments
v3:
- Split the patch into three parts
- Improve the code comments
Suggested-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add ras_poison_irq and functions. And fix the amdgpu_irq_put
call trace in vcn_v4_0_hw_fini.
[ 44.563572] RIP: 0010:amdgpu_irq_put+0xa4/0xc0 [amdgpu]
[ 44.563629] RSP: 0018:ffffb36740edfc90 EFLAGS: 00010246
[ 44.563630] RAX: 0000000000000000 RBX: 0000000000000001 RCX: 0000000000000000
[ 44.563630] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 44.563631] RBP: ffffb36740edfcb0 R08: 0000000000000000 R09: 0000000000000000
[ 44.563631] R10: 0000000000000000 R11: 0000000000000000 R12: ffff954c568e2ea8
[ 44.563631] R13: 0000000000000000 R14: ffff954c568c0000 R15: ffff954c568e2ea8
[ 44.563632] FS: 0000000000000000(0000) GS:ffff954f584c0000(0000) knlGS:0000000000000000
[ 44.563632] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 44.563633] CR2: 00007f028741ba70 CR3: 000000026ca10000 CR4: 0000000000750ee0
[ 44.563633] PKRU: 55555554
[ 44.563633] Call Trace:
[ 44.563634] <TASK>
[ 44.563634] vcn_v4_0_hw_fini+0x62/0x160 [amdgpu]
[ 44.563700] vcn_v4_0_suspend+0x13/0x30 [amdgpu]
[ 44.563755] amdgpu_device_ip_suspend_phase2+0x240/0x470 [amdgpu]
[ 44.563806] amdgpu_device_ip_suspend+0x41/0x80 [amdgpu]
[ 44.563858] amdgpu_device_pre_asic_reset+0xd9/0x4a0 [amdgpu]
[ 44.563909] amdgpu_device_gpu_recover.cold+0x548/0xcf1 [amdgpu]
[ 44.564006] amdgpu_debugfs_reset_work+0x4c/0x80 [amdgpu]
[ 44.564061] process_one_work+0x21f/0x400
[ 44.564062] worker_thread+0x200/0x3f0
[ 44.564063] ? process_one_work+0x400/0x400
[ 44.564064] kthread+0xee/0x120
[ 44.564065] ? kthread_complete_and_exit+0x20/0x20
[ 44.564066] ret_from_fork+0x22/0x30
Suggested-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add ras_poison_irq and functions.
Suggested-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Separate vcn RAS poison consumption handling from the instance irq, and
register dedicated ras_poison_irq src and funcs for UVD_POISON.
v2:
- Separate ras irq from vcn instance irq
- Improve the subject and code comments
v3:
- Split the patch into three parts
- Improve the code comments
Suggested-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Horatio Zhang <Hongkun.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 474f01015ffdb74e01c2eb3584a2822c64e7b2be.
Caused a regression:
Samsung Odyssey Neo G9, running at 5120x1440@240/VRR, connected to Navi
21 via DisplayPort, blanks and the GPU hangs while starting the Steam
game Assetto Corsa Competizione (via Proton 7.0).
Example dmesg excerpt:
amdgpu 0000:0c:00.0: [drm] ERROR [CRTC:82:crtc-0] flip_done timed out
NMI watchdog: Watchdog detected hard LOCKUP on cpu 6
[...]
RIP: 0010:amdgpu_device_rreg.part.0+0x2f/0xf0 [amdgpu]
Code: 41 54 44 8d 24 b5 00 00 00 00 55 89 f5 53 48 89 fb 4c 3b a7 60 0b 00 00 73 6a 83 e2 02 74 29 4c 03 a3 68 0b 00 00 45 8b 24 24 <48> 8b 43 08 0f b7 70 3e 66 90 44 89 e0 5b 5d 41 5c 31 d2 31 c9 31
RSP: 0000:ffffb39a119dfb88 EFLAGS: 00000086
RAX: ffffffffc0eb96a0 RBX: ffff9e7963dc0000 RCX: 0000000000007fff
RDX: 0000000000000000 RSI: 0000000000004ff6 RDI: ffff9e7963dc0000
RBP: 0000000000004ff6 R08: ffffb39a119dfc40 R09: 0000000000000010
R10: ffffb39a119dfc40 R11: ffffb39a119dfc44 R12: 00000000000e05ae
R13: 0000000000000000 R14: ffff9e7963dc0010 R15: 0000000000000000
FS: 000000001012f6c0(0000) GS:ffff9e805eb80000(0000) knlGS:000000007fd40000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000461ca000 CR3: 00000002a8a20000 CR4: 0000000000350ee0
Call Trace:
<TASK>
dm_read_reg_func+0x37/0xc0 [amdgpu]
generic_reg_get2+0x22/0x60 [amdgpu]
optc1_get_crtc_scanoutpos+0x6a/0xc0 [amdgpu]
dc_stream_get_scanoutpos+0x74/0x90 [amdgpu]
dm_crtc_get_scanoutpos+0x82/0xf0 [amdgpu]
amdgpu_display_get_crtc_scanoutpos+0x91/0x190 [amdgpu]
? dm_read_reg_func+0x37/0xc0 [amdgpu]
amdgpu_get_vblank_counter_kms+0xb4/0x1a0 [amdgpu]
dm_pflip_high_irq+0x213/0x2f0 [amdgpu]
amdgpu_dm_irq_handler+0x8a/0x200 [amdgpu]
amdgpu_irq_dispatch+0xd4/0x220 [amdgpu]
amdgpu_ih_process+0x7f/0x110 [amdgpu]
amdgpu_irq_handler+0x1f/0x70 [amdgpu]
__handle_irq_event_percpu+0x46/0x1b0
handle_irq_event+0x34/0x80
handle_edge_irq+0x9f/0x240
__common_interrupt+0x66/0x110
common_interrupt+0x5c/0xd0
asm_common_interrupt+0x22/0x40
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit ce560ac40272a5c8b5b68a9d63a75edd9e66aed2.
It depends on its parent commit, which we want to revert.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Michel Dänzer <mdaenzer@redhat.com>
[Hamza: fix a whitespace issue in dcn30_prepare_bandwidth()]
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk for renoir.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels are
given the reversed orders by PMFW. Like the memory DPM clocks
that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This patch reverses the DPM clocks levels output of pp_dpm_mclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This patch reverses the DPM clocks levels output of pp_dpm_mclk
and pp_dpm_fclk.
On dGPUs and older APUs we expose the levels from lowest clocks
to highest clocks. But for some APUs, the clocks levels that from
the DFPstateTable are given the reversed orders by PMFW. Like the
memory DPM clocks that are exposed by pp_dpm_mclk.
It's not intuitive that they are reversed on these APUs. All tools
and software that talks to the driver then has to know different ways
to interpret the data depending on the asic.
So we need to reverse them to expose the clocks levels from the
driver consistently.
Signed-off-by: Tim Huang <Tim.Huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Until commit 5c2712387d48 ("cacheinfo: Fix LLC is not exported through
sysfs"), cacheinfo called populate_cache_leaves() for CPU coming online
which let the arch specific functions handle (at least on x86)
populating the shared_cpu_map. However, with the changes in the
aforementioned commit, populate_cache_leaves() is not called when a CPU
comes online as a result of hotplug since last_level_cache_is_valid()
returns true as the cacheinfo data is not discarded. The CPU coming
online is not present in shared_cpu_map, however, it will not be added
since the cpu_cacheinfo->cpu_map_populated flag is set (it is set in
populate_cache_leaves() when cacheinfo is first populated for x86)
This can lead to inconsistencies in the shared_cpu_map when an offlined
CPU comes online again. Example below depicts the inconsistency in the
shared_cpu_list in cacheinfo when CPU8 is offlined and onlined again on
a 3rd Generation EPYC processor:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# echo 1 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8
# cat /sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list
136
# cat /sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list
9-15,136-143
Clear the flag when the CPU is removed from shared_cpu_map when
cache_shared_cpu_map_remove() is called during CPU hotplug. This will
allow cache_shared_cpu_map_setup() to add the CPU coming back online in
the shared_cpu_map. Set the flag again when the shared_cpu_map is setup.
Following are results of performing the same test as described above with
the changes:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# echo 1 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# cat /sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list
8,136
# cat /sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list
8-15,136-143
Fixes: 5c2712387d48 ("cacheinfo: Fix LLC is not exported through sysfs")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Reviewed-by: Yicong Yang <yangyicong@hisilicon.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230508084115.1157-3-kprateek.nayak@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While building the shared_cpu_map, check if the cache level and cache
type matches. On certain systems that build the cache topology based on
the instance ID, there are cases where the same ID may repeat across
multiple cache levels, leading inaccurate topology.
In event of CPU offlining, the cache_shared_cpu_map_remove() does not
consider if IDs at same level are being compared. As a result, when same
IDs repeat across different cache levels, the CPU going offline is not
removed from all the shared_cpu_map.
Below is the output of cache topology of CPU8 and it's SMT sibling after
CPU8 is offlined on a dual socket 3rd Generation AMD EPYC processor
(2 x 64C/128T) running kernel release v6.3:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu136/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu136/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list: 9-15,136-143
CPU8 is removed from index0 (L1i) but remains in the shared_cpu_list of
index1 (L1d) and index2 (L2). Since L1i, L1d, and L2 are shared by the
SMT siblings, and they have the same cache instance ID, CPU 2 is only
removed from the first index with matching ID which is index1 (L1i) in
this case. With this fix, the results are as expected when performing
the same experiment on the same system:
# for i in /sys/devices/system/cpu/cpu8/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu8/cache/index0/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index1/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index2/shared_cpu_list: 8,136
/sys/devices/system/cpu/cpu8/cache/index3/shared_cpu_list: 8-15,136-143
# echo 0 > /sys/devices/system/cpu/cpu8/online
# for i in /sys/devices/system/cpu/cpu136/cache/index*/shared_cpu_list; do echo -n "$i: "; cat $i; done
/sys/devices/system/cpu/cpu136/cache/index0/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index1/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index2/shared_cpu_list: 136
/sys/devices/system/cpu/cpu136/cache/index3/shared_cpu_list: 9-15,136-143
When rebuilding topology, the same problem appears as
cache_shared_cpu_map_setup() implements a similar logic. Consider the
same 3rd Generation EPYC processor: CPUs in Core 1, that share the L1
and L2 caches, have L1 and L2 instance ID as 1. For all the CPUs on
the second chiplet, the L3 ID is also 1 leading to grouping on CPUs from
Core 1 (1, 17) and the entire second chiplet (8-15, 24-31) as CPUs
sharing one cache domain. This went undetected since x86 processors
depended on arch specific populate_cache_leaves() method to repopulate
the shared_cpus_map when CPU came back online until kernel release
v6.3-rc5.
Fixes: 198102c9103f ("cacheinfo: Fix shared_cpu_map to handle shared caches at different levels")
Signed-off-by: K Prateek Nayak <kprateek.nayak@amd.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Link: https://lore.kernel.org/r/20230508084115.1157-2-kprateek.nayak@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current code will, if we do not specify unique labels
for the SRAM subnodes, fail to register several nodes named
the same.
Example:
sram@40020000 {
(...)
sram@0 {
(...)
};
sram@1000 {
(...)
};
};
Since the child->name in both cases will be "sram" the
gen_pool_create() will fail because the name is not unique.
Use dev_name() for the device as this will have bus ID
set to the fully translated address for the node, and that
will always be unique.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230417-ux500-sram-v2-2-6e62ad551faa@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds an SoC-specific binding for the banks of eSRAM
available in the ST-Ericsson U8500.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230417-ux500-sram-v2-1-6e62ad551faa@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The following kernel memory leak was noticed after running
tools/testing/selftests/firmware/fw_run_tests.sh:
[root@pc-mtodorov firmware]# cat /sys/kernel/debug/kmemleak
.
.
.
unreferenced object 0xffff955389bc3400 (size 1024):
comm "test_firmware-0", pid 5451, jiffies 4294944822 (age 65.652s)
hex dump (first 32 bytes):
47 48 34 35 36 37 0a 00 00 00 00 00 00 00 00 00 GH4567..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff962f5dec>] slab_post_alloc_hook+0x8c/0x3c0
[<ffffffff962fcca4>] __kmem_cache_alloc_node+0x184/0x240
[<ffffffff962704de>] kmalloc_trace+0x2e/0xc0
[<ffffffff9665b42d>] test_fw_run_batch_request+0x9d/0x180
[<ffffffff95fd813b>] kthread+0x10b/0x140
[<ffffffff95e033e9>] ret_from_fork+0x29/0x50
unreferenced object 0xffff9553c334b400 (size 1024):
comm "test_firmware-1", pid 5452, jiffies 4294944822 (age 65.652s)
hex dump (first 32 bytes):
47 48 34 35 36 37 0a 00 00 00 00 00 00 00 00 00 GH4567..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff962f5dec>] slab_post_alloc_hook+0x8c/0x3c0
[<ffffffff962fcca4>] __kmem_cache_alloc_node+0x184/0x240
[<ffffffff962704de>] kmalloc_trace+0x2e/0xc0
[<ffffffff9665b42d>] test_fw_run_batch_request+0x9d/0x180
[<ffffffff95fd813b>] kthread+0x10b/0x140
[<ffffffff95e033e9>] ret_from_fork+0x29/0x50
unreferenced object 0xffff9553c334f000 (size 1024):
comm "test_firmware-2", pid 5453, jiffies 4294944822 (age 65.652s)
hex dump (first 32 bytes):
47 48 34 35 36 37 0a 00 00 00 00 00 00 00 00 00 GH4567..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff962f5dec>] slab_post_alloc_hook+0x8c/0x3c0
[<ffffffff962fcca4>] __kmem_cache_alloc_node+0x184/0x240
[<ffffffff962704de>] kmalloc_trace+0x2e/0xc0
[<ffffffff9665b42d>] test_fw_run_batch_request+0x9d/0x180
[<ffffffff95fd813b>] kthread+0x10b/0x140
[<ffffffff95e033e9>] ret_from_fork+0x29/0x50
unreferenced object 0xffff9553c3348400 (size 1024):
comm "test_firmware-3", pid 5454, jiffies 4294944822 (age 65.652s)
hex dump (first 32 bytes):
47 48 34 35 36 37 0a 00 00 00 00 00 00 00 00 00 GH4567..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff962f5dec>] slab_post_alloc_hook+0x8c/0x3c0
[<ffffffff962fcca4>] __kmem_cache_alloc_node+0x184/0x240
[<ffffffff962704de>] kmalloc_trace+0x2e/0xc0
[<ffffffff9665b42d>] test_fw_run_batch_request+0x9d/0x180
[<ffffffff95fd813b>] kthread+0x10b/0x140
[<ffffffff95e033e9>] ret_from_fork+0x29/0x50
[root@pc-mtodorov firmware]#
Note that the size 1024 corresponds to the size of the test firmware
buffer. The actual number of the buffers leaked is around 70-110,
depending on the test run.
The cause of the leak is the following:
request_partial_firmware_into_buf() and request_firmware_into_buf()
provided firmware buffer isn't released on release_firmware(), we
have allocated it and we are responsible for deallocating it manually.
This is introduced in a number of context where previously only
release_firmware() was called, which was insufficient.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Fixes: 7feebfa487b92 ("test_firmware: add support for request_firmware_into_buf")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Tianfei zhang <tianfei.zhang@intel.com>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Zhengchao Shao <shaozhengchao@huawei.com>
Cc: Colin Ian King <colin.i.king@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: Kees Cook <keescook@chromium.org>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org # v5.4
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/r/20230509084746.48259-3-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dan Carpenter spotted that test_fw_config->reqs will be leaked if
trigger_batched_requests_store() is called two or more times.
The same appears with trigger_batched_requests_async_store().
This bug wasn't trigger by the tests, but observed by Dan's visual
inspection of the code.
The recommended workaround was to return -EBUSY if test_fw_config->reqs
is already allocated.
Fixes: 7feebfa487b92 ("test_firmware: add support for request_firmware_into_buf")
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Tianfei Zhang <tianfei.zhang@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Colin Ian King <colin.i.king@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org # v5.4
Suggested-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230509084746.48259-2-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dan Carpenter spotted a race condition in a couple of situations like
these in the test_firmware driver:
static int test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
{
u8 val;
int ret;
ret = kstrtou8(buf, 10, &val);
if (ret)
return ret;
mutex_lock(&test_fw_mutex);
*(u8 *)cfg = val;
mutex_unlock(&test_fw_mutex);
/* Always return full write size even if we didn't consume all */
return size;
}
static ssize_t config_num_requests_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
int rc;
mutex_lock(&test_fw_mutex);
if (test_fw_config->reqs) {
pr_err("Must call release_all_firmware prior to changing config\n");
rc = -EINVAL;
mutex_unlock(&test_fw_mutex);
goto out;
}
mutex_unlock(&test_fw_mutex);
rc = test_dev_config_update_u8(buf, count,
&test_fw_config->num_requests);
out:
return rc;
}
static ssize_t config_read_fw_idx_store(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
return test_dev_config_update_u8(buf, count,
&test_fw_config->read_fw_idx);
}
The function test_dev_config_update_u8() is called from both the locked
and the unlocked context, function config_num_requests_store() and
config_read_fw_idx_store() which can both be called asynchronously as
they are driver's methods, while test_dev_config_update_u8() and siblings
change their argument pointed to by u8 *cfg or similar pointer.
To avoid deadlock on test_fw_mutex, the lock is dropped before calling
test_dev_config_update_u8() and re-acquired within test_dev_config_update_u8()
itself, but alas this creates a race condition.
Having two locks wouldn't assure a race-proof mutual exclusion.
This situation is best avoided by the introduction of a new, unlocked
function __test_dev_config_update_u8() which can be called from the locked
context and reducing test_dev_config_update_u8() to:
static int test_dev_config_update_u8(const char *buf, size_t size, u8 *cfg)
{
int ret;
mutex_lock(&test_fw_mutex);
ret = __test_dev_config_update_u8(buf, size, cfg);
mutex_unlock(&test_fw_mutex);
return ret;
}
doing the locking and calling the unlocked primitive, which enables both
locked and unlocked versions without duplication of code.
The similar approach was applied to all functions called from the locked
and the unlocked context, which safely mitigates both deadlocks and race
conditions in the driver.
__test_dev_config_update_bool(), __test_dev_config_update_u8() and
__test_dev_config_update_size_t() unlocked versions of the functions
were introduced to be called from the locked contexts as a workaround
without releasing the main driver's lock and thereof causing a race
condition.
The test_dev_config_update_bool(), test_dev_config_update_u8() and
test_dev_config_update_size_t() locked versions of the functions
are being called from driver methods without the unnecessary multiplying
of the locking and unlocking code for each method, and complicating
the code with saving of the return value across lock.
Fixes: 7feebfa487b92 ("test_firmware: add support for request_firmware_into_buf")
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russ Weight <russell.h.weight@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tianfei Zhang <tianfei.zhang@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Colin Ian King <colin.i.king@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-kselftest@vger.kernel.org
Cc: stable@vger.kernel.org # v5.4
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr>
Link: https://lore.kernel.org/r/20230509084746.48259-1-mirsad.todorovac@alu.unizg.hr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The crypto_alloc_shash() function doesn't return NULL, it returns
error pointers. Update the check accordingly.
Fixes: 02fe26f25325 ("firmware_loader: Add debug message with checksum for FW file")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/36ef6042-ce74-4e8e-9e2c-5b5c28940610@kili.mountain
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
@xilinx.com is still working but better to switch to new amd.com after
AMD/Xilinx acquisition.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/36d119221aa12369c601cd37160306aeb84fc973.1684244767.git.michal.simek@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Function ll_rw_block was removed in commit 79f597842069 ("fs/buffer:
remove ll_rw_block() helper"). There is no unified function to sumbit
read or write buffer in block layer for now. Consider similar sematics,
we can choose submit_bh() to replace ll_rw_block() as predefined crash
point. In submit_bh(), it also takes read or write flag as the first
argument and invoke submit_bio() to submit I/O request to block layer.
Fixes: 79f597842069 ("fs/buffer: remove ll_rw_block() helper")
Signed-off-by: Yue Zhao <findns94@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230503162944.3969-1-findns94@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There was a bug where this code forgot to unlock the tdev->mutex if the
kzalloc() failed. Fix this issue, by moving the allocation outside the
lock.
Fixes: 2d1e952a2b8e ("mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. SPEAKUP_SERIALIO thus needs to depend on HAS_IOPORT.
Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-34-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. Add dependencies for those drivers that use them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-27-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. As PC style parport uses these functions we need to
handle this dependency.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-24-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them. With that the !S390 dependency on ISDN can be
removed as all drivers without HAS_IOPORT requirement now build.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-21-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to guard sections of code calling them
as alternative access methods.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-11-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 104_QUAD_8 counter driver uses devm_ioport_map() without depending
on HAS_IOPORT_MAP. This means the driver is not usable on platforms such
as s390 which do not support I/O port mapping. Add the missing
HAS_IOPORT_MAP dependency to make this explicit.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-8-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-7-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230522105049.1467313-4-schnelle@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull rdma fixes from Jason Gunthorpe:
- Fix 64K ARM page size support in bnxt_re and efa
- bnxt_re fixes for a memory leak, incorrect error handling and a
remove a bogus FW failure when running on a VF
- Update MAINTAINERS for hns and efa
- Fix two rxe regressions added this merge window in error unwind and
incorrect spinlock primitives
- hns gets a better algorithm for allocating page tables to avoid
running out of resources, and a timeout adjustment
- Fix a text case failure in hns
- Use after free in irdma and fix incorrect construction of a WQE
causing mis-execution
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/irdma: Fix Local Invalidate fencing
RDMA/irdma: Prevent QP use after free
MAINTAINERS: Update maintainer of Amazon EFA driver
RDMA/bnxt_re: Do not enable congestion control on VFs
RDMA/bnxt_re: Fix return value of bnxt_re_process_raw_qp_pkt_rx
RDMA/bnxt_re: Fix a possible memory leak
RDMA/hns: Modify the value of long message loopback slice
RDMA/hns: Fix base address table allocation
RDMA/hns: Fix timeout attr in query qp for HIP08
RDMA/efa: Fix unsupported page sizes in device
RDMA/rxe: Convert spin_{lock_bh,unlock_bh} to spin_{lock_irqsave,unlock_irqrestore}
RDMA/rxe: Fix double unlock in rxe_qp.c
MAINTAINERS: Update maintainers of HiSilicon RoCE
RDMA/bnxt_re: Fix the page_size used during the MR creation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix two regressions in ext4 and a number of issues reported by syzbot"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: enable the lazy init thread when remounting read/write
ext4: fix fsync for non-directories
ext4: add lockdep annotations for i_data_sem for ea_inode's
ext4: disallow ea_inodes with extended attributes
ext4: set lockdep subclass for the ea_inode in ext4_xattr_inode_cache_find()
ext4: add EA_INODE checking to ext4_iget()
|
|
to_amba_device() now properly keeps the const-ness of the dev pointer
passed into it, while as before it could be lost.
Signed-off-by: Prathu Baronia <prathubaronia2011@gmail.com>
Link: https://lore.kernel.org/r/20230518134656.9559-1-prathubaronia2011@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a Device Feature List (DFL) feature id as a generic mechanism
to expose a vendor-specific FPGA IP to user space. The feature id
is intended for use with IPs that do not need any kernel services
beyond exposure to user space through the UIO DFL driver.
The feature id is used in, e.g., Intel Oak Springs Canyon IPUs
to expose various IPs to user space, e.g., Network Controller
Sideband Interface (NC-SI), BaseNIC, and VirtIO management.
Link: https://github.com/OPAE/dfl-feature-id
Signed-off-by: Peter Colberg <peter.colberg@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Reviewed-by: Russ Weight <russell.h.weight@intel.com>
Link: https://lore.kernel.org/r/20230531030737.12989-1-peter.colberg@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
vma_close frees qfrs but not clears q->qfrs, which still points
to the freed object, leading to subsequent mmap fail.
So vma_close clears q->qfrs as well.
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://lore.kernel.org/r/20230511095921.9331-3-zhangfei.gao@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The inode can be different in a container, for example, a docker and host
both open the same uacce parent device, which uses the same uacce struct
but different inode, so uacce->inode is not enough.
What's worse, when docker stops, the inode will be destroyed as well,
causing use-after-free in uacce_remove.
So use q->mapping to replace uacce->inode->i_mapping.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Link: https://lore.kernel.org/r/20230511095921.9331-2-zhangfei.gao@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver does not use i2c, so there is no point in including
<linux/i2c.h>
Remove it.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/002f7afb1a2935bc2357c4b1450b757f40902a8c.1682319647.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The functions are redundant as they are empty and performed by the misc
driver.
Signed-off-by: Bo Svangård <bo.svangard@sylog.se>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230422195933.523874-1-bo.svangard@sylog.se
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull an irqchip fix from Marc Zyngier:
- Fix regression introduced by the Mediatek workaround.
Link: https://lore.kernel.org/lkml/20230531160549.433528-1-maz@kernel.org
|
|
No Management involved in Zone Appened.
Fixes: bd83fe6f2cd2 ("nvme: add verbose error logging")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an attempt at contacting a receiver or a device fails because the
receiver or device never responds, don't restart the communication, only
restart it if the receiver or device answers that it's busy, as originally
intended.
This was the behaviour on communication timeout before commit 586e8fede795
("HID: logitech-hidpp: Retry commands when device is busy").
This fixes some overly long waits in a critical path on boot, when
checking whether the device is connected by getting its HID++ version.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Suggested-by: Mark Lord <mlord@pobox.com>
Fixes: 586e8fede795 ("HID: logitech-hidpp: Retry commands when device is busy")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Early alternatives are called with the mmu disabled, and then should not
access any global symbols through the GOT since it requires relocations,
relocations that we do before but *virtually*. So only use medany code
model for this early code.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com> # booted on nezha & unmatched
Fixes: 39b33072941f ("riscv: Introduce CONFIG_RELOCATABLE")
Link: https://lore.kernel.org/r/20230526154630.289374-1-alexghiti@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The bug here is that you cannot rely on getting the same socket
from multiple calls to fget() because userspace can influence
that. This is a kind of double fetch bug.
The fix is to delete the svc_alien_sock() function and instead do
the checking inside the svc_addsock() function.
Fixes: 3064639423c4 ("nfsd: check passed socket's net matches NFSd superblock's one")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: NeilBrown <neilb@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
All callers of trace_probe_primary_from_call() check the return
value to be non NULL. However, the function returns
list_first_entry(&tpe->probes, ...) which can never be NULL.
Additionally, it does not check for the list being possibly empty,
possibly causing a type confusion on empty lists.
Use list_first_entry_or_null() which solves both problems.
Link: https://lore.kernel.org/linux-trace-kernel/20230128-list-entry-null-check-v1-1-8bde6a3da2ef@diag.uniroma1.it/
Fixes: 60d53e2c3b75 ("tracing/probe: Split trace_event related data from trace_probe")
Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it>
Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Acked-by: Mukesh Ojha <quic_mojha@quicinc.com>
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Syzkaller got the following report:
BUG: KASAN: use-after-free in sk_setup_caps+0x621/0x690 net/core/sock.c:2018
Read of size 8 at addr ffff888027f82780 by task syz-executor276/3255
The function sk_setup_caps (called by ip6_sk_dst_store_flow->
ip6_dst_store) referenced already freed memory as this memory was
freed by parallel task in udpv6_sendmsg->ip6_sk_dst_lookup_flow->
sk_dst_check.
task1 (connect) task2 (udp6_sendmsg)
sk_setup_caps->sk_dst_set |
| sk_dst_check->
| sk_dst_set
| dst_release
sk_setup_caps references |
to already freed dst_entry|
The reason for this race condition is: sk_setup_caps() keeps using
the dst after transferring the ownership to the dst cache.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KVM maintains a mask of supported CPUs when a vPMU type is explicitly
selected by userspace and is used to reject any attempt to run the vCPU
on an unsupported CPU. This is great, but we're still beholden to the
default behavior where vCPUs can be scheduled anywhere and guest
counters may silently stop working.
Avoid confusing the next poor sod to look at this code and document the
intended behavior.
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230525212723.3361524-3-oliver.upton@linux.dev
|
|
To date KVM has relied on using a perf event to probe the core PMU at
the time of vPMU initialization. Behind the scenes perf_event_init()
would iteratively walk the PMUs of the system and return the PMU that
could handle the event. However, an upcoming change in perf core will
drop the iterative walk, thereby breaking the fragile dance we do on the
KVM side.
Avoid the problem altogether by iterating over the list of supported
PMUs maintained in KVM, returning the core PMU that matches the CPU
we were called on.
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230525212723.3361524-2-oliver.upton@linux.dev
|
|
The current code for the length calculation wrongly truncates the reported
length of the groups array, causing an under report of the subscribed
groups. To fix this, use 'BITS_TO_BYTES()' which rounds up the
division by 8.
Fixes: b42be38b2778 ("netlink: add API to retrieve all group memberships")
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230529153335.389815-1-pctammela@mojatatu.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The reference count on page table allocations is increased for every
'counted' PTE (valid or donated) in the table in addition to the initial
reference from ->zalloc_page(). kvm_pgtable_stage2_free_removed() fails
to drop the last reference on the root of the table walk, meaning we
leak memory.
Fix it by dropping the last reference after the free walker returns,
at which point all references for 'counted' PTEs have been released.
Cc: stable@vger.kernel.org
Fixes: 5c359cca1faf ("KVM: arm64: Tear down unlinked stage-2 subtree after break-before-make")
Reported-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Tested-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230530193213.1663411-1-oliver.upton@linux.dev
|
|
When use the following command to test:
1)ip link add bond0 type bond
2)ip link set bond0 up
3)tc qdisc add dev bond0 root handle ffff: mq
4)tc qdisc replace dev bond0 parent ffff:fff1 handle ffff: mq
The kernel reports NULL pointer dereference issue. The stack information
is as follows:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Internal error: Oops: 0000000096000006 [#1] SMP
Modules linked in:
pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mq_attach+0x44/0xa0
lr : qdisc_graft+0x20c/0x5cc
sp : ffff80000e2236a0
x29: ffff80000e2236a0 x28: ffff0000c0e59d80 x27: ffff0000c0be19c0
x26: ffff0000cae3e800 x25: 0000000000000010 x24: 00000000fffffff1
x23: 0000000000000000 x22: ffff0000cae3e800 x21: ffff0000c9df4000
x20: ffff0000c9df4000 x19: 0000000000000000 x18: ffff80000a934000
x17: ffff8000f5b56000 x16: ffff80000bb08000 x15: 0000000000000000
x14: 0000000000000000 x13: 6b6b6b6b6b6b6b6b x12: 6b6b6b6b00000001
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffff0000c0be0730 x7 : bbbbbbbbbbbbbbbb x6 : 0000000000000008
x5 : ffff0000cae3e864 x4 : 0000000000000000 x3 : 0000000000000001
x2 : 0000000000000001 x1 : ffff8000090bc23c x0 : 0000000000000000
Call trace:
mq_attach+0x44/0xa0
qdisc_graft+0x20c/0x5cc
tc_modify_qdisc+0x1c4/0x664
rtnetlink_rcv_msg+0x354/0x440
netlink_rcv_skb+0x64/0x144
rtnetlink_rcv+0x28/0x34
netlink_unicast+0x1e8/0x2a4
netlink_sendmsg+0x308/0x4a0
sock_sendmsg+0x64/0xac
____sys_sendmsg+0x29c/0x358
___sys_sendmsg+0x90/0xd0
__sys_sendmsg+0x7c/0xd0
__arm64_sys_sendmsg+0x2c/0x38
invoke_syscall+0x54/0x114
el0_svc_common.constprop.1+0x90/0x174
do_el0_svc+0x3c/0xb0
el0_svc+0x24/0xec
el0t_64_sync_handler+0x90/0xb4
el0t_64_sync+0x174/0x178
This is because when mq is added for the first time, qdiscs in mq is set
to NULL in mq_attach(). Therefore, when replacing mq after adding mq, we
need to initialize qdiscs in the mq before continuing to graft. Otherwise,
it will couse NULL pointer dereference issue in mq_attach(). And the same
issue will occur in the attach functions of mqprio, taprio and htb.
ffff:fff1 means that the repalce qdisc is ingress. Ingress does not allow
any qdisc to be attached. Therefore, ffff:fff1 is incorrectly used, and
the command should be dropped.
Fixes: 6ec1c69a8f64 ("net_sched: add classful multiqueue dummy scheduler")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Tested-by: Peilin Ye <peilin.ye@bytedance.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20230527093747.3583502-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Peilin Ye says:
====================
net/sched: Fixes for sch_ingress and sch_clsact
These are v6 fixes for ingress and clsact Qdiscs, including only first 4
patches (already tested and reviewed) from v5. Patch 5 and 6 from
previous versions are still under discussion and will be sent separately.
[a] https://syzkaller.appspot.com/bug?extid=b53a9c0d1ea4ad62da8b
Link to v5: https://lore.kernel.org/r/cover.1684887977.git.peilin.ye@bytedance.com/
Link to v4: https://lore.kernel.org/r/cover.1684825171.git.peilin.ye@bytedance.com/
Link to v3 (incomplete): https://lore.kernel.org/r/cover.1684821877.git.peilin.ye@bytedance.com/
Link to v2: https://lore.kernel.org/r/cover.1684796705.git.peilin.ye@bytedance.com/
Link to v1: https://lore.kernel.org/r/cover.1683326865.git.peilin.ye@bytedance.com/
====================
Link: https://lore.kernel.org/r/cover.1685388545.git.peilin.ye@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently, after creating an ingress (or clsact) Qdisc and grafting it
under TC_H_INGRESS (TC_H_CLSACT), it is possible to graft it again under
e.g. a TBF Qdisc:
$ ip link add ifb0 type ifb
$ tc qdisc add dev ifb0 handle 1: root tbf rate 20kbit buffer 1600 limit 3000
$ tc qdisc add dev ifb0 clsact
$ tc qdisc link dev ifb0 handle ffff: parent 1:1
$ tc qdisc show dev ifb0
qdisc tbf 1: root refcnt 2 rate 20Kbit burst 1600b lat 560.0ms
qdisc clsact ffff: parent ffff:fff1 refcnt 2
^^^^^^^^
clsact's refcount has increased: it is now grafted under both
TC_H_CLSACT and 1:1.
ingress and clsact Qdiscs should only be used under TC_H_INGRESS
(TC_H_CLSACT). Prohibit regrafting them.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Fixes: 1f211a1b929c ("net, sched: add clsact qdisc")
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Currently it is possible to add e.g. an HTB Qdisc under ffff:fff1
(TC_H_INGRESS, TC_H_CLSACT):
$ ip link add name ifb0 type ifb
$ tc qdisc add dev ifb0 parent ffff:fff1 htb
$ tc qdisc add dev ifb0 clsact
Error: Exclusivity flag on, cannot modify.
$ drgn
...
>>> ifb0 = netdev_get_by_name(prog, "ifb0")
>>> qdisc = ifb0.ingress_queue.qdisc_sleeping
>>> print(qdisc.ops.id.string_().decode())
htb
>>> qdisc.flags.value_() # TCQ_F_INGRESS
2
Only allow ingress and clsact Qdiscs under ffff:fff1. Return -EINVAL
for everything else. Make TCQ_F_INGRESS a static flag of ingress and
clsact Qdiscs.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Fixes: 1f211a1b929c ("net, sched: add clsact qdisc")
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
clsact Qdiscs are only supposed to be created under TC_H_CLSACT (which
equals TC_H_INGRESS). Return -EOPNOTSUPP if 'parent' is not
TC_H_CLSACT.
Fixes: 1f211a1b929c ("net, sched: add clsact qdisc")
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ingress Qdiscs are only supposed to be created under TC_H_INGRESS.
Return -EOPNOTSUPP if 'parent' is not TC_H_INGRESS, similar to
mq_init().
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot+b53a9c0d1ea4ad62da8b@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/r/0000000000006cf87705f79acf1a@google.com/
Tested-by: Pedro Tammela <pctammela@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Upon keep alive completion, nvme_keep_alive_work is scheduled with the
same delay every time. If keep alive commands are completing slowly,
this may cause a keep alive timeout. The following trace illustrates the
issue, taking KATO = 8 and TBKAS off for simplicity:
1. t = 0: run nvme_keep_alive_work, send keep alive
2. t = ε: keep alive reaches controller, controller restarts its keep
alive timer
3. t = 4: host receives keep alive completion, schedules
nvme_keep_alive_work with delay 4
4. t = 8: run nvme_keep_alive_work, send keep alive
Here, a keep alive having RTT of 4 causes a delay of at least 8 - ε
between the controller receiving successive keep alives. With ε small,
the controller is likely to detect a keep alive timeout.
Fix this by calculating the RTT of the keep alive command, and adjusting
the scheduling delay of the next keep alive work accordingly.
Reported-by: Costa Sapuntzakis <costa@purestorage.com>
Reported-by: Randy Jennings <randyj@purestorage.com>
Signed-off-by: Uday Shankar <ushankar@purestorage.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"One bug fix and two build warning fixes:
- call proper end bio callback for metadata RAID0 in a rare case of
an unaligned block
- fix uninitialized variable (reported by gcc 10.2)
- fix warning about potential access beyond array bounds on mips64
with 64k pages (runtime check would not allow that)"
* tag 'for-6.4-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix csum_tree_block page iteration to avoid tripping on -Werror=array-bounds
btrfs: fix an uninitialized variable warning in btrfs_log_inode
btrfs: call btrfs_orig_bbio_end_io in btrfs_end_bio_work
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix BPF CO-RE naming convention for checking the availability of
fields on 'union perf_mem_data_src' on the running kernel
- Remove the use of llvm-strip on BPF skel object files, not needed,
fixes a build breakage when the llvm package, that contains it in
most distros, isn't installed
- Fix tools that use both evsel->{bpf_counter_list,bpf_filters},
removing them from a union
- Remove extra "--" from the 'perf ftrace latency' --use-nsec option,
previously it was working only when using the '-n' alternative
- Don't stop building when both binutils-devel and a C++ compiler isn't
available to compile the alternative C++ demangle support code,
disable that feature instead
- Sync the linux/in.h and coresight-pmu.h header copies with the kernel
sources
- Fix relative include path to cs-etm.h
* tag 'perf-tools-fixes-for-v6.4-2-2023-05-30' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf evsel: Separate bpf_counter_list and bpf_filters, can be used at the same time
tools headers UAPI: Sync the linux/in.h with the kernel sources
perf cs-etm: Copy kernel coresight-pmu.h header
perf bpf: Do not use llvm-strip on BPF binary
perf build: Don't compile demangle-cxx.cpp if not necessary
perf arm: Fix include path to cs-etm.h
perf bpf filter: Fix a broken perf sample data naming for BPF CO-RE
perf ftrace latency: Remove unnecessary "--" from --use-nsec option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"The most important fix here is for missing dropping of the RCU read
lock when syncing maple tree register caches, the physical devices I
have that use the code don't do any syncing so I'd only ever tested
this with virtual devices and missed the fact that we need to drop the
lock in order to write to buses that need to sleep.
Otherwise there's a fix for an edge case when splitting up large batch
writes which has been lurking for a long time, a check to make sure
nobody writes new drivers with a bug that was found in several
SoundWire drivers and a tweak to the way the new kunit tests are
enabled to ensure they don't cause regmap to be enabled when it
wouldn't otherwise be"
* tag 'regmap-fix-v6.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: maple: Drop the RCU read lock while syncing registers
regmap: sdw: check for invalid multi-register writes config
regmap: Account for register length when chunking
regmap: REGMAP_KUNIT should not select REGMAP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull modules fix from Luis Chamberlain:
"A fix is provided for ia64. Even though ia64 is on life support it
helps to fix issues if we can. Thanks to Linus for doing tons of the
ia64 debugging"
* tag 'modules-6.4-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux:
module: fix module load for ia64
|
|
In commit a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting
r/w until quota is re-enabled") we defer clearing tyhe SB_RDONLY flag
in struct super. However, we didn't defer when we checked sb_rdonly()
to determine the lazy itable init thread should be enabled, with the
next result that the lazy inode table initialization would not be
properly started. This can cause generic/231 to fail in ext4's
nojournal mode.
Fix this by moving when we decide to start or stop the lazy itable
init thread to after we clear the SB_RDONLY flag when we are
remounting the file system read/write.
Fixes a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting r/w until...")
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230527035729.1001605-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Commit e360c6ed7274 ("ext4: Drop special handling of journalled data
from ext4_sync_file()") simplified ext4_sync_file() by dropping special
handling of journalled data mode as it was not needed anymore. However
that branch was also used for directories and symlinks and since the
fastcommit code does not track metadata changes to non-regular files, the
change has caused e.g. fsync(2) on directories to not commit transaction
as it should. Fix the problem by adding handling for non-regular files.
Fixes: e360c6ed7274 ("ext4: Drop special handling of journalled data from ext4_sync_file()")
Reported-by: Eric Whitney <enwlinux@gmail.com>
Link: https://lore.kernel.org/all/ZFqO3xVnmhL7zv1x@debian-BULLSEYE-live-builder-AMD64
Signed-off-by: Jan Kara <jack@suse.cz>
Tested-by: Eric Whitney <enwlinux@gmail.com>
Link: https://lore.kernel.org/r/20230524104453.8734-1-jack@suse.cz
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Treat i_data_sem for ea_inodes as being in their own lockdep class to
avoid lockdep complaints about ext4_setattr's use of inode_lock() on
normal inodes potentially causing lock ordering with i_data_sem on
ea_inodes in ext4_xattr_inode_write(). However, ea_inodes will be
operated on by ext4_setattr(), so this isn't a problem.
Cc: stable@kernel.org
Link: https://syzkaller.appspot.com/bug?extid=298c5d8fb4a128bc27b0
Reported-by: syzbot+298c5d8fb4a128bc27b0@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230524034951.779531-5-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
An ea_inode stores the value of an extended attribute; it can not have
extended attributes itself, or this will cause recursive nightmares.
Add a check in ext4_iget() to make sure this is the case.
Cc: stable@kernel.org
Reported-by: syzbot+e44749b6ba4d0434cd47@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230524034951.779531-4-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
If the ea_inode has been pushed out of the inode cache while there is
still a reference in the mb_cache, the lockdep subclass will not be
set on the inode, which can lead to some lockdep false positives.
Fixes: 33d201e0277b ("ext4: fix lockdep warning about recursive inode locking")
Cc: stable@kernel.org
Reported-by: syzbot+d4b971e744b1f5439336@syzkaller.appspotmail.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Link: https://lore.kernel.org/r/20230524034951.779531-3-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
