From: James Nelson Updates to cciss documentation. mkdev.cciss is no longer needed, since it is handled by the MAKEDEV program. Signed-off-by: James Nelson Signed-off-by: Andrew Morton --- /dev/null | 40 ---------------------------------------- 25-akpm/Documentation/00-INDEX | 2 -- 25-akpm/Documentation/cciss.txt | 27 +++++++++++++-------------- 3 files changed, 13 insertions(+), 56 deletions(-) diff -puN Documentation/00-INDEX~cciss-documentation-update Documentation/00-INDEX --- 25/Documentation/00-INDEX~cciss-documentation-update 2004-12-27 01:21:38.092748872 -0800 +++ 25-akpm/Documentation/00-INDEX 2004-12-27 01:21:38.099747808 -0800 @@ -172,8 +172,6 @@ memory.txt - info on typical Linux memory problems. mips/ - directory with info about Linux on MIPS architecture. -mkdev.cciss - - script to make /dev entries for SMART controllers (see cciss.txt). mono.txt - how to execute Mono-based .NET binaries with the help of BINFMT_MISC. moxa-smartio diff -puN Documentation/cciss.txt~cciss-documentation-update Documentation/cciss.txt --- 25/Documentation/cciss.txt~cciss-documentation-update 2004-12-27 01:21:38.094748568 -0800 +++ 25-akpm/Documentation/cciss.txt 2004-12-27 01:21:38.100747656 -0800 @@ -17,25 +17,27 @@ This driver is known to work with the fo * SA 6422 * SA V100 -If nodes are not already created in the /dev/cciss directory +If nodes are not already created in the /dev/cciss directory, run as root: -# mkdev.cciss [ctlrs] - -Where ctlrs is the number of controllers you have (defaults to 1 if not -specified). +# cd /dev +# ./MAKEDEV cciss Device Naming: -------------- -You need some entries in /dev for the cciss device. The mkdev.cciss script +You need some entries in /dev for the cciss device. The MAKEDEV script can make device nodes for you automatically. Currently the device setup is as follows: Major numbers: 104 cciss0 105 cciss1 - 106 cciss2 - etc... + 106 cciss2 + 105 cciss3 + 108 cciss4 + 109 cciss5 + 110 cciss6 + 111 cciss7 Minor numbers: b7 b6 b5 b4 b3 b2 b1 b0 @@ -45,7 +47,7 @@ Minor numbers: | +-------------------- Logical Volume number -The suggested device naming scheme is: +The device naming scheme is: /dev/cciss/c0d0 Controller 0, disk 0, whole device /dev/cciss/c0d0p1 Controller 0, disk 0, partition 1 /dev/cciss/c0d0p2 Controller 0, disk 0, partition 2 @@ -117,16 +119,13 @@ from the adapter, informing the SCSI mid Note that the naming convention of the /proc filesystem entries contains a number in addition to the driver name. (E.g. "cciss0" -instead of just "cciss" which you might expect.) This is because -of changes to the 2.4 kernel PCI interface related to PCI hot plug -that imply the driver must register with the SCSI mid layer once per -adapter instance rather than once per driver. +instead of just "cciss" which you might expect.) Note: ONLY sequential access devices and medium changers are presented as SCSI devices to the SCSI mid layer by the cciss driver. Specifically, physical SCSI disk drives are NOT presented to the SCSI mid layer. The physical SCSI disk drives are controlled directly by the array controller -hardware and it is important to prevent the OS from attempting to directly +hardware and it is important to prevent the kernel from attempting to directly access these devices too, as if the array controller were merely a SCSI controller in the same way that we are allowing it to access SCSI tape drives. diff -L Documentation/mkdev.cciss -puN Documentation/mkdev.cciss~cciss-documentation-update /dev/null --- 25/Documentation/mkdev.cciss +++ /dev/null 2003-09-15 06:40:47.000000000 -0700 @@ -1,40 +0,0 @@ -#!/bin/sh -# Script to create device nodes for SMART array controllers -# Usage: -# mkdev.cciss [num controllers] [num log volumes] [num partitions] -# -# With no arguments, the script assumes 1 controller, 16 logical volumes, -# and 16 partitions/volume, which is adequate for most configurations. -# -# If you had 5 controllers and were planning on no more than 4 logical volumes -# each, using a maximum of 8 partitions per volume, you could say: -# -# mkdev.cciss 5 4 8 -# -# Of course, this has no real benefit over "mkdev.cciss 5" except that it -# doesn't create so many device nodes in /dev/cciss. - -NR_CTLR=${1-1} -NR_VOL=${2-16} -NR_PART=${3-16} - -if [ ! -d /dev/cciss ]; then - mkdir -p /dev/cciss -fi - -C=0; while [ $C -lt $NR_CTLR ]; do - MAJ=`expr $C + 104` - D=0; while [ $D -lt $NR_VOL ]; do - P=0; while [ $P -lt $NR_PART ]; do - MIN=`expr $D \* 16 + $P` - if [ $P -eq 0 ]; then - mknod /dev/cciss/c${C}d${D} b $MAJ $MIN - else - mknod /dev/cciss/c${C}d${D}p${P} b $MAJ $MIN - fi - P=`expr $P + 1` - done - D=`expr $D + 1` - done - C=`expr $C + 1` -done _