7.37. ioctl VIDIOC_G_PARM, VIDIOC_S_PARM

7.37.1. Name

VIDIOC_G_PARM - VIDIOC_S_PARM - Get or set streaming parameters

7.37.2. Synopsis

VIDIOC_G_PARM

int ioctl(int fd, VIDIOC_G_PARM, v4l2_streamparm *argp)

VIDIOC_S_PARM

int ioctl(int fd, VIDIOC_S_PARM, v4l2_streamparm *argp)

7.37.3. Arguments

fd

File descriptor returned by open().

argp

Pointer to struct v4l2_streamparm.

7.37.4. Description

Applications can request a different frame interval. The capture or output device will be reconfigured to support the requested frame interval if possible. Optionally drivers may choose to skip or repeat frames to achieve the requested frame interval.

For stateful encoders (see Memory-to-Memory Stateful Video Encoder Interface) this represents the frame interval that is typically embedded in the encoded video stream.

Changing the frame interval shall never change the format. Changing the format, on the other hand, may change the frame interval.

Further these ioctls can be used to determine the number of buffers used internally by a driver in read/write mode. For implications see the section discussing the read() function.

To get and set the streaming parameters applications call the VIDIOC_G_PARM and VIDIOC_S_PARM ioctl, respectively. They take a pointer to a struct v4l2_streamparm which contains a union holding separate parameters for input and output devices.

v4l2_streamparm
struct v4l2_streamparm

__u32

type

The buffer (stream) type, same as struct v4l2_format type, set by the application. See v4l2_buf_type.

union {

parm

struct v4l2_captureparm

capture

Parameters for capture devices, used when type is V4L2_BUF_TYPE_VIDEO_CAPTURE or V4L2_BUF_TYPE_VIDEO_CAPTURE_MPLANE.

struct v4l2_outputparm

output

Parameters for output devices, used when type is V4L2_BUF_TYPE_VIDEO_OUTPUT or V4L2_BUF_TYPE_VIDEO_OUTPUT_MPLANE.

__u8

raw_data[200]

A place holder for future extensions.

}

v4l2_captureparm
struct v4l2_captureparm

__u32

capability

See Streaming Parameters Capabilities.

__u32

capturemode

Set by drivers and applications, see Capture Parameters Flags.

struct v4l2_fract

timeperframe

This is the desired period between successive frames captured by the driver, in seconds.

This will configure the speed at which the video source (e.g. a sensor) generates video frames. If the speed is fixed, then the driver may choose to skip or repeat frames in order to achieve the requested frame rate.

For stateful encoders (see Memory-to-Memory Stateful Video Encoder Interface) this represents the frame interval that is typically embedded in the encoded video stream.

Applications store here the desired frame period, drivers return the actual frame period.

Changing the video standard (also implicitly by switching the video input) may reset this parameter to the nominal frame period. To reset manually applications can just set this field to zero.

Drivers support this function only when they set the V4L2_CAP_TIMEPERFRAME flag in the capability field.

__u32

extendedmode

Custom (driver specific) streaming parameters. When unused, applications and drivers must set this field to zero. Applications using this field should check the driver name and version, see Querying Capabilities.

__u32

readbuffers

Applications set this field to the desired number of buffers used internally by the driver in read() mode. Drivers return the actual number of buffers. When an application requests zero buffers, drivers should just return the current setting rather than the minimum or an error code. For details see Read/Write.

__u32

reserved[4]

Reserved for future extensions. Drivers and applications must set the array to zero.

v4l2_outputparm
struct v4l2_outputparm

__u32

capability

See Streaming Parameters Capabilities.

__u32

outputmode

Set by drivers and applications, see Capture Parameters Flags.

struct v4l2_fract

timeperframe

This is the desired period between successive frames output by the driver, in seconds.

The field is intended to repeat frames on the driver side in write() mode (in streaming mode timestamps can be used to throttle the output), saving I/O bandwidth.

For stateful encoders (see Memory-to-Memory Stateful Video Encoder Interface) this represents the frame interval that is typically embedded in the encoded video stream and it provides a hint to the encoder of the speed at which raw frames are queued up to the encoder.

Applications store here the desired frame period, drivers return the actual frame period.

Changing the video standard (also implicitly by switching the video output) may reset this parameter to the nominal frame period. To reset manually applications can just set this field to zero.

Drivers support this function only when they set the V4L2_CAP_TIMEPERFRAME flag in the capability field.

__u32

extendedmode

Custom (driver specific) streaming parameters. When unused, applications and drivers must set this field to zero. Applications using this field should check the driver name and version, see Querying Capabilities.

__u32

writebuffers

Applications set this field to the desired number of buffers used internally by the driver in write() mode. Drivers return the actual number of buffers. When an application requests zero buffers, drivers should just return the current setting rather than the minimum or an error code. For details see Read/Write.

__u32

reserved[4]

Reserved for future extensions. Drivers and applications must set the array to zero.

Streaming Parameters Capabilities

V4L2_CAP_TIMEPERFRAME

0x1000

The frame period can be modified by setting the timeperframe field.

Capture Parameters Flags

V4L2_MODE_HIGHQUALITY

0x0001

High quality imaging mode. High quality mode is intended for still imaging applications. The idea is to get the best possible image quality that the hardware can deliver. It is not defined how the driver writer may achieve that; it will depend on the hardware and the ingenuity of the driver writer. High quality mode is a different mode from the regular motion video capture modes. In high quality mode:

  • The driver may be able to capture higher resolutions than for motion capture.

  • The driver may support fewer pixel formats than motion capture (eg; true color).

  • The driver may capture and arithmetically combine multiple successive fields or frames to remove color edge artifacts and reduce the noise in the video data.

  • The driver may capture images in slices like a scanner in order to handle larger format images than would otherwise be possible.

  • An image capture operation may be significantly slower than motion capture.

  • Moving objects in the image might have excessive motion blur.

  • Capture might only work through the read() call.

7.37.5. Return Value

On success 0 is returned, on error -1 and the errno variable is set appropriately. The generic error codes are described at the Generic Error Codes chapter.