Ethernet Bridging¶
Introduction¶
The IEEE 802.1Q-2022 (Bridges and Bridged Networks) standard defines the operation of bridges in computer networks. A bridge, in the context of this standard, is a device that connects two or more network segments and operates at the data link layer (Layer 2) of the OSI (Open Systems Interconnection) model. The purpose of a bridge is to filter and forward frames between different segments based on the destination MAC (Media Access Control) address.
Bridge kAPI¶
Here are some core structures of bridge code. Note that the kAPI is unstable, and can be changed at any time.
-
struct net_bridge_vlan¶
per-vlan entry
Definition:
struct net_bridge_vlan {
struct rhash_head vnode;
struct rhash_head tnode;
u16 vid;
u16 flags;
u16 priv_flags;
u8 state;
struct pcpu_sw_netstats __percpu *stats;
union {
struct net_bridge *br;
struct net_bridge_port *port;
};
union {
refcount_t refcnt;
struct net_bridge_vlan *brvlan;
};
struct br_tunnel_info tinfo;
union {
struct net_bridge_mcast br_mcast_ctx;
struct net_bridge_mcast_port port_mcast_ctx;
};
u16 msti;
struct list_head vlist;
struct rcu_head rcu;
};
Members
vnode
rhashtable member
tnode
rhashtable member
vid
VLAN id
flags
bridge vlan flags
priv_flags
private (in-kernel) bridge vlan flags
state
STP state (e.g. blocking, learning, forwarding)
stats
per-cpu VLAN statistics
{unnamed_union}
anonymous
br
if MASTER flag set, this points to a bridge struct
port
if MASTER flag unset, this points to a port struct
{unnamed_union}
anonymous
refcnt
if MASTER flag set, this is bumped for each port referencing it
brvlan
if MASTER flag unset, this points to the global per-VLAN context for this VLAN entry
tinfo
bridge tunnel info
{unnamed_union}
anonymous
br_mcast_ctx
if MASTER flag set, this is the global vlan multicast context
port_mcast_ctx
if MASTER flag unset, this is the per-port/vlan multicast context
msti
if MASTER flag set, this holds the VLANs MST instance
vlist
sorted list of VLAN entries
rcu
used for entry destruction
Description
This structure is shared between the global per-VLAN entries contained in the bridge rhashtable and the local per-port per-VLAN entries contained in the port's rhashtable. The union entries should be interpreted depending on the entry flags that are set.
Bridge uAPI¶
Modern Linux bridge uAPI is accessed via Netlink interface. You can find below files where the bridge and bridge port netlink attributes are defined.
Bridge netlink attributes¶
Please note that the timer values in the following section are expected in clock_t format, which is seconds multiplied by USER_HZ (generally defined as 100).
- IFLA_BR_FORWARD_DELAY
The bridge forwarding delay is the time spent in LISTENING state (before moving to LEARNING) and in LEARNING state (before moving to FORWARDING). Only relevant if STP is enabled.
The valid values are between (2 * USER_HZ) and (30 * USER_HZ). The default value is (15 * USER_HZ).
- IFLA_BR_HELLO_TIME
The time between hello packets sent by the bridge, when it is a root bridge or a designated bridge. Only relevant if STP is enabled.
The valid values are between (1 * USER_HZ) and (10 * USER_HZ). The default value is (2 * USER_HZ).
- IFLA_BR_MAX_AGE
The hello packet timeout is the time until another bridge in the spanning tree is assumed to be dead, after reception of its last hello message. Only relevant if STP is enabled.
The valid values are between (6 * USER_HZ) and (40 * USER_HZ). The default value is (20 * USER_HZ).
- IFLA_BR_AGEING_TIME
Configure the bridge's FDB entries aging time. It is the time a MAC address will be kept in the FDB after a packet has been received from that address. After this time has passed, entries are cleaned up. Allow values outside the 802.1 standard specification for special cases:
0 - entry never ages (all permanent)
1 - entry disappears (no persistence)
The default value is (300 * USER_HZ).
- IFLA_BR_STP_STATE
Turn spanning tree protocol on (IFLA_BR_STP_STATE > 0) or off (IFLA_BR_STP_STATE == 0) for this bridge.
The default value is 0 (disabled).
- IFLA_BR_PRIORITY
Set this bridge's spanning tree priority, used during STP root bridge election.
The valid values are between 0 and 65535.
- IFLA_BR_VLAN_FILTERING
Turn VLAN filtering on (IFLA_BR_VLAN_FILTERING > 0) or off (IFLA_BR_VLAN_FILTERING == 0). When disabled, the bridge will not consider the VLAN tag when handling packets.
The default value is 0 (disabled).
- IFLA_BR_VLAN_PROTOCOL
Set the protocol used for VLAN filtering.
The valid values are 0x8100(802.1Q) or 0x88A8(802.1AD). The default value is 0x8100(802.1Q).
- IFLA_BR_GROUP_FWD_MASK
The group forwarding mask. This is the bitmask that is applied to decide whether to forward incoming frames destined to link-local addresses (of the form 01:80:C2:00:00:0X).
The default value is 0, which means the bridge does not forward any link-local frames coming on this port.
- IFLA_BR_ROOT_ID
The bridge root id, read only.
- IFLA_BR_BRIDGE_ID
The bridge id, read only.
- IFLA_BR_ROOT_PORT
The bridge root port, read only.
- IFLA_BR_ROOT_PATH_COST
The bridge root path cost, read only.
- IFLA_BR_TOPOLOGY_CHANGE
The bridge topology change, read only.
- IFLA_BR_TOPOLOGY_CHANGE_DETECTED
The bridge topology change detected, read only.
- IFLA_BR_HELLO_TIMER
The bridge hello timer, read only.
- IFLA_BR_TCN_TIMER
The bridge tcn timer, read only.
- IFLA_BR_TOPOLOGY_CHANGE_TIMER
The bridge topology change timer, read only.
- IFLA_BR_GC_TIMER
The bridge gc timer, read only.
- IFLA_BR_GROUP_ADDR
Set the MAC address of the multicast group this bridge uses for STP. The address must be a link-local address in standard Ethernet MAC address format. It is an address of the form 01:80:C2:00:00:0X, with X in [0, 4..f].
The default value is 0.
- IFLA_BR_FDB_FLUSH
Flush bridge's fdb dynamic entries.
- IFLA_BR_MCAST_ROUTER
Set bridge's multicast router if IGMP snooping is enabled. The valid values are:
0 - disabled.
1 - automatic (queried).
2 - permanently enabled.
The default value is 1.
- IFLA_BR_MCAST_SNOOPING
Turn multicast snooping on (IFLA_BR_MCAST_SNOOPING > 0) or off (IFLA_BR_MCAST_SNOOPING == 0).
The default value is 1.
- IFLA_BR_MCAST_QUERY_USE_IFADDR
If enabled use the bridge's own IP address as source address for IGMP queries (IFLA_BR_MCAST_QUERY_USE_IFADDR > 0) or the default of 0.0.0.0 (IFLA_BR_MCAST_QUERY_USE_IFADDR == 0).
The default value is 0 (disabled).
- IFLA_BR_MCAST_QUERIER
Enable (IFLA_BR_MULTICAST_QUERIER > 0) or disable (IFLA_BR_MULTICAST_QUERIER == 0) IGMP querier, ie sending of multicast queries by the bridge.
The default value is 0 (disabled).
- IFLA_BR_MCAST_HASH_ELASTICITY
Set multicast database hash elasticity, It is the maximum chain length in the multicast hash table. This attribute is deprecated and the value is always 16.
- IFLA_BR_MCAST_HASH_MAX
Set maximum size of the multicast hash table
The default value is 4096, the value must be a power of 2.
- IFLA_BR_MCAST_LAST_MEMBER_CNT
The Last Member Query Count is the number of Group-Specific Queries sent before the router assumes there are no local members. The Last Member Query Count is also the number of Group-and-Source-Specific Queries sent before the router assumes there are no listeners for a particular source.
The default value is 2.
- IFLA_BR_MCAST_STARTUP_QUERY_CNT
The Startup Query Count is the number of Queries sent out on startup, separated by the Startup Query Interval.
The default value is 2.
- IFLA_BR_MCAST_LAST_MEMBER_INTVL
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
The default value is (1 * USER_HZ).
- IFLA_BR_MCAST_MEMBERSHIP_INTVL
The interval after which the bridge will leave a group, if no membership reports for this group are received.
The default value is (260 * USER_HZ).
- IFLA_BR_MCAST_QUERIER_INTVL
The interval between queries sent by other routers. if no queries are seen after this delay has passed, the bridge will start to send its own queries (as if IFLA_BR_MCAST_QUERIER_INTVL was enabled).
The default value is (255 * USER_HZ).
- IFLA_BR_MCAST_QUERY_INTVL
The Query Interval is the interval between General Queries sent by the Querier.
The default value is (125 * USER_HZ). The minimum value is (1 * USER_HZ).
- IFLA_BR_MCAST_QUERY_RESPONSE_INTVL
The Max Response Time used to calculate the Max Resp Code inserted into the periodic General Queries.
The default value is (10 * USER_HZ).
- IFLA_BR_MCAST_STARTUP_QUERY_INTVL
The interval between queries in the startup phase.
The default value is (125 * USER_HZ) / 4. The minimum value is (1 * USER_HZ).
- IFLA_BR_NF_CALL_IPTABLES
Enable (NF_CALL_IPTABLES > 0) or disable (NF_CALL_IPTABLES == 0) iptables hooks on the bridge.
The default value is 0 (disabled).
- IFLA_BR_NF_CALL_IP6TABLES
Enable (NF_CALL_IP6TABLES > 0) or disable (NF_CALL_IP6TABLES == 0) ip6tables hooks on the bridge.
The default value is 0 (disabled).
- IFLA_BR_NF_CALL_ARPTABLES
Enable (NF_CALL_ARPTABLES > 0) or disable (NF_CALL_ARPTABLES == 0) arptables hooks on the bridge.
The default value is 0 (disabled).
- IFLA_BR_VLAN_DEFAULT_PVID
VLAN ID applied to untagged and priority-tagged incoming packets.
The default value is 1. Setting to the special value 0 makes all ports of this bridge not have a PVID by default, which means that they will not accept VLAN-untagged traffic.
- IFLA_BR_PAD
Bridge attribute padding type for netlink message.
- IFLA_BR_VLAN_STATS_ENABLED
Enable (IFLA_BR_VLAN_STATS_ENABLED == 1) or disable (IFLA_BR_VLAN_STATS_ENABLED == 0) per-VLAN stats accounting.
The default value is 0 (disabled).
- IFLA_BR_MCAST_STATS_ENABLED
Enable (IFLA_BR_MCAST_STATS_ENABLED > 0) or disable (IFLA_BR_MCAST_STATS_ENABLED == 0) multicast (IGMP/MLD) stats accounting.
The default value is 0 (disabled).
- IFLA_BR_MCAST_IGMP_VERSION
Set the IGMP version.
The valid values are 2 and 3. The default value is 2.
- IFLA_BR_MCAST_MLD_VERSION
Set the MLD version.
The valid values are 1 and 2. The default value is 1.
- IFLA_BR_VLAN_STATS_PER_PORT
Enable (IFLA_BR_VLAN_STATS_PER_PORT == 1) or disable (IFLA_BR_VLAN_STATS_PER_PORT == 0) per-VLAN per-port stats accounting. Can be changed only when there are no port VLANs configured.
The default value is 0 (disabled).
- IFLA_BR_MULTI_BOOLOPT
The multi_boolopt is used to control new boolean options to avoid adding new netlink attributes. You can look at
enum br_boolopt_id
for those options.- IFLA_BR_MCAST_QUERIER_STATE
Bridge mcast querier states, read only.
- IFLA_BR_FDB_N_LEARNED
The number of dynamically learned FDB entries for the current bridge, read only.
- IFLA_BR_FDB_MAX_LEARNED
Set the number of max dynamically learned FDB entries for the current bridge.
Bridge port netlink attributes¶
- IFLA_BRPORT_STATE
The operation state of the port. Here are the valid values.
0 - port is in STP DISABLED state. Make this port completely inactive for STP. This is also called BPDU filter and could be used to disable STP on an untrusted port, like a leaf virtual device. The traffic forwarding is also stopped on this port.
1 - port is in STP LISTENING state. Only valid if STP is enabled on the bridge. In this state the port listens for STP BPDUs and drops all other traffic frames.
2 - port is in STP LEARNING state. Only valid if STP is enabled on the bridge. In this state the port will accept traffic only for the purpose of updating MAC address tables.
3 - port is in STP FORWARDING state. Port is fully active.
4 - port is in STP BLOCKING state. Only valid if STP is enabled on the bridge. This state is used during the STP election process. In this state, port will only process STP BPDUs.
- IFLA_BRPORT_PRIORITY
The STP port priority. The valid values are between 0 and 255.
- IFLA_BRPORT_COST
The STP path cost of the port. The valid values are between 1 and 65535.
- IFLA_BRPORT_MODE
Set the bridge port mode. See BRIDGE_MODE_HAIRPIN for more details.
- IFLA_BRPORT_GUARD
Controls whether STP BPDUs will be processed by the bridge port. By default, the flag is turned off to allow BPDU processing. Turning this flag on will disable the bridge port if a STP BPDU packet is received.
If the bridge has Spanning Tree enabled, hostile devices on the network may send BPDU on a port and cause network failure. Setting guard on will detect and stop this by disabling the port. The port will be restarted if the link is brought down, or removed and reattached.
- IFLA_BRPORT_PROTECT
Controls whether a given port is allowed to become a root port or not. Only used when STP is enabled on the bridge. By default the flag is off.
This feature is also called root port guard. If BPDU is received from a leaf (edge) port, it should not be elected as root port. This could be used if using STP on a bridge and the downstream bridges are not fully trusted; this prevents a hostile guest from rerouting traffic.
- IFLA_BRPORT_FAST_LEAVE
This flag allows the bridge to immediately stop multicast traffic forwarding on a port that receives an IGMP Leave message. It is only used when IGMP snooping is enabled on the bridge. By default the flag is off.
- IFLA_BRPORT_LEARNING
Controls whether a given port will learn source MAC addresses from received traffic or not. Also controls whether dynamic FDB entries (which can also be added by software) will be refreshed by incoming traffic. By default this flag is on.
- IFLA_BRPORT_UNICAST_FLOOD
Controls whether unicast traffic for which there is no FDB entry will be flooded towards this port. By default this flag is on.
- IFLA_BRPORT_PROXYARP
Enable proxy ARP on this port.
- IFLA_BRPORT_LEARNING_SYNC
Controls whether a given port will sync MAC addresses learned on device port to bridge FDB.
- IFLA_BRPORT_PROXYARP_WIFI
Enable proxy ARP on this port which meets extended requirements by IEEE 802.11 and Hotspot 2.0 specifications.
IFLA_BRPORT_ROOT_ID
IFLA_BRPORT_BRIDGE_ID
IFLA_BRPORT_DESIGNATED_PORT
IFLA_BRPORT_DESIGNATED_COST
IFLA_BRPORT_ID
IFLA_BRPORT_NO
IFLA_BRPORT_TOPOLOGY_CHANGE_ACK
IFLA_BRPORT_CONFIG_PENDING
IFLA_BRPORT_MESSAGE_AGE_TIMER
IFLA_BRPORT_FORWARD_DELAY_TIMER
IFLA_BRPORT_HOLD_TIMER
- IFLA_BRPORT_FLUSH
Flush bridge ports' fdb dynamic entries.
- IFLA_BRPORT_MULTICAST_ROUTER
Configure the port's multicast router presence. A port with a multicast router will receive all multicast traffic. The valid values are:
0 disable multicast routers on this port
1 let the system detect the presence of routers (default)
2 permanently enable multicast traffic forwarding on this port
- 3 enable multicast routers temporarily on this port, not depending
on incoming queries.
IFLA_BRPORT_PAD
- IFLA_BRPORT_MCAST_FLOOD
Controls whether a given port will flood multicast traffic for which there is no MDB entry. By default this flag is on.
- IFLA_BRPORT_MCAST_TO_UCAST
Controls whether a given port will replicate packets using unicast instead of multicast. By default this flag is off.
This is done by copying the packet per host and changing the multicast destination MAC to a unicast one accordingly.
mcast_to_unicast works on top of the multicast snooping feature of the bridge. Which means unicast copies are only delivered to hosts which are interested in unicast and signaled this via IGMP/MLD reports previously.
This feature is intended for interface types which have a more reliable and/or efficient way to deliver unicast packets than broadcast ones (e.g. WiFi).
However, it should only be enabled on interfaces where no IGMPv2/MLDv1 report suppression takes place. IGMP/MLD report suppression issue is usually overcome by the network daemon (supplicant) enabling AP isolation and by that separating all STAs.
Delivery of STA-to-STA IP multicast is made possible again by enabling and utilizing the bridge hairpin mode, which considers the incoming port as a potential outgoing port, too (see BRIDGE_MODE_HAIRPIN option). Hairpin mode is performed after multicast snooping, therefore leading to only deliver reports to STAs running a multicast router.
- IFLA_BRPORT_VLAN_TUNNEL
Controls whether vlan to tunnel mapping is enabled on the port. By default this flag is off.
- IFLA_BRPORT_BCAST_FLOOD
Controls flooding of broadcast traffic on the given port. By default this flag is on.
- IFLA_BRPORT_GROUP_FWD_MASK
Set the group forward mask. This is a bitmask that is applied to decide whether to forward incoming frames destined to link-local addresses. The addresses of the form are 01:80:C2:00:00:0X (defaults to 0, which means the bridge does not forward any link-local frames coming on this port).
- IFLA_BRPORT_NEIGH_SUPPRESS
Controls whether neighbor discovery (arp and nd) proxy and suppression is enabled on the port. By default this flag is off.
- IFLA_BRPORT_ISOLATED
Controls whether a given port will be isolated, which means it will be able to communicate with non-isolated ports only. By default this flag is off.
- IFLA_BRPORT_BACKUP_PORT
Set a backup port. If the port loses carrier all traffic will be redirected to the configured backup port. Set the value to 0 to disable it.
IFLA_BRPORT_MRP_RING_OPEN
IFLA_BRPORT_MRP_IN_OPEN
- IFLA_BRPORT_MCAST_EHT_HOSTS_LIMIT
The number of per-port EHT hosts limit. The default value is 512. Setting to 0 is not allowed.
- IFLA_BRPORT_MCAST_EHT_HOSTS_CNT
The current number of tracked hosts, read only.
- IFLA_BRPORT_LOCKED
Controls whether a port will be locked, meaning that hosts behind the port will not be able to communicate through the port unless an FDB entry with the unit's MAC address is in the FDB. The common use case is that hosts are allowed access through authentication with the IEEE 802.1X protocol or based on whitelists. By default this flag is off.
Please note that secure 802.1X deployments should always use the BR_BOOLOPT_NO_LL_LEARN flag, to not permit the bridge to populate its FDB based on link-local (EAPOL) traffic received on the port.
- IFLA_BRPORT_MAB
Controls whether a port will use MAC Authentication Bypass (MAB), a technique through which select MAC addresses may be allowed on a locked port, without using 802.1X authentication. Packets with an unknown source MAC address generates a "locked" FDB entry on the incoming bridge port. The common use case is for user space to react to these bridge FDB notifications and optionally replace the locked FDB entry with a normal one, allowing traffic to pass for whitelisted MAC addresses.
Setting this flag also requires IFLA_BRPORT_LOCKED and IFLA_BRPORT_LEARNING. IFLA_BRPORT_LOCKED ensures that unauthorized data packets are dropped, and IFLA_BRPORT_LEARNING allows the dynamic FDB entries installed by user space (as replacements for the locked FDB entries) to be refreshed and/or aged out.
IFLA_BRPORT_MCAST_N_GROUPS
- IFLA_BRPORT_MCAST_MAX_GROUPS
Sets the maximum number of MDB entries that can be registered for a given port. Attempts to register more MDB entries at the port than this limit allows will be rejected, whether they are done through netlink (e.g. the bridge tool), or IGMP or MLD membership reports. Setting a limit of 0 disables the limit. The default value is 0.
- IFLA_BRPORT_NEIGH_VLAN_SUPPRESS
Controls whether neighbor discovery (arp and nd) proxy and suppression is enabled for a given port. By default this flag is off.
Note that this option only takes effect when IFLA_BRPORT_NEIGH_SUPPRESS is enabled for a given port.
- IFLA_BRPORT_BACKUP_NHID
The FDB nexthop object ID to attach to packets being redirected to a backup port that has VLAN tunnel mapping enabled (via the IFLA_BRPORT_VLAN_TUNNEL option). Setting a value of 0 (default) has the effect of not attaching any ID.
Bridge sysfs¶
The sysfs interface is deprecated and should not be extended if new options are added.
STP¶
The STP (Spanning Tree Protocol) implementation in the Linux bridge driver is a critical feature that helps prevent loops and broadcast storms in Ethernet networks by identifying and disabling redundant links. In a Linux bridge context, STP is crucial for network stability and availability.
STP is a Layer 2 protocol that operates at the Data Link Layer of the OSI model. It was originally developed as IEEE 802.1D and has since evolved into multiple versions, including Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol (MSTP).
The 802.1D-2004 removed the original Spanning Tree Protocol, instead incorporating the Rapid Spanning Tree Protocol (RSTP). By 2014, all the functionality defined by IEEE 802.1D has been incorporated into either IEEE 802.1Q (Bridges and Bridged Networks) or IEEE 802.1AC (MAC Service Definition). 802.1D has been officially withdrawn in 2022.
Bridge Ports and STP States¶
- In the context of STP, bridge ports can be in one of the following states:
Blocking: The port is disabled for data traffic and only listens for BPDUs (Bridge Protocol Data Units) from other devices to determine the network topology.
Listening: The port begins to participate in the STP process and listens for BPDUs.
Learning: The port continues to listen for BPDUs and begins to learn MAC addresses from incoming frames but does not forward data frames.
Forwarding: The port is fully operational and forwards both BPDUs and data frames.
Disabled: The port is administratively disabled and does not participate in the STP process. The data frames forwarding are also disabled.
Root Bridge and Convergence¶
In the context of networking and Ethernet bridging in Linux, the root bridge is a designated switch in a bridged network that serves as a reference point for the spanning tree algorithm to create a loop-free topology.
- Here's how the STP works and root bridge is chosen:
Bridge Priority: Each bridge running a spanning tree protocol, has a configurable Bridge Priority value. The lower the value, the higher the priority. By default, the Bridge Priority is set to a standard value (e.g., 32768).
Bridge ID: The Bridge ID is composed of two components: Bridge Priority and the MAC address of the bridge. It uniquely identifies each bridge in the network. The Bridge ID is used to compare the priorities of different bridges.
Bridge Election: When the network starts, all bridges initially assume that they are the root bridge. They start advertising Bridge Protocol Data Units (BPDU) to their neighbors, containing their Bridge ID and other information.
BPDU Comparison: Bridges exchange BPDUs to determine the root bridge. Each bridge examines the received BPDUs, including the Bridge Priority and Bridge ID, to determine if it should adjust its own priorities. The bridge with the lowest Bridge ID will become the root bridge.
Root Bridge Announcement: Once the root bridge is determined, it sends BPDUs with information about the root bridge to all other bridges in the network. This information is used by other bridges to calculate the shortest path to the root bridge and, in doing so, create a loop-free topology.
Forwarding Ports: After the root bridge is selected and the spanning tree topology is established, each bridge determines which of its ports should be in the forwarding state (used for data traffic) and which should be in the blocking state (used to prevent loops). The root bridge's ports are all in the forwarding state. while other bridges have some ports in the blocking state to avoid loops.
Root Ports: After the root bridge is selected and the spanning tree topology is established, each non-root bridge processes incoming BPDUs and determines which of its ports provides the shortest path to the root bridge based on the information in the received BPDUs. This port is designated as the root port. And it is in the Forwarding state, allowing it to actively forward network traffic.
Designated ports: A designated port is the port through which the non-root bridge will forward traffic towards the designated segment. Designated ports are placed in the Forwarding state. All other ports on the non-root bridge that are not designated for specific segments are placed in the Blocking state to prevent network loops.
STP ensures network convergence by calculating the shortest path and disabling redundant links. When network topology changes occur (e.g., a link failure), STP recalculates the network topology to restore connectivity while avoiding loops.
Proper configuration of STP parameters, such as the bridge priority, can influence network performance, path selection and which bridge becomes the Root Bridge.
User space STP helper¶
The user space STP helper bridge-stp is a program to control whether to use
user mode spanning tree. The /sbin/bridge-stp <bridge> <start|stop>
is
called by the kernel when STP is enabled/disabled on a bridge
(via brctl stp <bridge> <on|off>
or ip link set <bridge> type bridge
stp_state <0|1>
). The kernel enables user_stp mode if that command returns
0, or enables kernel_stp mode if that command returns any other value.
VLAN¶
A LAN (Local Area Network) is a network that covers a small geographic area, typically within a single building or a campus. LANs are used to connect computers, servers, printers, and other networked devices within a localized area. LANs can be wired (using Ethernet cables) or wireless (using Wi-Fi).
A VLAN (Virtual Local Area Network) is a logical segmentation of a physical network into multiple isolated broadcast domains. VLANs are used to divide a single physical LAN into multiple virtual LANs, allowing different groups of devices to communicate as if they were on separate physical networks.
Typically there are two VLAN implementations, IEEE 802.1Q and IEEE 802.1ad (also known as QinQ). IEEE 802.1Q is a standard for VLAN tagging in Ethernet networks. It allows network administrators to create logical VLANs on a physical network and tag Ethernet frames with VLAN information, which is called VLAN-tagged frames. IEEE 802.1ad, commonly known as QinQ or Double VLAN, is an extension of the IEEE 802.1Q standard. QinQ allows for the stacking of multiple VLAN tags within a single Ethernet frame. The Linux bridge supports both the IEEE 802.1Q and 802.1AD protocol for VLAN tagging.
VLAN filtering on a bridge is disabled by default. After enabling VLAN filtering on a bridge, it will start forwarding frames to appropriate destinations based on their destination MAC address and VLAN tag (both must match).
Multicast¶
The Linux bridge driver has multicast support allowing it to process Internet Group Management Protocol (IGMP) or Multicast Listener Discovery (MLD) messages, and to efficiently forward multicast data packets. The bridge driver supports IGMPv2/IGMPv3 and MLDv1/MLDv2.
Multicast snooping¶
Multicast snooping is a networking technology that allows network switches to intelligently manage multicast traffic within a local area network (LAN).
The switch maintains a multicast group table, which records the association between multicast group addresses and the ports where hosts have joined these groups. The group table is dynamically updated based on the IGMP/MLD messages received. With the multicast group information gathered through snooping, the switch optimizes the forwarding of multicast traffic. Instead of blindly broadcasting the multicast traffic to all ports, it sends the multicast traffic based on the destination MAC address only to ports which have subscribed the respective destination multicast group.
When created, the Linux bridge devices have multicast snooping enabled by default. It maintains a Multicast forwarding database (MDB) which keeps track of port and group relationships.
IGMPv3/MLDv2 EHT support¶
The Linux bridge supports IGMPv3/MLDv2 EHT (Explicit Host Tracking), which was added by 474ddb37fa3a ("net: bridge: multicast: add EHT allow/block handling")
The explicit host tracking enables the device to keep track of each individual host that is joined to a particular group or channel. The main benefit of the explicit host tracking in IGMP is to allow minimal leave latencies when a host leaves a multicast group or channel.
The length of time between a host wanting to leave and a device stopping traffic forwarding is called the IGMP leave latency. A device configured with IGMPv3 or MLDv2 and explicit tracking can immediately stop forwarding traffic if the last host to request to receive traffic from the device indicates that it no longer wants to receive traffic. The leave latency is thus bound only by the packet transmission latencies in the multiaccess network and the processing time in the device.
Other multicast features¶
The Linux bridge also supports per-VLAN multicast snooping, which is disabled by default but can be enabled. And Multicast Router Discovery, which help identify the location of multicast routers.
Switchdev¶
Linux Bridge Switchdev is a feature in the Linux kernel that extends the capabilities of the traditional Linux bridge to work more efficiently with hardware switches that support switchdev. With Linux Bridge Switchdev, certain networking functions like forwarding, filtering, and learning of Ethernet frames can be offloaded to a hardware switch. This offloading reduces the burden on the Linux kernel and CPU, leading to improved network performance and lower latency.
To use Linux Bridge Switchdev, you need hardware switches that support the switchdev interface. This means that the switch hardware needs to have the necessary drivers and functionality to work in conjunction with the Linux kernel.
Please see the Ethernet switch device driver model (switchdev) document for more details.
Netfilter¶
The bridge netfilter module is a legacy feature that allows to filter bridged packets with iptables and ip6tables. Its use is discouraged. Users should consider using nftables for packet filtering.
The older ebtables tool is more feature-limited compared to nftables, but just like nftables it doesn't need this module either to function.
The br_netfilter module intercepts packets entering the bridge, performs minimal sanity tests on ipv4 and ipv6 packets and then pretends that these packets are being routed, not bridged. br_netfilter then calls the ip and ipv6 netfilter hooks from the bridge layer, i.e. ip(6)tables rulesets will also see these packets.
br_netfilter is also the reason for the iptables physdev match: This match is the only way to reliably tell routed and bridged packets apart in an iptables ruleset.
Note that ebtables and nftables will work fine without the br_netfilter module. iptables/ip6tables/arptables do not work for bridged traffic because they plug in the routing stack. nftables rules in ip/ip6/inet/arp families won't see traffic that is forwarded by a bridge either, but that's very much how it should be.
Historically the feature set of ebtables was very limited (it still is), this module was added to pretend packets are routed and invoke the ipv4/ipv6 netfilter hooks from the bridge so users had access to the more feature-rich iptables matching capabilities (including conntrack). nftables doesn't have this limitation, pretty much all features work regardless of the protocol family.
So, br_netfilter is only needed if users, for some reason, need to use ip(6)tables to filter packets forwarded by the bridge, or NAT bridged traffic. For pure link layer filtering, this module isn't needed.
Other Features¶
The Linux bridge also supports IEEE 802.11 Proxy ARP, Media Redundancy Protocol (MRP), Media Redundancy Protocol (MRP) LC mode, IEEE 802.1X port authentication, and MAC Authentication Bypass (MAB).
FAQ¶
What does a bridge do?¶
A bridge transparently forwards traffic between multiple network interfaces. In plain English this means that a bridge connects two or more physical Ethernet networks, to form one larger (logical) Ethernet network.
Is it L3 protocol independent?¶
Yes. The bridge sees all frames, but it uses only L2 headers/information. As such, the bridging functionality is protocol independent, and there should be no trouble forwarding IPX, NetBEUI, IP, IPv6, etc.
Contact Info¶
The code is currently maintained by Roopa Prabhu <roopa@nvidia.com> and Nikolay Aleksandrov <razor@blackwall.org>. Bridge bugs and enhancements are discussed on the linux-netdev mailing list netdev@vger.kernel.org and bridge@lists.linux-foundation.org.
The list is open to anyone interested: http://vger.kernel.org/vger-lists.html#netdev
External Links¶
The old Documentation for Linux bridging is on: https://wiki.linuxfoundation.org/networking/bridge