Proc Files of ALSA Drivers¶
Takashi Iwai <email@example.com>
ALSA has its own proc tree, /proc/asound. Many useful information are found in this tree. When you encounter a problem and need debugging, check the files listed in the following sections.
Each card has its subtree cardX, where X is from 0 to 7. The
card-specific files are stored in the
Shows the list of currently configured ALSA drivers, index, the id string, short and long descriptions.
Shows the version string and compile date.
Lists the module of each card
Lists the ALSA native device mappings.
Shows the status of allocated pages via ALSA drivers. Appears only when
Lists the currently available hwdep devices in format of
Lists the currently available PCM devices in format of
<card>-<device>: <id>: <name> : <sub-streams>
Lists the currently available timer devices
Lists the OSS device mappings.
Provides the output compatible with /dev/sndstat. You can symlink this to /dev/sndstat.
Card Specific Files¶
The card-specific files are found in
Some drivers (e.g. cmipci) have their own proc entries for the
register dump, etc (e.g.
/proc/asound/card*/cmipci shows the register
dump). These files would be really helpful for debugging.
When PCM devices are available on this card, you can see directories
like pcm0p or pcm1c. They hold the PCM information for each PCM
stream. The number after
pcm is the PCM device number from 0, and
c means playback or capture direction. The files in
this subtree is described later.
The status of MIDI I/O is found in
midi* files. It shows the device
name and the received/transmitted bytes through the MIDI device.
When the card is equipped with AC97 codecs, there are
subdirectories (described later).
When the OSS mixer emulation is enabled (and the module is loaded), oss_mixer file appears here, too. This shows the current mapping of OSS mixer elements to the ALSA control elements. You can change the mapping by writing to this device. Read OSS-Emulation.txt for details.
PCM Proc Files¶
The general information of this PCM device: card #, device #, substreams, etc.
This file appears when
CONFIG_SND_PCM_XRUN_DEBUG=y. This shows the status of xrun (= buffer overrun/xrun) and invalid PCM position debug/check of ALSA PCM middle layer. It takes an integer value, can be changed by writing to this file, such as:
# echo 5 > /proc/asound/card0/pcm0p/xrun_debug
The value consists of the following bit flags:
bit 0 = Enable XRUN/jiffies debug messages
bit 1 = Show stack trace at XRUN / jiffies check
bit 2 = Enable additional jiffies check
When the bit 0 is set, the driver will show the messages to kernel log when an xrun is detected. The debug message is shown also when the invalid H/W pointer is detected at the update of periods (usually called from the interrupt handler).
When the bit 1 is set, the driver will show the stack trace additionally. This may help the debugging.
Since 2.6.30, this option can enable the hwptr check using jiffies. This detects spontaneous invalid pointer callback values, but can be lead to too much corrections for a (mostly buggy) hardware that doesn’t give smooth pointer updates. This feature is enabled via the bit 2.
The general information of this PCM sub-stream.
The current status of this PCM sub-stream, elapsed time, H/W position, etc.
The hardware parameters set for this sub-stream.
The soft parameters set for this sub-stream.
The buffer pre-allocation information.
Triggers an XRUN to the running stream when any value is written to this proc file. Used for fault injection. This entry is write-only.
AC97 Codec Information¶
Shows the general information of this AC97 codec chip, such as name, capabilities, set up.
Shows the AC97 register dump. Useful for debugging.
When CONFIG_SND_DEBUG is enabled, you can write to this file for changing an AC97 register directly. Pass two hex numbers. For example,
# echo 02 9f1f > /proc/asound/card0/codec97#0/ac97#0-0+regs
USB Audio Streams¶
Shows the assignment and the current status of each audio stream of the given card. This information is very useful for debugging.
Shows the general codec information and the attribute of each widget node.
Available for HDMI or DisplayPort interfaces. Shows ELD(EDID Like Data) info retrieved from the attached HDMI sink, and describes its audio capabilities and configurations.
Some ELD fields may be modified by doing
echo name hex_value > eld#*. Only do this if you are sure the HDMI sink provided value is wrong. And if that makes your HDMI audio work, please report to us so that we can fix it in future kernel releases.
Lists the currently available ALSA sequencer drivers.
Shows the list of currently available sequencer clients and ports. The connection status and the running status are shown in this file, too.
Lists the currently allocated/running sequencer queues.
Lists the currently allocated/running sequencer timers.
Lists the OSS-compatible sequencer stuffs.
Help For Debugging?¶
When the problem is related with PCM, first try to turn on xrun_debug mode. This will give you the kernel messages when and where xrun happened.
If it’s really a bug, report it with the following information:
the name of the driver/card, show in
the register dump, if available (e.g.
when it’s a PCM problem,
set-up of PCM, shown in hw_parms, sw_params, and status in the PCM sub-stream directory
when it’s a mixer problem,
AC97 proc files,
for USB audio/midi,
stream*files in card directory
The ALSA bug-tracking system is found at: https://bugtrack.alsa-project.org/alsa-bug/