iio: proximity: sx_common: Add old register mapping

Older firmwares still send sensor configuration using a list of
registers with opaque values defined during sensor tuning.
sx9234 and sx9360 sensor on ACPI based devices are concerned.
More schema to configure the sensors will be needed to support devices
designed for windows, like Samsung Galaxy Book2.

Support schema is: "<_HID>.<register_name>". For instance
"STH9324,reg_adv_ctrl2" in:

    Scope (\_SB.PCI0.I2C2)
    {
        Device (SX28)
        {
            Name (_HID, "STH9324")  // _HID: Hardware ID
...
            Name (_DSD, Package (0x02)  // _DSD: Device-Specific Data
            {
                ToUUID ("daffd814-6eba-4d8c-8a91-bc9bbf4aa301") /*
Device Properties for _DSD */,
                Package (0x3F)
                {
...
                    Package (0x02)
                    {
                        "STH9324,reg_adv_ctrl2",
                        Zero
                    },`

Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230211002421.3447060-1-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

4 files changed, 92 insertions, 62 deletions

diff --git a/drivers/iio/proximity/sx9324.c b/drivers/iio/proximity/sx9324.c
index 977cf17cec52b..9a40ca32bb1ca 100644
--- a/drivers/iio/proximity/sx9324.c
+++ b/drivers/iio/proximity/sx9324.c
@@ -783,73 +783,75 @@ static int sx9324_write_raw(struct iio_dev *indio_dev,
 
 static const struct sx_common_reg_default sx9324_default_regs[] = {
 	{ SX9324_REG_IRQ_MSK, 0x00 },
-	{ SX9324_REG_IRQ_CFG0, 0x00 },
-	{ SX9324_REG_IRQ_CFG1, SX9324_REG_IRQ_CFG1_FAILCOND },
-	{ SX9324_REG_IRQ_CFG2, 0x00 },
-	{ SX9324_REG_GNRL_CTRL0, SX9324_REG_GNRL_CTRL0_SCANPERIOD_100MS },
+	{ SX9324_REG_IRQ_CFG0, 0x00, "irq_cfg0" },
+	{ SX9324_REG_IRQ_CFG1, SX9324_REG_IRQ_CFG1_FAILCOND, "irq_cfg1" },
+	{ SX9324_REG_IRQ_CFG2, 0x00, "irq_cfg2" },
+	{ SX9324_REG_GNRL_CTRL0, SX9324_REG_GNRL_CTRL0_SCANPERIOD_100MS, "gnrl_ctrl0" },
 	/*
 	 * The lower 4 bits should not be set as it enable sensors measurements.
 	 * Turning the detection on before the configuration values are set to
 	 * good values can cause the device to return erroneous readings.
 	 */
-	{ SX9324_REG_GNRL_CTRL1, SX9324_REG_GNRL_CTRL1_PAUSECTRL },
+	{ SX9324_REG_GNRL_CTRL1, SX9324_REG_GNRL_CTRL1_PAUSECTRL, "gnrl_ctrl1" },
 
-	{ SX9324_REG_AFE_CTRL0, SX9324_REG_AFE_CTRL0_RINT_LOWEST },
-	{ SX9324_REG_AFE_CTRL3, 0x00 },
+	{ SX9324_REG_AFE_CTRL0, SX9324_REG_AFE_CTRL0_RINT_LOWEST, "afe_ctrl0" },
+	{ SX9324_REG_AFE_CTRL3, 0x00, "afe_ctrl3" },
 	{ SX9324_REG_AFE_CTRL4, SX9324_REG_AFE_CTRL4_FREQ_83_33HZ |
-		SX9324_REG_AFE_CTRL4_RES_100 },
-	{ SX9324_REG_AFE_CTRL6, 0x00 },
+		SX9324_REG_AFE_CTRL4_RES_100, "afe_ctrl4" },
+	{ SX9324_REG_AFE_CTRL6, 0x00, "afe_ctrl6" },
 	{ SX9324_REG_AFE_CTRL7, SX9324_REG_AFE_CTRL4_FREQ_83_33HZ |
-		SX9324_REG_AFE_CTRL4_RES_100 },
+		SX9324_REG_AFE_CTRL4_RES_100, "afe_ctrl7" },
 
 	/* TODO(gwendal): PHx use chip default or all grounded? */
-	{ SX9324_REG_AFE_PH0, 0x29 },
-	{ SX9324_REG_AFE_PH1, 0x26 },
-	{ SX9324_REG_AFE_PH2, 0x1a },
-	{ SX9324_REG_AFE_PH3, 0x16 },
+	{ SX9324_REG_AFE_PH0, 0x29, "afe_ph0" },
+	{ SX9324_REG_AFE_PH1, 0x26, "afe_ph1" },
+	{ SX9324_REG_AFE_PH2, 0x1a, "afe_ph2" },
+	{ SX9324_REG_AFE_PH3, 0x16, "afe_ph3" },
 
 	{ SX9324_REG_AFE_CTRL8, SX9324_REG_AFE_CTRL8_RESERVED |
-		SX9324_REG_AFE_CTRL8_RESFILTIN_4KOHM },
-	{ SX9324_REG_AFE_CTRL9, SX9324_REG_AFE_CTRL9_AGAIN_1 },
+		SX9324_REG_AFE_CTRL8_RESFILTIN_4KOHM, "afe_ctrl8" },
+	{ SX9324_REG_AFE_CTRL9, SX9324_REG_AFE_CTRL9_AGAIN_1, "afe_ctrl9" },
 
 	{ SX9324_REG_PROX_CTRL0,
 		SX9324_REG_PROX_CTRL0_GAIN_1 << SX9324_REG_PROX_CTRL0_GAIN_SHIFT |
-		SX9324_REG_PROX_CTRL0_RAWFILT_1P50 },
+		SX9324_REG_PROX_CTRL0_RAWFILT_1P50, "prox_ctrl0" },
 	{ SX9324_REG_PROX_CTRL1,
 		SX9324_REG_PROX_CTRL0_GAIN_1 << SX9324_REG_PROX_CTRL0_GAIN_SHIFT |
-		SX9324_REG_PROX_CTRL0_RAWFILT_1P50 },
-	{ SX9324_REG_PROX_CTRL2, SX9324_REG_PROX_CTRL2_AVGNEG_THRESH_16K },
+		SX9324_REG_PROX_CTRL0_RAWFILT_1P50, "prox_ctrl1" },
+	{ SX9324_REG_PROX_CTRL2, SX9324_REG_PROX_CTRL2_AVGNEG_THRESH_16K, "prox_ctrl2" },
 	{ SX9324_REG_PROX_CTRL3, SX9324_REG_PROX_CTRL3_AVGDEB_2SAMPLES |
-		SX9324_REG_PROX_CTRL3_AVGPOS_THRESH_16K },
+		SX9324_REG_PROX_CTRL3_AVGPOS_THRESH_16K, "prox_ctrl3" },
 	{ SX9324_REG_PROX_CTRL4, SX9324_REG_PROX_CTRL4_AVGNEG_FILT_2 |
-		SX9324_REG_PROX_CTRL4_AVGPOS_FILT_256 },
-	{ SX9324_REG_PROX_CTRL5, 0x00 },
-	{ SX9324_REG_PROX_CTRL6, SX9324_REG_PROX_CTRL6_PROXTHRESH_32 },
-	{ SX9324_REG_PROX_CTRL7, SX9324_REG_PROX_CTRL6_PROXTHRESH_32 },
-	{ SX9324_REG_ADV_CTRL0, 0x00 },
-	{ SX9324_REG_ADV_CTRL1, 0x00 },
-	{ SX9324_REG_ADV_CTRL2, 0x00 },
-	{ SX9324_REG_ADV_CTRL3, 0x00 },
-	{ SX9324_REG_ADV_CTRL4, 0x00 },
+		SX9324_REG_PROX_CTRL4_AVGPOS_FILT_256, "prox_ctrl4" },
+	{ SX9324_REG_PROX_CTRL5, 0x00, "prox_ctrl5" },
+	{ SX9324_REG_PROX_CTRL6, SX9324_REG_PROX_CTRL6_PROXTHRESH_32, "prox_ctrl6" },
+	{ SX9324_REG_PROX_CTRL7, SX9324_REG_PROX_CTRL6_PROXTHRESH_32, "prox_ctrl7" },
+	{ SX9324_REG_ADV_CTRL0, 0x00, "adv_ctrl0" },
+	{ SX9324_REG_ADV_CTRL1, 0x00, "adv_ctrl1" },
+	{ SX9324_REG_ADV_CTRL2, 0x00, "adv_ctrl2" },
+	{ SX9324_REG_ADV_CTRL3, 0x00, "adv_ctrl3" },
+	{ SX9324_REG_ADV_CTRL4, 0x00, "adv_ctrl4" },
 	{ SX9324_REG_ADV_CTRL5, SX9324_REG_ADV_CTRL5_STARTUP_SENSOR_1 |
-		SX9324_REG_ADV_CTRL5_STARTUP_METHOD_1 },
-	{ SX9324_REG_ADV_CTRL6, 0x00 },
-	{ SX9324_REG_ADV_CTRL7, 0x00 },
-	{ SX9324_REG_ADV_CTRL8, 0x00 },
-	{ SX9324_REG_ADV_CTRL9, 0x00 },
+		SX9324_REG_ADV_CTRL5_STARTUP_METHOD_1, "adv_ctrl5" },
+	{ SX9324_REG_ADV_CTRL6, 0x00, "adv_ctrl6" },
+	{ SX9324_REG_ADV_CTRL7, 0x00, "adv_ctrl7" },
+	{ SX9324_REG_ADV_CTRL8, 0x00, "adv_ctrl8" },
+	{ SX9324_REG_ADV_CTRL9, 0x00, "adv_ctrl9" },
 	/* Body/Table threshold */
-	{ SX9324_REG_ADV_CTRL10, 0x00 },
-	{ SX9324_REG_ADV_CTRL11, 0x00 },
-	{ SX9324_REG_ADV_CTRL12, 0x00 },
+	{ SX9324_REG_ADV_CTRL10, 0x00, "adv_ctrl10" },
+	{ SX9324_REG_ADV_CTRL11, 0x00, "adv_ctrl11" },
+	{ SX9324_REG_ADV_CTRL12, 0x00, "adv_ctrl12" },
 	/* TODO(gwendal): SAR currenly disabled */
-	{ SX9324_REG_ADV_CTRL13, 0x00 },
-	{ SX9324_REG_ADV_CTRL14, 0x00 },
-	{ SX9324_REG_ADV_CTRL15, 0x00 },
-	{ SX9324_REG_ADV_CTRL16, 0x00 },
-	{ SX9324_REG_ADV_CTRL17, 0x00 },
-	{ SX9324_REG_ADV_CTRL18, 0x00 },
-	{ SX9324_REG_ADV_CTRL19, SX9324_REG_ADV_CTRL19_HIGHT_FAILURE_THRESH_SATURATION },
-	{ SX9324_REG_ADV_CTRL20, SX9324_REG_ADV_CTRL19_HIGHT_FAILURE_THRESH_SATURATION },
+	{ SX9324_REG_ADV_CTRL13, 0x00, "adv_ctrl13" },
+	{ SX9324_REG_ADV_CTRL14, 0x00, "adv_ctrl14" },
+	{ SX9324_REG_ADV_CTRL15, 0x00, "adv_ctrl15" },
+	{ SX9324_REG_ADV_CTRL16, 0x00, "adv_ctrl16" },
+	{ SX9324_REG_ADV_CTRL17, 0x00, "adv_ctrl17" },
+	{ SX9324_REG_ADV_CTRL18, 0x00, "adv_ctrl18" },
+	{ SX9324_REG_ADV_CTRL19,
+		SX9324_REG_ADV_CTRL19_HIGHT_FAILURE_THRESH_SATURATION, "adv_ctrl19" },
+	{ SX9324_REG_ADV_CTRL20,
+		SX9324_REG_ADV_CTRL19_HIGHT_FAILURE_THRESH_SATURATION, "adv_ctrl20" },
 };
 
 /* Activate all channels and perform an initial compensation. */
@@ -889,13 +891,15 @@ sx9324_get_default_reg(struct device *dev, int idx,
 	const char *res;
 
 	memcpy(reg_def, &sx9324_default_regs[idx], sizeof(*reg_def));
+
+	sx_common_get_raw_register_config(dev, reg_def);
 	switch (reg_def->reg) {
 	case SX9324_REG_AFE_PH0:
 	case SX9324_REG_AFE_PH1:
 	case SX9324_REG_AFE_PH2:
 	case SX9324_REG_AFE_PH3:
 		ph = reg_def->reg - SX9324_REG_AFE_PH0;
-		scnprintf(prop, ARRAY_SIZE(prop), "semtech,ph%d-pin", ph);
+		snprintf(prop, ARRAY_SIZE(prop), "semtech,ph%d-pin", ph);
 
 		count = device_property_count_u32(dev, prop);
 		if (count != ARRAY_SIZE(pin_defs))
diff --git a/drivers/iio/proximity/sx9360.c b/drivers/iio/proximity/sx9360.c
index 6e19d22e6a015..a50d9176411a1 100644
--- a/drivers/iio/proximity/sx9360.c
+++ b/drivers/iio/proximity/sx9360.c
@@ -663,37 +663,37 @@ static int sx9360_write_raw(struct iio_dev *indio_dev,
 
 static const struct sx_common_reg_default sx9360_default_regs[] = {
 	{ SX9360_REG_IRQ_MSK, 0x00 },
-	{ SX9360_REG_IRQ_CFG, 0x00 },
+	{ SX9360_REG_IRQ_CFG, 0x00, "irq_cfg" },
 	/*
 	 * The lower 2 bits should not be set as it enable sensors measurements.
 	 * Turning the detection on before the configuration values are set to
 	 * good values can cause the device to return erroneous readings.
 	 */
-	{ SX9360_REG_GNRL_CTRL0, 0x00 },
-	{ SX9360_REG_GNRL_CTRL1, 0x00 },
-	{ SX9360_REG_GNRL_CTRL2, SX9360_REG_GNRL_CTRL2_PERIOD_102MS },
+	{ SX9360_REG_GNRL_CTRL0, 0x00, "gnrl_ctrl0" },
+	{ SX9360_REG_GNRL_CTRL1, 0x00, "gnrl_ctrl1" },
+	{ SX9360_REG_GNRL_CTRL2, SX9360_REG_GNRL_CTRL2_PERIOD_102MS, "gnrl_ctrl2" },
 
-	{ SX9360_REG_AFE_CTRL1, SX9360_REG_AFE_CTRL1_RESFILTIN_0OHMS },
+	{ SX9360_REG_AFE_CTRL1, SX9360_REG_AFE_CTRL1_RESFILTIN_0OHMS, "afe_ctrl0" },
 	{ SX9360_REG_AFE_PARAM0_PHR, SX9360_REG_AFE_PARAM0_RSVD |
-		SX9360_REG_AFE_PARAM0_RESOLUTION_128 },
+		SX9360_REG_AFE_PARAM0_RESOLUTION_128, "afe_param0_phr" },
 	{ SX9360_REG_AFE_PARAM1_PHR, SX9360_REG_AFE_PARAM1_AGAIN_PHM_6PF |
-		SX9360_REG_AFE_PARAM1_FREQ_83_33HZ },
+		SX9360_REG_AFE_PARAM1_FREQ_83_33HZ, "afe_param1_phr" },
 	{ SX9360_REG_AFE_PARAM0_PHM, SX9360_REG_AFE_PARAM0_RSVD |
-		SX9360_REG_AFE_PARAM0_RESOLUTION_128 },
+		SX9360_REG_AFE_PARAM0_RESOLUTION_128, "afe_param0_phm" },
 	{ SX9360_REG_AFE_PARAM1_PHM, SX9360_REG_AFE_PARAM1_AGAIN_PHM_6PF |
-		SX9360_REG_AFE_PARAM1_FREQ_83_33HZ },
+		SX9360_REG_AFE_PARAM1_FREQ_83_33HZ, "afe_param1_phm" },
 
 	{ SX9360_REG_PROX_CTRL0_PHR, SX9360_REG_PROX_CTRL0_GAIN_1 |
-		SX9360_REG_PROX_CTRL0_RAWFILT_1P50 },
+		SX9360_REG_PROX_CTRL0_RAWFILT_1P50, "prox_ctrl0_phr" },
 	{ SX9360_REG_PROX_CTRL0_PHM, SX9360_REG_PROX_CTRL0_GAIN_1 |
-		SX9360_REG_PROX_CTRL0_RAWFILT_1P50 },
-	{ SX9360_REG_PROX_CTRL1, SX9360_REG_PROX_CTRL1_AVGNEG_THRESH_16K },
+		SX9360_REG_PROX_CTRL0_RAWFILT_1P50, "prox_ctrl0_phm" },
+	{ SX9360_REG_PROX_CTRL1, SX9360_REG_PROX_CTRL1_AVGNEG_THRESH_16K, "prox_ctrl1" },
 	{ SX9360_REG_PROX_CTRL2, SX9360_REG_PROX_CTRL2_AVGDEB_2SAMPLES |
-		SX9360_REG_PROX_CTRL2_AVGPOS_THRESH_16K },
+		SX9360_REG_PROX_CTRL2_AVGPOS_THRESH_16K, "prox_ctrl2" },
 	{ SX9360_REG_PROX_CTRL3, SX9360_REG_PROX_CTRL3_AVGNEG_FILT_2 |
-		SX9360_REG_PROX_CTRL3_AVGPOS_FILT_256 },
-	{ SX9360_REG_PROX_CTRL4, 0x00 },
-	{ SX9360_REG_PROX_CTRL5, SX9360_REG_PROX_CTRL5_PROXTHRESH_32 },
+		SX9360_REG_PROX_CTRL3_AVGPOS_FILT_256, "prox_ctrl3" },
+	{ SX9360_REG_PROX_CTRL4, 0x00, "prox_ctrl4" },
+	{ SX9360_REG_PROX_CTRL5, SX9360_REG_PROX_CTRL5_PROXTHRESH_32, "prox_ctrl5" },
 };
 
 /* Activate all channels and perform an initial compensation. */
diff --git a/drivers/iio/proximity/sx_common.c b/drivers/iio/proximity/sx_common.c
index eba9256730ec1..fe07d1444ac37 100644
--- a/drivers/iio/proximity/sx_common.c
+++ b/drivers/iio/proximity/sx_common.c
@@ -424,6 +424,27 @@ static const struct iio_buffer_setup_ops sx_common_buffer_setup_ops = {
 	.postdisable = sx_common_buffer_postdisable,
 };
 
+void sx_common_get_raw_register_config(struct device *dev,
+				       struct sx_common_reg_default *reg_def)
+{
+#ifdef CONFIG_ACPI
+	struct acpi_device *adev = ACPI_COMPANION(dev);
+	u32 raw = 0, ret;
+	char prop[80];
+
+	if (!reg_def->property || !adev)
+		return;
+
+	snprintf(prop, ARRAY_SIZE(prop), "%s,reg_%s", acpi_device_hid(adev), reg_def->property);
+	ret = device_property_read_u32(dev, prop, &raw);
+	if (ret)
+		return;
+
+	reg_def->def = raw;
+#endif
+}
+EXPORT_SYMBOL_NS_GPL(sx_common_get_raw_register_config, SEMTECH_PROX);
+
 #define SX_COMMON_SOFT_RESET				0xde
 
 static int sx_common_init_device(struct device *dev, struct iio_dev *indio_dev)
diff --git a/drivers/iio/proximity/sx_common.h b/drivers/iio/proximity/sx_common.h
index a2bbdef200d10..101b90e52ff26 100644
--- a/drivers/iio/proximity/sx_common.h
+++ b/drivers/iio/proximity/sx_common.h
@@ -8,6 +8,7 @@
 #ifndef IIO_SX_COMMON_H
 #define IIO_SX_COMMON_H
 
+#include <linux/acpi.h>
 #include <linux/iio/iio.h>
 #include <linux/iio/types.h>
 #include <linux/regulator/consumer.h>
@@ -26,6 +27,7 @@ static_assert(SX_COMMON_MAX_NUM_CHANNELS < BITS_PER_LONG);
 struct sx_common_reg_default {
 	u8 reg;
 	u8 def;
+	const char *property;
 };
 
 /**
@@ -148,6 +150,9 @@ int sx_common_probe(struct i2c_client *client,
 		    const struct sx_common_chip_info *chip_info,
 		    const struct regmap_config *regmap_config);
 
+void sx_common_get_raw_register_config(struct device *dev,
+				       struct sx_common_reg_default *reg_def);
+
 /* 3 is the number of events defined by a single phase. */
 extern const struct iio_event_spec sx_common_events[3];