Tracepoints in ALSA¶
2017/07/02 Takasahi Sakamoto
Tracepoints in ALSA PCM core¶
ALSA PCM core registers
snd_pcm subsystem to kernel tracepoint system.
This subsystem includes two categories of tracepoints; for state of PCM buffer
and for processing of PCM hardware parameters. These tracepoints are available
when corresponding kernel configurations are enabled. When
is enabled, the latter tracepoints are available. When additional
SND_PCM_XRUN_DEBUG is enabled too, the former trace points are enabled.
Tracepoints for state of PCM buffer¶
This category includes four tracepoints;
Tracepoints for processing of PCM hardware parameters¶
This category includes two tracepoints;
In a design of ALSA PCM core, data transmission is abstracted as PCM substream. Applications manage PCM substream to maintain data transmission for PCM frames. Before starting the data transmission, applications need to configure PCM substream. In this procedure, PCM hardware parameters are decided by interaction between applications and ALSA PCM core. Once decided, runtime of the PCM substream keeps the parameters.
The parameters are described in
struct snd_pcm_hw_params. This
structure includes several types of parameters. Applications set preferable
value to these parameters, then execute ioctl(2) with SNDRV_PCM_IOCTL_HW_REFINE
or SNDRV_PCM_IOCTL_HW_PARAMS. The former is used just for refining available
set of parameters. The latter is used for an actual decision of the parameters.
struct snd_pcm_hw_params structure has below members:
- Configurable. ALSA PCM core and some drivers handle this flag to select convenient parameters or change their behaviour.
Configurable. This type of parameter is described in
struct snd_maskand represent mask values. As of PCM protocol v2.0.13, three types are defined.
Configurable. This type of parameter is described in
struct snd_intervaland represent values with a range. As of PCM protocol v2.0.13, twelve types are defined.
- Configurable. This is evaluated at ioctl(2) with SNDRV_PCM_IOCTL_HW_REFINE only. Applications can select which mask/interval parameter can be changed by ALSA PCM core. For SNDRV_PCM_IOCTL_HW_PARAMS, this mask is ignored and all of parameters are going to be changed.
- Read-only. After returning from ioctl(2), buffer in user space for
struct snd_pcm_hw_paramsincludes result of each operation. This mask represents which mask/interval parameter is actually changed.
- Read-only. This represents hardware/driver capabilities as bit flags with SNDRV_PCM_INFO_XXX. Typically, applications execute ioctl(2) with SNDRV_PCM_IOCTL_HW_REFINE to retrieve this flag, then decide candidates of parameters and execute ioctl(2) with SNDRV_PCM_IOCTL_HW_PARAMS to configure PCM substream.
- Read-only. This value represents available bit width in MSB side of a PCM sample. When a parameter of SNDRV_PCM_HW_PARAM_SAMPLE_BITS was decided as a fixed number, this value is also calculated according to it. Else, zero. But this behaviour depends on implementations in driver side.
- Read-only. This value represents numerator of sampling rate in fraction notation. Basically, when a parameter of SNDRV_PCM_HW_PARAM_RATE was decided as a single value, this value is also calculated according to it. Else, zero. But this behaviour depends on implementations in driver side.
- Read-only. This value represents denominator of sampling rate in fraction notation. Basically, when a parameter of SNDRV_PCM_HW_PARAM_RATE was decided as a single value, this value is also calculated according to it. Else, zero. But this behaviour depends on implementations in driver side.
- Read-only. This value represents the size of FIFO in serial sound interface of hardware. Basically, each driver can assigns a proper value to this parameter but some drivers intentionally set zero with a care of hardware design or data transmission protocol.
ALSA PCM core handles buffer of
struct snd_pcm_hw_params when
applications execute ioctl(2) with SNDRV_PCM_HW_REFINE or SNDRV_PCM_HW_PARAMS.
Parameters in the buffer are changed according to
struct snd_pcm_hardware and rules of constraints in the runtime. The
structure describes capabilities of handled hardware. The rules describes
dependencies on which a parameter is decided according to several parameters.
A rule has a callback function, and drivers can register arbitrary functions
to compute the target parameter. ALSA PCM core registers some rules to the
runtime as a default.
Each driver can join in the interaction as long as it prepared for two stuffs
in a callback of
- In the callback, drivers are expected to change a member of
struct snd_pcm_hardwaretype in the runtime, according to capacities of corresponding hardware.
- In the same callback, drivers are also expected to register additional rules of constraints into the runtime when several parameters have dependencies due to hardware design.
The driver can refers to result of the interaction in a callback of
struct snd_pcm_ops.hw_params, however it should not change the
Tracepoints in this category are designed to trace changes of the
mask/interval parameters. When ALSA PCM core changes them,
hw_interval_param event is probed according to type of the changed parameter.
ALSA PCM core also has a pretty print format for each of the tracepoints. Below
is an example for
hw_mask_param: pcmC0D0p 001/023 FORMAT 00000000000000000000001000000044 00000000000000000000001000000044
Below is an example for
hw_interval_param: pcmC0D0p 000/023 BUFFER_SIZE 0 0 [0 4294967295] 0 1 [0 4294967295]
The first three fields are common. They represent name of ALSA PCM character device, rules of constraint and name of the changed parameter, in order. The field for rules of constraint consists of two sub-fields; index of applied rule and total number of rules added to the runtime. As an exception, the index 000 means that the parameter is changed by ALSA PCM core, regardless of the rules.
The rest of field represent state of the parameter before/after changing. These
fields are different according to type of the parameter. For parameters of mask
type, the fields represent hexadecimal dump of content of the parameter. For
parameters of interval type, the fields represent values of each member of
struct snd_interval in this order.
Tracepoints in drivers¶
Some drivers have tracepoints for developers’ convenience. For them, please refer to each documentation or implementation.