# SPDX-License-Identifier: GPL-2.0 %YAML 1.2 --- $id: http://devicetree.org/schemas/pci/marvell,kirkwood-pcie.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# title: Marvell EBU PCIe interfaces maintainers: - Thomas Petazzoni - Pali Rohár allOf: - $ref: /schemas/pci/pci-host-bridge.yaml# properties: compatible: enum: - marvell,armada-370-pcie - marvell,armada-xp-pcie - marvell,dove-pcie - marvell,kirkwood-pcie ranges: description: > The ranges describing the MMIO registers have the following layout: 0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s where: * r is a 32-bits value that gives the offset of the MMIO registers of this PCIe interface, from the base of the internal registers. * s is a 32-bits value that give the size of this MMIO registers area. This range entry translates the '0x82000000 0 r' PCI address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part of the internal register window (as identified by MBUS_ID(0xf0, 0x01)). The ranges describing the MBus windows have the following layout: 0x8t000000 s 0 MBUS_ID(w, a) 0 1 0 where: * t is the type of the MBus window (as defined by the standard PCI DT bindings), 1 for I/O and 2 for memory. * s is the PCI slot that corresponds to this PCIe interface * w is the 'target ID' value for the MBus window * a the 'attribute' value for the MBus window. Since the location and size of the different MBus windows is not fixed in hardware, and only determined in runtime, those ranges cover the full first 4 GB of the physical address space, and do not translate into a valid CPU address. msi-parent: maxItems: 1 patternProperties: '^pcie@': type: object allOf: - $ref: /schemas/pci/pci-bus-common.yaml# - $ref: /schemas/pci/pci-device.yaml# unevaluatedProperties: false properties: clocks: maxItems: 1 interrupts: minItems: 1 maxItems: 2 interrupt-names: minItems: 1 items: - const: intx - const: error reset-delay-us: default: 100000 description: todo marvell,pcie-port: $ref: /schemas/types.yaml#/definitions/uint32 maximum: 3 description: todo marvell,pcie-lane: $ref: /schemas/types.yaml#/definitions/uint32 maximum: 3 description: todo interrupt-controller: type: object additionalProperties: false properties: interrupt-controller: true '#interrupt-cells': const: 1 required: - assigned-addresses - clocks - interrupt-map - marvell,pcie-port unevaluatedProperties: false examples: - | #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) soc { #address-cells = <2>; #size-cells = <2>; pcie@f001000000000000 { compatible = "marvell,armada-xp-pcie"; device_type = "pci"; #address-cells = <3>; #size-cells = <2>; bus-range = <0x00 0xff>; msi-parent = <&mpic>; ranges = <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO */ 0x82000000 0x3 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */ 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */ 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; pcie@1,0 { device_type = "pci"; assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; reg = <0x0800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 0x81000000 0 0 0x81000000 0x1 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 58>; marvell,pcie-port = <0>; marvell,pcie-lane = <0>; num-lanes = <1>; /* low-active PERST# reset on GPIO 25 */ reset-gpios = <&gpio0 25 1>; /* wait 20ms for device settle after reset deassertion */ reset-delay-us = <20000>; clocks = <&gateclk 5>; }; pcie@2,0 { device_type = "pci"; assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; reg = <0x1000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 0x81000000 0 0 0x81000000 0x2 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 59>; marvell,pcie-port = <0>; marvell,pcie-lane = <1>; num-lanes = <1>; clocks = <&gateclk 6>; }; pcie@3,0 { device_type = "pci"; assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; reg = <0x1800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 0x81000000 0 0 0x81000000 0x3 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 60>; marvell,pcie-port = <0>; marvell,pcie-lane = <2>; num-lanes = <1>; clocks = <&gateclk 7>; }; pcie@4,0 { device_type = "pci"; assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; reg = <0x2000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 0x81000000 0 0 0x81000000 0x4 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 61>; marvell,pcie-port = <0>; marvell,pcie-lane = <3>; num-lanes = <1>; clocks = <&gateclk 8>; }; pcie@5,0 { device_type = "pci"; assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; reg = <0x2800 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 0x81000000 0 0 0x81000000 0x5 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 62>; marvell,pcie-port = <1>; marvell,pcie-lane = <0>; num-lanes = <1>; clocks = <&gateclk 9>; }; pcie@6,0 { device_type = "pci"; assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; reg = <0x3000 0 0 0 0>; #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 0x81000000 0 0 0x81000000 0x6 0 1 0>; interrupt-map-mask = <0 0 0 0>; interrupt-map = <0 0 0 0 &mpic 63>; marvell,pcie-port = <1>; marvell,pcie-lane = <1>; num-lanes = <1>; clocks = <&gateclk 10>; }; }; }; ...