Device tree bindings for MVEBU Device Bus controllers The Device Bus controller available in some Marvell's SoC allows to control different types of standard memory and I/O devices such as NOR, NAND, and FPGA. The actual devices are instantiated from the child nodes of a Device Bus node. Required properties: - compatible: Armada 370/XP SoC are supported using the "marvell,mvebu-devbus" compatible string. Orion5x SoC are supported using the "marvell,orion-devbus" compatible string. - reg: A resource specifier for the register space. This is the base address of a chip select within the controller's register space. (see the example below) - #address-cells: Must be set to 1 - #size-cells: Must be set to 1 - ranges: Must be set up to reflect the memory layout with four integer values for each chip-select line in use: 0 Optional properties: - devbus,keep-config This property can optionally be used to keep using the timing parameters set by the bootloader. It makes all the timing properties described below unused. Timing properties for child nodes: Read parameters: - devbus,turn-off-ps: Defines the time during which the controller does not drive the AD bus after the completion of a device read. This prevents contentions on the Device Bus after a read cycle from a slow device. Mandatory, except if devbus,keep-config is used. - devbus,bus-width: Defines the bus width, in bits (e.g. <16>). Mandatory, except if devbus,keep-config is used. - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle, to read data sample. This parameter is useful for synchronous pipelined devices, where the address precedes the read data by one or two cycles. Mandatory, except if devbus,keep-config is used. - devbus,acc-first-ps: Defines the time delay from the negation of ALE[0] to the cycle that the first read data is sampled by the controller. Mandatory, except if devbus,keep-config is used. - devbus,acc-next-ps: Defines the time delay between the cycle that samples data N and the cycle that samples data N+1 (in burst accesses). Mandatory, except if devbus,keep-config is used. - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to DEV_OEn assertion. If set to 0 (default), DEV_OEn and DEV_CSn are asserted at the same cycle. This parameter has no affect on parameter (no affect on first data sample). Set to a value smaller than . Mandatory for "marvell,mvebu-devbus" compatible string, except if devbus,keep-config is used. - devbus,rd-hold-ps: Defines the time between the last data sample to the de-assertion of DEV_CSn. If set to 0 (default), DEV_OEn and DEV_CSn are de-asserted at the same cycle (the cycle of the last data sample). This parameter has no affect on DEV_OEn de-assertion. DEV_OEn is always de-asserted the next cycle after last data sampled. Also this parameter has no affect on parameter. Set to a value smaller than . Mandatory for "marvell,mvebu-devbus" compatible string, except if devbus,keep-config is used. Write parameters: - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle to the DEV_WEn assertion. Mandatory. - devbus,wr-low-ps: Defines the time during which DEV_WEn is active. A[2:0] and Data are kept valid as long as DEV_WEn is active. This parameter defines the setup time of address and data to DEV_WEn rise. Mandatory. - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept inactive (high) between data beats of a burst write. DEV_A[2:0] and Data are kept valid (do not toggle) for - ps. This parameter defines the hold time of address and data after DEV_WEn rise. Mandatory. - devbus,sync-enable: Synchronous device enable. 1: True 0: False Mandatory for "marvell,mvebu-devbus" compatible string, except if devbus,keep-config is used. An example for an Armada XP GP board, with a 16 MiB NOR device as child is showed below. Note that the Device Bus driver is in charge of allocating the mbus address decoding window for each of its child devices. The window is created using the chip select specified in the child device node together with the base address and size specified in the ranges property. For instance, in the example below the allocated decoding window will start at base address 0xf0000000, with a size 0x1000000 (16 MiB) for chip select 0 (a.k.a DEV_BOOTCS). This address window handling is done in this mvebu-devbus only as a temporary solution. It will be removed when the support for mbus device tree binding is added. The reg property implicitly specifies the chip select as this: 0x10400: DEV_BOOTCS 0x10408: DEV_CS0 0x10410: DEV_CS1 0x10418: DEV_CS2 0x10420: DEV_CS3 Example: devbus-bootcs@d0010400 { ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf0000000, size 0x1000000 */ #address-cells = <1>; #size-cells = <1>; /* Device Bus parameters are required */ /* Read parameters */ devbus,bus-width = <8>; devbus,turn-off-ps = <60000>; devbus,badr-skew-ps = <0>; devbus,acc-first-ps = <124000>; devbus,acc-next-ps = <248000>; devbus,rd-setup-ps = <0>; devbus,rd-hold-ps = <0>; /* Write parameters */ devbus,sync-enable = <0>; devbus,wr-high-ps = <60000>; devbus,wr-low-ps = <60000>; devbus,ale-wr-ps = <60000>; flash@0 { compatible = "cfi-flash"; /* 16 MiB */ reg = <0 0x1000000>; bank-width = <2>; #address-cells = <1>; #size-cells = <1>; /* * We split the 16 MiB in two partitions, * just as an example. */ partition@0 { label = "First"; reg = <0 0x800000>; }; partition@800000 { label = "Second"; reg = <0x800000 0x800000>; }; }; };