.. SPDX-License-Identifier: GPL-2.0+ ======================================================== Linux Driver for the Pensando(R) Ethernet adapter family ======================================================== Pensando Linux Ethernet driver. Copyright(c) 2019 Pensando Systems, Inc Contents ======== - Identifying the Adapter - Enabling the driver - Configuring the driver - Statistics - Support Identifying the Adapter ======================= To find if one or more Pensando PCI Ethernet devices are installed on the host, check for the PCI devices:: $ lspci -d 1dd8: b5:00.0 Ethernet controller: Device 1dd8:1002 b6:00.0 Ethernet controller: Device 1dd8:1002 If such devices are listed as above, then the ionic.ko driver should find and configure them for use. There should be log entries in the kernel messages such as these:: $ dmesg | grep ionic ionic 0000:b5:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link) ionic 0000:b5:00.0 enp181s0: renamed from eth0 ionic 0000:b5:00.0 enp181s0: Link up - 100 Gbps ionic 0000:b6:00.0: 126.016 Gb/s available PCIe bandwidth (8.0 GT/s PCIe x16 link) ionic 0000:b6:00.0 enp182s0: renamed from eth0 ionic 0000:b6:00.0 enp182s0: Link up - 100 Gbps Driver and firmware version information can be gathered with either of ethtool or devlink tools:: $ ethtool -i enp181s0 driver: ionic version: 5.7.0 firmware-version: 1.8.0-28 ... $ devlink dev info pci/0000:b5:00.0 pci/0000:b5:00.0: driver ionic serial_number FLM18420073 versions: fixed: asic.id 0x0 asic.rev 0x0 running: fw 1.8.0-28 See Documentation/networking/devlink/ionic.rst for more information on the devlink dev info data. Enabling the driver =================== The driver is enabled via the standard kernel configuration system, using the make command:: make oldconfig/menuconfig/etc. The driver is located in the menu structure at: -> Device Drivers -> Network device support (NETDEVICES [=y]) -> Ethernet driver support -> Pensando devices -> Pensando Ethernet IONIC Support Configuring the Driver ====================== MTU --- Jumbo frame support is available with a maximum size of 9194 bytes. Interrupt coalescing -------------------- Interrupt coalescing can be configured by changing the rx-usecs value with the "ethtool -C" command. The rx-usecs range is 0-190. The tx-usecs value reflects the rx-usecs value as they are tied together on the same interrupt. SR-IOV ------ Minimal SR-IOV support is currently offered and can be enabled by setting the sysfs 'sriov_numvfs' value, if supported by your particular firmware configuration. XDP --- Support for XDP includes the basics, plus Jumbo frames, Redirect and ndo_xmit. There is no current support for zero-copy sockets or HW offload. Statistics ========== Basic hardware stats -------------------- The commands ``netstat -i``, ``ip -s link show``, and ``ifconfig`` show a limited set of statistics taken directly from firmware. For example:: $ ip -s link show enp181s0 7: enp181s0: mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000 link/ether 00:ae:cd:00:07:68 brd ff:ff:ff:ff:ff:ff RX: bytes packets errors dropped overrun mcast 414 5 0 0 0 0 TX: bytes packets errors dropped carrier collsns 1384 18 0 0 0 0 ethtool -S ---------- The statistics shown from the ``ethtool -S`` command includes a combination of driver counters and firmware counters, including port and queue specific values. The driver values are counters computed by the driver, and the firmware values are gathered by the firmware from the port hardware and passed through the driver with no further interpretation. Driver port specific:: tx_packets: 12 tx_bytes: 964 rx_packets: 5 rx_bytes: 414 tx_tso: 0 tx_tso_bytes: 0 tx_csum_none: 12 tx_csum: 0 rx_csum_none: 0 rx_csum_complete: 3 rx_csum_error: 0 xdp_drop: 0 xdp_aborted: 0 xdp_pass: 0 xdp_tx: 0 xdp_redirect: 0 xdp_frames: 0 Driver queue specific:: tx_0_pkts: 3 tx_0_bytes: 294 tx_0_clean: 3 tx_0_dma_map_err: 0 tx_0_linearize: 0 tx_0_frags: 0 tx_0_tso: 0 tx_0_tso_bytes: 0 tx_0_hwstamp_valid: 0 tx_0_hwstamp_invalid: 0 tx_0_csum_none: 3 tx_0_csum: 0 tx_0_vlan_inserted: 0 tx_0_xdp_frames: 0 rx_0_pkts: 2 rx_0_bytes: 120 rx_0_dma_map_err: 0 rx_0_alloc_err: 0 rx_0_csum_none: 0 rx_0_csum_complete: 0 rx_0_csum_error: 0 rx_0_hwstamp_valid: 0 rx_0_hwstamp_invalid: 0 rx_0_dropped: 0 rx_0_vlan_stripped: 0 rx_0_xdp_drop: 0 rx_0_xdp_aborted: 0 rx_0_xdp_pass: 0 rx_0_xdp_tx: 0 rx_0_xdp_redirect: 0 Firmware port specific:: hw_tx_dropped: 0 hw_rx_dropped: 0 hw_rx_over_errors: 0 hw_rx_missed_errors: 0 hw_tx_aborted_errors: 0 frames_rx_ok: 15 frames_rx_all: 15 frames_rx_bad_fcs: 0 frames_rx_bad_all: 0 octets_rx_ok: 1290 octets_rx_all: 1290 frames_rx_unicast: 10 frames_rx_multicast: 5 frames_rx_broadcast: 0 frames_rx_pause: 0 frames_rx_bad_length: 0 frames_rx_undersized: 0 frames_rx_oversized: 0 frames_rx_fragments: 0 frames_rx_jabber: 0 frames_rx_pripause: 0 frames_rx_stomped_crc: 0 frames_rx_too_long: 0 frames_rx_vlan_good: 3 frames_rx_dropped: 0 frames_rx_less_than_64b: 0 frames_rx_64b: 4 frames_rx_65b_127b: 11 frames_rx_128b_255b: 0 frames_rx_256b_511b: 0 frames_rx_512b_1023b: 0 frames_rx_1024b_1518b: 0 frames_rx_1519b_2047b: 0 frames_rx_2048b_4095b: 0 frames_rx_4096b_8191b: 0 frames_rx_8192b_9215b: 0 frames_rx_other: 0 frames_tx_ok: 31 frames_tx_all: 31 frames_tx_bad: 0 octets_tx_ok: 2614 octets_tx_total: 2614 frames_tx_unicast: 8 frames_tx_multicast: 21 frames_tx_broadcast: 2 frames_tx_pause: 0 frames_tx_pripause: 0 frames_tx_vlan: 0 frames_tx_less_than_64b: 0 frames_tx_64b: 4 frames_tx_65b_127b: 27 frames_tx_128b_255b: 0 frames_tx_256b_511b: 0 frames_tx_512b_1023b: 0 frames_tx_1024b_1518b: 0 frames_tx_1519b_2047b: 0 frames_tx_2048b_4095b: 0 frames_tx_4096b_8191b: 0 frames_tx_8192b_9215b: 0 frames_tx_other: 0 frames_tx_pri_0: 0 frames_tx_pri_1: 0 frames_tx_pri_2: 0 frames_tx_pri_3: 0 frames_tx_pri_4: 0 frames_tx_pri_5: 0 frames_tx_pri_6: 0 frames_tx_pri_7: 0 frames_rx_pri_0: 0 frames_rx_pri_1: 0 frames_rx_pri_2: 0 frames_rx_pri_3: 0 frames_rx_pri_4: 0 frames_rx_pri_5: 0 frames_rx_pri_6: 0 frames_rx_pri_7: 0 tx_pripause_0_1us_count: 0 tx_pripause_1_1us_count: 0 tx_pripause_2_1us_count: 0 tx_pripause_3_1us_count: 0 tx_pripause_4_1us_count: 0 tx_pripause_5_1us_count: 0 tx_pripause_6_1us_count: 0 tx_pripause_7_1us_count: 0 rx_pripause_0_1us_count: 0 rx_pripause_1_1us_count: 0 rx_pripause_2_1us_count: 0 rx_pripause_3_1us_count: 0 rx_pripause_4_1us_count: 0 rx_pripause_5_1us_count: 0 rx_pripause_6_1us_count: 0 rx_pripause_7_1us_count: 0 rx_pause_1us_count: 0 frames_tx_truncated: 0 Support ======= For general Linux networking support, please use the netdev mailing list, which is monitored by Pensando personnel:: netdev@vger.kernel.org For more specific support needs, please use the Pensando driver support email:: drivers@pensando.io