Kernel Driver Lochnagar

Supported systems:
  • Cirrus Logic : Lochnagar 2

Author: Lucas A. Tanure Alves

Description

Lochnagar 2 features built-in Current Monitor circuitry that allows for the measurement of both voltage and current on up to eight of the supply voltage rails provided to the minicards. The Current Monitor does not require any hardware modifications or external circuitry to operate.

The current and voltage measurements are obtained through the standard register map interface to the Lochnagar board controller, and can therefore be monitored by software.

Sysfs attributes

temp1_input The Lochnagar board temperature (milliCelsius)
in0_input Measured voltage for DBVDD1 (milliVolts)
in0_label “DBVDD1”
curr1_input Measured current for DBVDD1 (milliAmps)
curr1_label “DBVDD1”
power1_average Measured average power for DBVDD1 (microWatts)
power1_average_interval Power averaging time input valid from 1 to 1708mS
power1_label “DBVDD1”
in1_input Measured voltage for 1V8 DSP (milliVolts)
in1_label “1V8 DSP”
curr2_input Measured current for 1V8 DSP (milliAmps)
curr2_label “1V8 DSP”
power2_average Measured average power for 1V8 DSP (microWatts)
power2_average_interval Power averaging time input valid from 1 to 1708mS
power2_label “1V8 DSP”
in2_input Measured voltage for 1V8 CDC (milliVolts)
in2_label “1V8 CDC”
curr3_input Measured current for 1V8 CDC (milliAmps)
curr3_label “1V8 CDC”
power3_average Measured average power for 1V8 CDC (microWatts)
power3_average_interval Power averaging time input valid from 1 to 1708mS
power3_label “1V8 CDC”
in3_input Measured voltage for VDDCORE DSP (milliVolts)
in3_label “VDDCORE DSP”
curr4_input Measured current for VDDCORE DSP (milliAmps)
curr4_label “VDDCORE DSP”
power4_average Measured average power for VDDCORE DSP (microWatts)
power4_average_interval Power averaging time input valid from 1 to 1708mS
power4_label “VDDCORE DSP”
in4_input Measured voltage for AVDD 1V8 (milliVolts)
in4_label “AVDD 1V8”
curr5_input Measured current for AVDD 1V8 (milliAmps)
curr5_label “AVDD 1V8”
power5_average Measured average power for AVDD 1V8 (microWatts)
power5_average_interval Power averaging time input valid from 1 to 1708mS
power5_label “AVDD 1V8”
curr6_input Measured current for SYSVDD (milliAmps)
curr6_label “SYSVDD”
power6_average Measured average power for SYSVDD (microWatts)
power6_average_interval Power averaging time input valid from 1 to 1708mS
power6_label “SYSVDD”
in6_input Measured voltage for VDDCORE CDC (milliVolts)
in6_label “VDDCORE CDC”
curr7_input Measured current for VDDCORE CDC (milliAmps)
curr7_label “VDDCORE CDC”
power7_average Measured average power for VDDCORE CDC (microWatts)
power7_average_interval Power averaging time input valid from 1 to 1708mS
power7_label “VDDCORE CDC”
in7_input Measured voltage for MICVDD (milliVolts)
in7_label “MICVDD”
curr8_input Measured current for MICVDD (milliAmps)
curr8_label “MICVDD”
power8_average Measured average power for MICVDD (microWatts)
power8_average_interval Power averaging time input valid from 1 to 1708mS
power8_label “MICVDD”
Note:
It is not possible to measure voltage on the SYSVDD rail.