/* * linux/drivers/ide/trm290.c Version 1.02 Mar. 18, 2000 * * Copyright (c) 1997-1998 Mark Lord * May be copied or modified under the terms of the GNU General Public License */ /* * This module provides support for the bus-master IDE DMA function * of the Tekram TRM290 chip, used on a variety of PCI IDE add-on boards, * including a "Precision Instruments" board. The TRM290 pre-dates * the sff-8038 standard (ide-dma.c) by a few months, and differs * significantly enough to warrant separate routines for some functions, * while re-using others from ide-dma.c. * * EXPERIMENTAL! It works for me (a sample of one). * * Works reliably for me in DMA mode (READs only), * DMA WRITEs are disabled by default (see #define below); * * DMA is not enabled automatically for this chipset, * but can be turned on manually (with "hdparm -d1") at run time. * * I need volunteers with "spare" drives for further testing * and development, and maybe to help figure out the peculiarities. * Even knowing the registers (below), some things behave strangely. */ #define TRM290_NO_DMA_WRITES /* DMA writes seem unreliable sometimes */ /* * TRM-290 PCI-IDE2 Bus Master Chip * ================================ * The configuration registers are addressed in normal I/O port space * and are used as follows: * * trm290_base depends on jumper settings, and is probed for by ide-dma.c * * trm290_base+2 when WRITTEN: chiptest register (byte, write-only) * bit7 must always be written as "1" * bits6-2 undefined * bit1 1=legacy_compatible_mode, 0=native_pci_mode * bit0 1=test_mode, 0=normal(default) * * trm290_base+2 when READ: status register (byte, read-only) * bits7-2 undefined * bit1 channel0 busmaster interrupt status 0=none, 1=asserted * bit0 channel0 interrupt status 0=none, 1=asserted * * trm290_base+3 Interrupt mask register * bits7-5 undefined * bit4 legacy_header: 1=present, 0=absent * bit3 channel1 busmaster interrupt status 0=none, 1=asserted (read only) * bit2 channel1 interrupt status 0=none, 1=asserted (read only) * bit1 channel1 interrupt mask: 1=masked, 0=unmasked(default) * bit0 channel0 interrupt mask: 1=masked, 0=unmasked(default) * * trm290_base+1 "CPR" Config Pointer Register (byte) * bit7 1=autoincrement CPR bits 2-0 after each access of CDR * bit6 1=min. 1 wait-state posted write cycle (default), 0=0 wait-state * bit5 0=enabled master burst access (default), 1=disable (write only) * bit4 PCI DEVSEL# timing select: 1=medium(default), 0=fast * bit3 0=primary IDE channel, 1=secondary IDE channel * bits2-0 register index for accesses through CDR port * * trm290_base+0 "CDR" Config Data Register (word) * two sets of seven config registers, * selected by CPR bit 3 (channel) and CPR bits 2-0 (index 0 to 6), * each index defined below: * * Index-0 Base address register for command block (word) * defaults: 0x1f0 for primary, 0x170 for secondary * * Index-1 general config register (byte) * bit7 1=DMA enable, 0=DMA disable * bit6 1=activate IDE_RESET, 0=no action (default) * bit5 1=enable IORDY, 0=disable IORDY (default) * bit4 0=16-bit data port(default), 1=8-bit (XT) data port * bit3 interrupt polarity: 1=active_low, 0=active_high(default) * bit2 power-saving-mode(?): 1=enable, 0=disable(default) (write only) * bit1 bus_master_mode(?): 1=enable, 0=disable(default) * bit0 enable_io_ports: 1=enable(default), 0=disable * * Index-2 read-ahead counter preload bits 0-7 (byte, write only) * bits7-0 bits7-0 of readahead count * * Index-3 read-ahead config register (byte, write only) * bit7 1=enable_readahead, 0=disable_readahead(default) * bit6 1=clear_FIFO, 0=no_action * bit5 undefined * bit4 mode4 timing control: 1=enable, 0=disable(default) * bit3 undefined * bit2 undefined * bits1-0 bits9-8 of read-ahead count * * Index-4 base address register for control block (word) * defaults: 0x3f6 for primary, 0x376 for secondary * * Index-5 data port timings (shared by both drives) (byte) * standard PCI "clk" (clock) counts, default value = 0xf5 * * bits7-6 setup time: 00=1clk, 01=2clk, 10=3clk, 11=4clk * bits5-3 hold time: 000=1clk, 001=2clk, 010=3clk, * 011=4clk, 100=5clk, 101=6clk, * 110=8clk, 111=12clk * bits2-0 active time: 000=2clk, 001=3clk, 010=4clk, * 011=5clk, 100=6clk, 101=8clk, * 110=12clk, 111=16clk * * Index-6 command/control port timings (shared by both drives) (byte) * same layout as Index-5, default value = 0xde * * Suggested CDR programming for PIO mode0 (600ns): * 0x01f0,0x21,0xff,0x80,0x03f6,0xf5,0xde ; primary * 0x0170,0x21,0xff,0x80,0x0376,0xf5,0xde ; secondary * * Suggested CDR programming for PIO mode3 (180ns): * 0x01f0,0x21,0xff,0x80,0x03f6,0x09,0xde ; primary * 0x0170,0x21,0xff,0x80,0x0376,0x09,0xde ; secondary * * Suggested CDR programming for PIO mode4 (120ns): * 0x01f0,0x21,0xff,0x80,0x03f6,0x00,0xde ; primary * 0x0170,0x21,0xff,0x80,0x0376,0x00,0xde ; secondary * */ #include #include #include #include #include #include #include #include #include #include #include #include #include static void trm290_prepare_drive (ide_drive_t *drive, unsigned int use_dma) { ide_hwif_t *hwif = HWIF(drive); unsigned int reg; unsigned long flags; /* select PIO or DMA */ reg = use_dma ? (0x21 | 0x82) : (0x21 & ~0x82); __save_flags(flags); /* local CPU only */ __cli(); /* local CPU only */ if (reg != hwif->select_data) { hwif->select_data = reg; outb(0x51|(hwif->channel<<3), hwif->config_data+1); /* set PIO/DMA */ outw(reg & 0xff, hwif->config_data); } /* enable IRQ if not probing */ if (drive->present) { reg = inw(hwif->config_data+3) & 0x13; reg &= ~(1 << hwif->channel); outw(reg, hwif->config_data+3); } __restore_flags(flags); /* local CPU only */ } static void trm290_selectproc (ide_drive_t *drive) { trm290_prepare_drive(drive, drive->using_dma); } #ifdef CONFIG_BLK_DEV_IDEDMA static int trm290_dmaproc (ide_dma_action_t func, ide_drive_t *drive) { ide_hwif_t *hwif = HWIF(drive); unsigned int count, reading = 2, writing = 0; switch (func) { case ide_dma_write: reading = 0; writing = 1; #ifdef TRM290_NO_DMA_WRITES break; /* always use PIO for writes */ #endif case ide_dma_read: if (!(count = ide_build_dmatable(drive, func))) break; /* try PIO instead of DMA */ trm290_prepare_drive(drive, 1); /* select DMA xfer */ outl(hwif->dmatable_dma|reading|writing, hwif->dma_base); drive->waiting_for_dma = 1; outw((count * 2) - 1, hwif->dma_base+2); /* start DMA */ if (drive->media != ide_disk) return 0; ide_set_handler(drive, &ide_dma_intr, WAIT_CMD, NULL); OUT_BYTE(reading ? WIN_READDMA : WIN_WRITEDMA, IDE_COMMAND_REG); return 0; case ide_dma_begin: return 0; case ide_dma_end: drive->waiting_for_dma = 0; ide_destroy_dmatable(drive); /* purge DMA mappings */ return (inw(hwif->dma_base+2) != 0x00ff); case ide_dma_test_irq: return (inw(hwif->dma_base+2) == 0x00ff); default: return ide_dmaproc(func, drive); } trm290_prepare_drive(drive, 0); /* select PIO xfer */ return 1; } #endif /* CONFIG_BLK_DEV_IDEDMA */ /* * Invoked from ide-dma.c at boot time. */ void __init ide_init_trm290 (ide_hwif_t *hwif) { unsigned int cfgbase = 0; unsigned long flags; byte reg; struct pci_dev *dev = hwif->pci_dev; hwif->chipset = ide_trm290; cfgbase = pci_resource_start(dev, 4); if ((dev->class & 5) && cfgbase) { hwif->config_data = cfgbase; printk("TRM290: chip config base at 0x%04lx\n", hwif->config_data); } else { hwif->config_data = 0x3df0; printk("TRM290: using default config base at 0x%04lx\n", hwif->config_data); } __save_flags(flags); /* local CPU only */ __cli(); /* local CPU only */ /* put config reg into first byte of hwif->select_data */ outb(0x51|(hwif->channel<<3), hwif->config_data+1); hwif->select_data = 0x21; /* select PIO as default */ outb(hwif->select_data, hwif->config_data); reg = inb(hwif->config_data+3); /* get IRQ info */ reg = (reg & 0x10) | 0x03; /* mask IRQs for both ports */ outb(reg, hwif->config_data+3); __restore_flags(flags); /* local CPU only */ if ((reg & 0x10)) hwif->irq = hwif->channel ? 15 : 14; /* legacy mode */ else if (!hwif->irq && hwif->mate && hwif->mate->irq) hwif->irq = hwif->mate->irq; /* sharing IRQ with mate */ ide_setup_dma(hwif, (hwif->config_data + 4) ^ (hwif->channel ? 0x0080 : 0x0000), 3); #ifdef CONFIG_BLK_DEV_IDEDMA hwif->dmaproc = &trm290_dmaproc; #endif /* CONFIG_BLK_DEV_IDEDMA */ hwif->selectproc = &trm290_selectproc; hwif->autodma = 0; /* play it safe for now */ #if 1 { /* * My trm290-based card doesn't seem to work with all possible values * for the control basereg, so this kludge ensures that we use only * values that are known to work. Ugh. -ml */ unsigned short old, compat = hwif->channel ? 0x374 : 0x3f4; static unsigned short next_offset = 0; outb(0x54|(hwif->channel<<3), hwif->config_data+1); old = inw(hwif->config_data) & ~1; if (old != compat && inb(old+2) == 0xff) { compat += (next_offset += 0x400); /* leave lower 10 bits untouched */ #if 1 if (ide_check_region(compat + 2, 1)) printk("Aieee %s: ide_check_region failure at 0x%04x\n", hwif->name, (compat + 2)); /* * The region check is not needed; however......... * Since this is the checked in ide-probe.c, * this is only an assignment. */ #endif hwif->io_ports[IDE_CONTROL_OFFSET] = compat + 2; outw(compat|1, hwif->config_data); printk("%s: control basereg workaround: old=0x%04x, new=0x%04x\n", hwif->name, old, inw(hwif->config_data) & ~1); } } #endif }