From: Vojtech Pavlik <vojtech@suse.cz>

Add UDMA6 support to ALi IDE driver.  Forward port from 2.4 and a patch
from ALi.



---

 drivers/ide/pci/alim15x3.c |   17 ++++++++++++-----
 1 files changed, 12 insertions(+), 5 deletions(-)

diff -puN drivers/ide/pci/alim15x3.c~ide-ali-UDMA6-support drivers/ide/pci/alim15x3.c
--- 25/drivers/ide/pci/alim15x3.c~ide-ali-UDMA6-support	2004-01-24 09:45:38.000000000 -0800
+++ 25-akpm/drivers/ide/pci/alim15x3.c	2004-01-24 09:45:38.000000000 -0800
@@ -1,5 +1,5 @@
 /*
- * linux/drivers/ide/pci/alim15x3.c		Version 0.16	2003/01/02
+ * linux/drivers/ide/pci/alim15x3.c		Version 0.17	2003/01/02
  *
  *  Copyright (C) 1998-2000 Michel Aubry, Maintainer
  *  Copyright (C) 1998-2000 Andrzej Krzysztofowicz, Maintainer
@@ -19,6 +19,7 @@
  *	Don't use LBA48 mode on ALi <= 0xC4
  *	Don't poke 0x79 with a non ALi northbridge
  *	Don't flip undefined bits on newer chipsets (fix Fujitsu laptop hang)
+ *	Allow UDMA6 on revisions > 0xC4
  *
  *  Documentation
  *	Chipset documentation available under NDA only
@@ -406,7 +407,9 @@ static u8 ali15x3_ratemask (ide_drive_t 
 {
 	u8 mode = 0, can_ultra	= ali15x3_can_ultra(drive);
 
-	if (m5229_revision >= 0xC4 && can_ultra) {
+	if (m5229_revision > 0xC4 && can_ultra) {
+		mode = 4;
+	} else if (m5229_revision == 0xC4 && can_ultra) {
 		mode = 3;
 	} else if (m5229_revision >= 0xC2 && can_ultra) {
 		mode = 2;
@@ -439,11 +442,15 @@ static int ali15x3_tune_chipset (ide_dri
 {
 	ide_hwif_t *hwif	= HWIF(drive);
 	struct pci_dev *dev	= hwif->pci_dev;
-	u8 speed	= ide_rate_filter(ali15x3_ratemask(drive), xferspeed);
+	u8 speed		= ide_rate_filter(ali15x3_ratemask(drive), xferspeed);
+	u8 speed1		= speed;
 	u8 unit			= (drive->select.b.unit & 0x01);
 	u8 tmpbyte		= 0x00;
 	int m5229_udma		= (hwif->channel) ? 0x57 : 0x56;
 
+        if (speed == XFER_UDMA_6)
+                speed1 = 0x47;
+
 	if (speed < XFER_UDMA_0) {
 		u8 ultra_enable	= (unit) ? 0x7f : 0xf7;
 		/*
@@ -461,7 +468,7 @@ static int ali15x3_tune_chipset (ide_dri
 		/*
 		 * enable ultra dma and set timing
 		 */
-		tmpbyte |= ((0x08 | ((4-speed)&0x07)) << (unit << 2));
+		tmpbyte |= ((0x08 | ((4-speed1)&0x07)) << (unit << 2));
 		pci_write_config_byte(dev, m5229_udma, tmpbyte);
 		if (speed >= XFER_UDMA_3) {
 			pci_read_config_byte(dev, 0x4b, &tmpbyte);
@@ -757,7 +764,7 @@ static void __init init_hwif_common_ali1
 	hwif->atapi_dma = 1;
 
 	if (m5229_revision > 0x20)
-		hwif->ultra_mask = 0x3f;
+		hwif->ultra_mask = 0x7f;
 	hwif->mwdma_mask = 0x07;
 	hwif->swdma_mask = 0x07;
 

_