Synopsys DesignWare Core SuperSpeed USB 3.0 Controller

Author:Felipe Balbi <felipe.balbi@linux.intel.com>
Date:April 2017

Introduction

The Synopsys DesignWare Core SuperSpeed USB 3.0 Controller (hereinafter referred to as DWC3) is a USB SuperSpeed compliant controller which can be configured in one of 4 ways:

  1. Peripheral-only configuration
  2. Host-only configuration
  3. Dual-Role configuration
  4. Hub configuration

Linux currently supports several versions of this controller. In all likelyhood, the version in your SoC is already supported. At the time of this writing, known tested versions range from 2.02a to 3.10a. As a rule of thumb, anything above 2.02a should work reliably well.

Currently, we have many known users for this driver. In alphabetical order:

  1. Cavium
  2. Intel Corporation
  3. Qualcomm
  4. Rockchip
  5. ST
  6. Samsung
  7. Texas Instruments
  8. Xilinx

Summary of Features

For details about features supported by your version of DWC3, consult your IP team and/or Synopsys DesignWare Core SuperSpeed USB 3.0 Controller Databook. Following is a list of features supported by the driver at the time of this writing:

  1. Up to 16 bidirectional endpoints (including the control pipe - ep0)
  2. Flexible endpoint configuration
  3. Simultaneous IN and OUT transfer support
  4. Scatter-list support
  5. Up to 256 TRBs [1] per endpoint
  6. Support for all transfer types (Control, Bulk, Interrupt, and Isochronous)
  7. SuperSpeed Bulk Streams
  8. Link Power Management
  9. Trace Events for debugging
  10. DebugFS [3] interface

These features have all been exercised with many of the in-tree gadget drivers. We have verified both ConfigFS [4] and legacy gadget drivers.

Driver Design

The DWC3 driver sits on the drivers/usb/dwc3/ directory. All files related to this driver are in this one directory. This makes it easy for new-comers to read the code and understand how it behaves.

Because of DWC3’s configuration flexibility, the driver is a little complex in some places but it should be rather straightforward to understand.

The biggest part of the driver refers to the Gadget API.

Known Limitations

Like any other HW, DWC3 has its own set of limitations. To avoid constant questions about such problems, we decided to document them here and have a single location to where we could point users.

OUT Transfer Size Requirements

According to Synopsys Databook, all OUT transfer TRBs [1] must have their size field set to a value which is integer divisible by the endpoint’s wMaxPacketSize. This means that e.g. in order to receive a Mass Storage CBW [5], req->length must either be set to a value that’s divisible by wMaxPacketSize (1024 on SuperSpeed, 512 on HighSpeed, etc), or DWC3 driver must add a Chained TRB pointing to a throw-away buffer for the remaining length. Without this, OUT transfers will NOT start.

Note that as of this writing, this won’t be a problem because DWC3 is fully capable of appending a chained TRB for the remaining length and completely hide this detail from the gadget driver. It’s still worth mentioning because this seems to be the largest source of queries about DWC3 and non-working transfers.

TRB Ring Size Limitation

We, currently, have a hard limit of 256 TRBs [1] per endpoint, with the last TRB being a Link TRB [2] pointing back to the first. This limit is arbitrary but it has the benefit of adding up to exactly 4096 bytes, or 1 Page.

DWC3 driver will try its best to cope with more than 255 requests and, for the most part, it should work normally. However this is not something that has been exercised very frequently. If you experience any problems, see section Reporting Bugs below.

Reporting Bugs

Whenever you encounter a problem with DWC3, first and foremost you should make sure that:

  1. You’re running latest tag from Linus’ tree
  2. You can reproduce the error without any out-of-tree changes to DWC3
  3. You have checked that it’s not a fault on the host machine

After all these are verified, then here’s how to capture enough information so we can be of any help to you.

Required Information

DWC3 relies exclusively on Trace Events for debugging. Everything is exposed there, with some extra bits being exposed to DebugFS [3].

In order to capture DWC3’s Trace Events you should run the following commands before plugging the USB cable to a host machine:

# mkdir -p /d
# mkdir -p /t
# mount -t debugfs none /d
# mount -t tracefs none /t
# echo 81920 > /t/buffer_size_kb
# echo 1 > /t/events/dwc3/enable

After this is done, you can connect your USB cable and reproduce the problem. As soon as the fault is reproduced, make a copy of files trace and regdump, like so:

# cp /t/trace /root/trace.txt
# cat /d/*dwc3*/regdump > /root/regdump.txt

Make sure to compress trace.txt and regdump.txt in a tarball and email it to me with linux-usb in Cc. If you want to be extra sure that I’ll help you, write your subject line in the following format:

[BUG REPORT] usb: dwc3: Bug while doing XYZ

On the email body, make sure to detail what you doing, which gadget driver you were using, how to reproduce the problem, what SoC you’re using, which OS (and its version) was running on the Host machine.

With all this information, we should be able to understand what’s going on and be helpful to you.

Debugging

First and foremost a disclaimer:

DISCLAIMER: The information available on DebugFS and/or TraceFS can
change at any time at any Major Linux Kernel Release. If writing
scripts, do **NOT** assume information to be available in the
current format.

With that out of the way, let’s carry on.

If you’re willing to debug your own problem, you deserve a round of applause :-)

Anyway, there isn’t much to say here other than Trace Events will be really helpful in figuring out issues with DWC3. Also, access to Synopsys Databook will be really valuable in this case.

A USB Sniffer can be helpful at times but it’s not entirely required, there’s a lot that can be understood without looking at the wire.

Feel free to email me and Cc linux-usb if you need any help.

DebugFS

DebugFS is very good for gathering snapshots of what’s going on with DWC3 and/or any endpoint.

On DWC3’s DebugFS directory, you will find the following files and directories:

ep[0..15]{in,out}/ link_state regdump testmode

regdump

File name is self-explanatory. When read, regdump will print out a register dump of DWC3. Note that this file can be grepped to find the information you want.

testmode

When read, testmode will print out a name of one of the specified USB 2.0 Testmodes (test_j, test_k, test_se0_nak, test_packet, test_force_enable) or the string no test in case no tests are currently being executed.

In order to start any of these test modes, the same strings can be written to the file and DWC3 will enter the requested test mode.

ep[0..15]{in,out}

For each endpoint we expose one directory following the naming convention ep$num$dir (ep0in, ep0out, ep1in, ...). Inside each of these directories you will find the following files:

descriptor_fetch_queue event_queue rx_fifo_queue rx_info_queue rx_request_queue transfer_type trb_ring tx_fifo_queue tx_request_queue

With access to Synopsys Databook, you can decode the information on them.

transfer_type

When read, transfer_type will print out one of control, bulk, interrupt or isochronous depending on what the endpoint descriptor says. If the endpoint hasn’t been enabled yet, it will print --.

trb_ring

When read, trb_ring will print out details about all TRBs on the ring. It will also tell you where our enqueue and dequeue pointers are located in the ring:

buffer_addr,size,type,ioc,isp_imi,csp,chn,lst,hwo
000000002c754000,481,normal,1,0,1,0,0,0
000000002c75c000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c75c000,481,normal,1,0,1,0,0,0
000000002c784000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c784000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c784000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c784000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c75c000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c75c000,481,normal,1,0,1,0,0,0
000000002c780000,481,normal,1,0,1,0,0,0
000000002c784000,481,normal,1,0,1,0,0,0
000000002c788000,481,normal,1,0,1,0,0,0
000000002c78c000,481,normal,1,0,1,0,0,0
000000002c790000,481,normal,1,0,1,0,0,0
000000002c754000,481,normal,1,0,1,0,0,0
000000002c758000,481,normal,1,0,1,0,0,0
000000002c75c000,512,normal,1,0,1,0,0,1        D
0000000000000000,0,UNKNOWN,0,0,0,0,0,0       E
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
0000000000000000,0,UNKNOWN,0,0,0,0,0,0
00000000381ab000,0,link,0,0,0,0,0,1

Trace Events

DWC3 also provides several trace events which help us gathering information about the behavior of the driver during runtime.

In order to use these events, you must enable CONFIG_FTRACE in your kernel config.

For details about how enable DWC3 events, see section Reporting Bugs.

The following subsections will give details about each Event Class and each Event defined by DWC3.

MMIO

It is sometimes useful to look at every MMIO access when looking for bugs. Because of that, DWC3 offers two Trace Events (one for dwc3_readl() and one for dwc3_writel()). TP_printk follows:

TP_printk("addr %p value %08x", __entry->base + __entry->offset,
              __entry->value)

Interrupt Events

Every IRQ event can be logged and decoded into a human readable string. Because every event will be different, we don’t give an example other than the TP_printk format used:

TP_printk("event (%08x): %s", __entry->event,
              dwc3_decode_event(__entry->event, __entry->ep0state))

Control Request

Every USB Control Request can be logged to the trace buffer. The output format is:

TP_printk("%s", dwc3_decode_ctrl(__entry->bRequestType,
                              __entry->bRequest, __entry->wValue,
                              __entry->wIndex, __entry->wLength)
)

Note that Standard Control Requests will be decoded into human-readable strings with their respective arguments. Class and Vendor requests will be printed out a sequence of 8 bytes in hex format.

Lifetime of a struct usb_request

The entire lifetime of a struct usb_request can be tracked on the trace buffer. We have one event for each of allocation, free, queueing, dequeueing, and giveback. Output format is:

TP_printk("%s: req %p length %u/%u %s%s%s ==> %d",
      __get_str(name), __entry->req, __entry->actual, __entry->length,
      __entry->zero ? "Z" : "z",
      __entry->short_not_ok ? "S" : "s",
      __entry->no_interrupt ? "i" : "I",
      __entry->status
)

Generic Commands

We can log and decode every Generic Command with its completion code. Format is:

TP_printk("cmd '%s' [%x] param %08x --> status: %s",
      dwc3_gadget_generic_cmd_string(__entry->cmd),
      __entry->cmd, __entry->param,
      dwc3_gadget_generic_cmd_status_string(__entry->status)
)

Endpoint Commands

Endpoints commands can also be logged together with completion code. Format is:

TP_printk("%s: cmd '%s' [%d] params %08x %08x %08x --> status: %s",
      __get_str(name), dwc3_gadget_ep_cmd_string(__entry->cmd),
      __entry->cmd, __entry->param0,
      __entry->param1, __entry->param2,
      dwc3_ep_cmd_status_string(__entry->cmd_status)
)

Lifetime of a TRB

A TRB Lifetime is simple. We are either preparing a TRB or completing it. With these two events, we can see how a TRB changes over time. Format is:

TP_printk("%s: %d/%d trb %p buf %08x%08x size %s%d ctrl %08x (%c%c%c%c:%c%c:%s)",
      __get_str(name), __entry->queued, __entry->allocated,
      __entry->trb, __entry->bph, __entry->bpl,
      ({char *s;
      int pcm = ((__entry->size >> 24) & 3) + 1;
      switch (__entry->type) {
      case USB_ENDPOINT_XFER_INT:
      case USB_ENDPOINT_XFER_ISOC:
              switch (pcm) {
              case 1:
                      s = "1x ";
                      break;
              case 2:
                      s = "2x ";
                      break;
              case 3:
                      s = "3x ";
                      break;
              }
      default:
              s = "";
      } s; }),
      DWC3_TRB_SIZE_LENGTH(__entry->size), __entry->ctrl,
      __entry->ctrl & DWC3_TRB_CTRL_HWO ? 'H' : 'h',
      __entry->ctrl & DWC3_TRB_CTRL_LST ? 'L' : 'l',
      __entry->ctrl & DWC3_TRB_CTRL_CHN ? 'C' : 'c',
      __entry->ctrl & DWC3_TRB_CTRL_CSP ? 'S' : 's',
      __entry->ctrl & DWC3_TRB_CTRL_ISP_IMI ? 'S' : 's',
      __entry->ctrl & DWC3_TRB_CTRL_IOC ? 'C' : 'c',
    dwc3_trb_type_string(DWC3_TRBCTL_TYPE(__entry->ctrl))
)

Lifetime of an Endpoint

And endpoint’s lifetime is summarized with enable and disable operations, both of which can be traced. Format is:

TP_printk("%s: mps %d/%d streams %d burst %d ring %d/%d flags %c:%c%c%c%c%c:%c:%c",
      __get_str(name), __entry->maxpacket,
      __entry->maxpacket_limit, __entry->max_streams,
      __entry->maxburst, __entry->trb_enqueue,
      __entry->trb_dequeue,
      __entry->flags & DWC3_EP_ENABLED ? 'E' : 'e',
      __entry->flags & DWC3_EP_STALL ? 'S' : 's',
      __entry->flags & DWC3_EP_WEDGE ? 'W' : 'w',
      __entry->flags & DWC3_EP_BUSY ? 'B' : 'b',
      __entry->flags & DWC3_EP_PENDING_REQUEST ? 'P' : 'p',
      __entry->flags & DWC3_EP_MISSED_ISOC ? 'M' : 'm',
      __entry->flags & DWC3_EP_END_TRANSFER_PENDING ? 'E' : 'e',
      __entry->direction ? '<' : '>'
)

Structures, Methods and Definitions

struct dwc3_event_buffer

Software event buffer representation

Definition

struct dwc3_event_buffer {
  void *buf;
  void *cache;
  unsigned length;
  unsigned int            lpos;
  unsigned int            count;
  unsigned int            flags;
#define DWC3_EVENT_PENDING      BIT(0);
  dma_addr_t dma;
  struct dwc3             *dwc;
};

Members

buf
_THE_ buffer
cache
The buffer cache used in the threaded interrupt
length
size of this buffer
lpos
event offset
count
cache of last read event count register
flags
flags related to this event buffer
dma
dma_addr_t
dwc
pointer to DWC controller
struct dwc3_ep

device side endpoint representation

Definition

struct dwc3_ep {
  struct usb_ep           endpoint;
  struct list_head        pending_list;
  struct list_head        started_list;
  wait_queue_head_t wait_end_transfer;
  spinlock_t lock;
  void __iomem            *regs;
  struct dwc3_trb         *trb_pool;
  dma_addr_t trb_pool_dma;
  struct dwc3             *dwc;
  u32 saved_state;
  unsigned flags;
#define DWC3_EP_ENABLED         BIT(0);
#define DWC3_EP_STALL           BIT(1);
#define DWC3_EP_WEDGE           BIT(2);
#define DWC3_EP_BUSY            BIT(4);
#define DWC3_EP_PENDING_REQUEST BIT(5);
#define DWC3_EP_MISSED_ISOC     BIT(6);
#define DWC3_EP_END_TRANSFER_PENDING    BIT(7);
#define DWC3_EP_TRANSFER_STARTED BIT(8);
#define DWC3_EP0_DIR_IN         BIT(31);
  u8 trb_enqueue;
  u8 trb_dequeue;
  u8 number;
  u8 type;
  u8 resource_index;
  u32 allocated_requests;
  u32 queued_requests;
  u32 frame_number;
  u32 interval;
  char name[20];
  unsigned direction:1;
  unsigned stream_capable:1;
};

Members

endpoint
usb endpoint
pending_list
list of pending requests for this endpoint
started_list
list of started requests on this endpoint
wait_end_transfer
wait_queue_head_t for waiting on End Transfer complete
lock
spinlock for endpoint request queue traversal
regs
pointer to first endpoint register
trb_pool
array of transaction buffers
trb_pool_dma
dma address of trb_pool
dwc
pointer to DWC controller
saved_state
ep state saved during hibernation
flags
endpoint flags (wedged, stalled, ...)
trb_enqueue
enqueue ‘pointer’ into TRB array
trb_dequeue
dequeue ‘pointer’ into TRB array
number
endpoint number (1 - 15)
type
set to bmAttributes & USB_ENDPOINT_XFERTYPE_MASK
resource_index
Resource transfer index
allocated_requests
number of requests allocated
queued_requests
number of requests queued for transfer
frame_number
set to the frame number we want this transfer to start (ISOC)
interval
the interval on which the ISOC transfer is started
name
a human readable name e.g. ep1out-bulk
direction
true for TX, false for RX
stream_capable
true when streams are enabled
struct dwc3_trb

transfer request block (hw format)

Definition

struct dwc3_trb {
  u32 bpl;
  u32 bph;
  u32 size;
  u32 ctrl;
};

Members

bpl
DW0-3
bph
DW4-7
size
DW8-B
ctrl
DWC-F
struct dwc3_hwparams

copy of HWPARAMS registers

Definition

struct dwc3_hwparams {
  u32 hwparams0;
  u32 hwparams1;
  u32 hwparams2;
  u32 hwparams3;
  u32 hwparams4;
  u32 hwparams5;
  u32 hwparams6;
  u32 hwparams7;
  u32 hwparams8;
};

Members

hwparams0
GHWPARAMS0
hwparams1
GHWPARAMS1
hwparams2
GHWPARAMS2
hwparams3
GHWPARAMS3
hwparams4
GHWPARAMS4
hwparams5
GHWPARAMS5
hwparams6
GHWPARAMS6
hwparams7
GHWPARAMS7
hwparams8
GHWPARAMS8
struct dwc3_request

representation of a transfer request

Definition

struct dwc3_request {
  struct usb_request      request;
  struct list_head        list;
  struct dwc3_ep          *dep;
  struct scatterlist      *sg;
  unsigned num_pending_sgs;
  unsigned remaining;
  u8 epnum;
  struct dwc3_trb         *trb;
  dma_addr_t trb_dma;
  unsigned unaligned:1;
  unsigned direction:1;
  unsigned mapped:1;
  unsigned started:1;
  unsigned zero:1;
};

Members

request
struct usb_request to be transferred
list
a list_head used for request queueing
dep
struct dwc3_ep owning this request
sg
pointer to first incomplete sg
num_pending_sgs
counter to pending sgs
remaining
amount of data remaining
epnum
endpoint number to which this request refers
trb
pointer to struct dwc3_trb
trb_dma
DMA address of trb
unaligned
true for OUT endpoints with length not divisible by maxp
direction
IN or OUT direction flag
mapped
true when request has been dma-mapped
started
request is started
zero
wants a ZLP
struct dwc3

representation of our controller

Definition

struct dwc3 {
  struct work_struct      drd_work;
  struct dwc3_trb         *ep0_trb;
  void *bounce;
  void *scratchbuf;
  u8 *setup_buf;
  dma_addr_t ep0_trb_addr;
  dma_addr_t bounce_addr;
  dma_addr_t scratch_addr;
  struct dwc3_request     ep0_usb_req;
  struct completion       ep0_in_setup;
  spinlock_t lock;
  struct device           *dev;
  struct device           *sysdev;
  struct platform_device  *xhci;
  struct resource         xhci_resources[DWC3_XHCI_RESOURCES_NUM];
  struct dwc3_event_buffer *ev_buf;
  struct dwc3_ep          *eps[DWC3_ENDPOINTS_NUM];
  struct usb_gadget       gadget;
  struct usb_gadget_driver *gadget_driver;
  struct usb_phy          *usb2_phy;
  struct usb_phy          *usb3_phy;
  struct phy              *usb2_generic_phy;
  struct phy              *usb3_generic_phy;
  bool phys_ready;
  struct ulpi             *ulpi;
  bool ulpi_ready;
  void __iomem            *regs;
  size_t regs_size;
  enum usb_dr_mode        dr_mode;
  u32 current_dr_role;
  u32 desired_dr_role;
  struct extcon_dev       *edev;
  struct notifier_block   edev_nb;
  enum usb_phy_interface  hsphy_mode;
  u32 fladj;
  u32 irq_gadget;
  u32 nr_scratch;
  u32 u1u2;
  u32 maximum_speed;
  u32 revision;
#define DWC3_REVISION_173A      0x5533173a;
#define DWC3_REVISION_175A      0x5533175a;
#define DWC3_REVISION_180A      0x5533180a;
#define DWC3_REVISION_183A      0x5533183a;
#define DWC3_REVISION_185A      0x5533185a;
#define DWC3_REVISION_187A      0x5533187a;
#define DWC3_REVISION_188A      0x5533188a;
#define DWC3_REVISION_190A      0x5533190a;
#define DWC3_REVISION_194A      0x5533194a;
#define DWC3_REVISION_200A      0x5533200a;
#define DWC3_REVISION_202A      0x5533202a;
#define DWC3_REVISION_210A      0x5533210a;
#define DWC3_REVISION_220A      0x5533220a;
#define DWC3_REVISION_230A      0x5533230a;
#define DWC3_REVISION_240A      0x5533240a;
#define DWC3_REVISION_250A      0x5533250a;
#define DWC3_REVISION_260A      0x5533260a;
#define DWC3_REVISION_270A      0x5533270a;
#define DWC3_REVISION_280A      0x5533280a;
#define DWC3_REVISION_290A      0x5533290a;
#define DWC3_REVISION_300A      0x5533300a;
#define DWC3_REVISION_310A      0x5533310a;
#define DWC3_REVISION_IS_DWC31          0x80000000;
#define DWC3_USB31_REVISION_110A        (0x3131302a | DWC3_REVISION_IS_DWC31);
#define DWC3_USB31_REVISION_120A        (0x3132302a | DWC3_REVISION_IS_DWC31);
  enum dwc3_ep0_next      ep0_next_event;
  enum dwc3_ep0_state     ep0state;
  enum dwc3_link_state    link_state;
  u16 u2sel;
  u16 u2pel;
  u8 u1sel;
  u8 u1pel;
  u8 speed;
  u8 num_eps;
  struct dwc3_hwparams    hwparams;
  struct dentry           *root;
  struct debugfs_regset32 *regset;
  u8 test_mode;
  u8 test_mode_nr;
  u8 lpm_nyet_threshold;
  u8 hird_threshold;
  const char              *hsphy_interface;
  unsigned connected:1;
  unsigned delayed_status:1;
  unsigned ep0_bounced:1;
  unsigned ep0_expect_in:1;
  unsigned has_hibernation:1;
  unsigned sysdev_is_parent:1;
  unsigned has_lpm_erratum:1;
  unsigned is_utmi_l1_suspend:1;
  unsigned is_fpga:1;
  unsigned pending_events:1;
  unsigned pullups_connected:1;
  unsigned setup_packet_pending:1;
  unsigned three_stage_setup:1;
  unsigned usb3_lpm_capable:1;
  unsigned disable_scramble_quirk:1;
  unsigned u2exit_lfps_quirk:1;
  unsigned u2ss_inp3_quirk:1;
  unsigned req_p1p2p3_quirk:1;
  unsigned del_p1p2p3_quirk:1;
  unsigned del_phy_power_chg_quirk:1;
  unsigned lfps_filter_quirk:1;
  unsigned rx_detect_poll_quirk:1;
  unsigned dis_u3_susphy_quirk:1;
  unsigned dis_u2_susphy_quirk:1;
  unsigned dis_enblslpm_quirk:1;
  unsigned dis_rxdet_inp3_quirk:1;
  unsigned dis_u2_freeclk_exists_quirk:1;
  unsigned dis_del_phy_power_chg_quirk:1;
  unsigned dis_tx_ipgap_linecheck_quirk:1;
  unsigned tx_de_emphasis_quirk:1;
  unsigned tx_de_emphasis:2;
  unsigned dis_metastability_quirk:1;
  u16 imod_interval;
};

Members

drd_work
workqueue used for role swapping
ep0_trb
trb which is used for the ctrl_req
bounce
address of bounce buffer
scratchbuf
address of scratch buffer
setup_buf
used while precessing STD USB requests
ep0_trb_addr
dma address of ep0_trb
bounce_addr
dma address of bounce
scratch_addr
dma address of scratchbuf
ep0_usb_req
dummy req used while handling STD USB requests
ep0_in_setup
one control transfer is completed and enter setup phase
lock
for synchronizing
dev
pointer to our struct device
sysdev
pointer to the DMA-capable device
xhci
pointer to our xHCI child
xhci_resources
struct resources for our xhci child
ev_buf
struct dwc3_event_buffer pointer
eps
endpoint array
gadget
device side representation of the peripheral controller
gadget_driver
pointer to the gadget driver
usb2_phy
pointer to USB2 PHY
usb3_phy
pointer to USB3 PHY
usb2_generic_phy
pointer to USB2 PHY
usb3_generic_phy
pointer to USB3 PHY
phys_ready
flag to indicate that PHYs are ready
ulpi
pointer to ulpi interface
ulpi_ready
flag to indicate that ULPI is initialized
regs
base address for our registers
regs_size
address space size
dr_mode
requested mode of operation
current_dr_role
current role of operation when in dual-role mode
desired_dr_role
desired role of operation when in dual-role mode
edev
extcon handle
edev_nb
extcon notifier
hsphy_mode
UTMI phy mode, one of following: - USBPHY_INTERFACE_MODE_UTMI - USBPHY_INTERFACE_MODE_UTMIW
fladj
frame length adjustment
irq_gadget
peripheral controller’s IRQ number
nr_scratch
number of scratch buffers
u1u2
only used on revisions <1.83a for workaround
maximum_speed
maximum speed requested (mainly for testing purposes)
revision
revision register contents
ep0_next_event
hold the next expected event
ep0state
state of endpoint zero
link_state
link state
u2sel
parameter from Set SEL request.
u2pel
parameter from Set SEL request.
u1sel
parameter from Set SEL request.
u1pel
parameter from Set SEL request.
speed
device speed (super, high, full, low)
num_eps
number of endpoints
hwparams
copy of hwparams registers
root
debugfs root folder pointer
regset
debugfs pointer to regdump file
test_mode
true when we’re entering a USB test mode
test_mode_nr
test feature selector
lpm_nyet_threshold
LPM NYET response threshold
hird_threshold
HIRD threshold
hsphy_interface
“utmi” or “ulpi”
connected
true when we’re connected to a host, false otherwise
delayed_status
true when gadget driver asks for delayed status
ep0_bounced
true when we used bounce buffer
ep0_expect_in
true when we expect a DATA IN transfer
has_hibernation
true when dwc3 was configured with Hibernation
sysdev_is_parent
true when dwc3 device has a parent driver
has_lpm_erratum
true when core was configured with LPM Erratum. Note that there’s now way for software to detect this in runtime.
is_utmi_l1_suspend
the core asserts output signal 0 - utmi_sleep_n 1 - utmi_l1_suspend_n
is_fpga
true when we are using the FPGA board
pending_events
true when we have pending IRQs to be handled
pullups_connected
true when Run/Stop bit is set
setup_packet_pending
true when there’s a Setup Packet in FIFO. Workaround
three_stage_setup
set if we perform a three phase setup
usb3_lpm_capable
set if hadrware supports Link Power Management
disable_scramble_quirk
set if we enable the disable scramble quirk
u2exit_lfps_quirk
set if we enable u2exit lfps quirk
u2ss_inp3_quirk
set if we enable P3 OK for U2/SS Inactive quirk
req_p1p2p3_quirk
set if we enable request p1p2p3 quirk
del_p1p2p3_quirk
set if we enable delay p1p2p3 quirk
del_phy_power_chg_quirk
set if we enable delay phy power change quirk
lfps_filter_quirk
set if we enable LFPS filter quirk
rx_detect_poll_quirk
set if we enable rx_detect to polling lfps quirk
dis_u3_susphy_quirk
set if we disable usb3 suspend phy
dis_u2_susphy_quirk
set if we disable usb2 suspend phy
dis_enblslpm_quirk
set if we clear enblslpm in GUSB2PHYCFG, disabling the suspend signal to the PHY.
dis_rxdet_inp3_quirk
set if we disable Rx.Detect in P3
dis_u2_freeclk_exists_quirk
set if we clear u2_freeclk_exists in GUSB2PHYCFG, specify that USB2 PHY doesn’t provide a free-running PHY clock.
dis_del_phy_power_chg_quirk
set if we disable delay phy power change quirk.
dis_tx_ipgap_linecheck_quirk
set if we disable u2mac linestate check during HS transmit.
tx_de_emphasis_quirk
set if we enable Tx de-emphasis quirk
tx_de_emphasis
Tx de-emphasis value 0 - -6dB de-emphasis 1 - -3.5dB de-emphasis 2 - No de-emphasis 3 - Reserved
dis_metastability_quirk
set to disable metastability quirk.
imod_interval
set the interrupt moderation interval in 250ns increments or 0 to disable.
struct dwc3_event_depevt

Device Endpoint Events

Definition

struct dwc3_event_depevt {
  u32 one_bit:1;
  u32 endpoint_number:5;
  u32 endpoint_event:4;
  u32 reserved11_10:2;
  u32 status:4;
#define DEPEVT_STATUS_TRANSFER_ACTIVE   BIT(3);
#define DEPEVT_STATUS_BUSERR    BIT(0);
#define DEPEVT_STATUS_SHORT     BIT(1);
#define DEPEVT_STATUS_IOC       BIT(2);
#define DEPEVT_STATUS_LST       BIT(3);
#define DEPEVT_STREAMEVT_FOUND          1;
#define DEPEVT_STREAMEVT_NOTFOUND       2;
#define DEPEVT_STATUS_CONTROL_DATA      1;
#define DEPEVT_STATUS_CONTROL_STATUS    2;
#define DEPEVT_STATUS_CONTROL_PHASE(n)  ((n) & 3);
#define DEPEVT_TRANSFER_NO_RESOURCE     1;
#define DEPEVT_TRANSFER_BUS_EXPIRY      2;
  u32 parameters:16;
#define DEPEVT_PARAMETER_CMD(n) (((n) & (0xf << 8)) >> 8);
};

Members

one_bit
indicates this is an endpoint event (not used)
endpoint_number
number of the endpoint
endpoint_event
The event we have: 0x00 - Reserved 0x01 - XferComplete 0x02 - XferInProgress 0x03 - XferNotReady 0x04 - RxTxFifoEvt (IN->Underrun, OUT->Overrun) 0x05 - Reserved 0x06 - StreamEvt 0x07 - EPCmdCmplt
reserved11_10
Reserved, don’t use.
status
Indicates the status of the event. Refer to databook for more information.
parameters
Parameters of the current event. Refer to databook for more information.
struct dwc3_event_devt

Device Events

Definition

struct dwc3_event_devt {
  u32 one_bit:1;
  u32 device_event:7;
  u32 type:4;
  u32 reserved15_12:4;
  u32 event_info:9;
  u32 reserved31_25:7;
};

Members

one_bit
indicates this is a non-endpoint event (not used)
device_event
indicates it’s a device event. Should read as 0x00
type
indicates the type of device event. 0 - DisconnEvt 1 - USBRst 2 - ConnectDone 3 - ULStChng 4 - WkUpEvt 5 - Reserved 6 - EOPF 7 - SOF 8 - Reserved 9 - ErrticErr 10 - CmdCmplt 11 - EvntOverflow 12 - VndrDevTstRcved
reserved15_12
Reserved, not used
event_info
Information about this event
reserved31_25
Reserved, not used
struct dwc3_event_gevt

Other Core Events

Definition

struct dwc3_event_gevt {
  u32 one_bit:1;
  u32 device_event:7;
  u32 phy_port_number:4;
  u32 reserved31_12:20;
};

Members

one_bit
indicates this is a non-endpoint event (not used)
device_event
indicates it’s (0x03) Carkit or (0x04) I2C event.
phy_port_number
self-explanatory
reserved31_12
Reserved, not used.
union dwc3_event

representation of Event Buffer contents

Definition

union dwc3_event {
  u32 raw;
  struct dwc3_event_type          type;
  struct dwc3_event_depevt        depevt;
  struct dwc3_event_devt          devt;
  struct dwc3_event_gevt          gevt;
};

Members

raw
raw 32-bit event
type
the type of the event
depevt
Device Endpoint Event
devt
Device Event
gevt
Global Event
struct dwc3_gadget_ep_cmd_params

representation of endpoint command parameters

Definition

struct dwc3_gadget_ep_cmd_params {
  u32 param2;
  u32 param1;
  u32 param0;
};

Members

param2
third parameter
param1
second parameter
param0
first parameter
struct dwc3_request * next_request(struct list_head * list)

gets the next request on the given list

Parameters

struct list_head * list
the request list to operate on

Description

Caller should take care of locking. This function return NULL or the first request available on list.

void dwc3_gadget_move_started_request(struct dwc3_request * req)

move req to the started_list

Parameters

struct dwc3_request * req
the request to be moved

Description

Caller should take care of locking. This function will move req from its current list to the endpoint’s started_list.

u32 dwc3_gadget_ep_get_transfer_index(struct dwc3_ep * dep)

Gets transfer index from HW

Parameters

struct dwc3_ep * dep
dwc3 endpoint

Description

Caller should take care of locking. Returns the transfer resource index for a given endpoint.

int dwc3_gadget_set_test_mode(struct dwc3 * dwc, int mode)

enables usb2 test modes

Parameters

struct dwc3 * dwc
pointer to our context structure
int mode
the mode to set (J, K SE0 NAK, Force Enable)

Description

Caller should take care of locking. This function will return 0 on success or -EINVAL if wrong Test Selector is passed.

gets current state of usb link

Parameters

struct dwc3 * dwc
pointer to our context structure

Description

Caller should take care of locking. This function will return the link state on success (>= 0) or -ETIMEDOUT.

sets usb link to a particular state

Parameters

struct dwc3 * dwc
pointer to our context structure
enum dwc3_link_state state
the state to put link into

Description

Caller should take care of locking. This function will return 0 on success or -ETIMEDOUT.

void dwc3_ep_inc_trb(u8 * index)

increment a trb index.

Parameters

u8 * index
Pointer to the TRB index to increment.

Description

The index should never point to the link TRB. After incrementing, if it is point to the link TRB, wrap around to the beginning. The link TRB is always at the last TRB entry.

void dwc3_ep_inc_enq(struct dwc3_ep * dep)

increment endpoint’s enqueue pointer

Parameters

struct dwc3_ep * dep
The endpoint whose enqueue pointer we’re incrementing
void dwc3_ep_inc_deq(struct dwc3_ep * dep)

increment endpoint’s dequeue pointer

Parameters

struct dwc3_ep * dep
The endpoint whose enqueue pointer we’re incrementing
void dwc3_gadget_giveback(struct dwc3_ep * dep, struct dwc3_request * req, int status)

call struct usb_request’s ->complete callback

Parameters

struct dwc3_ep * dep
The endpoint to whom the request belongs to
struct dwc3_request * req
The request we’re giving back
int status
completion code for the request

Description

Must be called with controller’s lock held and interrupts disabled. This function will unmap req and call its ->:c:func:complete() callback to notify upper layers that it has completed.

int dwc3_send_gadget_generic_command(struct dwc3 * dwc, unsigned cmd, u32 param)

issue a generic command for the controller

Parameters

struct dwc3 * dwc
pointer to the controller context
unsigned cmd
the command to be issued
u32 param
command parameter

Description

Caller should take care of locking. Issue cmd with a given param to dwc and wait for its completion.

int dwc3_send_gadget_ep_cmd(struct dwc3_ep * dep, unsigned cmd, struct dwc3_gadget_ep_cmd_params * params)

issue an endpoint command

Parameters

struct dwc3_ep * dep
the endpoint to which the command is going to be issued
unsigned cmd
the command to be issued
struct dwc3_gadget_ep_cmd_params * params
parameters to the command

Description

Caller should handle locking. This function will issue cmd with given params to dep and wait for its completion.

int dwc3_gadget_start_config(struct dwc3 * dwc, struct dwc3_ep * dep)

configure ep resources

Parameters

struct dwc3 * dwc
pointer to our controller context structure
struct dwc3_ep * dep
endpoint that is being enabled

Description

Issue a DWC3_DEPCMD_DEPSTARTCFG command to dep. After the command’s completion, it will set Transfer Resource for all available endpoints.

The assignment of transfer resources cannot perfectly follow the data book due to the fact that the controller driver does not have all knowledge of the configuration in advance. It is given this information piecemeal by the composite gadget framework after every SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DWC3_DEPCMD_DEPSTARTCFG for every USB_REQ_SET_CONFIGURATION and USB_REQ_SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple interfaces.

2) The databook does not mention doing more DWC3_DEPCMD_DEPXFERCFG for new endpoint on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this setting will stay persistent until either a core reset or hibernation. So whenever we do a DWC3_DEPCMD_DEPSTARTCFG``(0) we can go ahead and do ``DWC3_DEPCMD_DEPXFERCFG for every hardware endpoint as well. We are guaranteed that there are as many transfer resources as endpoints.

This function is called for each endpoint when it is being enabled but is triggered only when called for EP0-out, which always happens first, and which should only happen in one of the above conditions.

int __dwc3_gadget_ep_enable(struct dwc3_ep * dep, bool modify, bool restore)

initializes a hw endpoint

Parameters

struct dwc3_ep * dep
endpoint to be initialized
bool modify
if true, modify existing endpoint configuration
bool restore
if true, restore endpoint configuration from scratch buffer

Description

Caller should take care of locking. Execute all necessary commands to initialize a HW endpoint so it can be used by a gadget driver.

int __dwc3_gadget_ep_disable(struct dwc3_ep * dep)

disables a hw endpoint

Parameters

struct dwc3_ep * dep
the endpoint to disable

Description

This function undoes what __dwc3_gadget_ep_enable did and also removes requests which are currently being processed by the hardware and those which are not yet scheduled.

Caller should take care of locking.

void dwc3_prepare_one_trb(struct dwc3_ep * dep, struct dwc3_request * req, unsigned chain, unsigned node)

setup one TRB from one request

Parameters

struct dwc3_ep * dep
endpoint for which this request is prepared
struct dwc3_request * req
dwc3_request pointer
unsigned chain
should this TRB be chained to the next?
unsigned node
only for isochronous endpoints. First TRB needs different type.
struct dwc3_trb * dwc3_ep_prev_trb(struct dwc3_ep * dep, u8 index)

returns the previous TRB in the ring

Parameters

struct dwc3_ep * dep
The endpoint with the TRB ring
u8 index
The index of the current TRB in the ring

Description

Returns the TRB prior to the one pointed to by the index. If the index is 0, we will wrap backwards, skip the link TRB, and return the one just before that.

void dwc3_gadget_setup_nump(struct dwc3 * dwc)

calculate and initialize NUMP field of DWC3_DCFG

Parameters

struct dwc3 * dwc
pointer to our context structure

Description

The following looks like complex but it’s actually very simple. In order to calculate the number of packets we can burst at once on OUT transfers, we’re gonna use RxFIFO size.

To calculate RxFIFO size we need two numbers: MDWIDTH = size, in bits, of the internal memory bus RAM2_DEPTH = depth, in MDWIDTH, of internal RAM2 (where RxFIFO sits)

Given these two numbers, the formula is simple:

RxFIFO Size = (RAM2_DEPTH * MDWIDTH / 8) - 24 - 16;

24 bytes is for 3x SETUP packets 16 bytes is a clock domain crossing tolerance

Given RxFIFO Size, NUMP = RxFIFOSize / 1024;

int dwc3_gadget_init(struct dwc3 * dwc)

initializes gadget related registers

Parameters

struct dwc3 * dwc
pointer to our controller context structure

Description

Returns 0 on success otherwise negative errno.

DWC3_DEFAULT_AUTOSUSPEND_DELAY()

DesignWare USB3 DRD Controller Core file

Parameters

Description

Copyright (C) 2010-2011 Texas Instruments Incorporated - http://www.ti.com

Authors: Felipe Balbi <balbi**ti.com**>,
Sebastian Andrzej Siewior <bigeasy**linutronix.de**>
int dwc3_get_dr_mode(struct dwc3 * dwc)

Validates and sets dr_mode

Parameters

struct dwc3 * dwc
pointer to our context structure
int dwc3_core_soft_reset(struct dwc3 * dwc)

Issues core soft reset and PHY reset

Parameters

struct dwc3 * dwc
pointer to our context structure
void dwc3_free_one_event_buffer(struct dwc3 * dwc, struct dwc3_event_buffer * evt)

Frees one event buffer

Parameters

struct dwc3 * dwc
Pointer to our controller context structure
struct dwc3_event_buffer * evt
Pointer to event buffer to be freed
struct dwc3_event_buffer * dwc3_alloc_one_event_buffer(struct dwc3 * dwc, unsigned length)

Allocates one event buffer structure

Parameters

struct dwc3 * dwc
Pointer to our controller context structure
unsigned length
size of the event buffer

Description

Returns a pointer to the allocated event buffer structure on success otherwise ERR_PTR(errno).

void dwc3_free_event_buffers(struct dwc3 * dwc)

frees all allocated event buffers

Parameters

struct dwc3 * dwc
Pointer to our controller context structure
int dwc3_alloc_event_buffers(struct dwc3 * dwc, unsigned length)

Allocates num event buffers of size length

Parameters

struct dwc3 * dwc
pointer to our controller context structure
unsigned length
size of event buffer

Description

Returns 0 on success otherwise negative errno. In the error case, dwc may contain some buffers allocated but not all which were requested.

int dwc3_event_buffers_setup(struct dwc3 * dwc)

setup our allocated event buffers

Parameters

struct dwc3 * dwc
pointer to our controller context structure

Description

Returns 0 on success otherwise negative errno.

int dwc3_phy_setup(struct dwc3 * dwc)

Configure USB PHY Interface of DWC3 Core

Parameters

struct dwc3 * dwc
Pointer to our controller context structure

Description

Returns 0 on success. The USB PHY interfaces are configured but not initialized. The PHY interfaces and the PHYs get initialized together with the core in dwc3_core_init.

int dwc3_core_init(struct dwc3 * dwc)

Low-level initialization of DWC3 Core

Parameters

struct dwc3 * dwc
Pointer to our controller context structure

Description

Returns 0 on success otherwise negative errno.

[1](1, 2, 3) Transfer Request Block
[3](1, 2) The Debug File System
[4]The Config File System
[5]Command Block Wrapper