/* -------------------------------------------------------------------- i2c-ite.h: Global defines for the I2C controller on board the ITE MIPS processor. -------------------------------------------------------------------- Hai-Pao Fan, MontaVista Software, Inc. hpfan@mvista.com or source@mvista.com Copyright 2001 MontaVista Software Inc. * This program is free software; you can redistribute it and/or modify it * under the terms of the GNU General Public License as published by the * Free Software Foundation; either version 2 of the License, or (at your * option) any later version. * * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * * You should have received a copy of the GNU General Public License along * with this program; if not, write to the Free Software Foundation, Inc., * 675 Mass Ave, Cambridge, MA 02139, USA. */ #ifndef I2C_ITE_H #define I2C_ITE_H 1 #include /* I2C Registers */ #define ITE_I2CHCR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x30 #define ITE_I2CHSR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x34 #define ITE_I2CSAR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x38 #define ITE_I2CSSAR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x3c #define ITE_I2CCKCNT IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x48 #define ITE_I2CSHDR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x4c #define ITE_I2CRSUR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x50 #define ITE_I2CPSUR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x54 #define ITE_I2CFDR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x70 #define ITE_I2CFBCR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x74 #define ITE_I2CFCR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x78 #define ITE_I2CFSR IT8172_PCI_IO_BASE + IT_I2C_BASE + 0x7c /* Host Control Register ITE_I2CHCR */ #define ITE_I2CHCR_HCE 0x01 /* Enable I2C Host Controller */ #define ITE_I2CHCR_IE 0x02 /* Enable the interrupt after completing the current transaction */ #define ITE_I2CHCR_CP_W 0x00 /* bit2-4 000 - Write */ #define ITE_I2CHCR_CP_R 0x08 /* 010 - Current address read */ #define ITE_I2CHCR_CP_S 0x10 /* 100 - Sequential read */ #define ITE_I2CHCR_ST 0x20 /* Initiates the I2C host controller to execute the command and send the data programmed in all required registers to I2C bus */ #define ITE_CMD ITE_I2CHCR_HCE | ITE_I2CHCR_IE | ITE_I2CHCR_ST #define ITE_WRITE ITE_CMD | ITE_I2CHCR_CP_W #define ITE_READ ITE_CMD | ITE_I2CHCR_CP_R #define ITE_SREAD ITE_CMD | ITE_I2CHCR_CP_S /* Host Status Register ITE_I2CHSR */ #define ITE_I2CHSR_DB 0x01 /* Device is busy, receives NACK response except in the first and last bytes */ #define ITE_I2CHSR_DNE 0x02 /* Target address on I2C bus does not exist */ #define ITE_I2CHSR_TDI 0x04 /* R/W Transaction on I2C bus was completed */ #define ITE_I2CHSR_HB 0x08 /* Host controller is processing transactions */ #define ITE_I2CHSR_FER 0x10 /* Error occurs in the FIFO */ /* Slave Address Register ITE_I2CSAR */ #define ITE_I2CSAR_SA_MASK 0xfe /* Target I2C device address */ #define ITE_I2CSAR_ASO 0x0100 /* Output 1/0 to I2CAS port when the next slave address is addressed */ /* Slave Sub-address Register ITE_I2CSSAR */ #define ITE_I2CSSAR_SUBA_MASK 0xff /* Target I2C device sub-address */ /* Clock Counter Register ITE_I2CCKCNT */ #define ITE_I2CCKCNT_STOP 0x00 /* stop I2C clock */ #define ITE_I2CCKCNT_HPCC_MASK 0x7f /* SCL high period counter */ #define ITE_I2CCKCNT_LPCC_MASK 0x7f00 /* SCL low period counter */ /* START Hold Time Register ITE_I2CSHDR */ /* value is counted based on 16 MHz internal clock */ #define ITE_I2CSHDR_FM 0x0a /* START condition at fast mode */ #define ITE_I2CSHDR_SM 0x47 /* START contition at standard mode */ /* (Repeated) START Setup Time Register ITE_I2CRSUR */ /* value is counted based on 16 MHz internal clock */ #define ITE_I2CRSUR_FM 0x0a /* repeated START condition at fast mode */ #define ITE_I2CRSUR_SM 0x50 /* repeated START condition at standard mode */ /* STOP setup Time Register ITE_I2CPSUR */ /* FIFO Data Register ITE_I2CFDR */ #define ITE_I2CFDR_MASK 0xff /* FIFO Byte Count Register ITE_I2CFBCR */ #define ITE_I2CFBCR_MASK 0x3f /* FIFO Control Register ITE_I2CFCR */ #define ITE_I2CFCR_FLUSH 0x01 /* Flush FIFO and reset the FIFO point and I2CFSR */ /* FIFO Status Register ITE_I2CFSR */ #define ITE_I2CFSR_FO 0x01 /* FIFO is overrun when write */ #define ITE_I2CFSR_FU 0x02 /* FIFO is underrun when read */ #define ITE_I2CFSR_FF 0x04 /* FIFO is full when write */ #define ITE_I2CFSR_FE 0x08 /* FIFO is empty when read */ #endif /* I2C_ITE_H */