SEC 6 is as Freescale's Cryptographic Accelerator and Assurance Module (CAAM). Currently Freescale powerpc chip C29X is embedded with SEC 6. SEC 6 device tree binding include: -SEC 6 Node -Job Ring Node -Full Example ===================================================================== SEC 6 Node Description Node defines the base address of the SEC 6 block. This block specifies the address range of all global configuration registers for the SEC 6 block. For example, In C293, we could see three SEC 6 node. PROPERTIES - compatible Usage: required Value type: Definition: Must include "fsl,sec-v6.0". - fsl,sec-era Usage: optional Value type: Definition: A standard property. Define the 'ERA' of the SEC device. - #address-cells Usage: required Value type: Definition: A standard property. Defines the number of cells for representing physical addresses in child nodes. - #size-cells Usage: required Value type: Definition: A standard property. Defines the number of cells for representing the size of physical addresses in child nodes. - reg Usage: required Value type: Definition: A standard property. Specifies the physical address and length of the SEC 6 configuration registers. - ranges Usage: required Value type: Definition: A standard property. Specifies the physical address range of the SEC 6.0 register space (-SNVS not included). A triplet that includes the child address, parent address, & length. Note: All other standard properties (see the Devicetree Specification) are allowed but are optional. EXAMPLE crypto@a0000 { compatible = "fsl,sec-v6.0"; fsl,sec-era = <6>; #address-cells = <1>; #size-cells = <1>; reg = <0xa0000 0x20000>; ranges = <0 0xa0000 0x20000>; }; ===================================================================== Job Ring (JR) Node Child of the crypto node defines data processing interface to SEC 6 across the peripheral bus for purposes of processing cryptographic descriptors. The specified address range can be made visible to one (or more) cores. The interrupt defined for this node is controlled within the address range of this node. - compatible Usage: required Value type: Definition: Must include "fsl,sec-v6.0-job-ring". - reg Usage: required Value type: Definition: Specifies a two JR parameters: an offset from the parent physical address and the length the JR registers. - interrupts Usage: required Value type: Definition: Specifies the interrupts generated by this device. The value of the interrupts property consists of one interrupt specifier. The format of the specifier is defined by the binding document describing the node's interrupt parent. EXAMPLE jr@1000 { compatible = "fsl,sec-v6.0-job-ring"; reg = <0x1000 0x1000>; interrupts = <49 2 0 0>; }; =================================================================== Full Example Since some chips may contain more than one SEC, the dtsi contains only the node contents, not the node itself. A chip using the SEC should include the dtsi inside each SEC node. Example: In qoriq-sec6.0.dtsi: compatible = "fsl,sec-v6.0"; fsl,sec-era = <6>; #address-cells = <1>; #size-cells = <1>; jr@1000 { compatible = "fsl,sec-v6.0-job-ring", "fsl,sec-v5.2-job-ring", "fsl,sec-v5.0-job-ring", "fsl,sec-v4.4-job-ring", "fsl,sec-v4.0-job-ring"; reg = <0x1000 0x1000>; }; jr@2000 { compatible = "fsl,sec-v6.0-job-ring", "fsl,sec-v5.2-job-ring", "fsl,sec-v5.0-job-ring", "fsl,sec-v4.4-job-ring", "fsl,sec-v4.0-job-ring"; reg = <0x2000 0x1000>; }; In the C293 device tree, we add the include of public property: crypto@a0000 { /include/ "qoriq-sec6.0.dtsi" } crypto@a0000 { reg = <0xa0000 0x20000>; ranges = <0 0xa0000 0x20000>; jr@1000 { interrupts = <49 2 0 0>; }; jr@2000 { interrupts = <50 2 0 0>; }; };