Linux kernel SLIMbus support

Overview

What is SLIMbus?

SLIMbus (Serial Low Power Interchip Media Bus) is a specification developed by MIPI (Mobile Industry Processor Interface) alliance. The bus uses master/slave configuration, and is a 2-wire multi-drop implementation (clock, and data).

Currently, SLIMbus is used to interface between application processors of SoCs (System-on-Chip) and peripheral components (typically codec). SLIMbus uses Time-Division-Multiplexing to accommodate multiple data channels, and a control channel.

The control channel is used for various control functions such as bus management, configuration and status updates. These messages can be unicast (e.g. reading/writing device specific values), or multicast (e.g. data channel reconfiguration sequence is a broadcast message announced to all devices)

A data channel is used for data-transfer between 2 SLIMbus devices. Data channel uses dedicated ports on the device.

Hardware description:

SLIMbus specification has different types of device classifications based on their capabilities. A manager device is responsible for enumeration, configuration, and dynamic channel allocation. Every bus has 1 active manager.

A generic device is a device providing application functionality (e.g. codec).

Framer device is responsible for clocking the bus, and transmitting frame-sync and framing information on the bus.

Each SLIMbus component has an interface device for monitoring physical layer.

Typically each SoC contains SLIMbus component having 1 manager, 1 framer device, 1 generic device (for data channel support), and 1 interface device. External peripheral SLIMbus component usually has 1 generic device (for functionality/data channel support), and an associated interface device. The generic device’s registers are mapped as ‘value elements’ so that they can be written/read using SLIMbus control channel exchanging control/status type of information. In case there are multiple framer devices on the same bus, manager device is responsible to select the active-framer for clocking the bus.

Per specification, SLIMbus uses “clock gears” to do power management based on current frequency and bandwidth requirements. There are 10 clock gears and each gear changes the SLIMbus frequency to be twice its previous gear.

Each device has a 6-byte enumeration-address and the manager assigns every device with a 1-byte logical address after the devices report presence on the bus.

Software description:

There are 2 types of SLIMbus drivers:

slim_controller represents a ‘controller’ for SLIMbus. This driver should implement duties needed by the SoC (manager device, associated interface device for monitoring the layers and reporting errors, default framer device).

slim_device represents the ‘generic device/component’ for SLIMbus, and a slim_driver should implement driver for that slim_device.

Device notifications to the driver:

Since SLIMbus devices have mechanisms for reporting their presence, the framework allows drivers to bind when corresponding devices report their presence on the bus. However, it is possible that the driver needs to be probed first so that it can enable corresponding SLIMbus device (e.g. power it up and/or take it out of reset). To support that behavior, the framework allows drivers to probe first as well (e.g. using standard DeviceTree compatibility field). This creates the necessity for the driver to know when the device is functional (i.e. reported present). device_up callback is used for that reason when the device reports present and is assigned a logical address by the controller.

Similarly, SLIMbus devices ‘report absent’ when they go down. A ‘device_down’ callback notifies the driver when the device reports absent and its logical address assignment is invalidated by the controller.

Another notification “boot_device” is used to notify the slim_driver when controller resets the bus. This notification allows the driver to take necessary steps to boot the device so that it’s functional after the bus has been reset.

Driver and Controller APIs:

struct slim_eaddr

Enumeration address for a SLIMbus device

Definition

struct slim_eaddr {
  u8 instance;
  u8 dev_index;
  u16 prod_code;
  u16 manf_id;
};

Members

instance

Instance value

dev_index

Device index

prod_code

Product code

manf_id

Manufacturer Id for the device

enum slim_device_status

slim device status

Constants

SLIM_DEVICE_STATUS_DOWN

Slim device is absent or not reported yet.

SLIM_DEVICE_STATUS_UP

Slim device is announced on the bus.

SLIM_DEVICE_STATUS_RESERVED

Reserved for future use.

struct slim_device

Slim device handle.

Definition

struct slim_device {
  struct device           dev;
  struct slim_eaddr       e_addr;
  struct slim_controller  *ctrl;
  enum slim_device_status status;
  u8 laddr;
  bool is_laddr_valid;
  struct list_head        stream_list;
  spinlock_t stream_list_lock;
};

Members

dev

Driver model representation of the device.

e_addr

Enumeration address of this device.

ctrl

slim controller instance.

status

slim device status

laddr

1-byte Logical address of this device.

is_laddr_valid

indicates if the laddr is valid or not

stream_list

List of streams on this device

stream_list_lock

lock to protect the stream list

Description

This is the client/device handle returned when a SLIMbus device is registered with a controller. Pointer to this structure is used by client-driver as a handle.

struct slim_driver

SLIMbus ‘generic device’ (slave) device driver (similar to ‘spi_device’ on SPI)

Definition

struct slim_driver {
  int (*probe)(struct slim_device *sl);
  void (*remove)(struct slim_device *sl);
  void (*shutdown)(struct slim_device *sl);
  int (*device_status)(struct slim_device *sl, enum slim_device_status s);
  struct device_driver            driver;
  const struct slim_device_id     *id_table;
};

Members

probe

Binds this driver to a SLIMbus device.

remove

Unbinds this driver from the SLIMbus device.

shutdown

Standard shutdown callback used during powerdown/halt.

device_status

This callback is called when - The device reports present and gets a laddr assigned - The device reports absent, or the bus goes down.

driver

SLIMbus device drivers should initialize name and owner field of this structure

id_table

List of SLIMbus devices supported by this driver

struct slim_val_inf

Slimbus value or information element

Definition

struct slim_val_inf {
  u16 start_offset;
  u8 num_bytes;
  u8 *rbuf;
  const u8                *wbuf;
  struct completion      *comp;
};

Members

start_offset

Specifies starting offset in information/value element map

num_bytes

upto 16. This ensures that the message will fit the slicesize per SLIMbus spec

rbuf

buffer to read the values

wbuf

buffer to write

comp

completion for asynchronous operations, valid only if TID is required for transaction, like REQUEST operations. Rest of the transactions are synchronous anyway.

struct slim_stream_config

SLIMbus stream configuration Configuring a stream is done at hw_params or prepare call from audio drivers where they have all the required information regarding rate, number of channels and so on. There is a 1:1 mapping of channel and ports.

Definition

struct slim_stream_config {
  unsigned int rate;
  unsigned int bps;
  unsigned int ch_count;
  unsigned int *chs;
  unsigned long port_mask;
  int direction;
};

Members

rate

data rate

bps

bits per data sample

ch_count

number of channels

chs

pointer to list of channel numbers

port_mask

port mask of ports to use for this stream

direction

direction of the stream, SNDRV_PCM_STREAM_PLAYBACK or SNDRV_PCM_STREAM_CAPTURE.

module_slim_driver

module_slim_driver (__slim_driver)

Helper macro for registering a SLIMbus driver

Parameters

__slim_driver

slimbus_driver struct

Description

Helper macro for SLIMbus drivers which do not do anything special in module init/exit. This eliminates a lot of boilerplate. Each module may only use this macro once, and calling it replaces module_init() and module_exit()

struct slim_framer

Represents SLIMbus framer. Every controller may have multiple framers. There is 1 active framer device responsible for clocking the bus. Manager is responsible for framer hand-over.

Definition

struct slim_framer {
  struct device           dev;
  struct slim_eaddr       e_addr;
  int rootfreq;
  int superfreq;
};

Members

dev

Driver model representation of the device.

e_addr

Enumeration address of the framer.

rootfreq

Root Frequency at which the framer can run. This is maximum frequency (‘clock gear 10’) at which the bus can operate.

superfreq

Superframes per root frequency. Every frame is 6144 bits.

struct slim_msg_txn

Message to be sent by the controller. This structure has packet header, payload and buffer to be filled (if any)

Definition

struct slim_msg_txn {
  u8 rl;
  u8 mt;
  u8 mc;
  u8 dt;
  u16 ec;
  u8 tid;
  u8 la;
  struct slim_val_inf     *msg;
  struct completion      *comp;
};

Members

rl

Header field. remaining length.

mt

Header field. Message type.

mc

Header field. LSB is message code for type mt.

dt

Header field. Destination type.

ec

Element code. Used for elemental access APIs.

tid

Transaction ID. Used for messages expecting response. (relevant for message-codes involving read operation)

la

Logical address of the device this message is going to. (Not used when destination type is broadcast.)

msg

Elemental access message to be read/written

comp

completion if read/write is synchronous, used internally for tid based transactions.

enum slim_clk_state

SLIMbus controller’s clock state used internally for maintaining current clock state.

Constants

SLIM_CLK_ACTIVE

SLIMbus clock is active

SLIM_CLK_ENTERING_PAUSE

SLIMbus clock pause sequence is being sent on the bus. If this succeeds, state changes to SLIM_CLK_PAUSED. If the transition fails, state changes back to SLIM_CLK_ACTIVE

SLIM_CLK_PAUSED

SLIMbus controller clock has paused.

struct slim_sched

Framework uses this structure internally for scheduling.

Definition

struct slim_sched {
  enum slim_clk_state     clk_state;
  struct completion       pause_comp;
  struct mutex            m_reconf;
};

Members

clk_state

Controller’s clock state from enum slim_clk_state

pause_comp

Signals completion of clock pause sequence. This is useful when client tries to call SLIMbus transaction when controller is entering clock pause.

m_reconf

This mutex is held until current reconfiguration (data channel scheduling, message bandwidth reservation) is done. Message APIs can use the bus concurrently when this mutex is held since elemental access messages can be sent on the bus when reconfiguration is in progress.

enum slim_port_direction

SLIMbus port direction

Constants

SLIM_PORT_SINK

SLIMbus port is a sink

SLIM_PORT_SOURCE

SLIMbus port is a source

enum slim_port_state

SLIMbus Port/Endpoint state machine according to SLIMbus Spec 2.0

Constants

SLIM_PORT_DISCONNECTED

SLIMbus port is disconnected entered from Unconfigure/configured state after DISCONNECT_PORT or REMOVE_CHANNEL core command

SLIM_PORT_UNCONFIGURED

SLIMbus port is in unconfigured state. entered from disconnect state after CONNECT_SOURCE/SINK core command

SLIM_PORT_CONFIGURED

SLIMbus port is in configured state. entered from unconfigured state after DEFINE_CHANNEL, DEFINE_CONTENT and ACTIVATE_CHANNEL core commands. Ready for data transmission.

enum slim_channel_state

SLIMbus channel state machine used by core.

Constants

SLIM_CH_STATE_DISCONNECTED

SLIMbus channel is disconnected

SLIM_CH_STATE_ALLOCATED

SLIMbus channel is allocated

SLIM_CH_STATE_ASSOCIATED

SLIMbus channel is associated with port

SLIM_CH_STATE_DEFINED

SLIMbus channel parameters are defined

SLIM_CH_STATE_CONTENT_DEFINED

SLIMbus channel content is defined

SLIM_CH_STATE_ACTIVE

SLIMbus channel is active and ready for data

SLIM_CH_STATE_REMOVED

SLIMbus channel is inactive and removed

enum slim_ch_data_fmt

SLIMbus channel data Type identifiers according to Table 60 of SLIMbus Spec 1.01.01

Constants

SLIM_CH_DATA_FMT_NOT_DEFINED

Undefined

SLIM_CH_DATA_FMT_LPCM_AUDIO

LPCM audio

SLIM_CH_DATA_FMT_IEC61937_COMP_AUDIO

IEC61937 Compressed audio

SLIM_CH_DATA_FMT_PACKED_PDM_AUDIO

Packed PDM audio

enum slim_ch_aux_bit_fmt

SLIMbus channel Aux Field format IDs according to Table 63 of SLIMbus Spec 2.0

Constants

SLIM_CH_AUX_FMT_NOT_APPLICABLE

Undefined

SLIM_CH_AUX_FMT_ZCUV_TUNNEL_IEC60958

ZCUV for tunneling IEC60958

SLIM_CH_AUX_FMT_USER_DEFINED

User defined

struct slim_channel

SLIMbus channel, used for state machine

Definition

struct slim_channel {
  int id;
  int prrate;
  int seg_dist;
  enum slim_ch_data_fmt data_fmt;
  enum slim_ch_aux_bit_fmt aux_fmt;
  enum slim_channel_state state;
};

Members

id

ID of channel

prrate

Presense rate of channel from Table 66 of SLIMbus 2.0 Specs

seg_dist

segment distribution code from Table 20 of SLIMbus 2.0 Specs

data_fmt

Data format of channel.

aux_fmt

Aux format for this channel.

state

channel state machine

struct slim_port

SLIMbus port

Definition

struct slim_port {
  int id;
  enum slim_port_direction direction;
  enum slim_port_state state;
  struct slim_channel ch;
};

Members

id

Port id

direction

Port direction, Source or Sink.

state

state machine of port.

ch

channel associated with this port.

enum slim_transport_protocol

SLIMbus Transport protocol list from Table 47 of SLIMbus 2.0 specs.

Constants

SLIM_PROTO_ISO

Isochronous Protocol, no flow control as data rate match channel rate flow control embedded in the data.

SLIM_PROTO_PUSH

Pushed Protocol, includes flow control, Used to carry data whose rate is equal to, or lower than the channel rate.

SLIM_PROTO_PULL

Pulled Protocol, similar usage as pushed protocol but pull is a unicast.

SLIM_PROTO_LOCKED

Locked Protocol

SLIM_PROTO_ASYNC_SMPLX

Asynchronous Protocol-Simplex

SLIM_PROTO_ASYNC_HALF_DUP

Asynchronous Protocol-Half-duplex

SLIM_PROTO_EXT_SMPLX

Extended Asynchronous Protocol-Simplex

SLIM_PROTO_EXT_HALF_DUP

Extended Asynchronous Protocol-Half-duplex

struct slim_stream_runtime

SLIMbus stream runtime instance

Definition

struct slim_stream_runtime {
  const char *name;
  struct slim_device *dev;
  int direction;
  enum slim_transport_protocol prot;
  unsigned int rate;
  unsigned int bps;
  unsigned int ratem;
  int num_ports;
  struct slim_port *ports;
  struct list_head node;
};

Members

name

Name of the stream

dev

SLIM Device instance associated with this stream

direction

direction of stream

prot

Transport protocol used in this stream

rate

Data rate of samples *

bps

bits per sample

ratem

rate multipler which is super frame rate/data rate

num_ports

number of ports

ports

pointer to instance of ports

node

list head for stream associated with slim device.

struct slim_controller

Controls every instance of SLIMbus (similar to ‘master’ on SPI)

Definition

struct slim_controller {
  struct device           *dev;
  unsigned int            id;
  char name[SLIMBUS_NAME_SIZE];
  int min_cg;
  int max_cg;
  int clkgear;
  struct ida              laddr_ida;
  struct slim_framer      *a_framer;
  struct mutex            lock;
  struct list_head        devices;
  struct idr              tid_idr;
  spinlock_t txn_lock;
  struct slim_sched       sched;
  int (*xfer_msg)(struct slim_controller *ctrl, struct slim_msg_txn *tx);
  int (*set_laddr)(struct slim_controller *ctrl, struct slim_eaddr *ea, u8 laddr);
  int (*get_laddr)(struct slim_controller *ctrl, struct slim_eaddr *ea, u8 *laddr);
  int (*enable_stream)(struct slim_stream_runtime *rt);
  int (*disable_stream)(struct slim_stream_runtime *rt);
  int (*wakeup)(struct slim_controller *ctrl);
};

Members

dev

Device interface to this driver

id

Board-specific number identifier for this controller/bus

name

Name for this controller

min_cg

Minimum clock gear supported by this controller (default value: 1)

max_cg

Maximum clock gear supported by this controller (default value: 10)

clkgear

Current clock gear in which this bus is running

laddr_ida

logical address id allocator

a_framer

Active framer which is clocking the bus managed by this controller

lock

Mutex protecting controller data structures

devices

Slim device list

tid_idr

tid id allocator

txn_lock

Lock to protect table of transactions

sched

scheduler structure used by the controller

xfer_msg

Transfer a message on this controller (this can be a broadcast control/status message like data channel setup, or a unicast message like value element read/write.

set_laddr

Setup logical address at laddr for the slave with elemental address e_addr. Drivers implementing controller will be expected to send unicast message to this device with its logical address.

get_laddr

It is possible that controller needs to set fixed logical address table and get_laddr can be used in that case so that controller can do this assignment. Use case is when the master is on the remote processor side, who is resposible for allocating laddr.

enable_stream

This function pointer implements controller-specific procedure to enable a stream.

disable_stream

This function pointer implements controller-specific procedure to disable stream.

‘Manager device’ is responsible for device management, bandwidth allocation, channel setup, and port associations per channel. Device management means Logical address assignment/removal based on enumeration (report-present, report-absent) of a device. Bandwidth allocation is done dynamically by the manager based on active channels on the bus, message-bandwidth requests made by SLIMbus devices. Based on current bandwidth usage, manager chooses a frequency to run the bus at (in steps of ‘clock-gear’, 1 through 10, each clock gear representing twice the frequency than the previous gear). Manager is also responsible for entering (and exiting) low-power-mode (known as ‘clock pause’). Manager can do handover of framer if there are multiple framers on the bus and a certain usecase warrants using certain framer to avoid keeping previous framer being powered-on.

Controller here performs duties of the manager device, and ‘interface device’. Interface device is responsible for monitoring the bus and reporting information such as loss-of-synchronization, data slot-collision.

wakeup

This function pointer implements controller-specific procedure to wake it up from clock-pause. Framework will call this to bring the controller out of clock pause.

int slim_unregister_controller(struct slim_controller *ctrl)

Controller tear-down.

Parameters

struct slim_controller *ctrl

Controller to tear-down.

void slim_report_absent(struct slim_device *sbdev)

Controller calls this function when a device reports absent, OR when the device cannot be communicated with

Parameters

struct slim_device *sbdev

Device that cannot be reached, or sent report absent

struct slim_device *slim_get_device(struct slim_controller *ctrl, struct slim_eaddr *e_addr)

get handle to a device.

Parameters

struct slim_controller *ctrl

Controller on which this device will be added/queried

struct slim_eaddr *e_addr

Enumeration address of the device to be queried

Return

pointer to a device if it has already reported. Creates a new device and returns pointer to it if the device has not yet enumerated.

struct slim_device *of_slim_get_device(struct slim_controller *ctrl, struct device_node *np)

get handle to a device using dt node.

Parameters

struct slim_controller *ctrl

Controller on which this device will be added/queried

struct device_node *np

node pointer to device

Return

pointer to a device if it has already reported. Creates a new device and returns pointer to it if the device has not yet enumerated.

int slim_device_report_present(struct slim_controller *ctrl, struct slim_eaddr *e_addr, u8 *laddr)

Report enumerated device.

Parameters

struct slim_controller *ctrl

Controller with which device is enumerated.

struct slim_eaddr *e_addr

Enumeration address of the device.

u8 *laddr

Return logical address (if valid flag is false)

Description

Called by controller in response to REPORT_PRESENT. Framework will assign a logical address to this enumeration address. Function returns -EXFULL to indicate that all logical addresses are already taken.

int slim_get_logical_addr(struct slim_device *sbdev)

get/allocate logical address of a SLIMbus device.

Parameters

struct slim_device *sbdev

client handle requesting the address.

Return

zero if a logical address is valid or a new logical address has been assigned. error code in case of error.

Clock-pause:

SLIMbus mandates that a reconfiguration sequence (known as clock-pause) be broadcast to all active devices on the bus before the bus can enter low-power mode. Controller uses this sequence when it decides to enter low-power mode so that corresponding clocks and/or power-rails can be turned off to save power. Clock-pause is exited by waking up framer device (if controller driver initiates exiting low power mode), or by toggling the data line (if a slave device wants to initiate it).

Clock-pause APIs:

int slim_ctrl_clk_pause(struct slim_controller *ctrl, bool wakeup, u8 restart)

Called by slimbus controller to enter/exit ‘clock pause’

Parameters

struct slim_controller *ctrl

controller requesting bus to be paused or woken up

bool wakeup

Wakeup this controller from clock pause.

u8 restart

Restart time value per spec used for clock pause. This value isn’t used when controller is to be woken up.

Description

Slimbus specification needs this sequence to turn-off clocks for the bus. The sequence involves sending 3 broadcast messages (reconfiguration sequence) to inform all devices on the bus. To exit clock-pause, controller typically wakes up active framer device. This API executes clock pause reconfiguration sequence if wakeup is false. If wakeup is true, controller’s wakeup is called. For entering clock-pause, -EBUSY is returned if a message txn in pending.

Messaging:

The framework supports regmap and read/write apis to exchange control-information with a SLIMbus device. APIs can be synchronous or asynchronous. The header file <linux/slimbus.h> has more documentation about messaging APIs.

Messaging APIs:

void slim_msg_response(struct slim_controller *ctrl, u8 *reply, u8 tid, u8 len)

Deliver Message response received from a device to the framework.

Parameters

struct slim_controller *ctrl

Controller handle

u8 *reply

Reply received from the device

u8 tid

Transaction ID received with which framework can associate reply.

u8 len

Length of the reply

Description

Called by controller to inform framework about the response received. This helps in making the API asynchronous, and controller-driver doesn’t need to manage 1 more table other than the one managed by framework mapping TID with buffers

int slim_alloc_txn_tid(struct slim_controller *ctrl, struct slim_msg_txn *txn)

Allocate a tid to txn

Parameters

struct slim_controller *ctrl

Controller handle

struct slim_msg_txn *txn

transaction to be allocated with tid.

Return

zero on success with valid txn->tid and error code on failures.

void slim_free_txn_tid(struct slim_controller *ctrl, struct slim_msg_txn *txn)

Freee tid of txn

Parameters

struct slim_controller *ctrl

Controller handle

struct slim_msg_txn *txn

transaction whose tid should be freed

int slim_do_transfer(struct slim_controller *ctrl, struct slim_msg_txn *txn)

Process a SLIMbus-messaging transaction

Parameters

struct slim_controller *ctrl

Controller handle

struct slim_msg_txn *txn

Transaction to be sent over SLIMbus

Description

Called by controller to transmit messaging transactions not dealing with Interface/Value elements. (e.g. transmittting a message to assign logical address to a slave device

Return

-ETIMEDOUT: If transmission of this message timed out

(e.g. due to bus lines not being clocked or driven by controller)

int slim_xfer_msg(struct slim_device *sbdev, struct slim_val_inf *msg, u8 mc)

Transfer a value info message on slim device

Parameters

struct slim_device *sbdev

slim device to which this msg has to be transfered

struct slim_val_inf *msg

value info message pointer

u8 mc

message code of the message

Description

Called by drivers which want to transfer a vlaue or info elements.

Return

-ETIMEDOUT: If transmission of this message timed out

int slim_read(struct slim_device *sdev, u32 addr, size_t count, u8 *val)

Read SLIMbus value element

Parameters

struct slim_device *sdev

client handle.

u32 addr

address of value element to read.

size_t count

number of bytes to read. Maximum bytes allowed are 16.

u8 *val

will return what the value element value was

Return

-EINVAL for Invalid parameters, -ETIMEDOUT If transmission of this message timed out (e.g. due to bus lines not being clocked or driven by controller)

int slim_readb(struct slim_device *sdev, u32 addr)

Read byte from SLIMbus value element

Parameters

struct slim_device *sdev

client handle.

u32 addr

address in the value element to read.

Return

byte value of value element.

int slim_write(struct slim_device *sdev, u32 addr, size_t count, u8 *val)

Write SLIMbus value element

Parameters

struct slim_device *sdev

client handle.

u32 addr

address in the value element to write.

size_t count

number of bytes to write. Maximum bytes allowed are 16.

u8 *val

value to write to value element

Return

-EINVAL for Invalid parameters, -ETIMEDOUT If transmission of this message timed out (e.g. due to bus lines not being clocked or driven by controller)

int slim_writeb(struct slim_device *sdev, u32 addr, u8 value)

Write byte to SLIMbus value element

Parameters

struct slim_device *sdev

client handle.

u32 addr

address of value element to write.

u8 value

value to write to value element

Return

-EINVAL for Invalid parameters, -ETIMEDOUT If transmission of this message timed out (e.g. due to bus lines not being clocked or driven by controller)

Streaming APIs:

struct slim_stream_runtime *slim_stream_allocate(struct slim_device *dev, const char *name)

Allocate a new SLIMbus Stream

Parameters

struct slim_device *dev

Slim device to be associated with

const char *name

name of the stream

Description

This is very first call for SLIMbus streaming, this API will allocate a new SLIMbus stream and return a valid stream runtime pointer for client to use it in subsequent stream apis. state of stream is set to ALLOCATED

Return

valid pointer on success and error code on failure. From ASoC DPCM framework, this state is linked to startup() operation.

int slim_stream_prepare(struct slim_stream_runtime *rt, struct slim_stream_config *cfg)

Prepare a SLIMbus Stream

Parameters

struct slim_stream_runtime *rt

instance of slim stream runtime to configure

struct slim_stream_config *cfg

new configuration for the stream

Description

This API will configure SLIMbus stream with config parameters from cfg. return zero on success and error code on failure. From ASoC DPCM framework, this state is linked to hw_params() operation.

int slim_stream_enable(struct slim_stream_runtime *stream)

Enable a prepared SLIMbus Stream

Parameters

struct slim_stream_runtime *stream

instance of slim stream runtime to enable

Description

This API will enable all the ports and channels associated with SLIMbus stream

Return

zero on success and error code on failure. From ASoC DPCM framework, this state is linked to trigger() start operation.

int slim_stream_disable(struct slim_stream_runtime *stream)

Disable a SLIMbus Stream

Parameters

struct slim_stream_runtime *stream

instance of slim stream runtime to disable

Description

This API will disable all the ports and channels associated with SLIMbus stream

Return

zero on success and error code on failure. From ASoC DPCM framework, this state is linked to trigger() pause operation.

int slim_stream_unprepare(struct slim_stream_runtime *stream)

Un-prepare a SLIMbus Stream

Parameters

struct slim_stream_runtime *stream

instance of slim stream runtime to unprepare

Description

This API will un allocate all the ports and channels associated with SLIMbus stream

Return

zero on success and error code on failure. From ASoC DPCM framework, this state is linked to trigger() stop operation.

int slim_stream_free(struct slim_stream_runtime *stream)

Free a SLIMbus Stream

Parameters

struct slim_stream_runtime *stream

instance of slim stream runtime to free

Description

This API will un allocate all the memory associated with slim stream runtime, user is not allowed to make an dereference to stream after this call.

Return

zero on success and error code on failure. From ASoC DPCM framework, this state is linked to shutdown() operation.