ChangeSet 1.1105, 2003/03/13 10:31:07-08:00, greg@kroah.com i2c: add bus driver for ALI15x3 devices This is from the i2c CVS tree. drivers/i2c/busses/Kconfig | 14 drivers/i2c/busses/Makefile | 1 drivers/i2c/busses/i2c-ali15x3.c | 587 +++++++++++++++++++++++++++++++++++++++ 3 files changed, 602 insertions(+) diff -Nru a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig --- a/drivers/i2c/busses/Kconfig Thu Mar 13 16:58:06 2003 +++ b/drivers/i2c/busses/Kconfig Thu Mar 13 16:58:06 2003 @@ -5,6 +5,20 @@ menu "I2C Hardware Sensors Mainboard support" +config I2C_ALI15X3 + tristate " ALI 15x3" + depends on I2C && I2C_PROC && PCI && EXPERIMENTAL + help + If you say yes to this option, support will be included for the + Acer Labs Inc. (ALI) M1514 and M1543 motherboard I2C interfaces. + + This can also be built as a module. If so, the module will be + called i2c-ali15x3. + + You will also need the latest user-space utilties: you can find them + in the lm_sensors package, which you can download at + http://www.lm-sensors.nu + config I2C_AMD756 tristate " AMD 756/766" depends on I2C && I2C_PROC diff -Nru a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile --- a/drivers/i2c/busses/Makefile Thu Mar 13 16:58:06 2003 +++ b/drivers/i2c/busses/Makefile Thu Mar 13 16:58:06 2003 @@ -2,5 +2,6 @@ # Makefile for the kernel hardware sensors bus drivers. # +obj-$(CONFIG_I2C_ALI15X3) += i2c-ali15x3.o obj-$(CONFIG_I2C_AMD756) += i2c-amd756.o obj-$(CONFIG_I2C_AMD8111) += i2c-amd8111.o diff -Nru a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c --- /dev/null Wed Dec 31 16:00:00 1969 +++ b/drivers/i2c/busses/i2c-ali15x3.c Thu Mar 13 16:58:06 2003 @@ -0,0 +1,587 @@ +/* + ali15x3.c - Part of lm_sensors, Linux kernel modules for hardware + monitoring + Copyright (c) 1999 Frodo Looijaard and + Philip Edelbrock and + Mark D. Studebaker + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +/* + This is the driver for the SMB Host controller on + Acer Labs Inc. (ALI) M1541 and M1543C South Bridges. + + The M1543C is a South bridge for desktop systems. + The M1533 is a South bridge for portable systems. + They are part of the following ALI chipsets: + "Aladdin Pro 2": Includes the M1621 Slot 1 North bridge + with AGP and 100MHz CPU Front Side bus + "Aladdin V": Includes the M1541 Socket 7 North bridge + with AGP and 100MHz CPU Front Side bus + "Aladdin IV": Includes the M1541 Socket 7 North bridge + with host bus up to 83.3 MHz. + For an overview of these chips see http://www.acerlabs.com + + The M1533/M1543C devices appear as FOUR separate devices + on the PCI bus. An output of lspci will show something similar + to the following: + + 00:02.0 USB Controller: Acer Laboratories Inc. M5237 + 00:03.0 Bridge: Acer Laboratories Inc. M7101 + 00:07.0 ISA bridge: Acer Laboratories Inc. M1533 + 00:0f.0 IDE interface: Acer Laboratories Inc. M5229 + + The SMB controller is part of the 7101 device, which is an + ACPI-compliant Power Management Unit (PMU). + + The whole 7101 device has to be enabled for the SMB to work. + You can't just enable the SMB alone. + The SMB and the ACPI have separate I/O spaces. + We make sure that the SMB is enabled. We leave the ACPI alone. + + This driver controls the SMB Host only. + The SMB Slave controller on the M15X3 is not enabled. + + This driver does not use interrupts. +*/ + +/* Note: we assume there can only be one ALI15X3, with one SMBus interface */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* ALI15X3 SMBus address offsets */ +#define SMBHSTSTS (0 + ali15x3_smba) +#define SMBHSTCNT (1 + ali15x3_smba) +#define SMBHSTSTART (2 + ali15x3_smba) +#define SMBHSTCMD (7 + ali15x3_smba) +#define SMBHSTADD (3 + ali15x3_smba) +#define SMBHSTDAT0 (4 + ali15x3_smba) +#define SMBHSTDAT1 (5 + ali15x3_smba) +#define SMBBLKDAT (6 + ali15x3_smba) + +/* PCI Address Constants */ +#define SMBCOM 0x004 +#define SMBBA 0x014 +#define SMBATPC 0x05B /* used to unlock xxxBA registers */ +#define SMBHSTCFG 0x0E0 +#define SMBSLVC 0x0E1 +#define SMBCLK 0x0E2 +#define SMBREV 0x008 + +/* Other settings */ +#define MAX_TIMEOUT 200 /* times 1/100 sec */ +#define ALI15X3_SMB_IOSIZE 32 + +/* this is what the Award 1004 BIOS sets them to on a ASUS P5A MB. + We don't use these here. If the bases aren't set to some value we + tell user to upgrade BIOS and we fail. +*/ +#define ALI15X3_SMB_DEFAULTBASE 0xE800 + +/* ALI15X3 address lock bits */ +#define ALI15X3_LOCK 0x06 + +/* ALI15X3 command constants */ +#define ALI15X3_ABORT 0x02 +#define ALI15X3_T_OUT 0x04 +#define ALI15X3_QUICK 0x00 +#define ALI15X3_BYTE 0x10 +#define ALI15X3_BYTE_DATA 0x20 +#define ALI15X3_WORD_DATA 0x30 +#define ALI15X3_BLOCK_DATA 0x40 +#define ALI15X3_BLOCK_CLR 0x80 + +/* ALI15X3 status register bits */ +#define ALI15X3_STS_IDLE 0x04 +#define ALI15X3_STS_BUSY 0x08 +#define ALI15X3_STS_DONE 0x10 +#define ALI15X3_STS_DEV 0x20 /* device error */ +#define ALI15X3_STS_COLL 0x40 /* collision or no response */ +#define ALI15X3_STS_TERM 0x80 /* terminated by abort */ +#define ALI15X3_STS_ERR 0xE0 /* all the bad error bits */ + + +/* If force_addr is set to anything different from 0, we forcibly enable + the device at the given address. */ +static int force_addr = 0; +MODULE_PARM(force_addr, "i"); +MODULE_PARM_DESC(force_addr, + "Initialize the base address of the i2c controller"); + + +static void ali15x3_do_pause(unsigned int amount); +static int ali15x3_transaction(void); + +static unsigned short ali15x3_smba = 0; + +/* Detect whether a ALI15X3 can be found, and initialize it, where necessary. + Note the differences between kernels with the old PCI BIOS interface and + newer kernels with the real PCI interface. In compat.h some things are + defined to make the transition easier. */ +int ali15x3_setup(void) +{ + u16 a; + unsigned char temp; + + struct pci_dev *ALI15X3_dev; + + /* First check whether we can access PCI at all */ + if (pci_present() == 0) { + printk("i2c-ali15x3.o: Error: No PCI-bus found!\n"); + return -ENODEV; + } + + /* Look for the ALI15X3, M7101 device */ + ALI15X3_dev = NULL; + ALI15X3_dev = pci_find_device(PCI_VENDOR_ID_AL, + PCI_DEVICE_ID_AL_M7101, ALI15X3_dev); + if (ALI15X3_dev == NULL) { + printk("i2c-ali15x3.o: Error: Can't detect ali15x3!\n"); + return -ENODEV; + } + +/* Check the following things: + - SMB I/O address is initialized + - Device is enabled + - We can use the addresses +*/ + +/* Unlock the register. + The data sheet says that the address registers are read-only + if the lock bits are 1, but in fact the address registers + are zero unless you clear the lock bits. +*/ + pci_read_config_byte(ALI15X3_dev, SMBATPC, &temp); + if (temp & ALI15X3_LOCK) { + temp &= ~ALI15X3_LOCK; + pci_write_config_byte(ALI15X3_dev, SMBATPC, temp); + } + +/* Determine the address of the SMBus area */ + pci_read_config_word(ALI15X3_dev, SMBBA, &ali15x3_smba); + ali15x3_smba &= (0xffff & ~(ALI15X3_SMB_IOSIZE - 1)); + if (ali15x3_smba == 0 && force_addr == 0) { + printk + ("i2c-ali15x3.o: ALI15X3_smb region uninitialized - upgrade BIOS or use force_addr=0xaddr\n"); + return -ENODEV; + } + + if(force_addr) + ali15x3_smba = force_addr & ~(ALI15X3_SMB_IOSIZE - 1); + + if (check_region(ali15x3_smba, ALI15X3_SMB_IOSIZE)) { + printk + ("i2c-ali15x3.o: ALI15X3_smb region 0x%x already in use!\n", + ali15x3_smba); + return -ENODEV; + } + + if(force_addr) { + printk("i2c-ali15x3.o: forcing ISA address 0x%04X\n", ali15x3_smba); + if (PCIBIOS_SUCCESSFUL != + pci_write_config_word(ALI15X3_dev, SMBBA, ali15x3_smba)) + return -ENODEV; + if (PCIBIOS_SUCCESSFUL != + pci_read_config_word(ALI15X3_dev, SMBBA, &a)) + return -ENODEV; + if ((a & ~(ALI15X3_SMB_IOSIZE - 1)) != ali15x3_smba) { + /* make sure it works */ + printk("i2c-ali15x3.o: force address failed - not supported?\n"); + return -ENODEV; + } + } +/* check if whole device is enabled */ + pci_read_config_byte(ALI15X3_dev, SMBCOM, &temp); + if ((temp & 1) == 0) { + printk("i2c-ali15x3: enabling SMBus device\n"); + pci_write_config_byte(ALI15X3_dev, SMBCOM, temp | 0x01); + } + +/* Is SMB Host controller enabled? */ + pci_read_config_byte(ALI15X3_dev, SMBHSTCFG, &temp); + if ((temp & 1) == 0) { + printk("i2c-ali15x3: enabling SMBus controller\n"); + pci_write_config_byte(ALI15X3_dev, SMBHSTCFG, temp | 0x01); + } + +/* set SMB clock to 74KHz as recommended in data sheet */ + pci_write_config_byte(ALI15X3_dev, SMBCLK, 0x20); + + /* Everything is happy, let's grab the memory and set things up. */ + request_region(ali15x3_smba, ALI15X3_SMB_IOSIZE, "ali15x3-smb"); + +#ifdef DEBUG +/* + The interrupt routing for SMB is set up in register 0x77 in the + 1533 ISA Bridge device, NOT in the 7101 device. + Don't bother with finding the 1533 device and reading the register. + if ((....... & 0x0F) == 1) + printk("i2c-ali15x3.o: ALI15X3 using Interrupt 9 for SMBus.\n"); +*/ + pci_read_config_byte(ALI15X3_dev, SMBREV, &temp); + printk("i2c-ali15x3.o: SMBREV = 0x%X\n", temp); + printk("i2c-ali15x3.o: ALI15X3_smba = 0x%X\n", ali15x3_smba); +#endif /* DEBUG */ + + return 0; +} + + +/* Internally used pause function */ +void ali15x3_do_pause(unsigned int amount) +{ + current->state = TASK_INTERRUPTIBLE; + schedule_timeout(amount); +} + +/* Another internally used function */ +int ali15x3_transaction(void) +{ + int temp; + int result = 0; + int timeout = 0; + +#ifdef DEBUG + printk + ("i2c-ali15x3.o: Transaction (pre): STS=%02x, CNT=%02x, CMD=%02x, ADD=%02x, DAT0=%02x, " + "DAT1=%02x\n", inb_p(SMBHSTSTS), inb_p(SMBHSTCNT), + inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0), + inb_p(SMBHSTDAT1)); +#endif + + /* get status */ + temp = inb_p(SMBHSTSTS); + + /* Make sure the SMBus host is ready to start transmitting */ + /* Check the busy bit first */ + if (temp & ALI15X3_STS_BUSY) { +/* + If the host controller is still busy, it may have timed out in the previous transaction, + resulting in a "SMBus Timeout" printk. + I've tried the following to reset a stuck busy bit. + 1. Reset the controller with an ABORT command. + (this doesn't seem to clear the controller if an external device is hung) + 2. Reset the controller and the other SMBus devices with a T_OUT command. + (this clears the host busy bit if an external device is hung, + but it comes back upon a new access to a device) + 3. Disable and reenable the controller in SMBHSTCFG + Worst case, nothing seems to work except power reset. +*/ +/* Abort - reset the host controller */ +/* +#ifdef DEBUG + printk("i2c-ali15x3.o: Resetting host controller to clear busy condition\n",temp); +#endif + outb_p(ALI15X3_ABORT, SMBHSTCNT); + temp = inb_p(SMBHSTSTS); + if (temp & ALI15X3_STS_BUSY) { +*/ + +/* + Try resetting entire SMB bus, including other devices - + This may not work either - it clears the BUSY bit but + then the BUSY bit may come back on when you try and use the chip again. + If that's the case you are stuck. +*/ + printk + ("i2c-ali15x3.o: Resetting entire SMB Bus to clear busy condition (%02x)\n", + temp); + outb_p(ALI15X3_T_OUT, SMBHSTCNT); + temp = inb_p(SMBHSTSTS); + } +/* + } +*/ + + /* now check the error bits and the busy bit */ + if (temp & (ALI15X3_STS_ERR | ALI15X3_STS_BUSY)) { + /* do a clear-on-write */ + outb_p(0xFF, SMBHSTSTS); + if ((temp = inb_p(SMBHSTSTS)) & + (ALI15X3_STS_ERR | ALI15X3_STS_BUSY)) { + /* this is probably going to be correctable only by a power reset + as one of the bits now appears to be stuck */ + /* This may be a bus or device with electrical problems. */ + printk + ("i2c-ali15x3.o: SMBus reset failed! (0x%02x) - controller or device on bus is probably hung\n", + temp); + return -1; + } + } else { + /* check and clear done bit */ + if (temp & ALI15X3_STS_DONE) { + outb_p(temp, SMBHSTSTS); + } + } + + /* start the transaction by writing anything to the start register */ + outb_p(0xFF, SMBHSTSTART); + + /* We will always wait for a fraction of a second! */ + timeout = 0; + do { + ali15x3_do_pause(1); + temp = inb_p(SMBHSTSTS); + } while ((!(temp & (ALI15X3_STS_ERR | ALI15X3_STS_DONE))) + && (timeout++ < MAX_TIMEOUT)); + + /* If the SMBus is still busy, we give up */ + if (timeout >= MAX_TIMEOUT) { + result = -1; + printk("i2c-ali15x3.o: SMBus Timeout!\n"); + } + + if (temp & ALI15X3_STS_TERM) { + result = -1; +#ifdef DEBUG + printk("i2c-ali15x3.o: Error: Failed bus transaction\n"); +#endif + } + +/* + Unfortunately the ALI SMB controller maps "no response" and "bus collision" + into a single bit. No reponse is the usual case so don't + do a printk. + This means that bus collisions go unreported. +*/ + if (temp & ALI15X3_STS_COLL) { + result = -1; +#ifdef DEBUG + printk + ("i2c-ali15x3.o: Error: no response or bus collision ADD=%02x\n", + inb_p(SMBHSTADD)); +#endif + } + +/* haven't ever seen this */ + if (temp & ALI15X3_STS_DEV) { + result = -1; + printk("i2c-ali15x3.o: Error: device error\n"); + } +#ifdef DEBUG + printk + ("i2c-ali15x3.o: Transaction (post): STS=%02x, CNT=%02x, CMD=%02x, ADD=%02x, " + "DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTSTS), inb_p(SMBHSTCNT), + inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0), + inb_p(SMBHSTDAT1)); +#endif + return result; +} + +/* Return -1 on error. */ +s32 ali15x3_access(struct i2c_adapter * adap, u16 addr, + unsigned short flags, char read_write, u8 command, + int size, union i2c_smbus_data * data) +{ + int i, len; + int temp; + int timeout; + +/* clear all the bits (clear-on-write) */ + outb_p(0xFF, SMBHSTSTS); +/* make sure SMBus is idle */ + temp = inb_p(SMBHSTSTS); + for (timeout = 0; + (timeout < MAX_TIMEOUT) && !(temp & ALI15X3_STS_IDLE); + timeout++) { + ali15x3_do_pause(1); + temp = inb_p(SMBHSTSTS); + } + if (timeout >= MAX_TIMEOUT) { + printk("i2c-ali15x3.o: Idle wait Timeout! STS=0x%02x\n", + temp); + } + + switch (size) { + case I2C_SMBUS_PROC_CALL: + printk + ("i2c-ali15x3.o: I2C_SMBUS_PROC_CALL not supported!\n"); + return -1; + case I2C_SMBUS_QUICK: + outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + SMBHSTADD); + size = ALI15X3_QUICK; + break; + case I2C_SMBUS_BYTE: + outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + SMBHSTADD); + if (read_write == I2C_SMBUS_WRITE) + outb_p(command, SMBHSTCMD); + size = ALI15X3_BYTE; + break; + case I2C_SMBUS_BYTE_DATA: + outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + SMBHSTADD); + outb_p(command, SMBHSTCMD); + if (read_write == I2C_SMBUS_WRITE) + outb_p(data->byte, SMBHSTDAT0); + size = ALI15X3_BYTE_DATA; + break; + case I2C_SMBUS_WORD_DATA: + outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + SMBHSTADD); + outb_p(command, SMBHSTCMD); + if (read_write == I2C_SMBUS_WRITE) { + outb_p(data->word & 0xff, SMBHSTDAT0); + outb_p((data->word & 0xff00) >> 8, SMBHSTDAT1); + } + size = ALI15X3_WORD_DATA; + break; + case I2C_SMBUS_BLOCK_DATA: + outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + SMBHSTADD); + outb_p(command, SMBHSTCMD); + if (read_write == I2C_SMBUS_WRITE) { + len = data->block[0]; + if (len < 0) { + len = 0; + data->block[0] = len; + } + if (len > 32) { + len = 32; + data->block[0] = len; + } + outb_p(len, SMBHSTDAT0); + outb_p(inb_p(SMBHSTCNT) | ALI15X3_BLOCK_CLR, SMBHSTCNT); /* Reset SMBBLKDAT */ + for (i = 1; i <= len; i++) + outb_p(data->block[i], SMBBLKDAT); + } + size = ALI15X3_BLOCK_DATA; + break; + } + + outb_p(size, SMBHSTCNT); /* output command */ + + if (ali15x3_transaction()) /* Error in transaction */ + return -1; + + if ((read_write == I2C_SMBUS_WRITE) || (size == ALI15X3_QUICK)) + return 0; + + + switch (size) { + case ALI15X3_BYTE: /* Result put in SMBHSTDAT0 */ + data->byte = inb_p(SMBHSTDAT0); + break; + case ALI15X3_BYTE_DATA: + data->byte = inb_p(SMBHSTDAT0); + break; + case ALI15X3_WORD_DATA: + data->word = inb_p(SMBHSTDAT0) + (inb_p(SMBHSTDAT1) << 8); + break; + case ALI15X3_BLOCK_DATA: + len = inb_p(SMBHSTDAT0); + if (len > 32) + len = 32; + data->block[0] = len; + outb_p(inb_p(SMBHSTCNT) | ALI15X3_BLOCK_CLR, SMBHSTCNT); /* Reset SMBBLKDAT */ + for (i = 1; i <= data->block[0]; i++) { + data->block[i] = inb_p(SMBBLKDAT); +#ifdef DEBUG + printk + ("i2c-ali15x3.o: Blk: len=%d, i=%d, data=%02x\n", + len, i, data->block[i]); +#endif /* DEBUG */ + } + break; + } + return 0; +} + + +u32 ali15x3_func(struct i2c_adapter *adapter) +{ + return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_BLOCK_DATA; +} + +static struct i2c_algorithm smbus_algorithm = { + .name = "Non-I2C SMBus adapter", + .id = I2C_ALGO_SMBUS, + .smbus_xfer = ali15x3_access, + .functionality = ali15x3_func, +}; + +static struct i2c_adapter ali15x3_adapter = { + .owner = THIS_MODULE, + .name = "unset", + .id = I2C_ALGO_SMBUS | I2C_HW_SMBUS_ALI15X3, + .algo = &smbus_algorithm, +}; + + + +static struct pci_device_id ali15x3_ids[] __devinitdata = { + { 0, } +}; + +static int __devinit ali15x3_probe(struct pci_dev *dev, const struct pci_device_id *id) +{ + if (ali15x3_setup()) { + printk + ("i2c-ali15x3.o: ALI15X3 not detected, module not inserted.\n"); + + return -ENODEV; + } + + sprintf(ali15x3_adapter.name, "SMBus ALI15X3 adapter at %04x", + ali15x3_smba); + i2c_add_adapter(&ali15x3_adapter); +} + +static void __devexit ali15x3_remove(struct pci_dev *dev) +{ + i2c_del_adapter(&ali15x3_adapter); +} + +static struct pci_driver ali15x3_driver = { + .name = "ali15x3 smbus", + .id_table = ali15x3_ids, + .probe = ali15x3_probe, + .remove = __devexit_p(ali15x3_remove), +}; + +static int __init i2c_ali15x3_init(void) +{ + printk("i2c-ali15x3.o version %s (%s)\n", I2C_VERSION, I2C_DATE); + return pci_module_init(&ali15x3_driver); +} + + +static void __exit i2c_ali15x3_exit(void) +{ + pci_unregister_driver(&ali15x3_driver); + release_region(ali15x3_smba, ALI15X3_SMB_IOSIZE); +} + + + +MODULE_AUTHOR + ("Frodo Looijaard , Philip Edelbrock , and Mark D. Studebaker "); +MODULE_DESCRIPTION("ALI15X3 SMBus driver"); +MODULE_LICENSE("GPL"); + +module_init(i2c_ali15x3_init); +module_exit(i2c_ali15x3_exit);