#
# wan devices configuration
#

mainmenu_option next_comment
comment 'Wan interfaces'

bool 'Wan interfaces support' CONFIG_WAN
if [ "$CONFIG_WAN" = "y" ]; then
# There is no way to detect a comtrol sv11 - force it modular for now.

   dep_tristate '  Comtrol Hostess SV-11 support' CONFIG_HOSTESS_SV11 m

# The COSA/SRP driver has not been tested as non-modular yet.

   dep_tristate '  COSA/SRP sync serial boards support' CONFIG_COSA m

#
# COMX drivers
#

   tristate '  MultiGate (COMX) synchronous serial boards support' CONFIG_COMX
   if [ "$CONFIG_COMX" != "n" ]; then
      dep_tristate '    Support for COMX/CMX/HiCOMX boards' CONFIG_COMX_HW_COMX $CONFIG_COMX
      dep_tristate '    Support for LoCOMX board' CONFIG_COMX_HW_LOCOMX $CONFIG_COMX
      dep_tristate '    Support for MixCOM board' CONFIG_COMX_HW_MIXCOM $CONFIG_COMX
      dep_tristate '    Support for HDLC and syncPPP protocols on MultiGate boards' CONFIG_COMX_PROTO_PPP $CONFIG_COMX
      if [ "$CONFIG_LAPB" = "y" ]; then
	 dep_tristate '    Support for LAPB protocol on MultiGate boards' CONFIG_COMX_PROTO_LAPB $CONFIG_COMX
      fi
      if [ "$CONFIG_LAPB" = "m" ]; then
	 dep_tristate '    Support for LAPB protocol on MultiGate boards' CONFIG_COMX_PROTO_LAPB $CONFIG_LAPB
      fi
      dep_tristate '    Support for Frame Relay on MultiGate boards' CONFIG_COMX_PROTO_FR $CONFIG_COMX
   fi
#
# The Etinc driver has not been tested as non-modular yet.
#

   dep_tristate '  Etinc PCISYNC serial board support (EXPERIMENTAL)' CONFIG_DSCC4 m

# FarSite Communications' cards

   tristate '  FarSync T-Series X.21 (and V.35/V.24) cards' CONFIG_FARSYNC

#
# Lan Media's board. Currently 1000, 1200, 5200, 5245
#

   tristate '  LanMedia Corp. SSI/V.35, T1/E1, HSSI, T3 boards' CONFIG_LANMEDIA

# There is no way to detect a Sealevel board. Force it modular

   dep_tristate '  Sealevel Systems 4021 support' CONFIG_SEALEVEL_4021 m

   tristate '  SyncLink HDLC/SYNCPPP support' CONFIG_SYNCLINK_SYNCPPP

   tristate '  Generic HDLC driver' CONFIG_HDLC
   if [ "$CONFIG_HDLC" != "n" ]; then
      bool '    Synchronous Point-to-Point Protocol (PPP) support' CONFIG_HDLC_PPP
      if [ "$CONFIG_LAPB" = "m" -a "$CONFIG_HDLC" = "m" -o "$CONFIG_LAPB" = "y" ]; then
	 bool '    X.25 protocol support' CONFIG_HDLC_X25
      else
	 comment '    X.25/LAPB support is disabled'
      fi
      dep_tristate '    SDL RISCom/N2 support' CONFIG_N2 $CONFIG_HDLC
      dep_tristate '    Moxa C101 support' CONFIG_C101 $CONFIG_HDLC
   fi

   tristate '  Frame relay DLCI support' CONFIG_DLCI
   if [ "$CONFIG_DLCI" != "n" ]; then
      int '    Max open DLCI' CONFIG_DLCI_COUNT 24
      int '    Max DLCI per device' CONFIG_DLCI_MAX 8
      dep_tristate '    SDLA (Sangoma S502/S508) support' CONFIG_SDLA $CONFIG_DLCI
   fi

# Wan router core.

   if [ "$CONFIG_WAN_ROUTER" != "n" ]; then
      bool '  WAN router drivers' CONFIG_WAN_ROUTER_DRIVERS
      if [ "$CONFIG_WAN_ROUTER_DRIVERS" = "y" ]; then
	 dep_tristate '    Sangoma WANPIPE(tm) multiprotocol cards' CONFIG_VENDOR_SANGOMA $CONFIG_WAN_ROUTER
	 if [ "$CONFIG_VENDOR_SANGOMA" != "n" ]; then
	    bool '      WANPIPE Cisco HDLC support' CONFIG_WANPIPE_CHDLC
	    bool '      WANPIPE Frame Relay support' CONFIG_WANPIPE_FR
	    bool '      WANPIPE X.25 support' CONFIG_WANPIPE_X25
	    bool '      WANPIPE PPP support' CONFIG_WANPIPE_PPP
	    bool '      WANPIPE Multi-Port PPP support' CONFIG_WANPIPE_MULTPPP
	 fi
	 if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
	    dep_tristate '    Cyclom 2X(tm) cards (EXPERIMENTAL)' CONFIG_CYCLADES_SYNC $CONFIG_WAN_ROUTER_DRIVERS
	    if [ "$CONFIG_CYCLADES_SYNC" != "n" ]; then
	       bool '      Cyclom 2X X.25 support' CONFIG_CYCLOMX_X25
	    fi
	 fi
      fi
   fi


# X.25 network drivers

   if [ "$CONFIG_EXPERIMENTAL" = "y" ]; then
      dep_tristate '  LAPB over Ethernet driver (EXPERIMENTAL)' CONFIG_LAPBETHER $CONFIG_LAPB $CONFIG_X25
      dep_tristate '  X.25 async driver (EXPERIMENTAL)' CONFIG_X25_ASY $CONFIG_LAPB $CONFIG_X25
   fi

   if [ "$CONFIG_X86" = "y" ]; then
      tristate '  Granch SBNI12 Leased Line adapter support' CONFIG_SBNI
      if [ "$CONFIG_SBNI" != "n" ]; then
         bool '    Multiple line feature support' CONFIG_SBNI_MULTILINE
      fi
   fi
fi

endmenu