8.10. ioctl VIDIOC_ENCODER_CMD, VIDIOC_TRY_ENCODER_CMD

8.10.1. Name

VIDIOC_ENCODER_CMD - VIDIOC_TRY_ENCODER_CMD - Execute an encoder command

8.10.2. Synopsis

int ioctl(int fd, VIDIOC_ENCODER_CMD, struct v4l2_encoder_cmd *argp)
int ioctl(int fd, VIDIOC_TRY_ENCODER_CMD, struct v4l2_encoder_cmd *argp)

8.10.3. Arguments

fd
File descriptor returned by open().

argp

8.10.4. Description

These ioctls control an audio/video (usually MPEG-) encoder. VIDIOC_ENCODER_CMD sends a command to the encoder, VIDIOC_TRY_ENCODER_CMD can be used to try a command without actually executing it.

To send a command applications must initialize all fields of a struct v4l2_encoder_cmd and call VIDIOC_ENCODER_CMD or VIDIOC_TRY_ENCODER_CMD with a pointer to this structure.

The cmd field must contain the command code. The flags field is currently only used by the STOP command and contains one bit: If the V4L2_ENC_CMD_STOP_AT_GOP_END flag is set, encoding will continue until the end of the current Group Of Pictures, otherwise it will stop immediately.

A read() or VIDIOC_STREAMON call sends an implicit START command to the encoder if it has not been started yet. After a STOP command, read() calls will read the remaining data buffered by the driver. When the buffer is empty, read() will return zero and the next read() call will restart the encoder.

A close() or VIDIOC_STREAMOFF call of a streaming file descriptor sends an implicit immediate STOP to the encoder, and all buffered data is discarded.

These ioctls are optional, not all drivers may support them. They were introduced in Linux 2.6.21.

v4l2_encoder_cmd
struct v4l2_encoder_cmd
__u32 cmd The encoder command, see Encoder Commands.
__u32 flags Flags to go with the command, see Encoder Command Flags. If no flags are defined for this command, drivers and applications must set this field to zero.
__u32 data[8] Reserved for future extensions. Drivers and applications must set the array to zero.
Encoder Commands
V4L2_ENC_CMD_START 0 Start the encoder. When the encoder is already running or paused, this command does nothing. No flags are defined for this command.
V4L2_ENC_CMD_STOP 1 Stop the encoder. When the V4L2_ENC_CMD_STOP_AT_GOP_END flag is set, encoding will continue until the end of the current Group Of Pictures, otherwise encoding will stop immediately. When the encoder is already stopped, this command does nothing. mem2mem encoders will send a V4L2_EVENT_EOS event when the last frame has been encoded and all frames are ready to be dequeued and will set the V4L2_BUF_FLAG_LAST buffer flag on the last buffer of the capture queue to indicate there will be no new buffers produced to dequeue. This buffer may be empty, indicated by the driver setting the bytesused field to 0. Once the V4L2_BUF_FLAG_LAST flag was set, the VIDIOC_DQBUF ioctl will not block anymore, but return an EPIPE error code.
V4L2_ENC_CMD_PAUSE 2 Pause the encoder. When the encoder has not been started yet, the driver will return an EPERM error code. When the encoder is already paused, this command does nothing. No flags are defined for this command.
V4L2_ENC_CMD_RESUME 3 Resume encoding after a PAUSE command. When the encoder has not been started yet, the driver will return an EPERM error code. When the encoder is already running, this command does nothing. No flags are defined for this command.
Encoder Command Flags
V4L2_ENC_CMD_STOP_AT_GOP_END 0x0001 Stop encoding at the end of the current Group Of Pictures, rather than immediately.

8.10.5. Return Value

On success 0 is returned, on error -1 and the errno variable is set appropriately. The generic error codes are described at the Generic Error Codes chapter.

EINVAL
The cmd field is invalid.
EPERM
The application sent a PAUSE or RESUME command when the encoder was not running.