Linux kernel driver for Elastic Network Adapter (ENA) family¶
ENA is a networking interface designed to make good use of modern CPU features and system architectures.
The ENA device exposes a lightweight management interface with a minimal set of memory mapped registers and extendable command set through an Admin Queue.
The driver supports a range of ENA devices, is link-speed independent (i.e., the same driver is used for 10GbE, 25GbE, 40GbE, etc.), and has a negotiated and extendable feature set.
Some ENA devices support SR-IOV. This driver is used for both the SR-IOV Physical Function (PF) and Virtual Function (VF) devices.
ENA devices enable high speed and low overhead network traffic processing by providing multiple Tx/Rx queue pairs (the maximum number is advertised by the device via the Admin Queue), a dedicated MSI-X interrupt vector per Tx/Rx queue pair, adaptive interrupt moderation, and CPU cacheline optimized data placement.
The ENA driver supports industry standard TCP/IP offload features such as checksum offload and TCP transmit segmentation offload (TSO). Receive-side scaling (RSS) is supported for multi-core scaling.
The ENA driver and its corresponding devices implement health monitoring mechanisms such as watchdog, enabling the device and driver to recover in a manner transparent to the application, as well as debug logs.
Some of the ENA devices support a working mode called Low-latency Queue (LLQ), which saves several more microseconds.
ENA Source Code Directory Structure¶
Management communication layer. This layer is responsible for the handling all the management (admin) communication between the device and the driver.
Tx/Rx data path.
Definition of ENA management interface.
Definition of ENA data path interface.
Common definitions for ena_com layer.
Definition of ENA PCI memory-mapped (MMIO) registers.
Main Linux kernel driver.
Supported device IDs.
ENA management interface is exposed by means of:
PCIe Configuration Space
Admin Queue (AQ) and Admin Completion Queue (ACQ)
Asynchronous Event Notification Queue (AENQ)
ENA device MMIO Registers are accessed only during driver initialization and are not involved in further normal device operation.
AQ is used for submitting management commands, and the results/responses are reported asynchronously through ACQ.
ENA introduces a small set of management commands with room for vendor-specific extensions. Most of the management operations are framed in a generic Get/Set feature command.
The following admin queue commands are supported:
Create I/O submission queue
Create I/O completion queue
Destroy I/O submission queue
Destroy I/O completion queue
Refer to ena_admin_defs.h for the list of supported Get/Set Feature properties.
The Asynchronous Event Notification Queue (AENQ) is a uni-directional queue used by the ENA device to send to the driver events that cannot be reported using ACQ. AENQ events are subdivided into groups. Each group may have multiple syndromes, as shown below
The events are:
Link state change
ACQ and AENQ share the same MSI-X vector.
Keep-Alive is a special mechanism that allows monitoring of the device’s health. The driver maintains a watchdog (WD) handler which, if fired, logs the current state and statistics then resets and restarts the ENA device and driver. A Keep-Alive event is delivered by the device every second. The driver re-arms the WD upon reception of a Keep-Alive event. A missed Keep-Alive event causes the WD handler to fire.
Data Path Interface¶
I/O operations are based on Tx and Rx Submission Queues (Tx SQ and Rx SQ correspondingly). Each SQ has a completion queue (CQ) associated with it.
The SQs and CQs are implemented as descriptor rings in contiguous physical memory.
The ENA driver supports two Queue Operation modes for Tx SQs:
In this mode the Tx SQs reside in the host’s memory. The ENA device fetches the ENA Tx descriptors and packet data from host memory.
Low Latency Queue (LLQ) mode or “push-mode”.
In this mode the driver pushes the transmit descriptors and the first 128 bytes of the packet directly to the ENA device memory space. The rest of the packet payload is fetched by the device. For this operation mode, the driver uses a dedicated PCI device memory BAR, which is mapped with write-combine capability.
The Rx SQs support only the regular mode.
- Note: Not all ENA devices support LLQ, and this feature is negotiated
with the device upon initialization. If the ENA device does not support LLQ mode, the driver falls back to the regular mode.
The driver supports multi-queue for both Tx and Rx. This has various benefits:
Reduced CPU/thread/process contention on a given Ethernet interface.
Cache miss rate on completion is reduced, particularly for data cache lines that hold the sk_buff structures.
Increased process-level parallelism when handling received packets.
Increased data cache hit rate, by steering kernel processing of packets to the CPU, where the application thread consuming the packet is running.
In hardware interrupt re-direction.
The driver assigns a single MSI-X vector per queue pair (for both Tx and Rx directions). The driver assigns an additional dedicated MSI-X vector for management (for ACQ and AENQ).
Management interrupt registration is performed when the Linux kernel probes the adapter, and it is de-registered when the adapter is removed. I/O queue interrupt registration is performed when the Linux interface of the adapter is opened, and it is de-registered when the interface is closed.
The management interrupt is named:
and for each queue pair, an interrupt is named:
<interface name>-Tx-Rx-<queue index>
The ENA device operates in auto-mask and auto-clear interrupt modes. That is, once MSI-X is delivered to the host, its Cause bit is automatically cleared and the interrupt is masked. The interrupt is unmasked by the driver after NAPI processing is complete.
ENA driver and device can operate in conventional or adaptive interrupt moderation mode.
In conventional mode the driver instructs device to postpone interrupt posting according to static interrupt delay value. The interrupt delay value can be configured through ethtool(8). The following ethtool parameters are supported by the driver: tx-usecs, rx-usecs
In adaptive interrupt moderation mode the interrupt delay value is updated by the driver dynamically and adjusted every NAPI cycle according to the traffic nature.
Adaptive coalescing can be switched on/off through ethtool(8) adaptive_rx on|off parameter.
More information about Adaptive Interrupt Moderation (DIM) can be found in Net DIM - Generic Network Dynamic Interrupt Moderation
The rx_copybreak is initialized by default to ENA_DEFAULT_RX_COPYBREAK and can be configured by the ETHTOOL_STUNABLE command of the SIOCETHTOOL ioctl.
The driver-allocated SKB for frames received from Rx handling using NAPI context. The allocation method depends on the size of the packet. If the frame length is larger than rx_copybreak, napi_get_frags() is used, otherwise netdev_alloc_skb_ip_align() is used, the buffer content is copied (by CPU) to the SKB, and the buffer is recycled.
The user can obtain ENA device and driver statistics using ethtool. The driver can collect regular or extended statistics (including per-queue stats) from the device.
In addition the driver logs the stats to syslog upon device reset.
The driver supports an arbitrarily large MTU with a maximum that is negotiated with the device. The driver configures MTU using the SetFeature command (ENA_ADMIN_MTU property). The user can change MTU via ip(8) and similar legacy tools.
The ENA driver supports:
TSO over IPv4/IPv6
TSO with ECN
IPv4 header checksum offload
TCP/UDP over IPv4/IPv6 checksum offloads
The ENA device supports RSS that allows flexible Rx traffic steering.
Toeplitz and CRC32 hash functions are supported.
Different combinations of L2/L3/L4 fields can be configured as inputs for hash functions.
The driver configures RSS settings using the AQ SetFeature command (ENA_ADMIN_RSS_HASH_FUNCTION, ENA_ADMIN_RSS_HASH_INPUT and ENA_ADMIN_RSS_INDIRECTION_TABLE_CONFIG properties).
If the NETIF_F_RXHASH flag is set, the 32-bit result of the hash function delivered in the Rx CQ descriptor is set in the received SKB.
The user can provide a hash key, hash function, and configure the indirection table through ethtool(8).
ena_start_xmit() is called by the stack. This function does the following:
Maps data buffers (skb->data and frags).
Populates ena_buf for the push buffer (if the driver and device are in push mode.)
Prepares ENA bufs for the remaining frags.
Allocates a new request ID from the empty req_id ring. The request ID is the index of the packet in the Tx info. This is used for out-of-order TX completions.
Adds the packet to the proper place in the Tx ring.
Calls ena_com_prepare_tx(), an ENA communication layer that converts the ena_bufs to ENA descriptors (and adds meta ENA descriptors as needed.)
This function also copies the ENA descriptors and the push buffer to the Device memory space (if in push mode.)
Writes doorbell to the ENA device.
When the ENA device finishes sending the packet, a completion interrupt is raised.
The interrupt handler schedules NAPI.
The ena_clean_tx_irq() function is called. This function handles the completion descriptors generated by the ENA, with a single completion descriptor per completed packet.
req_id is retrieved from the completion descriptor. The tx_info of the packet is retrieved via the req_id. The data buffers are unmapped and req_id is returned to the empty req_id ring.
The function stops when the completion descriptors are completed or the budget is reached.
When a packet is received from the ENA device.
The interrupt handler schedules NAPI.
The ena_clean_rx_irq() function is called. This function calls ena_rx_pkt(), an ENA communication layer function, which returns the number of descriptors used for a new unhandled packet, and zero if no new packet is found.
Then it calls the ena_clean_rx_irq() function.
ena_eth_rx_skb() checks packet length:
If the packet is small (len < rx_copybreak), the driver allocates a SKB for the new packet, and copies the packet payload into the SKB data buffer.
In this way the original data buffer is not passed to the stack and is reused for future Rx packets.
Otherwise the function unmaps the Rx buffer, then allocates the new SKB structure and hooks the Rx buffer to the SKB frags.
The new SKB is updated with the necessary information (protocol, checksum hw verify result, etc.), and then passed to the network stack, using the NAPI interface function napi_gro_receive().