Net DIM - Generic Network Dynamic Interrupt Moderation¶
- Author
Tal Gilboa <talgi@mellanox.com>
Contents
Assumptions¶
This document assumes the reader has basic knowledge in network drivers and in general interrupt moderation.
Introduction¶
Dynamic Interrupt Moderation (DIM) (in networking) refers to changing the interrupt moderation configuration of a channel in order to optimize packet processing. The mechanism includes an algorithm which decides if and how to change moderation parameters for a channel, usually by performing an analysis on runtime data sampled from the system. Net DIM is such a mechanism. In each iteration of the algorithm, it analyses a given sample of the data, compares it to the previous sample and if required, it can decide to change some of the interrupt moderation configuration fields. The data sample is composed of data bandwidth, the number of packets and the number of events. The time between samples is also measured. Net DIM compares the current and the previous data and returns an adjusted interrupt moderation configuration object. In some cases, the algorithm might decide not to change anything. The configuration fields are the minimum duration (microseconds) allowed between events and the maximum number of wanted packets per event. The Net DIM algorithm ascribes importance to increase bandwidth over reducing interrupt rate.
Net DIM Algorithm¶
Each iteration of the Net DIM algorithm follows these steps:
Calculates new data sample.
Compares it to previous sample.
Makes a decision - suggests interrupt moderation configuration fields.
Applies a schedule work function, which applies suggested configuration.
The first two steps are straightforward, both the new and the previous data are supplied by the driver registered to Net DIM. The previous data is the new data supplied to the previous iteration. The comparison step checks the difference between the new and previous data and decides on the result of the last step. A step would result as "better" if bandwidth increases and as "worse" if bandwidth reduces. If there is no change in bandwidth, the packet rate is compared in a similar fashion - increase == "better" and decrease == "worse". In case there is no change in the packet rate as well, the interrupt rate is compared. Here the algorithm tries to optimize for lower interrupt rate so an increase in the interrupt rate is considered "worse" and a decrease is considered "better". Step #2 has an optimization for avoiding false results: it only considers a difference between samples as valid if it is greater than a certain percentage. Also, since Net DIM does not measure anything by itself, it assumes the data provided by the driver is valid.
Step #3 decides on the suggested configuration based on the result from step #2 and the internal state of the algorithm. The states reflect the "direction" of the algorithm: is it going left (reducing moderation), right (increasing moderation) or standing still. Another optimization is that if a decision to stay still is made multiple times, the interval between iterations of the algorithm would increase in order to reduce calculation overhead. Also, after "parking" on one of the most left or most right decisions, the algorithm may decide to verify this decision by taking a step in the other direction. This is done in order to avoid getting stuck in a "deep sleep" scenario. Once a decision is made, an interrupt moderation configuration is selected from the predefined profiles.
The last step is to notify the registered driver that it should apply the suggested configuration. This is done by scheduling a work function, defined by the Net DIM API and provided by the registered driver.
As you can see, Net DIM itself does not actively interact with the system. It would have trouble making the correct decisions if the wrong data is supplied to it and it would be useless if the work function would not apply the suggested configuration. This does, however, allow the registered driver some room for manoeuvre as it may provide partial data or ignore the algorithm suggestion under some conditions.
Registering a Network Device to DIM¶
Net DIM API exposes the main function net_dim()
.
This function is the entry point to the Net
DIM algorithm and has to be called every time the driver would like to check if
it should change interrupt moderation parameters. The driver should provide two
data structures: struct dim
and
struct dim_sample
. struct dim
describes the state of DIM for a specific object (RX queue, TX queue,
other queues, etc.). This includes the current selected profile, previous data
samples, the callback function provided by the driver and more.
struct dim_sample
describes a data sample,
which will be compared to the data sample stored in struct dim
in order to decide on the algorithm's next
step. The sample should include bytes, packets and interrupts, measured by
the driver.
In order to use Net DIM from a networking driver, the driver needs to call the
main net_dim()
function. The recommended method is to call net_dim()
on each
interrupt. Since Net DIM has a built-in moderation and it might decide to skip
iterations under certain conditions, there is no need to moderate the net_dim()
calls as well. As mentioned above, the driver needs to provide an object of type
struct dim
to the net_dim()
function call. It is advised for
each entity using Net DIM to hold a struct dim
as part of its
data structure and use it as the main Net DIM API object.
The struct dim_sample
should hold the latest
bytes, packets and interrupts count. No need to perform any calculations, just
include the raw data.
The net_dim()
call itself does not return anything. Instead Net DIM relies on
the driver to provide a callback function, which is called when the algorithm
decides to make a change in the interrupt moderation parameters. This callback
will be scheduled and run in a separate thread in order not to add overhead to
the data flow. After the work is done, Net DIM algorithm needs to be set to
the proper state in order to move to the next iteration.
Example¶
The following code demonstrates how to register a driver to Net DIM. The actual usage is not complete but it should make the outline of the usage clear.
#include <linux/dim.h>
/* Callback for net DIM to schedule on a decision to change moderation */
void my_driver_do_dim_work(struct work_struct *work)
{
/* Get struct dim from struct work_struct */
struct dim *dim = container_of(work, struct dim,
work);
/* Do interrupt moderation related stuff */
...
/* Signal net DIM work is done and it should move to next iteration */
dim->state = DIM_START_MEASURE;
}
/* My driver's interrupt handler */
int my_driver_handle_interrupt(struct my_driver_entity *my_entity, ...)
{
...
/* A struct to hold current measured data */
struct dim_sample dim_sample;
...
/* Initiate data sample struct with current data */
dim_update_sample(my_entity->events,
my_entity->packets,
my_entity->bytes,
&dim_sample);
/* Call net DIM */
net_dim(&my_entity->dim, dim_sample);
...
}
/* My entity's initialization function (my_entity was already allocated) */
int my_driver_init_my_entity(struct my_driver_entity *my_entity, ...)
{
...
/* Initiate struct work_struct with my driver's callback function */
INIT_WORK(&my_entity->dim.work, my_driver_do_dim_work);
...
}
Dynamic Interrupt Moderation (DIM) library API¶
-
struct dim_cq_moder¶
Structure for CQ moderation values. Used for communications between DIM and its consumer.
Definition:
struct dim_cq_moder {
u16 usec;
u16 pkts;
u16 comps;
u8 cq_period_mode;
};
Members
usec
CQ timer suggestion (by DIM)
pkts
CQ packet counter suggestion (by DIM)
comps
Completion counter
cq_period_mode
CQ period count mode (from CQE/EQE)
-
struct dim_sample¶
Structure for DIM sample data. Used for communications between DIM and its consumer.
Definition:
struct dim_sample {
ktime_t time;
u32 pkt_ctr;
u32 byte_ctr;
u16 event_ctr;
u32 comp_ctr;
};
Members
time
Sample timestamp
pkt_ctr
Number of packets
byte_ctr
Number of bytes
event_ctr
Number of events
comp_ctr
Current completion counter
-
struct dim_stats¶
Structure for DIM stats. Used for holding current measured rates.
Definition:
struct dim_stats {
int ppms;
int bpms;
int epms;
int cpms;
int cpe_ratio;
};
Members
ppms
Packets per msec
bpms
Bytes per msec
epms
Events per msec
cpms
Completions per msec
cpe_ratio
Ratio of completions to events
-
struct dim¶
Main structure for dynamic interrupt moderation (DIM). Used for holding all information about a specific DIM instance.
Definition:
struct dim {
u8 state;
struct dim_stats prev_stats;
struct dim_sample start_sample;
struct dim_sample measuring_sample;
struct work_struct work;
void *priv;
u8 profile_ix;
u8 mode;
u8 tune_state;
u8 steps_right;
u8 steps_left;
u8 tired;
};
Members
state
Algorithm state (see below)
prev_stats
Measured rates from previous iteration (for comparison)
start_sample
Sampled data at start of current iteration
measuring_sample
A
dim_sample
that is used to update the current eventswork
Work to perform on action required
priv
A pointer to the struct that points to dim
profile_ix
Current moderation profile
mode
CQ period count mode
tune_state
Algorithm tuning state (see below)
steps_right
Number of steps taken towards higher moderation
steps_left
Number of steps taken towards lower moderation
tired
Parking depth counter
-
enum dim_cq_period_mode¶
Modes for CQ period count
Constants
DIM_CQ_PERIOD_MODE_START_FROM_EQE
Start counting from EQE
DIM_CQ_PERIOD_MODE_START_FROM_CQE
Start counting from CQE (implies timer reset)
DIM_CQ_PERIOD_NUM_MODES
Number of modes
-
enum dim_state¶
DIM algorithm states
Constants
DIM_START_MEASURE
This is the first iteration (also after applying a new profile)
DIM_MEASURE_IN_PROGRESS
Algorithm is already in progress - check if need to perform an action
DIM_APPLY_NEW_PROFILE
DIM consumer is currently applying a profile - no need to measure
Description
These will determine if the algorithm is in a valid state to start an iteration.
-
enum dim_tune_state¶
DIM algorithm tune states
Constants
DIM_PARKING_ON_TOP
Algorithm found a local top point - exit on significant difference
DIM_PARKING_TIRED
Algorithm found a deep top point - don't exit if tired > 0
DIM_GOING_RIGHT
Algorithm is currently trying higher moderation levels
DIM_GOING_LEFT
Algorithm is currently trying lower moderation levels
Description
These will determine which action the algorithm should perform.
-
enum dim_stats_state¶
DIM algorithm statistics states
Constants
DIM_STATS_WORSE
Current iteration shows worse performance than before
DIM_STATS_SAME
Current iteration shows same performance than before
DIM_STATS_BETTER
Current iteration shows better performance than before
Description
These will determine the verdict of current iteration.
-
enum dim_step_result¶
DIM algorithm step results
Constants
DIM_STEPPED
Performed a regular step
DIM_TOO_TIRED
Same kind of step was done multiple times - should go to tired parking
DIM_ON_EDGE
Stepped to the most left/right profile
Description
These describe the result of a step.
Parameters
struct dim *dim
DIM context
Description
Check if current profile is a good place to park at. This will result in reducing the DIM checks frequency as we assume we shouldn't probably change profiles, unless traffic pattern wasn't changed.
Parameters
struct dim *dim
DIM context
Description
Go left if we were going right and vice-versa. Do nothing if currently parking.
Parameters
struct dim *dim
DIM context
Description
Enter parking state. Clear all movement history.
Parameters
struct dim *dim
DIM context
Description
Enter parking state. Clear all movement history and cause DIM checks frequency to reduce.
-
bool dim_calc_stats(struct dim_sample *start, struct dim_sample *end, struct dim_stats *curr_stats)¶
calculate the difference between two samples
Parameters
struct dim_sample *start
start sample
struct dim_sample *end
end sample
struct dim_stats *curr_stats
delta between samples
Description
Calculate the delta between two samples (in data rates). Takes into consideration counter wrap-around. Returned boolean indicates whether curr_stats are reliable.
-
void dim_update_sample(u16 event_ctr, u64 packets, u64 bytes, struct dim_sample *s)¶
set a sample's fields with given values
Parameters
u16 event_ctr
number of events to set
u64 packets
number of packets to set
u64 bytes
number of bytes to set
struct dim_sample *s
DIM sample
-
void dim_update_sample_with_comps(u16 event_ctr, u64 packets, u64 bytes, u64 comps, struct dim_sample *s)¶
set a sample's fields with given values including the completion parameter
Parameters
u16 event_ctr
number of events to set
u64 packets
number of packets to set
u64 bytes
number of bytes to set
u64 comps
number of completions to set
struct dim_sample *s
DIM sample
-
struct dim_cq_moder net_dim_get_rx_moderation(u8 cq_period_mode, int ix)¶
provide a CQ moderation object for the given RX profile
Parameters
u8 cq_period_mode
CQ period mode
int ix
Profile index
-
struct dim_cq_moder net_dim_get_def_rx_moderation(u8 cq_period_mode)¶
provide the default RX moderation
Parameters
u8 cq_period_mode
CQ period mode
-
struct dim_cq_moder net_dim_get_tx_moderation(u8 cq_period_mode, int ix)¶
provide a CQ moderation object for the given TX profile
Parameters
u8 cq_period_mode
CQ period mode
int ix
Profile index
-
struct dim_cq_moder net_dim_get_def_tx_moderation(u8 cq_period_mode)¶
provide the default TX moderation
Parameters
u8 cq_period_mode
CQ period mode
-
void net_dim(struct dim *dim, struct dim_sample end_sample)¶
main DIM algorithm entry point
Parameters
struct dim *dim
DIM instance information
struct dim_sample end_sample
Current data measurement
Description
Called by the consumer. This is the main logic of the algorithm, where data is processed in order to decide on next required action.
Parameters
struct dim *dim
The moderation struct.
u64 completions
The number of completions collected in this round.
Description
Each call to rdma_dim takes the latest amount of completions that have been collected and counts them as a new event. Once enough events have been collected the algorithm decides a new moderation level.