Anju T Sudhakar, 10 May 2019
IMC (In-Memory collection counters) is a hardware monitoring facility that collects large numbers of hardware performance events at Nest level (these are on-chip but off-core), Core level and Thread level.
The Nest PMU counters are handled by a Nest IMC microcode which runs in the OCC (On-Chip Controller) complex. The microcode collects the counter data and moves the nest IMC counter data to memory.
The Core and Thread IMC PMU counters are handled in the core. Core level PMU counters give us the IMC counters’ data per core and thread level PMU counters give us the IMC counters’ data per CPU thread.
OPAL obtains the IMC PMU and supported events information from the IMC Catalog and passes on to the kernel via the device tree. The event’s information contains:
and possibly also:
Some PMUs may have a common scale and unit values for all their supported events. For those cases, the scale and unit properties for those events must be inherited from the PMU.
The event offset in the memory is where the counter data gets accumulated.
- IMC catalog is available at:
The kernel discovers the IMC counters information in the device tree at the imc-counters device node which has a compatible field ibm,opal-in-memory-counters. From the device tree, the kernel parses the PMUs and their event’s information and register the PMU and its attributes in the kernel.
# perf list [...] nest_mcs01/PM_MCS01_64B_RD_DISP_PORT01/ [Kernel PMU event] nest_mcs01/PM_MCS01_64B_RD_DISP_PORT23/ [Kernel PMU event] [...] core_imc/CPM_0THRD_NON_IDLE_PCYC/ [Kernel PMU event] core_imc/CPM_1THRD_NON_IDLE_INST/ [Kernel PMU event] [...] thread_imc/CPM_0THRD_NON_IDLE_PCYC/ [Kernel PMU event] thread_imc/CPM_1THRD_NON_IDLE_INST/ [Kernel PMU event]
To see per chip data for nest_mcs0/PM_MCS_DOWN_128B_DATA_XFER_MC0/:
# ./perf stat -e "nest_mcs01/PM_MCS01_64B_WR_DISP_PORT01/" -a --per-socket
To see non-idle instructions for core 0:
# ./perf stat -e "core_imc/CPM_NON_IDLE_INST/" -C 0 -I 1000
To see non-idle instructions for a “make”:
# ./perf stat -e "thread_imc/CPM_NON_IDLE_PCYC/" make
POWER9 supports two modes for IMC which are the Accumulation mode and Trace mode. In Accumulation mode, event counts are accumulated in system Memory. Hypervisor then reads the posted counts periodically or when requested. In IMC Trace mode, the 64 bit trace SCOM value is initialized with the event information. The CPMCxSEL and CPMC_LOAD in the trace SCOM, specifies the event to be monitored and the sampling duration. On each overflow in the CPMCxSEL, hardware snapshots the program counter along with event counts and writes into memory pointed by LDBAR.
LDBAR is a 64 bit special purpose per thread register, it has bits to indicate whether hardware is configured for accumulation or trace mode.
0: Accumulation Mode
1: Trace Mode
CPMC_LOAD contains the sampling duration. SAMPSEL and CPMCxSEL determines the event to count. BUFFERSIZE indicates the memory range. On each overflow, hardware snapshots the program counter along with event counts and updates the memory and reloads the CMPC_LOAD value for the next sampling duration. IMC hardware does not support exceptions, so it quietly wraps around if memory buffer reaches the end.
Currently the event monitored for trace-mode is fixed as cycle.
# perf list [....] trace_imc/trace_cycles/ [Kernel PMU event]
To record an application/process with trace-imc event:
# perf record -e trace_imc/trace_cycles/ yes > /dev/null [ perf record: Woken up 1 times to write data ] [ perf record: Captured and wrote 0.012 MB perf.data (21 samples) ]
The perf.data generated, can be read using perf report.
PMI (Performance Monitoring Interrupts) interrupt handling is avoided, since IMC trace mode snapshots the program counter and updates to the memory. And this also provide a way for the operating system to do instruction sampling in real time without PMI processing overhead.
Performance data using perf top with and without trace-imc event.
PMI interrupts count when perf top command is executed without trace-imc event.
# grep PMI /proc/interrupts PMI: 0 0 0 0 Performance monitoring interrupts # ./perf top ... # grep PMI /proc/interrupts PMI: 39735 8710 17338 17801 Performance monitoring interrupts # ./perf top -e trace_imc/trace_cycles/ ... # grep PMI /proc/interrupts PMI: 39735 8710 17338 17801 Performance monitoring interrupts
That is, the PMI interrupt counts do not increment when using the trace_imc event.