========================== ALPS HID Touchpad Protocol ========================== Introduction ------------ Currently ALPS HID driver supports U1 Touchpad device. U1 device basic information. ========== ====== Vendor ID 0x044E Product ID 0x120B Version ID 0x0121 ========== ====== HID Descriptor -------------- ======= ==================== ===== ======================================= Byte Field Value Notes ======= ==================== ===== ======================================= 0 wHIDDescLength 001E Length of HID Descriptor : 30 bytes 2 bcdVersion 0100 Compliant with Version 1.00 4 wReportDescLength 00B2 Report Descriptor is 178 Bytes (0x00B2) 6 wReportDescRegister 0002 Identifier to read Report Descriptor 8 wInputRegister 0003 Identifier to read Input Report 10 wMaxInputLength 0053 Input Report is 80 Bytes + 2 12 wOutputRegister 0000 Identifier to read Output Report 14 wMaxOutputLength 0000 No Output Reports 16 wCommandRegister 0005 Identifier for Command Register 18 wDataRegister 0006 Identifier for Data Register 20 wVendorID 044E Vendor ID 0x044E 22 wProductID 120B Product ID 0x120B 24 wVersionID 0121 Version 01.21 26 RESERVED 0000 RESERVED ======= ==================== ===== ======================================= Report ID --------- ========== ================= ========================================= ReportID-1 (Input Reports) (HIDUsage-Mouse) for TP&SP ReportID-2 (Input Reports) (HIDUsage-keyboard) for TP ReportID-3 (Input Reports) (Vendor Usage: Max 10 finger data) for TP ReportID-4 (Input Reports) (Vendor Usage: ON bit data) for GP ReportID-5 (Feature Reports) Feature Reports ReportID-6 (Input Reports) (Vendor Usage: StickPointer data) for SP ReportID-7 (Feature Reports) Flash update (Bootloader) ========== ================= ========================================= Data pattern ------------ ===== ========== ===== ================= Case1 ReportID_1 TP/SP Relative/Relative Case2 ReportID_3 TP Absolute ReportID_6 SP Absolute ===== ========== ===== ================= Command Read/Write ------------------ To read/write to RAM, need to send a command to the device. The command format is as below. DataByte(SET_REPORT) ===== ====================== Byte1 Command Byte Byte2 Address - Byte 0 (LSB) Byte3 Address - Byte 1 Byte4 Address - Byte 2 Byte5 Address - Byte 3 (MSB) Byte6 Value Byte Byte7 Checksum ===== ====================== Command Byte is read=0xD1/write=0xD2. Address is read/write RAM address. Value Byte is writing data when you send the write commands. When you read RAM, there is no meaning. DataByte(GET_REPORT) ===== ====================== Byte1 Response Byte Byte2 Address - Byte 0 (LSB) Byte3 Address - Byte 1 Byte4 Address - Byte 2 Byte5 Address - Byte 3 (MSB) Byte6 Value Byte Byte7 Checksum ===== ====================== Read value is stored in Value Byte. Packet Format Touchpad data byte ------------------ ======= ======= ======= ======= ======= ======= ======= ======= ===== - b7 b6 b5 b4 b3 b2 b1 b0 ======= ======= ======= ======= ======= ======= ======= ======= ===== 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1 2 0 0 0 Fcv Fn3 Fn2 Fn1 Fn0 3 Xa0_7 Xa0_6 Xa0_5 Xa0_4 Xa0_3 Xa0_2 Xa0_1 Xa0_0 4 Xa0_15 Xa0_14 Xa0_13 Xa0_12 Xa0_11 Xa0_10 Xa0_9 Xa0_8 5 Ya0_7 Ya0_6 Ya0_5 Ya0_4 Ya0_3 Ya0_2 Ya0_1 Ya0_0 6 Ya0_15 Ya0_14 Ya0_13 Ya0_12 Ya0_11 Ya0_10 Ya0_9 Ya0_8 7 LFB0 Zs0_6 Zs0_5 Zs0_4 Zs0_3 Zs0_2 Zs0_1 Zs0_0 8 Xa1_7 Xa1_6 Xa1_5 Xa1_4 Xa1_3 Xa1_2 Xa1_1 Xa1_0 9 Xa1_15 Xa1_14 Xa1_13 Xa1_12 Xa1_11 Xa1_10 Xa1_9 Xa1_8 10 Ya1_7 Ya1_6 Ya1_5 Ya1_4 Ya1_3 Ya1_2 Ya1_1 Ya1_0 11 Ya1_15 Ya1_14 Ya1_13 Ya1_12 Ya1_11 Ya1_10 Ya1_9 Ya1_8 12 LFB1 Zs1_6 Zs1_5 Zs1_4 Zs1_3 Zs1_2 Zs1_1 Zs1_0 13 Xa2_7 Xa2_6 Xa2_5 Xa2_4 Xa2_3 Xa2_2 Xa2_1 Xa2_0 14 Xa2_15 Xa2_14 Xa2_13 Xa2_12 Xa2_11 Xa2_10 Xa2_9 Xa2_8 15 Ya2_7 Ya2_6 Ya2_5 Ya2_4 Ya2_3 Ya2_2 Ya2_1 Ya2_0 16 Ya2_15 Ya2_14 Ya2_13 Ya2_12 Ya2_11 Ya2_10 Ya2_9 Ya2_8 17 LFB2 Zs2_6 Zs2_5 Zs2_4 Zs2_3 Zs2_2 Zs2_1 Zs2_0 18 Xa3_7 Xa3_6 Xa3_5 Xa3_4 Xa3_3 Xa3_2 Xa3_1 Xa3_0 19 Xa3_15 Xa3_14 Xa3_13 Xa3_12 Xa3_11 Xa3_10 Xa3_9 Xa3_8 20 Ya3_7 Ya3_6 Ya3_5 Ya3_4 Ya3_3 Ya3_2 Ya3_1 Ya3_0 21 Ya3_15 Ya3_14 Ya3_13 Ya3_12 Ya3_11 Ya3_10 Ya3_9 Ya3_8 22 LFB3 Zs3_6 Zs3_5 Zs3_4 Zs3_3 Zs3_2 Zs3_1 Zs3_0 23 Xa4_7 Xa4_6 Xa4_5 Xa4_4 Xa4_3 Xa4_2 Xa4_1 Xa4_0 24 Xa4_15 Xa4_14 Xa4_13 Xa4_12 Xa4_11 Xa4_10 Xa4_9 Xa4_8 25 Ya4_7 Ya4_6 Ya4_5 Ya4_4 Ya4_3 Ya4_2 Ya4_1 Ya4_0 26 Ya4_15 Ya4_14 Ya4_13 Ya4_12 Ya4_11 Ya4_10 Ya4_9 Ya4_8 27 LFB4 Zs4_6 Zs4_5 Zs4_4 Zs4_3 Zs4_2 Zs4_1 Zs4_0 ======= ======= ======= ======= ======= ======= ======= ======= ===== SW1-SW6: SW ON/OFF status Xan_15-0(16bit): X Absolute data of the "n"th finger Yan_15-0(16bit): Y Absolute data of the "n"th finger Zsn_6-0(7bit): Operation area of the "n"th finger StickPointer data byte ---------------------- ======= ======= ======= ======= ======= ======= ======= ======= ===== - b7 b6 b5 b4 b3 b2 b1 b0 ======= ======= ======= ======= ======= ======= ======= ======= ===== Byte1 1 1 1 0 1 SW3 SW2 SW1 Byte2 X7 X6 X5 X4 X3 X2 X1 X0 Byte3 X15 X14 X13 X12 X11 X10 X9 X8 Byte4 Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 Byte5 Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8 Byte6 Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 Byte7 T&P Z14 Z13 Z12 Z11 Z10 Z9 Z8 ======= ======= ======= ======= ======= ======= ======= ======= ===== SW1-SW3: SW ON/OFF status Xn_15-0(16bit): X Absolute data Yn_15-0(16bit): Y Absolute data Zn_14-0(15bit): Z