€•¢oŒsphinx.addnodes”Œdocument”“”)”}”(Œ rawsource”Œ”Œchildren”]”(Œ translations”Œ LanguagesNode”“”)”}”(hhh]”(hŒ pending_xref”“”)”}”(hhh]”Œdocutils.nodes”ŒText”“”ŒChinese (Simplified)”…””}”Œparent”hsbaŒ attributes”}”(Œids”]”Œclasses”]”Œnames”]”Œdupnames”]”Œbackrefs”]”Œ refdomain”Œstd”Œreftype”Œdoc”Œ reftarget”Œ"/translations/zh_CN/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuŒtagname”hhh ubh)”}”(hhh]”hŒChinese (Traditional)”…””}”hh2sbah}”(h]”h ]”h"]”h$]”h&]”Œ refdomain”h)Œreftype”h+Œ reftarget”Œ"/translations/zh_TW/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuh1hhh ubh)”}”(hhh]”hŒItalian”…””}”hhFsbah}”(h]”h ]”h"]”h$]”h&]”Œ refdomain”h)Œreftype”h+Œ reftarget”Œ"/translations/it_IT/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuh1hhh ubh)”}”(hhh]”hŒJapanese”…””}”hhZsbah}”(h]”h ]”h"]”h$]”h&]”Œ refdomain”h)Œreftype”h+Œ reftarget”Œ"/translations/ja_JP/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuh1hhh ubh)”}”(hhh]”hŒKorean”…””}”hhnsbah}”(h]”h ]”h"]”h$]”h&]”Œ refdomain”h)Œreftype”h+Œ reftarget”Œ"/translations/ko_KR/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuh1hhh ubh)”}”(hhh]”hŒPortuguese (Brazilian)”…””}”hh‚sbah}”(h]”h ]”h"]”h$]”h&]”Œ refdomain”h)Œreftype”h+Œ reftarget”Œ"/translations/pt_BR/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuh1hhh ubh)”}”(hhh]”hŒSpanish”…””}”hh–sbah}”(h]”h ]”h"]”h$]”h&]”Œ refdomain”h)Œreftype”h+Œ reftarget”Œ"/translations/sp_SP/hwmon/f71882fg”Œmodname”NŒ classname”NŒ refexplicit”ˆuh1hhh ubeh}”(h]”h ]”h"]”h$]”h&]”Œcurrent_language”ŒEnglish”uh1h hhŒ _document”hŒsource”NŒline”NubhŒsection”“”)”}”(hhh]”(hŒtitle”“”)”}”(hŒKernel driver f71882fg”h]”hŒKernel driver f71882fg”…””}”(hh¼h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hºhh·h²hh³Œhj¶ubhÌ)”}”(hŒPrefix: 'f71889fg'”h]”hŒPrefix: ‘f71889fg’”…””}”(hjÈh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K@hj¶ubhÌ)”}”(hŒAAddresses scanned: none, address read from Super I/O config space”h]”hŒAAddresses scanned: none, address read from Super I/O config space”…””}”(hjÖh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KBhj¶ubhÌ)”}”(hŒ,Datasheet: Available from the Fintek website”h]”hŒ,Datasheet: Available from the Fintek website”…””}”(hjäh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KDhj¶ubeh}”(h]”h ]”h"]”h$]”h&]”uh1hæhhãubhç)”}”(hŒ¦Fintek F71889ED Prefix: 'f71889ed' Addresses scanned: none, address read from Super I/O config space Datasheet: Should become available on the Fintek website soon ”h]”(hÌ)”}”(hŒFintek F71889ED”h]”hŒFintek F71889ED”…””}”(hjüh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KFhjøubhÌ)”}”(hŒPrefix: 'f71889ed'”h]”hŒPrefix: ‘f71889ed’”…””}”(hj h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KHhjøubhÌ)”}”(hŒAAddresses scanned: none, address read from Super I/O config space”h]”hŒAAddresses scanned: none, address read from Super I/O config space”…””}”(hjh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KJhjøubhÌ)”}”(hŒ=Datasheet: Should become available on the Fintek website soon”h]”hŒ=Datasheet: Should become available on the Fintek website soon”…””}”(hj&h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KLhjøubeh}”(h]”h ]”h"]”h$]”h&]”uh1hæhhãubhç)”}”(hŒ¤Fintek F71889A Prefix: 'f71889a' Addresses scanned: none, address read from Super I/O config space Datasheet: Should become available on the Fintek website soon ”h]”(hÌ)”}”(hŒFintek F71889A”h]”hŒFintek F71889A”…””}”(hj>h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KNhj:ubhÌ)”}”(hŒPrefix: 'f71889a'”h]”hŒPrefix: ‘f71889a’”…””}”(hjLh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KPhj:ubhÌ)”}”(hŒAAddresses scanned: none, address read from Super I/O config space”h]”hŒAAddresses scanned: none, address read from Super I/O config space”…””}”(hjZh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KRhj:ubhÌ)”}”(hŒ=Datasheet: Should become available on the Fintek website soon”h]”hŒ=Datasheet: Should become available on the Fintek website soon”…””}”(hjhh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KThj:ubeh}”(h]”h ]”h"]”h$]”h&]”uh1hæhhãubhç)”}”(hŒxFintek F8000 Prefix: 'f8000' Addresses scanned: none, address read from Super I/O config space Datasheet: Not public ”h]”(hÌ)”}”(hŒ Fintek F8000”h]”hŒ Fintek F8000”…””}”(hj€h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KVhj|ubhÌ)”}”(hŒPrefix: 'f8000'”h]”hŒPrefix: ‘f8000’”…””}”(hjŽh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KXhj|ubhÌ)”}”(hŒAAddresses scanned: none, address read from Super I/O config space”h]”hŒAAddresses scanned: none, address read from Super I/O config space”…””}”(hjœh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KZhj|ubhÌ)”}”(hŒDatasheet: Not public”h]”hŒDatasheet: Not public”…””}”(hjªh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K\hj|ubeh}”(h]”h ]”h"]”h$]”h&]”uh1hæhhãubhç)”}”(hX$Fintek F81801U Prefix: 'f71889fg' Addresses scanned: none, address read from Super I/O config space Datasheet: Not public Note: This is the 64-pin variant of the F71889FG, they have the same device ID and are fully compatible as far as hardware monitoring is concerned. ”h]”(hÌ)”}”(hŒFintek F81801U”h]”hŒFintek F81801U”…””}”(hjÂh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K^hj¾ubhÌ)”}”(hŒPrefix: 'f71889fg'”h]”hŒPrefix: ‘f71889fg’”…””}”(hjÐh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K`hj¾ubhÌ)”}”(hŒAAddresses scanned: none, address read from Super I/O config space”h]”hŒAAddresses scanned: none, address read from Super I/O config space”…””}”(hjÞh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kbhj¾ubhÌ)”}”(hŒDatasheet: Not public”h]”hŒDatasheet: Not public”…””}”(hjìh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kdhj¾ubhŒdefinition_list”“”)”}”(hhh]”hŒdefinition_list_item”“”)”}”(hŒ”Note: This is the 64-pin variant of the F71889FG, they have the same device ID and are fully compatible as far as hardware monitoring is concerned. ”h]”(hŒterm”“”)”}”(hŒNote:”h]”hŒNote:”…””}”(hjh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1jh³hÊh´KihjubhŒ definition”“”)”}”(hhh]”hÌ)”}”(hŒThis is the 64-pin variant of the F71889FG, they have the same device ID and are fully compatible as far as hardware monitoring is concerned.”h]”hŒThis is the 64-pin variant of the F71889FG, they have the same device ID and are fully compatible as far as hardware monitoring is concerned.”…””}”(hjh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kghjubah}”(h]”h ]”h"]”h$]”h&]”uh1jhjubeh}”(h]”h ]”h"]”h$]”h&]”uh1jÿh³hÊh´Kihjüubah}”(h]”h ]”h"]”h$]”h&]”uh1júhj¾ubeh}”(h]”h ]”h"]”h$]”h&]”uh1hæhhãubhç)”}”(hŒ“Fintek F81865F Prefix: 'f81865f' Addresses scanned: none, address read from Super I/O config space Datasheet: Available from the Fintek website ”h]”(hÌ)”}”(hŒFintek F81865F”h]”hŒFintek F81865F”…””}”(hjDh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kkhj@ubhÌ)”}”(hŒPrefix: 'f81865f'”h]”hŒPrefix: ‘f81865f’”…””}”(hjRh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kmhj@ubhÌ)”}”(hŒAAddresses scanned: none, address read from Super I/O config space”h]”hŒAAddresses scanned: none, address read from Super I/O config space”…””}”(hj`h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kohj@ubhÌ)”}”(hŒ,Datasheet: Available from the Fintek website”h]”hŒ,Datasheet: Available from the Fintek website”…””}”(hjnh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kqhj@ubeh}”(h]”h ]”h"]”h$]”h&]”uh1hæhhãubeh}”(h]”h ]”h"]”h$]”h&]”Œbullet”Œ*”uh1háh³hÊh´KhhÝubah}”(h]”h ]”h"]”h$]”h&]”uh1hÛh³hÊh´Khh·h²hubhÌ)”}”(hŒ+Author: Hans de Goede ”h]”(hŒAuthor: Hans de Goede <”…””}”(hjh²hh³Nh´NubhŒ reference”“”)”}”(hŒhdegoede@redhat.com”h]”hŒhdegoede@redhat.com”…””}”(hjšh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”Œrefuri”Œmailto:hdegoede@redhat.com”uh1j˜hjubhŒ>”…””}”(hjh²hh³Nh´Nubeh}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kshh·h²hubh¶)”}”(hhh]”(h»)”}”(hŒ Description”h]”hŒ Description”…””}”(hj·h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hºhj´h²hh³hÊh´KwubhÌ)”}”(hŒ›Fintek F718xx/F8000 Super I/O chips include complete hardware monitoring capabilities. They can monitor up to 9 voltages, 4 fans and 3 temperature sensors.”h]”hŒ›Fintek F718xx/F8000 Super I/O chips include complete hardware monitoring capabilities. They can monitor up to 9 voltages, 4 fans and 3 temperature sensors.”…””}”(hjÅh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kyhj´h²hubhÌ)”}”(hŒ}These chips also have fan controlling features, using either DC or PWM, in three different modes (one manual, two automatic).”h]”hŒ}These chips also have fan controlling features, using either DC or PWM, in three different modes (one manual, two automatic).”…””}”(hjÓh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K}hj´h²hubhÌ)”}”(hŒQThe driver assumes that no more than one chip is present, which seems reasonable.”h]”hŒQThe driver assumes that no more than one chip is present, which seems reasonable.”…””}”(hjáh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K€hj´h²hubeh}”(h]”Œ description”ah ]”h"]”Œ description”ah$]”h&]”uh1hµhh·h²hh³hÊh´Kwubh¶)”}”(hhh]”(h»)”}”(hŒ Monitoring”h]”hŒ Monitoring”…””}”(hjúh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hºhj÷h²hh³hÊh´K…ubhÌ)”}”(hŒ‡The Voltage, Fan and Temperature Monitoring uses the standard sysfs interface as documented in sysfs-interface, without any exceptions.”h]”hŒ‡The Voltage, Fan and Temperature Monitoring uses the standard sysfs interface as documented in sysfs-interface, without any exceptions.”…””}”(hjh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K‡hj÷h²hubeh}”(h]”Œ monitoring”ah ]”h"]”Œ monitoring”ah$]”h&]”uh1hµhh·h²hh³hÊh´K…ubh¶)”}”(hhh]”(h»)”}”(hŒ Fan Control”h]”hŒ Fan Control”…””}”(hj!h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hºhjh²hh³hÊh´KŒubhÌ)”}”(hŒÕBoth PWM (pulse-width modulation) and DC fan speed control methods are supported. The right one to use depends on external circuitry on the motherboard, so the driver assumes that the BIOS set the method properly.”h]”hŒÕBoth PWM (pulse-width modulation) and DC fan speed control methods are supported. The right one to use depends on external circuitry on the motherboard, so the driver assumes that the BIOS set the method properly.”…””}”(hj/h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KŽhjh²hubhÌ)”}”(hX8Note that the lowest numbered temperature zone trip point corresponds to the border between the highest and one but highest temperature zones, and vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp to low temp! This is how things are implemented in the IC, and the driver mimics this.”h]”hX8Note that the lowest numbered temperature zone trip point corresponds to the border between the highest and one but highest temperature zones, and vica versa. So the temperature zone trip points 1-4 (or 1-2) go from high temp to low temp! This is how things are implemented in the IC, and the driver mimics this.”…””}”(hj=h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K“hjh²hubhÌ)”}”(hXThere are 2 modes to specify the speed of the fan, PWM duty cycle (or DC voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM mode where the actual RPM of the fan (as measured) is controlled and the speed gets specified as 0-100% of the fan#_full_speed file.”h]”hXThere are 2 modes to specify the speed of the fan, PWM duty cycle (or DC voltage) mode, where 0-100% duty cycle (0-100% of 12V) is specified. And RPM mode where the actual RPM of the fan (as measured) is controlled and the speed gets specified as 0-100% of the fan#_full_speed file.”…””}”(hjKh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K™hjh²hubhÌ)”}”(hXÉSince both modes work in a 0-100% (mapped to 0-255) scale, there isn't a whole lot of a difference when modifying fan control settings. The only important difference is that in RPM mode the 0-100% controls the fan speed between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs RPM mode, it will also set fan#_full_speed properly, if it does not then fan control will not work properly, unless you set a sane fan#_full_speed value yourself.”h]”hXËSince both modes work in a 0-100% (mapped to 0-255) scale, there isn’t a whole lot of a difference when modifying fan control settings. The only important difference is that in RPM mode the 0-100% controls the fan speed between 0-100% of fan#_full_speed. It is assumed that if the BIOS programs RPM mode, it will also set fan#_full_speed properly, if it does not then fan control will not work properly, unless you set a sane fan#_full_speed value yourself.”…””}”(hjYh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kžhjh²hubhÌ)”}”(hŒ«Switching between these modes requires re-initializing a whole bunch of registers, so the mode which the BIOS has set is kept. The mode is printed when loading the driver.”h]”hŒ«Switching between these modes requires re-initializing a whole bunch of registers, so the mode which the BIOS has set is kept. The mode is printed when loading the driver.”…””}”(hjgh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K¦hjh²hubhÌ)”}”(hXThree different fan control modes are supported; the mode number is written to the pwm#_enable file. Note that not all modes are supported on all chips, and some modes may only be available in RPM / PWM mode. Writing an unsupported mode will result in an invalid parameter error.”h]”hXThree different fan control modes are supported; the mode number is written to the pwm#_enable file. Note that not all modes are supported on all chips, and some modes may only be available in RPM / PWM mode. Writing an unsupported mode will result in an invalid parameter error.”…””}”(hjuh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´Kªhjh²hubhâ)”}”(hhh]”(hç)”}”(hŒÙ1: Manual mode You ask for a specific PWM duty cycle / DC voltage or a specific % of fan#_full_speed by writing to the pwm# file. This mode is only available on the F71858FG / F8000 if the fan channel is in RPM mode. ”h]”hÌ)”}”(hŒØ1: Manual mode You ask for a specific PWM duty cycle / DC voltage or a specific % of fan#_full_speed by writing to the pwm# file. This mode is only available on the F71858FG / F8000 if the fan channel is in RPM mode.”h]”hŒØ1: Manual mode You ask for a specific PWM duty cycle / DC voltage or a specific % of fan#_full_speed by writing to the pwm# file. This mode is only available on the F71858FG / F8000 if the fan channel is in RPM mode.”…””}”(hjŠh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K¯hj†ubah}”(h]”h ]”h"]”h$]”h&]”uh1hæhjƒh²hh³hÊh´Nubhç)”}”(hX…2: Normal auto mode You can define a number of temperature/fan speed trip points that specify the percentage at which the fan should run at each temperature, and which temperature sensor a fan should follow, using the standard sysfs interface. The number and type of trip points are chip dependent - see the available files in sysfs. Fan/PWM channel 3 of the F8000 is always in this mode! ”h]”hÌ)”}”(hX„2: Normal auto mode You can define a number of temperature/fan speed trip points that specify the percentage at which the fan should run at each temperature, and which temperature sensor a fan should follow, using the standard sysfs interface. The number and type of trip points are chip dependent - see the available files in sysfs. Fan/PWM channel 3 of the F8000 is always in this mode!”h]”hX„2: Normal auto mode You can define a number of temperature/fan speed trip points that specify the percentage at which the fan should run at each temperature, and which temperature sensor a fan should follow, using the standard sysfs interface. The number and type of trip points are chip dependent - see the available files in sysfs. Fan/PWM channel 3 of the F8000 is always in this mode!”…””}”(hj¢h²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K´hjžubah}”(h]”h ]”h"]”h$]”h&]”uh1hæhjƒh²hh³hÊh´Nubhç)”}”(hŒÅ3: Thermostat mode (Only available on the F8000 when in duty cycle mode) The fan speed is regulated to keep the temp the fan is mapped to between temp#_auto_point2_temp and temp#_auto_point3_temp. ”h]”hÌ)”}”(hŒÄ3: Thermostat mode (Only available on the F8000 when in duty cycle mode) The fan speed is regulated to keep the temp the fan is mapped to between temp#_auto_point2_temp and temp#_auto_point3_temp.”h]”hŒÄ3: Thermostat mode (Only available on the F8000 when in duty cycle mode) The fan speed is regulated to keep the temp the fan is mapped to between temp#_auto_point2_temp and temp#_auto_point3_temp.”…””}”(hjºh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´K¼hj¶ubah}”(h]”h ]”h"]”h$]”h&]”uh1hæhjƒh²hh³hÊh´Nubeh}”(h]”h ]”h"]”h$]”h&]”jˆj‰uh1háh³hÊh´K¯hjh²hubhÌ)”}”(hŒ`All of the automatic modes require that pwm1 corresponds to fan1, pwm2 to fan2 and pwm3 to fan3.”h]”hŒ`All of the automatic modes require that pwm1 corresponds to fan1, pwm2 to fan2 and pwm3 to fan3.”…””}”(hjÔh²hh³Nh´Nubah}”(h]”h ]”h"]”h$]”h&]”uh1hËh³hÊh´KÀhjh²hubeh}”(h]”Œ fan-control”ah ]”h"]”Œ fan control”ah$]”h&]”uh1hµhh·h²hh³hÊh´KŒubeh}”(h]”Œkernel-driver-f71882fg”ah ]”h"]”Œkernel driver f71882fg”ah$]”h&]”uh1hµhhh²hh³hÊh´Kubeh}”(h]”h ]”h"]”h$]”h&]”Œsource”hÊuh1hŒcurrent_source”NŒ current_line”NŒsettings”Œdocutils.frontend”ŒValues”“”)”}”(hºNŒ generator”NŒ datestamp”NŒ source_link”NŒ source_url”NŒ toc_backlinks”Œentry”Œfootnote_backlinks”KŒ sectnum_xform”KŒstrip_comments”NŒstrip_elements_with_classes”NŒ strip_classes”NŒ report_level”KŒ halt_level”KŒexit_status_level”KŒdebug”NŒwarning_stream”NŒ traceback”ˆŒinput_encoding”Œ utf-8-sig”Œinput_encoding_error_handler”Œstrict”Œoutput_encoding”Œutf-8”Œoutput_encoding_error_handler”jŒerror_encoding”Œutf-8”Œerror_encoding_error_handler”Œbackslashreplace”Œ language_code”Œen”Œrecord_dependencies”NŒconfig”NŒ id_prefix”hŒauto_id_prefix”Œid”Œ dump_settings”NŒdump_internals”NŒdump_transforms”NŒdump_pseudo_xml”NŒexpose_internals”NŒstrict_visitor”NŒ_disable_config”NŒ_source”hÊŒ _destination”NŒ _config_files”]”Œ7/var/lib/git/docbuild/linux/Documentation/docutils.conf”aŒfile_insertion_enabled”ˆŒ raw_enabled”KŒline_length_limit”M'Œpep_references”NŒ pep_base_url”Œhttps://peps.python.org/”Œpep_file_url_template”Œpep-%04d”Œrfc_references”NŒ rfc_base_url”Œ&https://datatracker.ietf.org/doc/html/”Œ tab_width”KŒtrim_footnote_reference_space”‰Œsyntax_highlight”Œlong”Œ smart_quotes”ˆŒsmartquotes_locales”]”Œcharacter_level_inline_markup”‰Œdoctitle_xform”‰Œ docinfo_xform”KŒsectsubtitle_xform”‰Œ image_loading”Œlink”Œembed_stylesheet”‰Œcloak_email_addresses”ˆŒsection_self_link”‰Œenv”NubŒreporter”NŒindirect_targets”]”Œsubstitution_defs”}”Œsubstitution_names”}”Œrefnames”}”Œrefids”}”Œnameids”}”(jïjìjôjñjjjçjäuŒ nametypes”}”(jï‰jô‰j‰jç‰uh}”(jìh·jñj´jj÷jäjuŒ footnote_refs”}”Œ citation_refs”}”Œ autofootnotes”]”Œautofootnote_refs”]”Œsymbol_footnotes”]”Œsymbol_footnote_refs”]”Œ footnotes”]”Œ citations”]”Œautofootnote_start”KŒsymbol_footnote_start”KŒ id_counter”Œ collections”ŒCounter”“”}”…”R”Œparse_messages”]”Œtransform_messages”]”Œ transformer”NŒ include_log”]”Œ decoration”Nh²hub.