# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/pinctrl/qcom,sm8450-pinctrl.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Qualcomm Technologies, Inc. SM8450 TLMM block

maintainers:
  - Vinod Koul <vkoul@kernel.org>

description: |
  This binding describes the Top Level Mode Multiplexer (TLMM) block found
  in the SM8450 platform.

allOf:
  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#

properties:
  compatible:
    const: qcom,sm8450-tlmm

  reg:
    maxItems: 1

  interrupts: true
  interrupt-controller: true
  '#interrupt-cells': true
  gpio-controller: true

  gpio-reserved-ranges:
    minItems: 1
    maxItems: 105

  gpio-line-names:
    maxItems: 209

  '#gpio-cells': true
  gpio-ranges: true
  wakeup-parent: true

required:
  - compatible
  - reg

additionalProperties: false

patternProperties:
  '-state$':
    oneOf:
      - $ref: "#/$defs/qcom-sm8450-tlmm-state"
      - patternProperties:
          "-pins$":
            $ref: "#/$defs/qcom-sm8450-tlmm-state"
        additionalProperties: false

$defs:
  qcom-sm8450-tlmm-state:
    type: object
    description:
      Pinctrl node's client devices use subnodes for desired pin configuration.
      Client device subnodes use below standard properties.

    properties:
      pins:
        description:
          List of gpio pins affected by the properties specified in this
          subnode.
        items:
          oneOf:
            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|20[0-9])$"
            - enum: [ ufs_reset, sdc2_clk, sdc2_cmd, sdc2_data ]
        minItems: 1
        maxItems: 36

      function:
        description:
          Specify the alternative function to be configured for the specified
          pins.
        enum: [ aon_cam, atest_char, atest_usb, audio_ref, cam_mclk, cci_async,
                cci_i2c, cci_timer, cmu_rng, coex_uart1, coex_uart2, cri_trng,
                cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1,
                ddr_pxi2, ddr_pxi3, dp_hot, gcc_gp1, gcc_gp2, gcc_gp3,
                gpio, ibi_i3c, jitter_bist, mdp_vsync, mdp_vsync0, mdp_vsync1,
                mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, mi2s0_sck,
                mi2s0_ws, mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws,
                mss_grfc0, mss_grfc1, mss_grfc10, mss_grfc11, mss_grfc12,
                mss_grfc2, mss_grfc3, mss_grfc4, mss_grfc5, mss_grfc6,
                mss_grfc7, mss_grfc8, mss_grfc9, nav, pcie0_clkreqn,
                pcie1_clkreqn, phase_flag, pll_bist, pll_clk, pri_mi2s,
                prng_rosc, qdss_cti, qdss_gpio, qlink0_enable, qlink0_request,
                qlink0_wmss, qlink1_enable, qlink1_request, qlink1_wmss,
                qlink2_enable, qlink2_request, qlink2_wmss, qspi0, qspi1,
                qspi2, qspi3, qspi_clk, qspi_cs, qup0, qup1, qup10, qup11,
                qup12, qup13, qup14, qup15, qup16, qup17, qup18, qup19, qup2,
                qup20, qup21, qup3, qup4, qup5, qup6, qup7, qup8, qup9, qup_l4,
                qup_l5, qup_l6, sd_write, sdc40, sdc41, sdc42, sdc43, sdc4_clk,
                sdc4_cmd, sec_mi2s, tb_trig, tgu_ch0, tgu_ch1, tgu_ch2,
                tgu_ch3, tmess_prng0, tmess_prng1, tmess_prng2, tmess_prng3,
                tsense_pwm1, tsense_pwm2, uim0_clk, uim0_data, uim0_present,
                uim0_reset, uim1_clk, uim1_data, uim1_present, uim1_reset,
                usb2phy_ac, usb_phy, vfr_0, vfr_1, vsense_trigger ]

      bias-disable: true
      bias-pull-down: true
      bias-pull-up: true
      drive-strength: true
      input-enable: true
      output-high: true
      output-low: true

    required:
      - pins

    allOf:
      - $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state"
      - if:
          properties:
            pins:
              pattern: "^gpio([0-9]|[1-9][0-9]|1[0-9][0-9]|20[0-9])$"
        then:
          required:
            - function

    additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/arm-gic.h>
    pinctrl@f100000 {
        compatible = "qcom,sm8450-tlmm";
        reg = <0x0f100000 0x300000>;
        gpio-controller;
        #gpio-cells = <2>;
        gpio-ranges = <&tlmm 0 0 211>;
        interrupt-controller;
        #interrupt-cells = <2>;
        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;

        gpio-wo-state {
            pins = "gpio1";
            function = "gpio";
        };

        uart-w-state {
            rx-pins {
                pins = "gpio26";
                function = "qup7";
                bias-pull-up;
            };

            tx-pins {
                pins = "gpio27";
                function = "qup7";
                bias-disable;
            };
        };
    };
...