Chapter 6. libata SCSI translation/emulation

Table of Contents

ata_std_bios_param — generic bios head/sector/cylinder calculator used by sd.

ata_scsi_unlock_native_capacity — unlock native capacity

ata_scsi_slave_config — Set SCSI device attributes

ata_scsi_slave_destroy — SCSI device is about to be destroyed

__ata_change_queue_depth — helper for ata_scsi_change_queue_depth

ata_scsi_change_queue_depth — SCSI callback for queue depth config

ata_scsi_queuecmd — Issue SCSI cdb to libata-managed device

ata_scsi_simulate — simulate SCSI command on ATA device

ata_sas_port_alloc — Allocate port for a SAS attached SATA device

ata_sas_port_start — Set port up for dma.

ata_sas_port_stop Undo ata_sas_port_start

ata_sas_async_probe — simply schedule probing and return

ata_sas_port_init — Initialize a SATA device

ata_sas_port_destroy — Destroy a SATA port allocated by ata_sas_port_alloc

ata_sas_slave_configure — Default slave_config routine for libata devices

ata_sas_queuecmd — Issue SCSI cdb to libata-managed device

ata_get_identity — Handler for HDIO_GET_IDENTITY ioctl

ata_cmd_ioctl — Handler for HDIO_DRIVE_CMD ioctl

ata_task_ioctl — Handler for HDIO_DRIVE_TASK ioctl

ata_scsi_qc_new — acquire new ata_queued_cmd reference

ata_dump_status — user friendly display of error info

ata_to_sense_error — convert ATA error to SCSI error

ata_gen_ata_sense — generate a SCSI fixed sense block

atapi_drain_needed — Check whether data transfer may overflow

ata_scsi_start_stop_xlat — Translate SCSI START STOP UNIT command

ata_scsi_flush_xlat — Translate SCSI SYNCHRONIZE CACHE command

scsi_6_lba_len — Get LBA and transfer length

scsi_10_lba_len — Get LBA and transfer length

scsi_16_lba_len — Get LBA and transfer length

ata_scsi_verify_xlat — Translate SCSI VERIFY command into an ATA one

ata_scsi_rw_xlat — Translate SCSI r/w command into an ATA one

ata_scsi_translate — Translate then issue SCSI command to ATA device

ata_scsi_rbuf_get — Map response buffer.

ata_scsi_rbuf_put — Unmap response buffer.

ata_scsi_rbuf_fill — wrapper for SCSI command simulators

ata_scsiop_inq_std — Simulate INQUIRY command

ata_scsiop_inq_00 — Simulate INQUIRY VPD page 0, list of pages

ata_scsiop_inq_80 — Simulate INQUIRY VPD page 80, device serial number

ata_scsiop_inq_83 — Simulate INQUIRY VPD page 83, device identity

ata_scsiop_inq_89 — Simulate INQUIRY VPD page 89, ATA info

modecpy — Prepare response for MODE SENSE

ata_msense_caching — Simulate MODE SENSE caching info page

ata_msense_control — Simulate MODE SENSE control mode page

ata_msense_rw_recovery — Simulate MODE SENSE r/w error recovery page

ata_scsiop_mode_sense — Simulate MODE SENSE 6, 10 commands

ata_scsiop_read_cap — Simulate READ CAPACITY[ 16] commands

ata_scsiop_report_luns — Simulate REPORT LUNS command

atapi_xlat — Initialize PACKET taskfile

ata_scsi_find_dev — lookup ata_device from scsi_cmnd

ata_scsi_pass_thru — convert ATA pass-thru CDB to taskfile

ata_format_dsm_trim_descr — SATL Write Same to DSM Trim

ata_scsi_write_same_xlat — SATL Write Same to ATA SCT Write Same

ata_scsiop_maint_in — Simulate a subset of MAINTENANCE_IN

ata_scsi_report_zones_complete — convert ATA output

ata_mselect_caching — Simulate MODE SELECT for caching info page

ata_mselect_control — Simulate MODE SELECT for control page

ata_scsi_mode_select_xlat — Simulate MODE SELECT 6, 10 commands

ata_get_xlat_func — check if SCSI to ATA translation is possible

ata_scsi_dump_cdb — dump SCSI command contents to dmesg

ata_scsi_offline_dev — offline attached SCSI device

ata_scsi_remove_dev — remove attached SCSI device

ata_scsi_media_change_notify — send media change event

ata_scsi_hotplug — SCSI part of hotplug

ata_scsi_user_scan — indication for user-initiated bus scan

ata_scsi_dev_rescan — initiate scsi_rescan_device