From e3ad1c23ba72214669b364c6fa304531dc768c3e Mon Sep 17 00:00:00 2001 From: Pete Popov Date: Tue, 1 Mar 2005 06:33:16 +0000 Subject: Base Au1200 2.6 support. Signed-off-by: Ralf Baechle --- arch/mips/Kconfig | 18 + arch/mips/Makefile | 14 + arch/mips/au1000/common/au1xxx_irqmap.c | 32 +- arch/mips/au1000/common/cputable.c | 3 +- arch/mips/au1000/common/dbdma.c | 298 +++++++++++---- arch/mips/au1000/common/irq.c | 4 +- arch/mips/au1000/common/usbdev.c | 12 +- arch/mips/au1000/pb1200/Makefile | 5 + arch/mips/au1000/pb1200/board_setup.c | 187 ++++++++++ arch/mips/au1000/pb1200/init.c | 69 ++++ arch/mips/au1000/pb1200/irqmap.c | 180 +++++++++ arch/mips/kernel/cpu-probe.c | 5 + arch/mips/kernel/proc.c | 3 + arch/mips/mm/c-r4k.c | 4 + arch/mips/mm/tlbex.c | 1 + include/asm-mips/bootinfo.h | 2 + include/asm-mips/cpu.h | 3 +- include/asm-mips/mach-au1x00/au1000.h | 556 +++++++++++++++++++++++++--- include/asm-mips/mach-au1x00/au1xxx_dbdma.h | 124 ++++++- include/asm-mips/mach-db1x00/db1200.h | 214 +++++++++++ include/asm-mips/mach-pb1x00/pb1200.h | 244 ++++++++++++ 21 files changed, 1796 insertions(+), 182 deletions(-) create mode 100644 arch/mips/au1000/pb1200/Makefile create mode 100644 arch/mips/au1000/pb1200/board_setup.c create mode 100644 arch/mips/au1000/pb1200/init.c create mode 100644 arch/mips/au1000/pb1200/irqmap.c create mode 100644 include/asm-mips/mach-db1x00/db1200.h create mode 100644 include/asm-mips/mach-pb1x00/pb1200.h diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index 2edbef5f3551a..455de42db7c92 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -642,6 +642,10 @@ config SGI_IP32 help If you want this kernel to run on SGI O2 workstation, say Y here. +config SOC_AU1200 + bool + select SOC_AU1X00 + config SOC_AU1X00 bool "Support for AMD/Alchemy Au1X00 SOCs" select SYS_SUPPORTS_32BIT_KERNEL @@ -702,6 +706,13 @@ config MIPS_PB1550 select HW_HAS_PCI select MIPS_DISABLE_OBSOLETE_IDE +config MIPS_PB1200 + bool "AMD Alchemy PB1200 board" + select SOC_AU1200 + select DMA_NONCOHERENT + select MIPS_DISABLE_OBSOLETE_IDE + select SYS_SUPPORTS_LITTLE_ENDIAN + config MIPS_DB1000 bool "DB1000 board" depends on SOC_AU1000 @@ -732,6 +743,13 @@ config MIPS_BOSPORUS depends on SOC_AU1500 select DMA_NONCOHERENT +config MIPS_DB1200 + bool "AMD Alchemy DB1200 board" + select SOC_AU1200 + select DMA_NONCOHERENT + select MIPS_DISABLE_OBSOLETE_IDE + select SYS_SUPPORTS_LITTLE_ENDIAN + config MIPS_MIRAGE bool "Mirage board" depends on SOC_AU1500 diff --git a/arch/mips/Makefile b/arch/mips/Makefile index 5f2dfcddb9f2f..99da8a2850c7b 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -265,6 +265,13 @@ libs-$(CONFIG_MIPS_PB1550) += arch/mips/au1000/pb1550/ cflags-$(CONFIG_MIPS_PB1550) += -Iinclude/asm-mips/mach-pb1x00 load-$(CONFIG_MIPS_PB1550) += 0xffffffff80100000 +# +# AMD Alchemy Pb1200 eval board +# +libs-$(CONFIG_MIPS_PB1200) += arch/mips/au1000/pb1200/ +cflags-$(CONFIG_MIPS_PB1200) += -Iinclude/asm-mips/mach-pb1x00 +load-$(CONFIG_MIPS_PB1200) += 0xffffffff80100000 + # # AMD Alchemy Db1000 eval board # @@ -293,6 +300,13 @@ libs-$(CONFIG_MIPS_DB1550) += arch/mips/au1000/db1x00/ cflags-$(CONFIG_MIPS_DB1550) += -Iinclude/asm-mips/mach-db1x00 load-$(CONFIG_MIPS_DB1550) += 0xffffffff80100000 +# +# AMD Alchemy Db1200 eval board +# +libs-$(CONFIG_MIPS_DB1200) += arch/mips/au1000/pb1200/ +cflags-$(CONFIG_MIPS_DB1200) += -Iinclude/asm-mips/mach-db1x00 +load-$(CONFIG_MIPS_DB1200) += 0xffffffff80100000 + # # AMD Alchemy Bosporus eval board # diff --git a/arch/mips/au1000/common/au1xxx_irqmap.c b/arch/mips/au1000/common/au1xxx_irqmap.c index 8a0f39f67c597..0b2c03c523198 100644 --- a/arch/mips/au1000/common/au1xxx_irqmap.c +++ b/arch/mips/au1000/common/au1xxx_irqmap.c @@ -173,14 +173,14 @@ au1xxx_irq_map_t au1xxx_ic0_map[] = { { AU1550_PSC1_INT, INTC_INT_HIGH_LEVEL, 0}, { AU1550_PSC2_INT, INTC_INT_HIGH_LEVEL, 0}, { AU1550_PSC3_INT, INTC_INT_HIGH_LEVEL, 0}, - { AU1550_TOY_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1550_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1550_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1550_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 }, - { AU1550_RTC_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1550_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1550_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1550_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 }, + { AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 }, { AU1550_NAND_INT, INTC_INT_RISE_EDGE, 0}, { AU1550_USB_DEV_REQ_INT, INTC_INT_HIGH_LEVEL, 0 }, { AU1550_USB_DEV_SUS_INT, INTC_INT_RISE_EDGE, 0 }, @@ -201,14 +201,14 @@ au1xxx_irq_map_t au1xxx_ic0_map[] = { { AU1200_PSC1_INT, INTC_INT_HIGH_LEVEL, 0}, { AU1200_AES_INT, INTC_INT_HIGH_LEVEL, 0}, { AU1200_CAMERA_INT, INTC_INT_HIGH_LEVEL, 0}, - { AU1200_TOY_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1200_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1200_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1200_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 }, - { AU1200_RTC_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1200_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1200_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, - { AU1200_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_TOY_MATCH2_INT, INTC_INT_RISE_EDGE, 1 }, + { AU1000_RTC_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_RTC_MATCH0_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_RTC_MATCH1_INT, INTC_INT_RISE_EDGE, 0 }, + { AU1000_RTC_MATCH2_INT, INTC_INT_RISE_EDGE, 0 }, { AU1200_NAND_INT, INTC_INT_RISE_EDGE, 0}, { AU1200_USB_INT, INTC_INT_HIGH_LEVEL, 0 }, { AU1200_LCD_INT, INTC_INT_HIGH_LEVEL, 0}, diff --git a/arch/mips/au1000/common/cputable.c b/arch/mips/au1000/common/cputable.c index f5521dfccfd61..4dbde82c82153 100644 --- a/arch/mips/au1000/common/cputable.c +++ b/arch/mips/au1000/common/cputable.c @@ -37,7 +37,8 @@ struct cpu_spec cpu_specs[] = { { 0xffffffff, 0x02030203, "Au1100 BD", 0, 1 }, { 0xffffffff, 0x02030204, "Au1100 BE", 0, 1 }, { 0xffffffff, 0x03030200, "Au1550 AA", 0, 1 }, - { 0xffffffff, 0x04030200, "Au1200 AA", 0, 1 }, + { 0xffffffff, 0x04030200, "Au1200 AB", 0, 0 }, + { 0xffffffff, 0x04030201, "Au1200 AC", 0, 1 }, { 0x00000000, 0x00000000, "Unknown Au1xxx", 1, 0 }, }; diff --git a/arch/mips/au1000/common/dbdma.c b/arch/mips/au1000/common/dbdma.c index adfc3172aace5..cf10dc246f82a 100644 --- a/arch/mips/au1000/common/dbdma.c +++ b/arch/mips/au1000/common/dbdma.c @@ -29,6 +29,7 @@ * 675 Mass Ave, Cambridge, MA 02139, USA. * */ + #include #include #include @@ -42,6 +43,8 @@ #include #include +/* #include */ + #if defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) /* @@ -55,43 +58,16 @@ * functions. The drivers allocate the data buffers and assign them * to the descriptors. */ -static DEFINE_SPINLOCK(au1xxx_dbdma_spin_lock); +static spinlock_t au1xxx_dbdma_spin_lock = SPIN_LOCK_UNLOCKED; /* I couldn't find a macro that did this...... */ #define ALIGN_ADDR(x, a) ((((u32)(x)) + (a-1)) & ~(a-1)) -static volatile dbdma_global_t *dbdma_gptr = (dbdma_global_t *)DDMA_GLOBAL_BASE; -static int dbdma_initialized; +static dbdma_global_t *dbdma_gptr = (dbdma_global_t *)DDMA_GLOBAL_BASE; +static int dbdma_initialized=0; static void au1xxx_dbdma_init(void); -typedef struct dbdma_device_table { - u32 dev_id; - u32 dev_flags; - u32 dev_tsize; - u32 dev_devwidth; - u32 dev_physaddr; /* If FIFO */ - u32 dev_intlevel; - u32 dev_intpolarity; -} dbdev_tab_t; - -typedef struct dbdma_chan_config { - u32 chan_flags; - u32 chan_index; - dbdev_tab_t *chan_src; - dbdev_tab_t *chan_dest; - au1x_dma_chan_t *chan_ptr; - au1x_ddma_desc_t *chan_desc_base; - au1x_ddma_desc_t *get_ptr, *put_ptr, *cur_ptr; - void *chan_callparam; - void (*chan_callback)(int, void *, struct pt_regs *); -} chan_tab_t; - -#define DEV_FLAGS_INUSE (1 << 0) -#define DEV_FLAGS_ANYUSE (1 << 1) -#define DEV_FLAGS_OUT (1 << 2) -#define DEV_FLAGS_IN (1 << 3) - static dbdev_tab_t dbdev_tab[] = { #ifdef CONFIG_SOC_AU1550 /* UARTS */ @@ -157,13 +133,13 @@ static dbdev_tab_t dbdev_tab[] = { { DSCR_CMD0_MAE_BOTH, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, { DSCR_CMD0_LCD, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, + { DSCR_CMD0_SDMS_TX0, DEV_FLAGS_OUT, 4, 8, 0x10600000, 0, 0 }, + { DSCR_CMD0_SDMS_RX0, DEV_FLAGS_IN, 4, 8, 0x10600004, 0, 0 }, + { DSCR_CMD0_SDMS_TX1, DEV_FLAGS_OUT, 4, 8, 0x10680000, 0, 0 }, + { DSCR_CMD0_SDMS_RX1, DEV_FLAGS_IN, 4, 8, 0x10680004, 0, 0 }, - { DSCR_CMD0_AES_TX, DEV_FLAGS_OUT, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_AES_RX, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, + { DSCR_CMD0_AES_RX, DEV_FLAGS_IN , 4, 32, 0x10300008, 0, 0 }, + { DSCR_CMD0_AES_TX, DEV_FLAGS_OUT, 4, 32, 0x10300004, 0, 0 }, { DSCR_CMD0_PSC0_TX, DEV_FLAGS_OUT, 0, 0, 0x11a0001c, 0, 0 }, { DSCR_CMD0_PSC0_RX, DEV_FLAGS_IN, 0, 0, 0x11a0001c, 0, 0 }, @@ -173,9 +149,9 @@ static dbdev_tab_t dbdev_tab[] = { { DSCR_CMD0_PSC1_RX, DEV_FLAGS_IN, 0, 0, 0x11b0001c, 0, 0 }, { DSCR_CMD0_PSC1_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_CIM_RXA, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_CIM_RXB, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, - { DSCR_CMD0_CIM_RXC, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, + { DSCR_CMD0_CIM_RXA, DEV_FLAGS_IN, 0, 32, 0x14004020, 0, 0 }, + { DSCR_CMD0_CIM_RXB, DEV_FLAGS_IN, 0, 32, 0x14004040, 0, 0 }, + { DSCR_CMD0_CIM_RXC, DEV_FLAGS_IN, 0, 32, 0x14004060, 0, 0 }, { DSCR_CMD0_CIM_SYNC, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, { DSCR_CMD0_NAND_FLASH, DEV_FLAGS_IN, 0, 0, 0x00000000, 0, 0 }, @@ -184,6 +160,24 @@ static dbdev_tab_t dbdev_tab[] = { { DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, { DSCR_CMD0_ALWAYS, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }, + + /* Provide 16 user definable device types */ + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, + { 0, 0, 0, 0, 0, 0, 0 }, }; #define DBDEV_TAB_SIZE (sizeof(dbdev_tab) / sizeof(dbdev_tab_t)) @@ -203,6 +197,30 @@ find_dbdev_id (u32 id) return NULL; } +u32 +au1xxx_ddma_add_device(dbdev_tab_t *dev) +{ + u32 ret = 0; + dbdev_tab_t *p=NULL; + static u16 new_id=0x1000; + + p = find_dbdev_id(0); + if ( NULL != p ) + { + memcpy(p, dev, sizeof(dbdev_tab_t)); + p->dev_id = DSCR_DEV2CUSTOM_ID(new_id,dev->dev_id); + ret = p->dev_id; + new_id++; +#if 0 + printk("add_device: id:%x flags:%x padd:%x\n", + p->dev_id, p->dev_flags, p->dev_physaddr ); +#endif + } + + return ret; +} +EXPORT_SYMBOL(au1xxx_ddma_add_device); + /* Allocate a channel and return a non-zero descriptor if successful. */ u32 @@ -215,7 +233,7 @@ au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid, int i; dbdev_tab_t *stp, *dtp; chan_tab_t *ctp; - volatile au1x_dma_chan_t *cp; + au1x_dma_chan_t *cp; /* We do the intialization on the first channel allocation. * We have to wait because of the interrupt handler initialization @@ -225,9 +243,6 @@ au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid, au1xxx_dbdma_init(); dbdma_initialized = 1; - if ((srcid > DSCR_NDEV_IDS) || (destid > DSCR_NDEV_IDS)) - return 0; - if ((stp = find_dbdev_id(srcid)) == NULL) return 0; if ((dtp = find_dbdev_id(destid)) == NULL) return 0; @@ -269,9 +284,9 @@ au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid, /* If kmalloc fails, it is caught below same * as a channel not available. */ - ctp = kmalloc(sizeof(chan_tab_t), GFP_KERNEL); + ctp = (chan_tab_t *) + kmalloc(sizeof(chan_tab_t), GFP_KERNEL); chan_tab_ptr[i] = ctp; - ctp->chan_index = chan = i; break; } } @@ -279,10 +294,11 @@ au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid, if (ctp != NULL) { memset(ctp, 0, sizeof(chan_tab_t)); + ctp->chan_index = chan = i; dcp = DDMA_CHANNEL_BASE; dcp += (0x0100 * chan); ctp->chan_ptr = (au1x_dma_chan_t *)dcp; - cp = (volatile au1x_dma_chan_t *)dcp; + cp = (au1x_dma_chan_t *)dcp; ctp->chan_src = stp; ctp->chan_dest = dtp; ctp->chan_callback = callback; @@ -299,6 +315,9 @@ au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid, i |= DDMA_CFG_DED; if (dtp->dev_intpolarity) i |= DDMA_CFG_DP; + if ((stp->dev_flags & DEV_FLAGS_SYNC) || + (dtp->dev_flags & DEV_FLAGS_SYNC)) + i |= DDMA_CFG_SYNC; cp->ddma_cfg = i; au_sync(); @@ -309,14 +328,14 @@ au1xxx_dbdma_chan_alloc(u32 srcid, u32 destid, rv = (u32)(&chan_tab_ptr[chan]); } else { - /* Release devices. - */ + /* Release devices */ stp->dev_flags &= ~DEV_FLAGS_INUSE; dtp->dev_flags &= ~DEV_FLAGS_INUSE; } } return rv; } +EXPORT_SYMBOL(au1xxx_dbdma_chan_alloc); /* Set the device width if source or destination is a FIFO. * Should be 8, 16, or 32 bits. @@ -344,6 +363,7 @@ au1xxx_dbdma_set_devwidth(u32 chanid, int bits) return rv; } +EXPORT_SYMBOL(au1xxx_dbdma_set_devwidth); /* Allocate a descriptor ring, initializing as much as possible. */ @@ -370,7 +390,8 @@ au1xxx_dbdma_ring_alloc(u32 chanid, int entries) * and if we try that first we are likely to not waste larger * slabs of memory. */ - desc_base = (u32)kmalloc(entries * sizeof(au1x_ddma_desc_t), GFP_KERNEL); + desc_base = (u32)kmalloc(entries * sizeof(au1x_ddma_desc_t), + GFP_KERNEL|GFP_DMA); if (desc_base == 0) return 0; @@ -381,7 +402,7 @@ au1xxx_dbdma_ring_alloc(u32 chanid, int entries) kfree((const void *)desc_base); i = entries * sizeof(au1x_ddma_desc_t); i += (sizeof(au1x_ddma_desc_t) - 1); - if ((desc_base = (u32)kmalloc(i, GFP_KERNEL)) == 0) + if ((desc_base = (u32)kmalloc(i, GFP_KERNEL|GFP_DMA)) == 0) return 0; desc_base = ALIGN_ADDR(desc_base, sizeof(au1x_ddma_desc_t)); @@ -461,9 +482,14 @@ au1xxx_dbdma_ring_alloc(u32 chanid, int entries) /* If source input is fifo, set static address. */ if (stp->dev_flags & DEV_FLAGS_IN) { - src0 = stp->dev_physaddr; + if ( stp->dev_flags & DEV_FLAGS_BURSTABLE ) + src1 |= DSCR_SRC1_SAM(DSCR_xAM_BURST); + else src1 |= DSCR_SRC1_SAM(DSCR_xAM_STATIC); + } + if (stp->dev_physaddr) + src0 = stp->dev_physaddr; /* Set up dest1. For now, assume no stride and increment. * A channel attribute update can change this later. @@ -487,10 +513,18 @@ au1xxx_dbdma_ring_alloc(u32 chanid, int entries) /* If destination output is fifo, set static address. */ if (dtp->dev_flags & DEV_FLAGS_OUT) { - dest0 = dtp->dev_physaddr; + if ( dtp->dev_flags & DEV_FLAGS_BURSTABLE ) + dest1 |= DSCR_DEST1_DAM(DSCR_xAM_BURST); + else dest1 |= DSCR_DEST1_DAM(DSCR_xAM_STATIC); } + if (dtp->dev_physaddr) + dest0 = dtp->dev_physaddr; +#if 0 + printk("did:%x sid:%x cmd0:%x cmd1:%x source0:%x source1:%x dest0:%x dest1:%x\n", + dtp->dev_id, stp->dev_id, cmd0, cmd1, src0, src1, dest0, dest1 ); +#endif for (i=0; idscr_cmd0 = cmd0; dp->dscr_cmd1 = cmd1; @@ -499,6 +533,7 @@ au1xxx_dbdma_ring_alloc(u32 chanid, int entries) dp->dscr_dest0 = dest0; dp->dscr_dest1 = dest1; dp->dscr_stat = 0; + dp->sw_context = dp->sw_status = 0; dp->dscr_nxtptr = DSCR_NXTPTR(virt_to_phys(dp + 1)); dp++; } @@ -511,13 +546,14 @@ au1xxx_dbdma_ring_alloc(u32 chanid, int entries) return (u32)(ctp->chan_desc_base); } +EXPORT_SYMBOL(au1xxx_dbdma_ring_alloc); /* Put a source buffer into the DMA ring. * This updates the source pointer and byte count. Normally used * for memory to fifo transfers. */ u32 -au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes) +_au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes, u32 flags) { chan_tab_t *ctp; au1x_ddma_desc_t *dp; @@ -544,24 +580,40 @@ au1xxx_dbdma_put_source(u32 chanid, void *buf, int nbytes) */ dp->dscr_source0 = virt_to_phys(buf); dp->dscr_cmd1 = nbytes; - dp->dscr_cmd0 |= DSCR_CMD0_V; /* Let it rip */ - ctp->chan_ptr->ddma_dbell = 0xffffffff; /* Make it go */ - + /* Check flags */ + if (flags & DDMA_FLAGS_IE) + dp->dscr_cmd0 |= DSCR_CMD0_IE; + if (flags & DDMA_FLAGS_NOIE) + dp->dscr_cmd0 &= ~DSCR_CMD0_IE; /* Get next descriptor pointer. */ ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr)); + /* + * There is an errata on the Au1200/Au1550 parts that could result + * in "stale" data being DMA'd. It has to do with the snoop logic on + * the dache eviction buffer. NONCOHERENT_IO is on by default for + * these parts. If it is fixedin the future, these dma_cache_inv will + * just be nothing more than empty macros. See io.h. + * */ + dma_cache_wback_inv(buf,nbytes); + dp->dscr_cmd0 |= DSCR_CMD0_V; /* Let it rip */ + au_sync(); + dma_cache_wback_inv(dp, sizeof(dp)); + ctp->chan_ptr->ddma_dbell = 0; + /* return something not zero. */ return nbytes; } +EXPORT_SYMBOL(_au1xxx_dbdma_put_source); /* Put a destination buffer into the DMA ring. * This updates the destination pointer and byte count. Normally used * to place an empty buffer into the ring for fifo to memory transfers. */ u32 -au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes) +_au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes, u32 flags) { chan_tab_t *ctp; au1x_ddma_desc_t *dp; @@ -583,11 +635,33 @@ au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes) if (dp->dscr_cmd0 & DSCR_CMD0_V) return 0; - /* Load up buffer address and byte count. - */ + /* Load up buffer address and byte count */ + + /* Check flags */ + if (flags & DDMA_FLAGS_IE) + dp->dscr_cmd0 |= DSCR_CMD0_IE; + if (flags & DDMA_FLAGS_NOIE) + dp->dscr_cmd0 &= ~DSCR_CMD0_IE; + dp->dscr_dest0 = virt_to_phys(buf); dp->dscr_cmd1 = nbytes; +#if 0 + printk("cmd0:%x cmd1:%x source0:%x source1:%x dest0:%x dest1:%x\n", + dp->dscr_cmd0, dp->dscr_cmd1, dp->dscr_source0, + dp->dscr_source1, dp->dscr_dest0, dp->dscr_dest1 ); +#endif + /* + * There is an errata on the Au1200/Au1550 parts that could result in + * "stale" data being DMA'd. It has to do with the snoop logic on the + * dache eviction buffer. NONCOHERENT_IO is on by default for these + * parts. If it is fixedin the future, these dma_cache_inv will just + * be nothing more than empty macros. See io.h. + * */ + dma_cache_inv(buf,nbytes); dp->dscr_cmd0 |= DSCR_CMD0_V; /* Let it rip */ + au_sync(); + dma_cache_wback_inv(dp, sizeof(dp)); + ctp->chan_ptr->ddma_dbell = 0; /* Get next descriptor pointer. */ @@ -597,6 +671,7 @@ au1xxx_dbdma_put_dest(u32 chanid, void *buf, int nbytes) */ return nbytes; } +EXPORT_SYMBOL(_au1xxx_dbdma_put_dest); /* Get a destination buffer into the DMA ring. * Normally used to get a full buffer from the ring during fifo @@ -646,7 +721,7 @@ void au1xxx_dbdma_stop(u32 chanid) { chan_tab_t *ctp; - volatile au1x_dma_chan_t *cp; + au1x_dma_chan_t *cp; int halt_timeout = 0; ctp = *((chan_tab_t **)chanid); @@ -666,6 +741,7 @@ au1xxx_dbdma_stop(u32 chanid) cp->ddma_stat |= (DDMA_STAT_DB | DDMA_STAT_V); au_sync(); } +EXPORT_SYMBOL(au1xxx_dbdma_stop); /* Start using the current descriptor pointer. If the dbdma encounters * a not valid descriptor, it will stop. In this case, we can just @@ -675,17 +751,17 @@ void au1xxx_dbdma_start(u32 chanid) { chan_tab_t *ctp; - volatile au1x_dma_chan_t *cp; + au1x_dma_chan_t *cp; ctp = *((chan_tab_t **)chanid); - cp = ctp->chan_ptr; cp->ddma_desptr = virt_to_phys(ctp->cur_ptr); cp->ddma_cfg |= DDMA_CFG_EN; /* Enable channel */ au_sync(); - cp->ddma_dbell = 0xffffffff; /* Make it go */ + cp->ddma_dbell = 0; au_sync(); } +EXPORT_SYMBOL(au1xxx_dbdma_start); void au1xxx_dbdma_reset(u32 chanid) @@ -704,15 +780,21 @@ au1xxx_dbdma_reset(u32 chanid) do { dp->dscr_cmd0 &= ~DSCR_CMD0_V; + /* reset our SW status -- this is used to determine + * if a descriptor is in use by upper level SW. Since + * posting can reset 'V' bit. + */ + dp->sw_status = 0; dp = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr)); } while (dp != ctp->chan_desc_base); } +EXPORT_SYMBOL(au1xxx_dbdma_reset); u32 au1xxx_get_dma_residue(u32 chanid) { chan_tab_t *ctp; - volatile au1x_dma_chan_t *cp; + au1x_dma_chan_t *cp; u32 rv; ctp = *((chan_tab_t **)chanid); @@ -747,15 +829,16 @@ au1xxx_dbdma_chan_free(u32 chanid) kfree(ctp); } +EXPORT_SYMBOL(au1xxx_dbdma_chan_free); -static irqreturn_t +static void dbdma_interrupt(int irq, void *dev_id, struct pt_regs *regs) { - u32 intstat; + u32 intstat, flags; u32 chan_index; chan_tab_t *ctp; au1x_ddma_desc_t *dp; - volatile au1x_dma_chan_t *cp; + au1x_dma_chan_t *cp; intstat = dbdma_gptr->ddma_intstat; au_sync(); @@ -774,19 +857,26 @@ dbdma_interrupt(int irq, void *dev_id, struct pt_regs *regs) (ctp->chan_callback)(irq, ctp->chan_callparam, regs); ctp->cur_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr)); - - return IRQ_HANDLED; } -static void -au1xxx_dbdma_init(void) +static void au1xxx_dbdma_init(void) { + int irq_nr; + dbdma_gptr->ddma_config = 0; dbdma_gptr->ddma_throttle = 0; dbdma_gptr->ddma_inten = 0xffff; au_sync(); - if (request_irq(AU1550_DDMA_INT, dbdma_interrupt, SA_INTERRUPT, +#if defined(CONFIG_SOC_AU1550) + irq_nr = AU1550_DDMA_INT; +#elif defined(CONFIG_SOC_AU1200) + irq_nr = AU1200_DDMA_INT; +#else + #error Unknown Au1x00 SOC +#endif + + if (request_irq(irq_nr, dbdma_interrupt, SA_INTERRUPT, "Au1xxx dbdma", (void *)dbdma_gptr)) printk("Can't get 1550 dbdma irq"); } @@ -797,7 +887,8 @@ au1xxx_dbdma_dump(u32 chanid) chan_tab_t *ctp; au1x_ddma_desc_t *dp; dbdev_tab_t *stp, *dtp; - volatile au1x_dma_chan_t *cp; + au1x_dma_chan_t *cp; + u32 i = 0; ctp = *((chan_tab_t **)chanid); stp = ctp->chan_src; @@ -822,15 +913,64 @@ au1xxx_dbdma_dump(u32 chanid) dp = ctp->chan_desc_base; do { - printk("dp %08x, cmd0 %08x, cmd1 %08x\n", - (u32)dp, dp->dscr_cmd0, dp->dscr_cmd1); - printk("src0 %08x, src1 %08x, dest0 %08x\n", - dp->dscr_source0, dp->dscr_source1, dp->dscr_dest0); - printk("dest1 %08x, stat %08x, nxtptr %08x\n", - dp->dscr_dest1, dp->dscr_stat, dp->dscr_nxtptr); + printk("Dp[%d]= %08x, cmd0 %08x, cmd1 %08x\n", + i++, (u32)dp, dp->dscr_cmd0, dp->dscr_cmd1); + printk("src0 %08x, src1 %08x, dest0 %08x, dest1 %08x\n", + dp->dscr_source0, dp->dscr_source1, dp->dscr_dest0, dp->dscr_dest1); + printk("stat %08x, nxtptr %08x\n", + dp->dscr_stat, dp->dscr_nxtptr); dp = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr)); } while (dp != ctp->chan_desc_base); } +/* Put a descriptor into the DMA ring. + * This updates the source/destination pointers and byte count. + */ +u32 +au1xxx_dbdma_put_dscr(u32 chanid, au1x_ddma_desc_t *dscr ) +{ + chan_tab_t *ctp; + au1x_ddma_desc_t *dp; + u32 nbytes=0; + + /* I guess we could check this to be within the + * range of the table...... + */ + ctp = *((chan_tab_t **)chanid); + + /* We should have multiple callers for a particular channel, + * an interrupt doesn't affect this pointer nor the descriptor, + * so no locking should be needed. + */ + dp = ctp->put_ptr; + + /* If the descriptor is valid, we are way ahead of the DMA + * engine, so just return an error condition. + */ + if (dp->dscr_cmd0 & DSCR_CMD0_V) + return 0; + + /* Load up buffer addresses and byte count. + */ + dp->dscr_dest0 = dscr->dscr_dest0; + dp->dscr_source0 = dscr->dscr_source0; + dp->dscr_dest1 = dscr->dscr_dest1; + dp->dscr_source1 = dscr->dscr_source1; + dp->dscr_cmd1 = dscr->dscr_cmd1; + nbytes = dscr->dscr_cmd1; + /* Allow the caller to specifiy if an interrupt is generated */ + dp->dscr_cmd0 &= ~DSCR_CMD0_IE; + dp->dscr_cmd0 |= dscr->dscr_cmd0 | DSCR_CMD0_V; + ctp->chan_ptr->ddma_dbell = 0; + + /* Get next descriptor pointer. + */ + ctp->put_ptr = phys_to_virt(DSCR_GET_NXTPTR(dp->dscr_nxtptr)); + + /* return something not zero. + */ + return nbytes; +} + #endif /* defined(CONFIG_SOC_AU1550) || defined(CONFIG_SOC_AU1200) */ diff --git a/arch/mips/au1000/common/irq.c b/arch/mips/au1000/common/irq.c index 0b912f739febc..ebf93bdbad140 100644 --- a/arch/mips/au1000/common/irq.c +++ b/arch/mips/au1000/common/irq.c @@ -488,7 +488,7 @@ void intc0_req0_irqdispatch(struct pt_regs *regs) intc0_req0 |= au_readl(IC0_REQ0INT); if (!intc0_req0) return; - +#ifdef AU1000_USB_DEV_REQ_INT /* * Because of the tight timing of SETUP token to reply * transactions, the USB devices-side packet complete @@ -499,7 +499,7 @@ void intc0_req0_irqdispatch(struct pt_regs *regs) do_IRQ(AU1000_USB_DEV_REQ_INT, regs); return; } - +#endif irq = au_ffs(intc0_req0) - 1; intc0_req0 &= ~(1<ep0_stage = SETUP_STAGE; break; - } + } spin_unlock(&ep0->lock); - // we're done processing the packet, free it - kfree(pkt); + // we're done processing the packet, free it + kfree(pkt); } @@ -1072,8 +1072,7 @@ dma_done_ep0_intr(int irq, void *dev_id, struct pt_regs *regs) clear_dma_done1(ep0->indma); pkt = send_packet_complete(ep0); - if (pkt) - kfree(pkt); + kfree(pkt); } /* @@ -1302,8 +1301,7 @@ usbdev_exit(void) endpoint_flush(ep); } - if (usbdev.full_conf_desc) - kfree(usbdev.full_conf_desc); + kfree(usbdev.full_conf_desc); } int diff --git a/arch/mips/au1000/pb1200/Makefile b/arch/mips/au1000/pb1200/Makefile new file mode 100644 index 0000000000000..22b673cf55afd --- /dev/null +++ b/arch/mips/au1000/pb1200/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for the Alchemy Semiconductor PB1200 board. +# + +lib-y := init.o board_setup.o irqmap.o diff --git a/arch/mips/au1000/pb1200/board_setup.c b/arch/mips/au1000/pb1200/board_setup.c new file mode 100644 index 0000000000000..209a07cb73210 --- /dev/null +++ b/arch/mips/au1000/pb1200/board_setup.c @@ -0,0 +1,187 @@ +/* + * + * BRIEF MODULE DESCRIPTION + * Alchemy Pb1200/Db1200 board setup. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include +#include +#include +#include +#include +#include +#include +#include + +#if defined(CONFIG_BLK_DEV_IDE_AU1XXX) +#include +#endif + +#include +#include +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_MIPS_PB1200 +#include +#endif + +#ifdef CONFIG_MIPS_DB1200 +#include +#define PB1200_ETH_INT DB1200_ETH_INT +#define PB1200_IDE_INT DB1200_IDE_INT +#endif + +extern void _board_init_irq(void); +extern void (*board_init_irq)(void); + +#ifdef CONFIG_BLK_DEV_IDE_AU1XXX +extern struct ide_ops *ide_ops; +extern struct ide_ops au1xxx_ide_ops; +extern u32 au1xxx_ide_virtbase; +extern u64 au1xxx_ide_physbase; +extern int au1xxx_ide_irq; + +u32 led_base_addr; +/* Ddma */ +chan_tab_t *ide_read_ch, *ide_write_ch; +u32 au1xxx_ide_ddma_enable = 0, switch4ddma = 1; // PIO+ddma + +dbdev_tab_t new_dbdev_tab_element = { DSCR_CMD0_THROTTLE, DEV_FLAGS_ANYUSE, 0, 0, 0x00000000, 0, 0 }; +#endif /* end CONFIG_BLK_DEV_IDE_AU1XXX */ + +void board_reset (void) +{ + bcsr->resets = 0; +} + +void __init board_setup(void) +{ + char *argptr = NULL; + u32 pin_func; + +#if 0 + /* Enable PSC1 SYNC for AC97. Normaly done in audio driver, + * but it is board specific code, so put it here. + */ + pin_func = au_readl(SYS_PINFUNC); + au_sync(); + pin_func |= SYS_PF_MUST_BE_SET | SYS_PF_PSC1_S1; + au_writel(pin_func, SYS_PINFUNC); + + au_writel(0, (u32)bcsr|0x10); /* turn off pcmcia power */ + au_sync(); +#endif + +#if defined( CONFIG_I2C_ALGO_AU1550 ) + { + u32 freq0, clksrc; + + /* Select SMBUS in CPLD */ + bcsr->resets &= ~(BCSR_RESETS_PCS0MUX); + + pin_func = au_readl(SYS_PINFUNC); + au_sync(); + pin_func &= ~(3<<17 | 1<<4); + /* Set GPIOs correctly */ + pin_func |= 2<<17; + au_writel(pin_func, SYS_PINFUNC); + au_sync(); + + /* The i2c driver depends on 50Mhz clock */ + freq0 = au_readl(SYS_FREQCTRL0); + au_sync(); + freq0 &= ~(SYS_FC_FRDIV1_MASK | SYS_FC_FS1 | SYS_FC_FE1); + freq0 |= (3<resets bit 12: 0=SMB 1=SPI + */ +#if defined(CONFIG_AU1550_PSC_SPI) && defined(CONFIG_I2C_ALGO_AU1550) + #error I2C and SPI are mutually exclusive. Both are physically connected to PSC0.\ + Refer to Pb1200/Db1200 documentation. +#elif defined( CONFIG_AU1550_PSC_SPI ) + bcsr->resets |= BCSR_RESETS_PCS0MUX; +#elif defined( CONFIG_I2C_ALGO_AU1550 ) + bcsr->resets &= (~BCSR_RESETS_PCS0MUX); +#endif + au_sync(); + +#ifdef CONFIG_MIPS_PB1200 + printk("AMD Alchemy Pb1200 Board\n"); +#endif +#ifdef CONFIG_MIPS_DB1200 + printk("AMD Alchemy Db1200 Board\n"); +#endif +#if 0 + /* Setup Pb1200 External Interrupt Controller */ + { + extern void (*board_init_irq)(void); + extern void _board_init_irq(void); + board_init_irq = _board_init_irq; + } +#endif +} diff --git a/arch/mips/au1000/pb1200/init.c b/arch/mips/au1000/pb1200/init.c new file mode 100644 index 0000000000000..27f09e374e159 --- /dev/null +++ b/arch/mips/au1000/pb1200/init.c @@ -0,0 +1,69 @@ +/* + * + * BRIEF MODULE DESCRIPTION + * PB1200 board setup + * + * Copyright 2001 MontaVista Software Inc. + * Author: MontaVista Software, Inc. + * ppopov@mvista.com or source@mvista.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include +#include +#include +#include +#include +#include +#include +#include + +int prom_argc; +char **prom_argv, **prom_envp; +extern void __init prom_init_cmdline(void); +extern char *prom_getenv(char *envname); + +const char *get_system_type(void) +{ + return "Alchemy Pb1200"; +} + +void __init prom_init(void) +{ + unsigned char *memsize_str; + unsigned long memsize; + + prom_argc = (int) fw_arg0; + prom_argv = (char **) fw_arg1; + prom_envp = (char **) fw_arg2; + + mips_machgroup = MACH_GROUP_ALCHEMY; + mips_machtype = MACH_PB1200; + + prom_init_cmdline(); + memsize_str = prom_getenv("memsize"); + if (!memsize_str) { + memsize = 0x08000000; + } else { + memsize = simple_strtol(memsize_str, NULL, 0); + } + add_memory_region(0, memsize, BOOT_MEM_RAM); +} diff --git a/arch/mips/au1000/pb1200/irqmap.c b/arch/mips/au1000/pb1200/irqmap.c new file mode 100644 index 0000000000000..2ec64e78aa01f --- /dev/null +++ b/arch/mips/au1000/pb1200/irqmap.c @@ -0,0 +1,180 @@ +/* + * BRIEF MODULE DESCRIPTION + * Au1xxx irq map table + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED + * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN + * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, + * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF + * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON + * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF + * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include + +#ifdef CONFIG_MIPS_PB1200 +#include +#endif + +#ifdef CONFIG_MIPS_DB1200 +#include +#define PB1200_INT_BEGIN DB1200_INT_BEGIN +#define PB1200_INT_END DB1200_INT_END +#endif + +au1xxx_irq_map_t au1xxx_irq_map[] = { + { AU1000_GPIO_7, INTC_INT_LOW_LEVEL, 0 }, // This is exteranl interrupt cascade +}; + +int au1xxx_nr_irqs = sizeof(au1xxx_irq_map)/sizeof(au1xxx_irq_map_t); + +/* + * Support for External interrupts on the PbAu1200 Development platform. + */ +static volatile int pb1200_cascade_en=0; + +void pb1200_cascade_handler( int irq, void *dev_id, struct pt_regs *regs) +{ + unsigned short bisr = bcsr->int_status; + int extirq_nr = 0; + + /* Clear all the edge interrupts. This has no effect on level */ + bcsr->int_status = bisr; + for( ; bisr; bisr &= (bisr-1) ) + { + extirq_nr = (PB1200_INT_BEGIN-1) + au_ffs(bisr); + /* Ack and dispatch IRQ */ + do_IRQ(extirq_nr,regs); + } +} + +inline void pb1200_enable_irq(unsigned int irq_nr) +{ + bcsr->intset_mask = 1<<(irq_nr - PB1200_INT_BEGIN); + bcsr->intset = 1<<(irq_nr - PB1200_INT_BEGIN); +} + +inline void pb1200_disable_irq(unsigned int irq_nr) +{ + bcsr->intclr_mask = 1<<(irq_nr - PB1200_INT_BEGIN); + bcsr->intclr = 1<<(irq_nr - PB1200_INT_BEGIN); +} + +static unsigned int pb1200_startup_irq( unsigned int irq_nr ) +{ + if (++pb1200_cascade_en == 1) + { + request_irq(AU1000_GPIO_7, &pb1200_cascade_handler, + 0, "Pb1200 Cascade", &pb1200_cascade_handler ); +#ifdef CONFIG_MIPS_PB1200 + /* We have a problem with CPLD rev3. Enable a workaround */ + if( ((bcsr->whoami & BCSR_WHOAMI_CPLD)>>4) <= 3) + { + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("Pb1200 must be at CPLD rev4. Please have Pb1200\n"); + printk("updated to latest revision. This software will not\n"); + printk("work on anything less than CPLD rev4\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + printk("\nWARNING!!!\n"); + while(1); + } +#endif + } + pb1200_enable_irq(irq_nr); + return 0; +} + +static void pb1200_shutdown_irq( unsigned int irq_nr ) +{ + pb1200_disable_irq(irq_nr); + if (--pb1200_cascade_en == 0) + { + free_irq(AU1000_GPIO_7,&pb1200_cascade_handler ); + } + return; +} + +static inline void pb1200_mask_and_ack_irq(unsigned int irq_nr) +{ + pb1200_disable_irq( irq_nr ); +} + +static void pb1200_end_irq(unsigned int irq_nr) +{ + if (!(irq_desc[irq_nr].status & (IRQ_DISABLED|IRQ_INPROGRESS))) { + pb1200_enable_irq(irq_nr); + } +} + +static struct hw_interrupt_type external_irq_type = +{ +#ifdef CONFIG_MIPS_PB1200 + "Pb1200 Ext", +#endif +#ifdef CONFIG_MIPS_DB1200 + "Db1200 Ext", +#endif + pb1200_startup_irq, + pb1200_shutdown_irq, + pb1200_enable_irq, + pb1200_disable_irq, + pb1200_mask_and_ack_irq, + pb1200_end_irq, + NULL +}; + +void _board_init_irq(void) +{ + int irq_nr; + + for (irq_nr = PB1200_INT_BEGIN; irq_nr <= PB1200_INT_END; irq_nr++) + { + irq_desc[irq_nr].handler = &external_irq_type; + pb1200_disable_irq(irq_nr); + } + + /* GPIO_7 can not be hooked here, so it is hooked upon first + request of any source attached to the cascade */ +} + diff --git a/arch/mips/kernel/cpu-probe.c b/arch/mips/kernel/cpu-probe.c index 7685f8baf3f02..66c2a2788ffe2 100644 --- a/arch/mips/kernel/cpu-probe.c +++ b/arch/mips/kernel/cpu-probe.c @@ -116,6 +116,8 @@ static inline void check_wait(void) case CPU_AU1000: case CPU_AU1100: case CPU_AU1500: + case CPU_AU1550: + case CPU_AU1200: if (au1k_wait_ptr != NULL) { cpu_wait = au1k_wait_ptr; printk(" available.\n"); @@ -505,6 +507,9 @@ static inline void cpu_probe_alchemy(struct cpuinfo_mips *c) case 3: c->cputype = CPU_AU1550; break; + case 4: + c->cputype = CPU_AU1200; + break; default: panic("Unknown Au Core!"); break; diff --git a/arch/mips/kernel/proc.c b/arch/mips/kernel/proc.c index 760fcdfea18e2..13888520d41c8 100644 --- a/arch/mips/kernel/proc.c +++ b/arch/mips/kernel/proc.c @@ -60,6 +60,9 @@ static const char *cpu_name[] = { [CPU_TX3927] "TX3927", [CPU_AU1000] "Au1000", [CPU_AU1500] "Au1500", + [CPU_AU1100] "Au1100", + [CPU_AU1550] "Au1550", + [CPU_AU1200] "Au1200", [CPU_4KEC] "MIPS 4KEc", [CPU_4KSC] "MIPS 4KSc", [CPU_VR41XX] "NEC Vr41xx", diff --git a/arch/mips/mm/c-r4k.c b/arch/mips/mm/c-r4k.c index 03100b8a45d98..e26dd829bf204 100644 --- a/arch/mips/mm/c-r4k.c +++ b/arch/mips/mm/c-r4k.c @@ -1036,7 +1036,11 @@ static void __init probe_pcache(void) c->icache.flags |= MIPS_CACHE_VTAG; break; + case CPU_AU1000: case CPU_AU1500: + case CPU_AU1100: + case CPU_AU1550: + case CPU_AU1200: c->icache.flags |= MIPS_CACHE_IC_F_DC; break; } diff --git a/arch/mips/mm/tlbex.c b/arch/mips/mm/tlbex.c index 6569be3983c79..248537cebc899 100644 --- a/arch/mips/mm/tlbex.c +++ b/arch/mips/mm/tlbex.c @@ -840,6 +840,7 @@ static __init void build_tlb_write_entry(u32 **p, struct label **l, case CPU_AU1100: case CPU_AU1500: case CPU_AU1550: + case CPU_AU1200: i_nop(p); tlbw(p); break; diff --git a/include/asm-mips/bootinfo.h b/include/asm-mips/bootinfo.h index b1e57d7836045..404856e6b82d8 100644 --- a/include/asm-mips/bootinfo.h +++ b/include/asm-mips/bootinfo.h @@ -177,6 +177,8 @@ #define MACH_MTX1 7 /* 4G MTX-1 Au1500-based board */ #define MACH_PB1550 8 /* Au1550-based eval board */ #define MACH_DB1550 9 /* Au1550-based eval board */ +#define MACH_PB1200 10 /* Au1200-based eval board */ +#define MACH_DB1200 11 /* Au1200-based eval board */ /* * Valid machtype for group NEC_VR41XX diff --git a/include/asm-mips/cpu.h b/include/asm-mips/cpu.h index c60281799801d..8e167bfd40b18 100644 --- a/include/asm-mips/cpu.h +++ b/include/asm-mips/cpu.h @@ -182,7 +182,8 @@ #define CPU_VR4133 56 #define CPU_AU1550 57 #define CPU_24K 58 -#define CPU_LAST 58 +#define CPU_AU1200 59 +#define CPU_LAST 59 /* * ISA Level encodings diff --git a/include/asm-mips/mach-au1x00/au1000.h b/include/asm-mips/mach-au1x00/au1000.h index 148bae2fa7d32..28b04a5f67cf6 100644 --- a/include/asm-mips/mach-au1x00/au1000.h +++ b/include/asm-mips/mach-au1x00/au1000.h @@ -162,27 +162,355 @@ extern au1xxx_irq_map_t au1xxx_irq_map[]; #define ALLINTS (IE_IRQ0 | IE_IRQ1 | IE_IRQ2 | IE_IRQ3 | IE_IRQ4 | IE_IRQ5) #endif -/* SDRAM Controller */ +/* + * SDRAM Register Offsets + */ #if defined(CONFIG_SOC_AU1000) || defined(CONFIG_SOC_AU1500) || defined(CONFIG_SOC_AU1100) -#define MEM_SDMODE0 0xB4000000 -#define MEM_SDMODE1 0xB4000004 -#define MEM_SDMODE2 0xB4000008 +#define MEM_SDMODE0 (0x0000) +#define MEM_SDMODE1 (0x0004) +#define MEM_SDMODE2 (0x0008) +#define MEM_SDADDR0 (0x000C) +#define MEM_SDADDR1 (0x0010) +#define MEM_SDADDR2 (0x0014) +#define MEM_SDREFCFG (0x0018) +#define MEM_SDPRECMD (0x001C) +#define MEM_SDAUTOREF (0x0020) +#define MEM_SDWRMD0 (0x0024) +#define MEM_SDWRMD1 (0x0028) +#define MEM_SDWRMD2 (0x002C) +#define MEM_SDSLEEP (0x0030) +#define MEM_SDSMCKE (0x0034) + +#ifndef ASSEMBLER +/*typedef volatile struct +{ + uint32 sdmode0; + uint32 sdmode1; + uint32 sdmode2; + uint32 sdaddr0; + uint32 sdaddr1; + uint32 sdaddr2; + uint32 sdrefcfg; + uint32 sdautoref; + uint32 sdwrmd0; + uint32 sdwrmd1; + uint32 sdwrmd2; + uint32 sdsleep; + uint32 sdsmcke; + +} AU1X00_SDRAM;*/ +#endif + +/* + * MEM_SDMODE register content definitions + */ +#define MEM_SDMODE_F (1<<22) +#define MEM_SDMODE_SR (1<<21) +#define MEM_SDMODE_BS (1<<20) +#define MEM_SDMODE_RS (3<<18) +#define MEM_SDMODE_CS (7<<15) +#define MEM_SDMODE_TRAS (15<<11) +#define MEM_SDMODE_TMRD (3<<9) +#define MEM_SDMODE_TWR (3<<7) +#define MEM_SDMODE_TRP (3<<5) +#define MEM_SDMODE_TRCD (3<<3) +#define MEM_SDMODE_TCL (7<<0) + +#define MEM_SDMODE_BS_2Bank (0<<20) +#define MEM_SDMODE_BS_4Bank (1<<20) +#define MEM_SDMODE_RS_11Row (0<<18) +#define MEM_SDMODE_RS_12Row (1<<18) +#define MEM_SDMODE_RS_13Row (2<<18) +#define MEM_SDMODE_RS_N(N) ((N)<<18) +#define MEM_SDMODE_CS_7Col (0<<15) +#define MEM_SDMODE_CS_8Col (1<<15) +#define MEM_SDMODE_CS_9Col (2<<15) +#define MEM_SDMODE_CS_10Col (3<<15) +#define MEM_SDMODE_CS_11Col (4<<15) +#define MEM_SDMODE_CS_N(N) ((N)<<15) +#define MEM_SDMODE_TRAS_N(N) ((N)<<11) +#define MEM_SDMODE_TMRD_N(N) ((N)<<9) +#define MEM_SDMODE_TWR_N(N) ((N)<<7) +#define MEM_SDMODE_TRP_N(N) ((N)<<5) +#define MEM_SDMODE_TRCD_N(N) ((N)<<3) +#define MEM_SDMODE_TCL_N(N) ((N)<<0) + +/* + * MEM_SDADDR register contents definitions + */ +#define MEM_SDADDR_E (1<<20) +#define MEM_SDADDR_CSBA (0x03FF<<10) +#define MEM_SDADDR_CSMASK (0x03FF<<0) +#define MEM_SDADDR_CSBA_N(N) ((N)&(0x03FF<<22)>>12) +#define MEM_SDADDR_CSMASK_N(N) ((N)&(0x03FF<<22)>>22) + +/* + * MEM_SDREFCFG register content definitions + */ +#define MEM_SDREFCFG_TRC (15<<28) +#define MEM_SDREFCFG_TRPM (3<<26) +#define MEM_SDREFCFG_E (1<<25) +#define MEM_SDREFCFG_RE (0x1ffffff<<0) +#define MEM_SDREFCFG_TRC_N(N) ((N)< + +// This is defined in au1000.h with bogus value +#undef AU1X00_EXTERNAL_INT + +#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX +#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX +#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC1_TX +#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC1_RX + +/* SPI and SMB are muxed on the Pb1200 board. + Refer to board documentation. + */ +#define SPI_PSC_BASE PSC0_BASE_ADDR +#define SMBUS_PSC_BASE PSC0_BASE_ADDR +/* AC97 and I2S are muxed on the Pb1200 board. + Refer to board documentation. + */ +#define AC97_PSC_BASE PSC1_BASE_ADDR +#define I2S_PSC_BASE PSC1_BASE_ADDR + +#define BCSR_KSEG1_ADDR 0xB9800000 + +typedef volatile struct +{ + /*00*/ u16 whoami; + u16 reserved0; + /*04*/ u16 status; + u16 reserved1; + /*08*/ u16 switches; + u16 reserved2; + /*0C*/ u16 resets; + u16 reserved3; + + /*10*/ u16 pcmcia; + u16 reserved4; + /*14*/ u16 board; + u16 reserved5; + /*18*/ u16 disk_leds; + u16 reserved6; + /*1C*/ u16 system; + u16 reserved7; + + /*20*/ u16 intclr; + u16 reserved8; + /*24*/ u16 intset; + u16 reserved9; + /*28*/ u16 intclr_mask; + u16 reserved10; + /*2C*/ u16 intset_mask; + u16 reserved11; + + /*30*/ u16 sig_status; + u16 reserved12; + /*34*/ u16 int_status; + u16 reserved13; + /*38*/ u16 reserved14; + u16 reserved15; + /*3C*/ u16 reserved16; + u16 reserved17; + +} BCSR; + +static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR; + +/* + * Register bit definitions for the BCSRs + */ +#define BCSR_WHOAMI_DCID 0x000F +#define BCSR_WHOAMI_CPLD 0x00F0 +#define BCSR_WHOAMI_BOARD 0x0F00 + +#define BCSR_STATUS_PCMCIA0VS 0x0003 +#define BCSR_STATUS_PCMCIA1VS 0x000C +#define BCSR_STATUS_SWAPBOOT 0x0040 +#define BCSR_STATUS_FLASHBUSY 0x0100 +#define BCSR_STATUS_IDECBLID 0x0200 +#define BCSR_STATUS_SD0WP 0x0400 +#define BCSR_STATUS_U0RXD 0x1000 +#define BCSR_STATUS_U1RXD 0x2000 + +#define BCSR_SWITCHES_OCTAL 0x00FF +#define BCSR_SWITCHES_DIP_1 0x0080 +#define BCSR_SWITCHES_DIP_2 0x0040 +#define BCSR_SWITCHES_DIP_3 0x0020 +#define BCSR_SWITCHES_DIP_4 0x0010 +#define BCSR_SWITCHES_DIP_5 0x0008 +#define BCSR_SWITCHES_DIP_6 0x0004 +#define BCSR_SWITCHES_DIP_7 0x0002 +#define BCSR_SWITCHES_DIP_8 0x0001 +#define BCSR_SWITCHES_ROTARY 0x0F00 + +#define BCSR_RESETS_ETH 0x0001 +#define BCSR_RESETS_CAMERA 0x0002 +#define BCSR_RESETS_DC 0x0004 +#define BCSR_RESETS_IDE 0x0008 +#define BCSR_RESETS_TV 0x0010 +/* not resets but in the same register */ +#define BCSR_RESETS_PWMR1mUX 0x0800 +#define BCSR_RESETS_PCS0MUX 0x1000 +#define BCSR_RESETS_PCS1MUX 0x2000 +#define BCSR_RESETS_SPISEL 0x4000 + +#define BCSR_PCMCIA_PC0VPP 0x0003 +#define BCSR_PCMCIA_PC0VCC 0x000C +#define BCSR_PCMCIA_PC0DRVEN 0x0010 +#define BCSR_PCMCIA_PC0RST 0x0080 +#define BCSR_PCMCIA_PC1VPP 0x0300 +#define BCSR_PCMCIA_PC1VCC 0x0C00 +#define BCSR_PCMCIA_PC1DRVEN 0x1000 +#define BCSR_PCMCIA_PC1RST 0x8000 + +#define BCSR_BOARD_LCDVEE 0x0001 +#define BCSR_BOARD_LCDVDD 0x0002 +#define BCSR_BOARD_LCDBL 0x0004 +#define BCSR_BOARD_CAMSNAP 0x0010 +#define BCSR_BOARD_CAMPWR 0x0020 +#define BCSR_BOARD_SD0PWR 0x0040 + +#define BCSR_LEDS_DECIMALS 0x0003 +#define BCSR_LEDS_LED0 0x0100 +#define BCSR_LEDS_LED1 0x0200 +#define BCSR_LEDS_LED2 0x0400 +#define BCSR_LEDS_LED3 0x0800 + +#define BCSR_SYSTEM_POWEROFF 0x4000 +#define BCSR_SYSTEM_RESET 0x8000 + +/* Bit positions for the different interrupt sources */ +#define BCSR_INT_IDE 0x0001 +#define BCSR_INT_ETH 0x0002 +#define BCSR_INT_PC0 0x0004 +#define BCSR_INT_PC0STSCHG 0x0008 +#define BCSR_INT_PC1 0x0010 +#define BCSR_INT_PC1STSCHG 0x0020 +#define BCSR_INT_DC 0x0040 +#define BCSR_INT_FLASHBUSY 0x0080 +#define BCSR_INT_PC0INSERT 0x0100 +#define BCSR_INT_PC0EJECT 0x0200 +#define BCSR_INT_PC1INSERT 0x0400 +#define BCSR_INT_PC1EJECT 0x0800 +#define BCSR_INT_SD0INSERT 0x1000 +#define BCSR_INT_SD0EJECT 0x2000 + +#define AU1XXX_SMC91111_PHYS_ADDR (0x19000300) +#define AU1XXX_SMC91111_IRQ DB1200_ETH_INT + +#define AU1XXX_ATA_PHYS_ADDR (0x18800000) +#define AU1XXX_ATA_PHYS_LEN (0x100) +#define AU1XXX_ATA_REG_OFFSET (5) +#define AU1XXX_ATA_INT DB1200_IDE_INT +#define AU1XXX_ATA_DDMA_REQ DSCR_CMD0_DMA_REQ1; +#define AU1XXX_ATA_RQSIZE 128 + +#define NAND_PHYS_ADDR 0x20000000 + +/* + * External Interrupts for Pb1200 as of 8/6/2004. + * Bit positions in the CPLD registers can be calculated by taking + * the interrupt define and subtracting the DB1200_INT_BEGIN value. + * *example: IDE bis pos is = 64 - 64 + ETH bit pos is = 65 - 64 + */ +#define DB1200_INT_BEGIN (AU1000_LAST_INTC1_INT + 1) +#define DB1200_IDE_INT (DB1200_INT_BEGIN + 0) +#define DB1200_ETH_INT (DB1200_INT_BEGIN + 1) +#define DB1200_PC0_INT (DB1200_INT_BEGIN + 2) +#define DB1200_PC0_STSCHG_INT (DB1200_INT_BEGIN + 3) +#define DB1200_PC1_INT (DB1200_INT_BEGIN + 4) +#define DB1200_PC1_STSCHG_INT (DB1200_INT_BEGIN + 5) +#define DB1200_DC_INT (DB1200_INT_BEGIN + 6) +#define DB1200_FLASHBUSY_INT (DB1200_INT_BEGIN + 7) +#define DB1200_PC0_INSERT_INT (DB1200_INT_BEGIN + 8) +#define DB1200_PC0_EJECT_INT (DB1200_INT_BEGIN + 9) +#define DB1200_PC1_INSERT_INT (DB1200_INT_BEGIN + 10) +#define DB1200_PC1_EJECT_INT (DB1200_INT_BEGIN + 11) +#define DB1200_SD0_INSERT_INT (DB1200_INT_BEGIN + 12) +#define DB1200_SD0_EJECT_INT (DB1200_INT_BEGIN + 13) + +#define DB1200_INT_END (DB1200_INT_BEGIN + 15) + +/* For drivers/pcmcia/au1000_db1x00.c */ +#define BOARD_PC0_INT DB1200_PC0_INT +#define BOARD_PC1_INT DB1200_PC1_INT +#define BOARD_CARD_INSERTED(SOCKET) bcsr->sig_status & (1<<(8+(2*SOCKET))) + +#endif /* __ASM_DB1200_H */ + diff --git a/include/asm-mips/mach-pb1x00/pb1200.h b/include/asm-mips/mach-pb1x00/pb1200.h new file mode 100644 index 0000000000000..0f6646335e908 --- /dev/null +++ b/include/asm-mips/mach-pb1x00/pb1200.h @@ -0,0 +1,244 @@ +/* + * AMD Alchemy PB1200 Referrence Board + * Board Registers defines. + * + * ######################################################################## + * + * This program is free software; you can distribute it and/or modify it + * under the terms of the GNU General Public License (Version 2) as + * published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License + * for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 59 Temple Place - Suite 330, Boston MA 02111-1307, USA. + * + * ######################################################################## + * + * + */ +#ifndef __ASM_PB1200_H +#define __ASM_PB1200_H + +#include + +// This is defined in au1000.h with bogus value +#undef AU1X00_EXTERNAL_INT + +#define DBDMA_AC97_TX_CHAN DSCR_CMD0_PSC1_TX +#define DBDMA_AC97_RX_CHAN DSCR_CMD0_PSC1_RX +#define DBDMA_I2S_TX_CHAN DSCR_CMD0_PSC1_TX +#define DBDMA_I2S_RX_CHAN DSCR_CMD0_PSC1_RX + +/* SPI and SMB are muxed on the Pb1200 board. + Refer to board documentation. + */ +#define SPI_PSC_BASE PSC0_BASE_ADDR +#define SMBUS_PSC_BASE PSC0_BASE_ADDR +/* AC97 and I2S are muxed on the Pb1200 board. + Refer to board documentation. + */ +#define AC97_PSC_BASE PSC1_BASE_ADDR +#define I2S_PSC_BASE PSC1_BASE_ADDR + +#define BCSR_KSEG1_ADDR 0xAD800000 + +typedef volatile struct +{ + /*00*/ u16 whoami; + u16 reserved0; + /*04*/ u16 status; + u16 reserved1; + /*08*/ u16 switches; + u16 reserved2; + /*0C*/ u16 resets; + u16 reserved3; + + /*10*/ u16 pcmcia; + u16 reserved4; + /*14*/ u16 board; + u16 reserved5; + /*18*/ u16 disk_leds; + u16 reserved6; + /*1C*/ u16 system; + u16 reserved7; + + /*20*/ u16 intclr; + u16 reserved8; + /*24*/ u16 intset; + u16 reserved9; + /*28*/ u16 intclr_mask; + u16 reserved10; + /*2C*/ u16 intset_mask; + u16 reserved11; + + /*30*/ u16 sig_status; + u16 reserved12; + /*34*/ u16 int_status; + u16 reserved13; + /*38*/ u16 reserved14; + u16 reserved15; + /*3C*/ u16 reserved16; + u16 reserved17; + +} BCSR; + +static BCSR * const bcsr = (BCSR *)BCSR_KSEG1_ADDR; + +/* + * Register bit definitions for the BCSRs + */ +#define BCSR_WHOAMI_DCID 0x000F +#define BCSR_WHOAMI_CPLD 0x00F0 +#define BCSR_WHOAMI_BOARD 0x0F00 + +#define BCSR_STATUS_PCMCIA0VS 0x0003 +#define BCSR_STATUS_PCMCIA1VS 0x000C +#define BCSR_STATUS_SWAPBOOT 0x0040 +#define BCSR_STATUS_FLASHBUSY 0x0100 +#define BCSR_STATUS_IDECBLID 0x0200 +#define BCSR_STATUS_SD0WP 0x0400 +#define BCSR_STATUS_SD1WP 0x0800 +#define BCSR_STATUS_U0RXD 0x1000 +#define BCSR_STATUS_U1RXD 0x2000 + +#define BCSR_SWITCHES_OCTAL 0x00FF +#define BCSR_SWITCHES_DIP_1 0x0080 +#define BCSR_SWITCHES_DIP_2 0x0040 +#define BCSR_SWITCHES_DIP_3 0x0020 +#define BCSR_SWITCHES_DIP_4 0x0010 +#define BCSR_SWITCHES_DIP_5 0x0008 +#define BCSR_SWITCHES_DIP_6 0x0004 +#define BCSR_SWITCHES_DIP_7 0x0002 +#define BCSR_SWITCHES_DIP_8 0x0001 +#define BCSR_SWITCHES_ROTARY 0x0F00 + +#define BCSR_RESETS_ETH 0x0001 +#define BCSR_RESETS_CAMERA 0x0002 +#define BCSR_RESETS_DC 0x0004 +#define BCSR_RESETS_IDE 0x0008 +/* not resets but in the same register */ +#define BCSR_RESETS_WSCFSM 0x0800 +#define BCSR_RESETS_PCS0MUX 0x1000 +#define BCSR_RESETS_PCS1MUX 0x2000 +#define BCSR_RESETS_SPISEL 0x4000 +#define BCSR_RESETS_SD1MUX 0x8000 + +#define BCSR_PCMCIA_PC0VPP 0x0003 +#define BCSR_PCMCIA_PC0VCC 0x000C +#define BCSR_PCMCIA_PC0DRVEN 0x0010 +#define BCSR_PCMCIA_PC0RST 0x0080 +#define BCSR_PCMCIA_PC1VPP 0x0300 +#define BCSR_PCMCIA_PC1VCC 0x0C00 +#define BCSR_PCMCIA_PC1DRVEN 0x1000 +#define BCSR_PCMCIA_PC1RST 0x8000 + +#define BCSR_BOARD_LCDVEE 0x0001 +#define BCSR_BOARD_LCDVDD 0x0002 +#define BCSR_BOARD_LCDBL 0x0004 +#define BCSR_BOARD_CAMSNAP 0x0010 +#define BCSR_BOARD_CAMPWR 0x0020 +#define BCSR_BOARD_SD0PWR 0x0040 +#define BCSR_BOARD_SD1PWR 0x0080 + +#define BCSR_LEDS_DECIMALS 0x00FF +#define BCSR_LEDS_LED0 0x0100 +#define BCSR_LEDS_LED1 0x0200 +#define BCSR_LEDS_LED2 0x0400 +#define BCSR_LEDS_LED3 0x0800 + +#define BCSR_SYSTEM_VDDI 0x001F +#define BCSR_SYSTEM_POWEROFF 0x4000 +#define BCSR_SYSTEM_RESET 0x8000 + +/* Bit positions for the different interrupt sources */ +#define BCSR_INT_IDE 0x0001 +#define BCSR_INT_ETH 0x0002 +#define BCSR_INT_PC0 0x0004 +#define BCSR_INT_PC0STSCHG 0x0008 +#define BCSR_INT_PC1 0x0010 +#define BCSR_INT_PC1STSCHG 0x0020 +#define BCSR_INT_DC 0x0040 +#define BCSR_INT_FLASHBUSY 0x0080 +#define BCSR_INT_PC0INSERT 0x0100 +#define BCSR_INT_PC0EJECT 0x0200 +#define BCSR_INT_PC1INSERT 0x0400 +#define BCSR_INT_PC1EJECT 0x0800 +#define BCSR_INT_SD0INSERT 0x1000 +#define BCSR_INT_SD0EJECT 0x2000 +#define BCSR_INT_SD1INSERT 0x4000 +#define BCSR_INT_SD1EJECT 0x8000 + +#define AU1XXX_SMC91111_PHYS_ADDR (0x0D000300) +#define AU1XXX_SMC91111_IRQ PB1200_ETH_INT + +#define AU1XXX_ATA_PHYS_ADDR (0x0C800000) +#define AU1XXX_ATA_PHYS_LEN (0x100) +#define AU1XXX_ATA_REG_OFFSET (5) +#define AU1XXX_ATA_INT PB1200_IDE_INT +#define AU1XXX_ATA_DDMA_REQ DSCR_CMD0_DMA_REQ1; +#define AU1XXX_ATA_RQSIZE 128 + +#define NAND_PHYS_ADDR 0x1C000000 + +/* Timing values as described in databook, * ns value stripped of + * lower 2 bits. + * These defines are here rather than an SOC1200 generic file because + * the parts chosen on another board may be different and may require + * different timings. + */ +#define NAND_T_H (18 >> 2) +#define NAND_T_PUL (30 >> 2) +#define NAND_T_SU (30 >> 2) +#define NAND_T_WH (30 >> 2) + +/* Bitfield shift amounts */ +#define NAND_T_H_SHIFT 0 +#define NAND_T_PUL_SHIFT 4 +#define NAND_T_SU_SHIFT 8 +#define NAND_T_WH_SHIFT 12 + +#define NAND_TIMING ((NAND_T_H & 0xF) << NAND_T_H_SHIFT) | \ + ((NAND_T_PUL & 0xF) << NAND_T_PUL_SHIFT) | \ + ((NAND_T_SU & 0xF) << NAND_T_SU_SHIFT) | \ + ((NAND_T_WH & 0xF) << NAND_T_WH_SHIFT) + + +/* + * External Interrupts for Pb1200 as of 8/6/2004. + * Bit positions in the CPLD registers can be calculated by taking + * the interrupt define and subtracting the PB1200_INT_BEGIN value. + * *example: IDE bis pos is = 64 - 64 + ETH bit pos is = 65 - 64 + */ +#define PB1200_INT_BEGIN (AU1000_LAST_INTC1_INT + 1) +#define PB1200_IDE_INT (PB1200_INT_BEGIN + 0) +#define PB1200_ETH_INT (PB1200_INT_BEGIN + 1) +#define PB1200_PC0_INT (PB1200_INT_BEGIN + 2) +#define PB1200_PC0_STSCHG_INT (PB1200_INT_BEGIN + 3) +#define PB1200_PC1_INT (PB1200_INT_BEGIN + 4) +#define PB1200_PC1_STSCHG_INT (PB1200_INT_BEGIN + 5) +#define PB1200_DC_INT (PB1200_INT_BEGIN + 6) +#define PB1200_FLASHBUSY_INT (PB1200_INT_BEGIN + 7) +#define PB1200_PC0_INSERT_INT (PB1200_INT_BEGIN + 8) +#define PB1200_PC0_EJECT_INT (PB1200_INT_BEGIN + 9) +#define PB1200_PC1_INSERT_INT (PB1200_INT_BEGIN + 10) +#define PB1200_PC1_EJECT_INT (PB1200_INT_BEGIN + 11) +#define PB1200_SD0_INSERT_INT (PB1200_INT_BEGIN + 12) +#define PB1200_SD0_EJECT_INT (PB1200_INT_BEGIN + 13) +#define PB1200_SD1_INSERT_INT (PB1200_INT_BEGIN + 14) +#define PB1200_SD1_EJECT_INT (PB1200_INT_BEGIN + 15) + +#define PB1200_INT_END (PB1200_INT_BEGIN + 15) + +/* For drivers/pcmcia/au1000_db1x00.c */ +#define BOARD_PC0_INT PB1200_PC0_INT +#define BOARD_PC1_INT PB1200_PC1_INT +#define BOARD_CARD_INSERTED(SOCKET) bcsr->sig_status & (1<<(8+(2*SOCKET))) + +#endif /* __ASM_PB1200_H */ + -- cgit 1.2.3-korg