.. SPDX-License-Identifier: GPL-2.0+ ================================================================= Linux Base Driver for the Intel(R) Ethernet Controller 800 Series ================================================================= Intel ice Linux driver. Copyright(c) 2018-2021 Intel Corporation. Contents ======== - Overview - Identifying Your Adapter - Important Notes - Additional Features & Configurations - Performance Optimization The associated Virtual Function (VF) driver for this driver is iavf. Driver information can be obtained using ethtool and lspci. For questions related to hardware requirements, refer to the documentation supplied with your Intel adapter. All hardware requirements listed apply to use with Linux. This driver supports XDP (Express Data Path) and AF_XDP zero-copy. Note that XDP is blocked for frame sizes larger than 3KB. Identifying Your Adapter ======================== For information on how to identify your adapter, and for the latest Intel network drivers, refer to the Intel Support website: https://www.intel.com/support Important Notes =============== Packet drops may occur under receive stress ------------------------------------------- Devices based on the Intel(R) Ethernet Controller 800 Series are designed to tolerate a limited amount of system latency during PCIe and DMA transactions. If these transactions take longer than the tolerated latency, it can impact the length of time the packets are buffered in the device and associated memory, which may result in dropped packets. These packets drops typically do not have a noticeable impact on throughput and performance under standard workloads. If these packet drops appear to affect your workload, the following may improve the situation: 1) Make sure that your system's physical memory is in a high-performance configuration, as recommended by the platform vendor. A common recommendation is for all channels to be populated with a single DIMM module. 2) In your system's BIOS/UEFI settings, select the "Performance" profile. 3) Your distribution may provide tools like "tuned," which can help tweak kernel settings to achieve better standard settings for different workloads. Configuring SR-IOV for improved network security ------------------------------------------------ In a virtualized environment, on Intel(R) Ethernet Network Adapters that support SR-IOV, the virtual function (VF) may be subject to malicious behavior. Software-generated layer two frames, like IEEE 802.3x (link flow control), IEEE 802.1Qbb (priority based flow-control), and others of this type, are not expected and can throttle traffic between the host and the virtual switch, reducing performance. To resolve this issue, and to ensure isolation from unintended traffic streams, configure all SR-IOV enabled ports for VLAN tagging from the administrative interface on the PF. This configuration allows unexpected, and potentially malicious, frames to be dropped. See "Configuring VLAN Tagging on SR-IOV Enabled Adapter Ports" later in this README for configuration instructions. Do not unload port driver if VF with active VM is bound to it ------------------------------------------------------------- Do not unload a port's driver if a Virtual Function (VF) with an active Virtual Machine (VM) is bound to it. Doing so will cause the port to appear to hang. Once the VM shuts down, or otherwise releases the VF, the command will complete. Additional Features and Configurations ====================================== ethtool ------- The driver utilizes the ethtool interface for driver configuration and diagnostics, as well as displaying statistical information. The latest ethtool version is required for this functionality. Download it at: https://kernel.org/pub/software/network/ethtool/ NOTE: The rx_bytes value of ethtool does not match the rx_bytes value of Netdev, due to the 4-byte CRC being stripped by the device. The difference between the two rx_bytes values will be 4 x the number of Rx packets. For example, if Rx packets are 10 and Netdev (software statistics) displays rx_bytes as "X", then ethtool (hardware statistics) will display rx_bytes as "X+40" (4 bytes CRC x 10 packets). Viewing Link Messages --------------------- Link messages will not be displayed to the console if the distribution is restricting system messages. In order to see network driver link messages on your console, set dmesg to eight by entering the following:: # dmesg -n 8 NOTE: This setting is not saved across reboots. Dynamic Device Personalization ------------------------------ Dynamic Device Personalization (DDP) allows you to change the packet processing pipeline of a device by applying a profile package to the device at runtime. Profiles can be used to, for example, add support for new protocols, change existing protocols, or change default settings. DDP profiles can also be rolled back without rebooting the system. The DDP package loads during device initialization. The driver looks for ``intel/ice/ddp/ice.pkg`` in your firmware root (typically ``/lib/firmware/`` or ``/lib/firmware/updates/``) and checks that it contains a valid DDP package file. NOTE: Your distribution should likely have provided the latest DDP file, but if ice.pkg is missing, you can find it in the linux-firmware repository or from intel.com. If the driver is unable to load the DDP package, the device will enter Safe Mode. Safe Mode disables advanced and performance features and supports only basic traffic and minimal functionality, such as updating the NVM or downloading a new driver or DDP package. Safe Mode only applies to the affected physical function and does not impact any other PFs. See the "Intel(R) Ethernet Adapters and Devices User Guide" for more details on DDP and Safe Mode. NOTES: - If you encounter issues with the DDP package file, you may need to download an updated driver or DDP package file. See the log messages for more information. - The ice.pkg file is a symbolic link to the default DDP package file. - You cannot update the DDP package if any PF drivers are already loaded. To overwrite a package, unload all PFs and then reload the driver with the new package. - Only the first loaded PF per device can download a package for that device. You can install specific DDP package files for different physical devices in the same system. To install a specific DDP package file: 1. Download the DDP package file you want for your device. 2. Rename the file ice-xxxxxxxxxxxxxxxx.pkg, where 'xxxxxxxxxxxxxxxx' is the unique 64-bit PCI Express device serial number (in hex) of the device you want the package downloaded on. The filename must include the complete serial number (including leading zeros) and be all lowercase. For example, if the 64-bit serial number is b887a3ffffca0568, then the file name would be ice-b887a3ffffca0568.pkg. To find the serial number from the PCI bus address, you can use the following command:: # lspci -vv -s af:00.0 | grep -i Serial Capabilities: [150 v1] Device Serial Number b8-87-a3-ff-ff-ca-05-68 You can use the following command to format the serial number without the dashes:: # lspci -vv -s af:00.0 | grep -i Serial | awk '{print $7}' | sed s/-//g b887a3ffffca0568 3. Copy the renamed DDP package file to ``/lib/firmware/updates/intel/ice/ddp/``. If the directory does not yet exist, create it before copying the file. 4. Unload all of the PFs on the device. 5. Reload the driver with the new package. NOTE: The presence of a device-specific DDP package file overrides the loading of the default DDP package file (ice.pkg). Intel(R) Ethernet Flow Director ------------------------------- The Intel Ethernet Flow Director performs the following tasks: - Directs receive packets according to their flows to different queues - Enables tight control on routing a flow in the platform - Matches flows and CPU cores for flow affinity NOTE: This driver supports the following flow types: - IPv4 - TCPv4 - UDPv4 - SCTPv4 - IPv6 - TCPv6 - UDPv6 - SCTPv6 Each flow type supports valid combinations of IP addresses (source or destination) and UDP/TCP/SCTP ports (source and destination). You can supply only a source IP address, a source IP address and a destination port, or any combination of one or more of these four parameters. NOTE: This driver allows you to filter traffic based on a user-defined flexible two-byte pattern and offset by using the ethtool user-def and mask fields. Only L3 and L4 flow types are supported for user-defined flexible filters. For a given flow type, you must clear all Intel Ethernet Flow Director filters before changing the input set (for that flow type). Flow Director Filters --------------------- Flow Director filters are used to direct traffic that matches specified characteristics. They are enabled through ethtool's ntuple interface. To enable or disable the Intel Ethernet Flow Director and these filters:: # ethtool -K ntuple NOTE: When you disable ntuple filters, all the user programmed filters are flushed from the driver cache and hardware. All needed filters must be re-added when ntuple is re-enabled. To display all of the active filters:: # ethtool -u To add a new filter:: # ethtool -U flow-type src-ip [m ] dst-ip [m ] src-port [m ] dst-port [m ] action Where: - the Ethernet device to program - can be ip4, tcp4, udp4, sctp4, ip6, tcp6, udp6, sctp6 - the IP address to match on - the IPv4 address to mask on NOTE: These filters use inverted masks. - the port number to match on - the 16-bit integer for masking NOTE: These filters use inverted masks. - the queue to direct traffic toward (-1 discards the matched traffic) To delete a filter:: # ethtool -U delete Where is the filter ID displayed when printing all the active filters, and may also have been specified using "loc " when adding the filter. EXAMPLES: To add a filter that directs packet to queue 2:: # ethtool -U flow-type tcp4 src-ip 192.168.10.1 dst-ip \ 192.168.10.2 src-port 2000 dst-port 2001 action 2 [loc 1] To set a filter using only the source and destination IP address:: # ethtool -U flow-type tcp4 src-ip 192.168.10.1 dst-ip \ 192.168.10.2 action 2 [loc 1] To set a filter based on a user-defined pattern and offset:: # ethtool -U flow-type tcp4 src-ip 192.168.10.1 dst-ip \ 192.168.10.2 user-def 0x4FFFF action 2 [loc 1] where the value of the user-def field contains the offset (4 bytes) and the pattern (0xffff). To match TCP traffic sent from 192.168.0.1, port 5300, directed to 192.168.0.5, port 80, and then send it to queue 7:: # ethtool -U enp130s0 flow-type tcp4 src-ip 192.168.0.1 dst-ip 192.168.0.5 src-port 5300 dst-port 80 action 7 To add a TCPv4 filter with a partial mask for a source IP subnet:: # ethtool -U flow-type tcp4 src-ip 192.168.0.0 m 0.255.255.255 dst-ip 192.168.5.12 src-port 12600 dst-port 31 action 12 NOTES: For each flow-type, the programmed filters must all have the same matching input set. For example, issuing the following two commands is acceptable:: # ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 # ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.5 src-port 55 action 10 Issuing the next two commands, however, is not acceptable, since the first specifies src-ip and the second specifies dst-ip:: # ethtool -U enp130s0 flow-type ip4 src-ip 192.168.0.1 src-port 5300 action 7 # ethtool -U enp130s0 flow-type ip4 dst-ip 192.168.0.5 src-port 55 action 10 The second command will fail with an error. You may program multiple filters with the same fields, using different values, but, on one device, you may not program two tcp4 filters with different matching fields. The ice driver does not support matching on a subportion of a field, thus partial mask fields are not supported. Flex Byte Flow Director Filters ------------------------------- The driver also supports matching user-defined data within the packet payload. This flexible data is specified using the "user-def" field of the ethtool command in the following way: .. table:: ============================== ============================ ``31 28 24 20 16`` ``15 12 8 4 0`` ``offset into packet payload`` ``2 bytes of flexible data`` ============================== ============================ For example, :: ... user-def 0x4FFFF ... tells the filter to look 4 bytes into the payload and match that value against 0xFFFF. The offset is based on the beginning of the payload, and not the beginning of the packet. Thus :: flow-type tcp4 ... user-def 0x8BEAF ... would match TCP/IPv4 packets which have the value 0xBEAF 8 bytes into the TCP/IPv4 payload. Note that ICMP headers are parsed as 4 bytes of header and 4 bytes of payload. Thus to match the first byte of the payload, you must actually add 4 bytes to the offset. Also note that ip4 filters match both ICMP frames as well as raw (unknown) ip4 frames, where the payload will be the L3 payload of the IP4 frame. The maximum offset is 64. The hardware will only read up to 64 bytes of data from the payload. The offset must be even because the flexible data is 2 bytes long and must be aligned to byte 0 of the packet payload. The user-defined flexible offset is also considered part of the input set and cannot be programmed separately for multiple filters of the same type. However, the flexible data is not part of the input set and multiple filters may use the same offset but match against different data. RSS Hash Flow ------------- Allows you to set the hash bytes per flow type and any combination of one or more options for Receive Side Scaling (RSS) hash byte configuration. :: # ethtool -N rx-flow-hash