Compute Express Link Memory Devices¶
A Compute Express Link Memory Device is a CXL component that implements the CXL.mem protocol. It contains some amount of volatile memory, persistent memory, or both. It is enumerated as a PCI device for configuration and passing messages over an MMIO mailbox. Its contribution to the System Physical Address space is handled via HDM (Host Managed Device Memory) decoders that optionally define a device's contribution to an interleaved address range across multiple devices underneath a host-bridge or interleaved across host-bridges.
CXL Bus: Theory of Operation¶
Similar to how a RAID driver takes disk objects and assembles them into a new logical device, the CXL subsystem is tasked to take PCIe and ACPI objects and assemble them into a CXL.mem decode topology. The need for runtime configuration of the CXL.mem topology is also similar to RAID in that different environments with the same hardware configuration may decide to assemble the topology in contrasting ways. One may choose performance (RAID0) striping memory across multiple Host Bridges and endpoints while another may opt for fault tolerance and disable any striping in the CXL.mem topology.
Platform firmware enumerates a menu of interleave options at the "CXL root port" (Linux term for the top of the CXL decode topology). From there, PCIe topology dictates which endpoints can participate in which Host Bridge decode regimes. Each PCIe Switch in the path between the root and an endpoint introduces a point at which the interleave can be split. For example platform firmware may say at a given range only decodes to 1 one Host Bridge, but that Host Bridge may in turn interleave cycles across multiple Root Ports. An intervening Switch between a port and an endpoint may interleave cycles across multiple Downstream Switch Ports, etc.
Here is a sample listing of a CXL topology defined by 'cxl_test'. The 'cxl_test' module generates an emulated CXL topology of 2 Host Bridges each with 2 Root Ports. Each of those Root Ports are connected to 2-way switches with endpoints connected to those downstream ports for a total of 8 endpoints:
# cxl list -BEMPu -b cxl_test
{
"bus":"root3",
"provider":"cxl_test",
"ports:root3":[
{
"port":"port5",
"host":"cxl_host_bridge.1",
"ports:port5":[
{
"port":"port8",
"host":"cxl_switch_uport.1",
"endpoints:port8":[
{
"endpoint":"endpoint9",
"host":"mem2",
"memdev":{
"memdev":"mem2",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x1",
"numa_node":1,
"host":"cxl_mem.1"
}
},
{
"endpoint":"endpoint15",
"host":"mem6",
"memdev":{
"memdev":"mem6",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x5",
"numa_node":1,
"host":"cxl_mem.5"
}
}
]
},
{
"port":"port12",
"host":"cxl_switch_uport.3",
"endpoints:port12":[
{
"endpoint":"endpoint17",
"host":"mem8",
"memdev":{
"memdev":"mem8",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x7",
"numa_node":1,
"host":"cxl_mem.7"
}
},
{
"endpoint":"endpoint13",
"host":"mem4",
"memdev":{
"memdev":"mem4",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x3",
"numa_node":1,
"host":"cxl_mem.3"
}
}
]
}
]
},
{
"port":"port4",
"host":"cxl_host_bridge.0",
"ports:port4":[
{
"port":"port6",
"host":"cxl_switch_uport.0",
"endpoints:port6":[
{
"endpoint":"endpoint7",
"host":"mem1",
"memdev":{
"memdev":"mem1",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0",
"numa_node":0,
"host":"cxl_mem.0"
}
},
{
"endpoint":"endpoint14",
"host":"mem5",
"memdev":{
"memdev":"mem5",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x4",
"numa_node":0,
"host":"cxl_mem.4"
}
}
]
},
{
"port":"port10",
"host":"cxl_switch_uport.2",
"endpoints:port10":[
{
"endpoint":"endpoint16",
"host":"mem7",
"memdev":{
"memdev":"mem7",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x6",
"numa_node":0,
"host":"cxl_mem.6"
}
},
{
"endpoint":"endpoint11",
"host":"mem3",
"memdev":{
"memdev":"mem3",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x2",
"numa_node":0,
"host":"cxl_mem.2"
}
}
]
}
]
}
]
}
In that listing each "root", "port", and "endpoint" object correspond a kernel
'struct cxl_port
' object. A 'cxl_port' is a device that can decode CXL.mem to
its descendants. So "root" claims non-PCIe enumerable platform decode ranges and
decodes them to "ports", "ports" decode to "endpoints", and "endpoints"
represent the decode from SPA (System Physical Address) to DPA (Device Physical
Address).
Continuing the RAID analogy, disks have both topology metadata and on device metadata that determine RAID set assembly. CXL Port topology and CXL Port link status is metadata for CXL.mem set assembly. The CXL Port topology is enumerated by the arrival of a CXL.mem device. I.e. unless and until the PCIe core attaches the cxl_pci driver to a CXL Memory Expander there is no role for CXL Port objects. Conversely for hot-unplug / removal scenarios, there is no need for the Linux PCI core to tear down switch-level CXL resources because the endpoint ->remove() event cleans up the port data that was established to support that Memory Expander.
The port metadata and potential decode schemes that a give memory device may participate can be determined via a command like:
# cxl list -BDMu -d root -m mem3
{
"bus":"root3",
"provider":"cxl_test",
"decoders:root3":[
{
"decoder":"decoder3.1",
"resource":"0x8030000000",
"size":"512.00 MiB (536.87 MB)",
"volatile_capable":true,
"nr_targets":2
},
{
"decoder":"decoder3.3",
"resource":"0x8060000000",
"size":"512.00 MiB (536.87 MB)",
"pmem_capable":true,
"nr_targets":2
},
{
"decoder":"decoder3.0",
"resource":"0x8020000000",
"size":"256.00 MiB (268.44 MB)",
"volatile_capable":true,
"nr_targets":1
},
{
"decoder":"decoder3.2",
"resource":"0x8050000000",
"size":"256.00 MiB (268.44 MB)",
"pmem_capable":true,
"nr_targets":1
}
],
"memdevs:root3":[
{
"memdev":"mem3",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x2",
"numa_node":0,
"host":"cxl_mem.2"
}
]
}
...which queries the CXL topology to ask "given CXL Memory Expander with a kernel device name of 'mem3' which platform level decode ranges may this device participate". A given expander can participate in multiple CXL.mem interleave sets simultaneously depending on how many decoder resource it has. In this example mem3 can participate in one or more of a PMEM interleave that spans to Host Bridges, a PMEM interleave that targets a single Host Bridge, a Volatile memory interleave that spans 2 Host Bridges, and a Volatile memory interleave that only targets a single Host Bridge.
Conversely the memory devices that can participate in a given platform level decode scheme can be determined via a command like the following:
# cxl list -MDu -d 3.2
[
{
"memdevs":[
{
"memdev":"mem1",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0",
"numa_node":0,
"host":"cxl_mem.0"
},
{
"memdev":"mem5",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x4",
"numa_node":0,
"host":"cxl_mem.4"
},
{
"memdev":"mem7",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x6",
"numa_node":0,
"host":"cxl_mem.6"
},
{
"memdev":"mem3",
"pmem_size":"256.00 MiB (268.44 MB)",
"ram_size":"256.00 MiB (268.44 MB)",
"serial":"0x2",
"numa_node":0,
"host":"cxl_mem.2"
}
]
},
{
"root decoders":[
{
"decoder":"decoder3.2",
"resource":"0x8050000000",
"size":"256.00 MiB (268.44 MB)",
"pmem_capable":true,
"nr_targets":1
}
]
}
]
...where the naming scheme for decoders is "decoder<port_id>.<instance_id>".
Driver Infrastructure¶
This section covers the driver infrastructure for a CXL memory device.
CXL Memory Device¶
This implements the PCI exclusive functionality for a CXL device as it is defined by the Compute Express Link specification. CXL devices may surface certain functionality even if it isn't CXL enabled. While this driver is focused around the PCI specific aspects of a CXL device, it binds to the specific CXL memory device class code, and therefore the implementation of cxl_pci is focused around CXL memory devices.
- The driver has several responsibilities, mainly:
Create the memX device and register on the CXL bus.
Enumerate device's register interface and map them.
Registers nvdimm bridge device with cxl_core.
Registers a CXL mailbox with cxl_core.
-
int __cxl_pci_mbox_send_cmd(struct cxl_memdev_state *mds, struct cxl_mbox_cmd *mbox_cmd)¶
Execute a mailbox command
Parameters
struct cxl_memdev_state *mds
The memory device driver data
struct cxl_mbox_cmd *mbox_cmd
Command to send to the memory device.
Context
Any context. Expects mbox_mutex to be held.
Return
- -ETIMEDOUT if timeout occurred waiting for completion. 0 on success.
Caller should check the return code in mbox_cmd to make sure it succeeded.
Description
This is a generic form of the CXL mailbox send command thus only using the registers defined by the mailbox capability ID - CXL 2.0 8.2.8.4. Memory devices, and perhaps other types of CXL devices may have further information available upon error conditions. Driver facilities wishing to send mailbox commands should use the wrapper command.
The CXL spec allows for up to two mailboxes. The intention is for the primary mailbox to be OS controlled and the secondary mailbox to be used by system firmware. This allows the OS and firmware to communicate with the device and not need to coordinate with each other. The driver only uses the primary mailbox.
CXL memory endpoint devices and switches are CXL capable devices that are participating in CXL.mem protocol. Their functionality builds on top of the CXL.io protocol that allows enumerating and configuring components via standard PCI mechanisms.
The cxl_mem driver owns kicking off the enumeration of this CXL.mem capability. With the detection of a CXL capable endpoint, the driver will walk up to find the platform specific port it is connected to, and determine if there are intervening switches in the path. If there are switches, a secondary action is to enumerate those (implemented in cxl_core). Finally the cxl_mem driver adds the device it is bound to as a CXL endpoint-port for use in higher level operations.
CXL Port¶
The port driver enumerates dport via PCI and scans for HDM (Host-managed-Device-Memory) decoder resources via the component_reg_phys value passed in by the agent that registered the port. All descendant ports of a CXL root port (described by platform firmware) are managed in this drivers context. Each driver instance is responsible for tearing down the driver context of immediate descendant ports. The locking for this is validated by CONFIG_PROVE_CXL_LOCKING.
The primary service this driver provides is presenting APIs to other drivers to utilize the decoders, and indicating to userspace (via bind status) the connectivity of the CXL.mem protocol throughout the PCIe topology.
CXL Core¶
The CXL core objects like ports, decoders, and regions are shared between the subsystem drivers cxl_acpi, cxl_pci, and core drivers (port-driver, region-driver, nvdimm object-drivers... etc).
-
struct cxl_register_map¶
DVSEC harvested register block mapping parameters
Definition:
struct cxl_register_map {
struct device *dev;
void __iomem *base;
resource_size_t resource;
resource_size_t max_size;
u8 reg_type;
union {
struct cxl_component_reg_map component_map;
struct cxl_device_reg_map device_map;
struct cxl_pmu_reg_map pmu_map;
};
};
Members
dev
device for devm operations and logging
base
virtual base of the register-block-BAR + block_offset
resource
physical resource base of the register block
max_size
maximum mapping size to perform register search
reg_type
see enum cxl_regloc_type
{unnamed_union}
anonymous
component_map
cxl_reg_map for component registers
device_map
cxl_reg_maps for device registers
pmu_map
cxl_reg_maps for CXL Performance Monitoring Units
-
struct cxl_decoder¶
Common CXL HDM Decoder Attributes
Definition:
struct cxl_decoder {
struct device dev;
int id;
struct range hpa_range;
int interleave_ways;
int interleave_granularity;
enum cxl_decoder_type target_type;
struct cxl_region *region;
unsigned long flags;
int (*commit)(struct cxl_decoder *cxld);
int (*reset)(struct cxl_decoder *cxld);
};
Members
dev
this decoder's device
id
kernel device name id
hpa_range
Host physical address range mapped by this decoder
interleave_ways
number of cxl_dports in this decode
interleave_granularity
data stride per dport
target_type
accelerator vs expander (type2 vs type3) selector
region
currently assigned region for this decoder
flags
memory type capabilities and locking
commit
device/decoder-type specific callback to commit settings to hw
reset
device/decoder-type specific callback to reset hw settings
-
struct cxl_endpoint_decoder¶
Endpoint / SPA to DPA decoder
Definition:
struct cxl_endpoint_decoder {
struct cxl_decoder cxld;
struct resource *dpa_res;
resource_size_t skip;
enum cxl_decoder_mode mode;
enum cxl_decoder_state state;
int pos;
};
Members
cxld
base cxl_decoder_object
dpa_res
actively claimed DPA span of this decoder
skip
offset into dpa_res where cxld.hpa_range maps
mode
which memory type / access-mode-partition this decoder targets
state
autodiscovery state
pos
interleave position in cxld.region
-
struct cxl_switch_decoder¶
Switch specific CXL HDM Decoder
Definition:
struct cxl_switch_decoder {
struct cxl_decoder cxld;
seqlock_t target_lock;
int nr_targets;
struct cxl_dport *target[];
};
Members
cxld
base cxl_decoder object
target_lock
coordinate coherent reads of the target list
nr_targets
number of elements in target
target
active ordered target list in current decoder configuration
Description
The 'switch' decoder type represents the decoder instances of cxl_port's that route from the root of a CXL memory decode topology to the endpoints. They come in two flavors, root-level decoders, statically defined by platform firmware, and mid-level decoders, where interleave-granularity, interleave-width, and the target list are mutable.
-
struct cxl_root_decoder¶
Static platform CXL address decoder
Definition:
struct cxl_root_decoder {
struct resource *res;
atomic_t region_id;
cxl_calc_hb_fn calc_hb;
void *platform_data;
struct mutex range_lock;
struct cxl_switch_decoder cxlsd;
};
Members
res
host / parent resource for region allocations
region_id
region id for next region provisioning event
calc_hb
which host bridge covers the n'th position by granularity
platform_data
platform specific configuration data
range_lock
sync region autodiscovery by address range
cxlsd
base cxl switch decoder
-
struct cxl_region_params¶
region settings
Definition:
struct cxl_region_params {
enum cxl_config_state state;
uuid_t uuid;
int interleave_ways;
int interleave_granularity;
struct resource *res;
struct cxl_endpoint_decoder *targets[CXL_DECODER_MAX_INTERLEAVE];
int nr_targets;
};
Members
state
allow the driver to lockdown further parameter changes
uuid
unique id for persistent regions
interleave_ways
number of endpoints in the region
interleave_granularity
capacity each endpoint contributes to a stripe
res
allocated iomem capacity for this region
targets
active ordered targets in current decoder configuration
nr_targets
number of targets
Description
State transitions are protected by the cxl_region_rwsem
-
struct cxl_region¶
CXL region
Definition:
struct cxl_region {
struct device dev;
int id;
enum cxl_decoder_mode mode;
enum cxl_decoder_type type;
struct cxl_nvdimm_bridge *cxl_nvb;
struct cxl_pmem_region *cxlr_pmem;
unsigned long flags;
struct cxl_region_params params;
};
Members
dev
This region's device
id
This region's id. Id is globally unique across all regions
mode
Endpoint decoder allocation / access mode
type
Endpoint decoder target type
cxl_nvb
nvdimm bridge for coordinating cxlr_pmem setup / shutdown
cxlr_pmem
(for pmem regions) cached copy of the nvdimm bridge
flags
Region state flags
params
active + config params for the region
-
struct cxl_port¶
logical collection of upstream port devices and downstream port devices to construct a CXL memory decode hierarchy.
Definition:
struct cxl_port {
struct device dev;
struct device *uport_dev;
struct device *host_bridge;
int id;
struct xarray dports;
struct xarray endpoints;
struct xarray regions;
struct cxl_dport *parent_dport;
struct ida decoder_ida;
struct cxl_register_map comp_map;
int nr_dports;
int hdm_end;
int commit_end;
resource_size_t component_reg_phys;
bool dead;
unsigned int depth;
struct cxl_cdat {
void *table;
size_t length;
} cdat;
bool cdat_available;
};
Members
dev
this port's device
uport_dev
PCI or platform device implementing the upstream port capability
host_bridge
Shortcut to the platform attach point for this port
id
id for port device-name
dports
cxl_dport instances referenced by decoders
endpoints
cxl_ep instances, endpoints that are a descendant of this port
regions
cxl_region_ref instances, regions mapped by this port
parent_dport
dport that points to this port in the parent
decoder_ida
allocator for decoder ids
comp_map
component register capability mappings
nr_dports
number of entries in dports
hdm_end
track last allocated HDM decoder instance for allocation ordering
commit_end
cursor to track highest committed decoder for commit ordering
component_reg_phys
component register capability base address (optional)
dead
last ep has been removed, force port re-creation
depth
How deep this port is relative to the root. depth 0 is the root.
cdat
Cached CDAT data
cdat_available
Should a CDAT attribute be available in sysfs
-
struct cxl_dport¶
CXL downstream port
Definition:
struct cxl_dport {
struct device *dport_dev;
struct cxl_register_map comp_map;
int port_id;
struct cxl_rcrb_info rcrb;
bool rch;
struct cxl_port *port;
};
Members
dport_dev
PCI bridge or firmware device representing the downstream link
comp_map
component register capability mappings
port_id
unique hardware identifier for dport in decoder target list
rcrb
Data about the Root Complex Register Block layout
rch
Indicate whether this dport was enumerated in RCH or VH mode
port
reference to cxl_port that contains this downstream port
-
struct cxl_ep¶
track an endpoint's interest in a port
Definition:
struct cxl_ep {
struct device *ep;
struct cxl_dport *dport;
struct cxl_port *next;
};
Members
ep
device that hosts a generic CXL endpoint (expander or accelerator)
dport
which dport routes to this endpoint on port
next
cxl switch port across the link attached to dport NULL if attached to an endpoint
-
struct cxl_region_ref¶
track a region's interest in a port
Definition:
struct cxl_region_ref {
struct cxl_port *port;
struct cxl_decoder *decoder;
struct cxl_region *region;
struct xarray endpoints;
int nr_targets_set;
int nr_eps;
int nr_targets;
};
Members
port
point in topology to install this reference
decoder
decoder assigned for region in port
region
region for this reference
endpoints
cxl_ep references for region members beneath port
nr_targets_set
track how many targets have been programmed during setup
nr_eps
number of endpoints beneath port
nr_targets
number of distinct targets needed to reach nr_eps
-
struct cxl_endpoint_dvsec_info¶
Cached DVSEC info
Definition:
struct cxl_endpoint_dvsec_info {
bool mem_enabled;
int ranges;
struct cxl_port *port;
struct range dvsec_range[2];
};
Members
mem_enabled
cached value of mem_enabled in the DVSEC at init time
ranges
Number of active HDM ranges this device uses.
port
endpoint port associated with this info instance
dvsec_range
cached attributes of the ranges in the DVSEC, PCIE_DEVICE
The CXL core provides a set of interfaces that can be consumed by CXL aware drivers. The interfaces allow for creation, modification, and destruction of regions, memory devices, ports, and decoders. CXL aware drivers must register with the CXL core via these interfaces in order to be able to participate in cross-device interleave coordination. The CXL core also establishes and maintains the bridge to the nvdimm subsystem.
CXL core introduces sysfs hierarchy to control the devices that are instantiated by the core.
-
struct cxl_port *devm_cxl_add_port(struct device *host, struct device *uport_dev, resource_size_t component_reg_phys, struct cxl_dport *parent_dport)¶
register a cxl_port in CXL memory decode hierarchy
Parameters
struct device *host
host device for devm operations
struct device *uport_dev
"physical" device implementing this upstream port
resource_size_t component_reg_phys
(optional) for configurable cxl_port instances
struct cxl_dport *parent_dport
next hop up in the CXL memory decode hierarchy
-
struct cxl_dport *devm_cxl_add_dport(struct cxl_port *port, struct device *dport_dev, int port_id, resource_size_t component_reg_phys)¶
append VH downstream port data to a cxl_port
Parameters
struct cxl_port *port
the cxl_port that references this dport
struct device *dport_dev
firmware or PCI device representing the dport
int port_id
identifier for this dport in a decoder's target list
resource_size_t component_reg_phys
optional location of CXL component registers
Description
Note that dports are appended to the devm release action's of the either the port's host (for root ports), or the port itself (for switch ports)
-
struct cxl_dport *devm_cxl_add_rch_dport(struct cxl_port *port, struct device *dport_dev, int port_id, resource_size_t rcrb)¶
append RCH downstream port data to a cxl_port
Parameters
struct cxl_port *port
the cxl_port that references this dport
struct device *dport_dev
firmware or PCI device representing the dport
int port_id
identifier for this dport in a decoder's target list
resource_size_t rcrb
mandatory location of a Root Complex Register Block
Description
See CXL 3.0 9.11.8 CXL Devices Attached to an RCH
-
int cxl_add_ep(struct cxl_dport *dport, struct device *ep_dev)¶
register an endpoint's interest in a port
Parameters
struct cxl_dport *dport
the dport that routes to ep_dev
struct device *ep_dev
device representing the endpoint
Description
Intermediate CXL ports are scanned based on the arrival of endpoints. When those endpoints depart the port can be destroyed once all endpoints that care about that port have been removed.
-
int cxl_decoder_init(struct cxl_port *port, struct cxl_decoder *cxld)¶
Common decoder setup / initialization
Parameters
struct cxl_port *port
owning port of this decoder
struct cxl_decoder *cxld
common decoder properties to initialize
Description
A port may contain one or more decoders. Each of those decoders
enable some address space for CXL.mem utilization. A decoder is
expected to be configured by the caller before registering via
cxl_decoder_add()
-
struct cxl_root_decoder *cxl_root_decoder_alloc(struct cxl_port *port, unsigned int nr_targets, cxl_calc_hb_fn calc_hb)¶
Allocate a root level decoder
Parameters
struct cxl_port *port
owning CXL root of this decoder
unsigned int nr_targets
static number of downstream targets
cxl_calc_hb_fn calc_hb
which host bridge covers the n'th position by granularity
Return
A new cxl decoder to be registered by cxl_decoder_add()
. A
'CXL root' decoder is one that decodes from a top-level / static platform
firmware description of CXL resources into a CXL standard decode
topology.
-
struct cxl_switch_decoder *cxl_switch_decoder_alloc(struct cxl_port *port, unsigned int nr_targets)¶
Allocate a switch level decoder
Parameters
struct cxl_port *port
owning CXL switch port of this decoder
unsigned int nr_targets
max number of dynamically addressable downstream targets
Return
A new cxl decoder to be registered by cxl_decoder_add()
. A
'switch' decoder is any decoder that can be enumerated by PCIe
topology and the HDM Decoder Capability. This includes the decoders
that sit between Switch Upstream Ports / Switch Downstream Ports and
Host Bridges / Root Ports.
-
struct cxl_endpoint_decoder *cxl_endpoint_decoder_alloc(struct cxl_port *port)¶
Allocate an endpoint decoder
Parameters
struct cxl_port *port
owning port of this decoder
Return
A new cxl decoder to be registered by cxl_decoder_add()
-
int cxl_decoder_add_locked(struct cxl_decoder *cxld, int *target_map)¶
Add a decoder with targets
Parameters
struct cxl_decoder *cxld
The cxl decoder allocated by cxl_<type>_decoder_alloc()
int *target_map
A list of downstream ports that this decoder can direct memory traffic to. These numbers should correspond with the port number in the PCIe Link Capabilities structure.
Description
Certain types of decoders may not have any targets. The main example of this is an endpoint device. A more awkward example is a hostbridge whose root ports get hot added (technically possible, though unlikely).
This is the locked variant of cxl_decoder_add()
.
Context
Process context. Expects the device lock of the port that owns the cxld to be held.
Return
- Negative error code if the decoder wasn't properly configured; else
returns 0.
-
int cxl_decoder_add(struct cxl_decoder *cxld, int *target_map)¶
Add a decoder with targets
Parameters
struct cxl_decoder *cxld
The cxl decoder allocated by cxl_<type>_decoder_alloc()
int *target_map
A list of downstream ports that this decoder can direct memory traffic to. These numbers should correspond with the port number in the PCIe Link Capabilities structure.
Description
This is the unlocked variant of cxl_decoder_add_locked()
.
See cxl_decoder_add_locked()
.
Context
Process context. Takes and releases the device lock of the port that owns the cxld.
-
int __cxl_driver_register(struct cxl_driver *cxl_drv, struct module *owner, const char *modname)¶
register a driver for the cxl bus
Parameters
struct cxl_driver *cxl_drv
cxl driver structure to attach
struct module *owner
owning module/driver
const char *modname
KBUILD_MODNAME for parent driver
Compute Express Link protocols are layered on top of PCIe. CXL core provides a set of helpers for CXL interactions which occur via PCIe.
-
int devm_cxl_port_enumerate_dports(struct cxl_port *port)¶
enumerate downstream ports of the upstream port
Parameters
struct cxl_port *port
cxl_port whose ->uport_dev is the upstream of dports to be enumerated
Description
Returns a positive number of dports enumerated or a negative error code.
-
int cxl_hdm_decode_init(struct cxl_dev_state *cxlds, struct cxl_hdm *cxlhdm, struct cxl_endpoint_dvsec_info *info)¶
Setup HDM decoding for the endpoint
Parameters
struct cxl_dev_state *cxlds
Device state
struct cxl_hdm *cxlhdm
Mapped HDM decoder Capability
struct cxl_endpoint_dvsec_info *info
Cached DVSEC range registers info
Description
Try to enable the endpoint's HDM Decoder Capability
Parameters
struct cxl_port *port
Port to read data from
Description
This call will sleep waiting for responses from the DOE mailbox.
The core CXL PMEM infrastructure supports persistent memory provisioning and serves as a bridge to the LIBNVDIMM subsystem. A CXL 'bridge' device is added at the root of a CXL device topology if platform firmware advertises at least one persistent memory capable CXL window. That root-level bridge corresponds to a LIBNVDIMM 'bus' device. Then for each cxl_memdev in the CXL device topology a bridge device is added to host a LIBNVDIMM dimm object. When these bridges are registered native LIBNVDIMM uapis are translated to CXL operations, for example, namespace label access commands.
CXL device capabilities are enumerated by PCI DVSEC (Designated Vendor-specific) and / or descriptors provided by platform firmware. They can be defined as a set like the device and component registers mandated by CXL Section 8.1.12.2 Memory Device PCIe Capabilities and Extended Capabilities, or they can be individual capabilities appended to bridged and endpoint devices.
Provide common infrastructure for enumerating and mapping these discrete capabilities.
Core implementation of the CXL 2.0 Type-3 Memory Device Mailbox. The implementation is used by the cxl_pci driver to initialize the device and implement the cxl_mem.h IOCTL UAPI. It also implements the backend of the cxl_pmem_ctl() transport for LIBNVDIMM.
CXL Regions¶
CXL Regions represent mapped memory capacity in system physical address space. Whereas the CXL Root Decoders identify the bounds of potential CXL Memory ranges, Regions represent the active mapped capacity by the HDM Decoder Capability structures throughout the Host Bridges, Switches, and Endpoints in the topology.
Region configuration has ordering constraints. UUID may be set at any time but is only visible for persistent regions. 1. Interleave granularity 2. Interleave size 3. Decoder targets
-
int cxl_port_attach_region(struct cxl_port *port, struct cxl_region *cxlr, struct cxl_endpoint_decoder *cxled, int pos)¶
track a region's interest in a port by endpoint
Parameters
struct cxl_port *port
port to add a new region reference '
struct cxl_region_ref
'struct cxl_region *cxlr
region to attach to port
struct cxl_endpoint_decoder *cxled
endpoint decoder used to create or further pin a region reference
int pos
interleave position of cxled in cxlr
Description
The attach event is an opportunity to validate CXL decode setup constraints and record metadata needed for programming HDM decoders, in particular decoder target lists.
The steps are:
validate that there are no other regions with a higher HPA already associated with port
establish a region reference if one is not already present
additionally allocate a decoder instance that will host cxlr on port
pin the region reference by the endpoint
account for how many entries in port's target list are needed to cover all of the added endpoints.
-
struct cxl_region *devm_cxl_add_region(struct cxl_root_decoder *cxlrd, int id, enum cxl_decoder_mode mode, enum cxl_decoder_type type)¶
Adds a region to a decoder
Parameters
struct cxl_root_decoder *cxlrd
root decoder
int id
memregion id to create, or memregion_free() on failure
enum cxl_decoder_mode mode
mode for the endpoint decoders of this region
enum cxl_decoder_type type
select whether this is an expander or accelerator (type-2 or type-3)
Description
This is the second step of region initialization. Regions exist within an address space which is mapped by a cxlrd.
Return
0 if the region was added to the cxlrd, else returns negative error code. The region will be named "regionZ" where Z is the unique region number.
-
int devm_cxl_add_pmem_region(struct cxl_region *cxlr)¶
add a cxl_region-to-nd_region bridge
Parameters
struct cxl_region *cxlr
parent CXL region for this pmem region bridge device
Return
0 on success negative error code on failure.
External Interfaces¶
CXL IOCTL Interface¶
Not all of the commands that the driver supports are available for use by userspace at all times. Userspace can check the result of the QUERY command to determine the live set of commands. Alternatively, it can issue the command and check for failure.
-
struct cxl_command_info¶
Command information returned from a query.
Definition:
struct cxl_command_info {
__u32 id;
__u32 flags;
#define CXL_MEM_COMMAND_FLAG_MASK GENMASK(1, 0);
#define CXL_MEM_COMMAND_FLAG_ENABLED BIT(0);
#define CXL_MEM_COMMAND_FLAG_EXCLUSIVE BIT(1);
__u32 size_in;
__u32 size_out;
};
Members
id
ID number for the command.
flags
Flags that specify command behavior.
CXL_MEM_COMMAND_FLAG_USER_ENABLED
The given command id is supported by the driver and is supported by a related opcode on the device.
CXL_MEM_COMMAND_FLAG_EXCLUSIVE
Requests with the given command id will terminate with EBUSY as the kernel actively owns management of the given resource. For example, the label-storage-area can not be written while the kernel is actively managing that space.
size_in
Expected input size, or ~0 if variable length.
size_out
Expected output size, or ~0 if variable length.
Description
Represents a single command that is supported by both the driver and the hardware. This is returned as part of an array from the query ioctl. The following would be a command that takes a variable length input and returns 0 bytes of output.
id = 10
flags = CXL_MEM_COMMAND_FLAG_ENABLED
size_in = ~0
size_out = 0
See struct cxl_mem_query_commands
.
-
struct cxl_mem_query_commands¶
Query supported commands.
Definition:
struct cxl_mem_query_commands {
__u32 n_commands;
__u32 rsvd;
struct cxl_command_info __user commands[];
};
Members
n_commands
In/out parameter. When n_commands is > 0, the driver will return min(num_support_commands, n_commands). When n_commands is 0, driver will return the number of total supported commands.
rsvd
Reserved for future use.
commands
Output array of supported commands. This array must be allocated by userspace to be at least min(num_support_commands, n_commands)
Description
Allow userspace to query the available commands supported by both the driver, and the hardware. Commands that aren't supported by either the driver, or the hardware are not returned in the query.
Examples
{ .n_commands = 0 } // Get number of supported commands
{ .n_commands = 15, .commands = buf } // Return first 15 (or less) supported commands
-
struct cxl_send_command¶
Send a command to a memory device.
Definition:
struct cxl_send_command {
__u32 id;
__u32 flags;
union {
struct {
__u16 opcode;
__u16 rsvd;
} raw;
__u32 rsvd;
};
__u32 retval;
struct {
__u32 size;
__u32 rsvd;
__u64 payload;
} in;
struct {
__u32 size;
__u32 rsvd;
__u64 payload;
} out;
};
Members
id
The command to send to the memory device. This must be one of the commands returned by the query command.
flags
Flags for the command (input).
{unnamed_union}
anonymous
raw
Special fields for raw commands
raw.opcode
Opcode passed to hardware when using the RAW command.
raw.rsvd
Must be zero.
rsvd
Must be zero.
retval
Return value from the memory device (output).
in
Parameters associated with input payload.
in.size
Size of the payload to provide to the device (input).
in.rsvd
Must be zero.
in.payload
Pointer to memory for payload input, payload is little endian.
out
Parameters associated with output payload.
out.size
Size of the payload received from the device (input/output). This field is filled in by userspace to let the driver know how much space was allocated for output. It is populated by the driver to let userspace know how large the output payload actually was.
out.rsvd
Must be zero.
out.payload
Pointer to memory for payload output, payload is little endian.
Description
Mechanism for userspace to send a command to the hardware for processing. The driver will do basic validation on the command sizes. In some cases even the payload may be introspected. Userspace is required to allocate large enough buffers for size_out which can be variable length in certain situations.