# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/usb/spacemit,k1-dwc3.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: SpacemiT K1 SuperSpeed DWC3 USB SoC Controller

maintainers:
  - Ze Huang <huang.ze@linux.dev>

description: |
  The SpacemiT K1 embeds a DWC3 USB IP Core which supports Host functions
  for USB 3.0 and DRD for USB 2.0.

  Key features:
  - USB3.0 SuperSpeed and USB2.0 High/Full/Low-Speed support
  - Supports low-power modes (USB2.0 suspend, USB3.0 U1/U2/U3)
  - Internal DMA controller and flexible endpoint FIFO sizing

  Communication Interface:
  - Use of PIPE3 (125MHz) interface for USB3.0 PHY
  - Use of UTMI+ (30/60MHz) interface for USB2.0 PHY

allOf:
  - $ref: snps,dwc3-common.yaml#

properties:
  compatible:
    const: spacemit,k1-dwc3

  reg:
    maxItems: 1

  clocks:
    maxItems: 1

  clock-names:
    const: usbdrd30

  interrupts:
    maxItems: 1

  phys:
    items:
      - description: phandle to USB2/HS PHY
      - description: phandle to USB3/SS PHY

  phy-names:
    items:
      - const: usb2-phy
      - const: usb3-phy

  resets:
    items:
      - description: USB3.0 AHB reset
      - description: USB3.0 VCC reset
      - description: USB3.0 PHY reset

  reset-names:
    items:
      - const: ahb
      - const: vcc
      - const: phy

  reset-delay:
    $ref: /schemas/types.yaml#/definitions/uint32
    default: 2
    description: delay after reset sequence [us]

  vbus-supply:
    description: A phandle to the regulator supplying the VBUS voltage.

required:
  - compatible
  - reg
  - clocks
  - clock-names
  - interrupts
  - phys
  - phy-names
  - resets
  - reset-names

unevaluatedProperties: false

examples:
  - |
    usb@c0a00000 {
        compatible = "spacemit,k1-dwc3";
        reg = <0xc0a00000 0x10000>;
        clocks = <&syscon_apmu 16>;
        clock-names = "usbdrd30";
        interrupts = <125>;
        phys = <&usb2phy>, <&usb3phy>;
        phy-names = "usb2-phy", "usb3-phy";
        resets = <&syscon_apmu 8>,
                 <&syscon_apmu 9>,
                 <&syscon_apmu 10>;
        reset-names = "ahb", "vcc", "phy";
        reset-delay = <2>;
        vbus-supply = <&usb3_vbus>;
        #address-cells = <1>;
        #size-cells = <0>;

        hub_2_0: hub@1 {
            compatible = "usb2109,2817";
            reg = <1>;
            vdd-supply = <&usb3_vhub>;
            peer-hub = <&hub_3_0>;
            reset-gpios = <&gpio 3 28 1>;
        };

        hub_3_0: hub@2 {
            compatible = "usb2109,817";
            reg = <2>;
            vdd-supply = <&usb3_vhub>;
            peer-hub = <&hub_2_0>;
            reset-gpios = <&gpio 3 28 1>;
        };
    };