VGA Arbiter

Graphic devices are accessed through ranges in I/O or memory space. While most modern devices allow relocation of such ranges, some “Legacy” VGA devices implemented on PCI will typically have the same “hard-decoded” addresses as they did on ISA. For more details see “PCI Bus Binding to IEEE Std 1275-1994 Standard for Boot (Initialization Configuration) Firmware Revision 2.1” Section 7, Legacy Devices.

The Resource Access Control (RAC) module inside the X server [0] existed for the legacy VGA arbitration task (besides other bus management tasks) when more than one legacy device co-exists on the same machine. But the problem happens when these devices are trying to be accessed by different userspace clients (e.g. two server in parallel). Their address assignments conflict. Moreover, ideally, being a userspace application, it is not the role of the X server to control bus resources. Therefore an arbitration scheme outside of the X server is needed to control the sharing of these resources. This document introduces the operation of the VGA arbiter implemented for the Linux kernel.

vgaarb kernel/userspace ABI

The vgaarb is a module of the Linux Kernel. When it is initially loaded, it scans all PCI devices and adds the VGA ones inside the arbitration. The arbiter then enables/disables the decoding on different devices of the VGA legacy instructions. Devices which do not want/need to use the arbiter may explicitly tell it by calling vga_set_legacy_decoding().

The kernel exports a char device interface (/dev/vga_arbiter) to the clients, which has the following semantics:

open

Opens a user instance of the arbiter. By default, it’s attached to the default VGA device of the system.

close

Close a user instance. Release locks made by the user

read

Return a string indicating the status of the target like:

“<card_ID>,decodes=<io_state>,owns=<io_state>,locks=<io_state> (ic,mc)”

An IO state string is of the form {io,mem,io+mem,none}, mc and ic are respectively mem and io lock counts (for debugging/ diagnostic only). “decodes” indicate what the card currently decodes, “owns” indicates what is currently enabled on it, and “locks” indicates what is locked by this card. If the card is unplugged, we get “invalid” then for card_ID and an -ENODEV error is returned for any command until a new card is targeted.

write

Write a command to the arbiter. List of commands:

target <card_ID>

switch target to card <card_ID> (see below)

lock <io_state>

acquires locks on target (“none” is an invalid io_state)

trylock <io_state>

non-blocking acquire locks on target (returns EBUSY if unsuccessful)

unlock <io_state>

release locks on target

unlock all

release all locks on target held by this user (not implemented yet)

decodes <io_state>

set the legacy decoding attributes for the card

poll

event if something changes on any card (not just the target)

card_ID is of the form “PCI:domain:bus:dev.fn”. It can be set to “default” to go back to the system default card (TODO: not implemented yet). Currently, only PCI is supported as a prefix, but the userland API may support other bus types in the future, even if the current kernel implementation doesn’t.

Note about locks:

The driver keeps track of which user has which locks on which card. It supports stacking, like the kernel one. This complexifies the implementation a bit, but makes the arbiter more tolerant to user space problems and able to properly cleanup in all cases when a process dies. Currently, a max of 16 cards can have locks simultaneously issued from user space for a given user (file descriptor instance) of the arbiter.

In the case of devices hot-{un,}plugged, there is a hook - pci_notify() - to notify them being added/removed in the system and automatically added/removed in the arbiter.

There is also an in-kernel API of the arbiter in case DRM, vgacon, or other drivers want to use it.

In-kernel interface

int vga_get_interruptible(struct pci_dev *pdev, unsigned int rsrc)

Parameters

struct pci_dev *pdev

pci device of the VGA card or NULL for the system default

unsigned int rsrc

bit mask of resources to acquire and lock

Description

Shortcut to vga_get with interruptible set to true.

On success, release the VGA resource again with vga_put().

int vga_get_uninterruptible(struct pci_dev *pdev, unsigned int rsrc)

shortcut to vga_get()

Parameters

struct pci_dev *pdev

pci device of the VGA card or NULL for the system default

unsigned int rsrc

bit mask of resources to acquire and lock

Description

Shortcut to vga_get with interruptible set to false.

On success, release the VGA resource again with vga_put().

struct pci_dev * vga_default_device(void)

return the default VGA device, for vgacon

Parameters

void

no arguments

Description

This can be defined by the platform. The default implementation is rather dumb and will probably only work properly on single vga card setups and/or x86 platforms.

If your VGA default device is not PCI, you’ll have to return NULL here. In this case, I assume it will not conflict with any PCI card. If this is not true, I’ll have to define two archs hooks for enabling/disabling the VGA default device if that is possible. This may be a problem with real _ISA_ VGA cards, in addition to a PCI one. I don’t know at this point how to deal with that card. Can theirs IOs be disabled at all ? If not, then I suppose it’s a matter of having the proper arch hook telling us about it, so we basically never allow anybody to succeed a vga_get()

int vga_remove_vgacon(struct pci_dev *pdev)

deactivete vga console

Parameters

struct pci_dev *pdev

pci device.

Description

Unbind and unregister vgacon in case pdev is the default vga device. Can be called by gpu drivers on initialization to make sure vga register access done by vgacon will not disturb the device.

int vga_get(struct pci_dev *pdev, unsigned int rsrc, int interruptible)

acquire & locks VGA resources

Parameters

struct pci_dev *pdev

pci device of the VGA card or NULL for the system default

unsigned int rsrc

bit mask of resources to acquire and lock

int interruptible

blocking should be interruptible by signals ?

Description

This function acquires VGA resources for the given card and mark those resources locked. If the resource requested are “normal” (and not legacy) resources, the arbiter will first check whether the card is doing legacy decoding for that type of resource. If yes, the lock is “converted” into a legacy resource lock.

The arbiter will first look for all VGA cards that might conflict and disable their IOs and/or Memory access, including VGA forwarding on P2P bridges if necessary, so that the requested resources can be used. Then, the card is marked as locking these resources and the IO and/or Memory accesses are enabled on the card (including VGA forwarding on parent P2P bridges if any).

This function will block if some conflicting card is already locking one of the required resources (or any resource on a different bus segment, since P2P bridges don’t differentiate VGA memory and IO afaik). You can indicate whether this blocking should be interruptible by a signal (for userland interface) or not.

Must not be called at interrupt time or in atomic context. If the card already owns the resources, the function succeeds. Nested calls are supported (a per-resource counter is maintained)

On success, release the VGA resource again with vga_put().

0 on success, negative error code on failure.

Return

void vga_put(struct pci_dev *pdev, unsigned int rsrc)

release lock on legacy VGA resources

Parameters

struct pci_dev *pdev

pci device of VGA card or NULL for system default

unsigned int rsrc

but mask of resource to release

Description

This fuction releases resources previously locked by vga_get() or vga_tryget(). The resources aren’t disabled right away, so that a subsequence vga_get() on the same card will succeed immediately. Resources have a counter, so locks are only released if the counter reaches 0.

void vga_set_legacy_decoding(struct pci_dev *pdev, unsigned int decodes)

Parameters

struct pci_dev *pdev

pci device of the VGA card

unsigned int decodes

bit mask of what legacy regions the card decodes

Description

Indicates to the arbiter if the card decodes legacy VGA IOs, legacy VGA Memory, both, or none. All cards default to both, the card driver (fbdev for example) should tell the arbiter if it has disabled legacy decoding, so the card can be left out of the arbitration process (and can be safe to take interrupts at any time.

int vga_client_register(struct pci_dev *pdev, unsigned int (*set_decode)(struct pci_dev *pdev, bool decode))

register or unregister a VGA arbitration client

Parameters

struct pci_dev *pdev

pci device of the VGA client

unsigned int (*set_decode)(struct pci_dev *pdev, bool decode)

vga decode change callback

Description

Clients have two callback mechanisms they can use.

set_decode callback: If a client can disable its GPU VGA resource, it will get a callback from this to set the encode/decode state.

Rationale: we cannot disable VGA decode resources unconditionally some single GPU laptops seem to require ACPI or BIOS access to the VGA registers to control things like backlights etc. Hopefully newer multi-GPU laptops do something saner, and desktops won’t have any special ACPI for this. The driver will get a callback when VGA arbitration is first used by userspace since some older X servers have issues.

This function does not check whether a client for pdev has been registered already.

To unregister just call vga_client_unregister().

Return

0 on success, -1 on failure

libpciaccess

To use the vga arbiter char device it was implemented an API inside the libpciaccess library. One field was added to struct pci_device (each device on the system):

/* the type of resource decoded by the device */
int vgaarb_rsrc;

Besides it, in pci_system were added:

int vgaarb_fd;
int vga_count;
struct pci_device *vga_target;
struct pci_device *vga_default_dev;

The vga_count is used to track how many cards are being arbitrated, so for instance, if there is only one card, then it can completely escape arbitration.

These functions below acquire VGA resources for the given card and mark those resources as locked. If the resources requested are “normal” (and not legacy) resources, the arbiter will first check whether the card is doing legacy decoding for that type of resource. If yes, the lock is “converted” into a legacy resource lock. The arbiter will first look for all VGA cards that might conflict and disable their IOs and/or Memory access, including VGA forwarding on P2P bridges if necessary, so that the requested resources can be used. Then, the card is marked as locking these resources and the IO and/or Memory access is enabled on the card (including VGA forwarding on parent P2P bridges if any). In the case of vga_arb_lock(), the function will block if some conflicting card is already locking one of the required resources (or any resource on a different bus segment, since P2P bridges don’t differentiate VGA memory and IO afaik). If the card already owns the resources, the function succeeds. vga_arb_trylock() will return (-EBUSY) instead of blocking. Nested calls are supported (a per-resource counter is maintained).

Set the target device of this client.

int  pci_device_vgaarb_set_target   (struct pci_device *dev);

For instance, in x86 if two devices on the same bus want to lock different resources, both will succeed (lock). If devices are in different buses and trying to lock different resources, only the first who tried succeeds.

int  pci_device_vgaarb_lock         (void);
int  pci_device_vgaarb_trylock      (void);

Unlock resources of device.

int  pci_device_vgaarb_unlock       (void);

Indicates to the arbiter if the card decodes legacy VGA IOs, legacy VGA Memory, both, or none. All cards default to both, the card driver (fbdev for example) should tell the arbiter if it has disabled legacy decoding, so the card can be left out of the arbitration process (and can be safe to take interrupts at any time.

int  pci_device_vgaarb_decodes      (int new_vgaarb_rsrc);

Connects to the arbiter device, allocates the struct

int  pci_device_vgaarb_init         (void);

Close the connection

void pci_device_vgaarb_fini         (void);

xf86VGAArbiter (X server implementation)

X server basically wraps all the functions that touch VGA registers somehow.

References

Benjamin Herrenschmidt (IBM?) started this work when he discussed such design with the Xorg community in 2005 [1, 2]. In the end of 2007, Paulo Zanoni and Tiago Vignatti (both of C3SL/Federal University of Paraná) proceeded his work enhancing the kernel code to adapt as a kernel module and also did the implementation of the user space side [3]. Now (2009) Tiago Vignatti and Dave Airlie finally put this work in shape and queued to Jesse Barnes’ PCI tree.

  1. https://cgit.freedesktop.org/xorg/xserver/commit/?id=4b42448a2388d40f257774fbffdccaea87bd0347

  2. https://lists.freedesktop.org/archives/xorg/2005-March/006663.html

  3. https://lists.freedesktop.org/archives/xorg/2005-March/006745.html

  4. https://lists.freedesktop.org/archives/xorg/2007-October/029507.html