| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: update defconfigs
[PATCH] powerpc: properly configure DDR/P5IOC children devs
[PATCH] powerpc: remove duplicate EXPORT_SYMBOLS
[PATCH] powerpc: RTC memory corruption
[PATCH] powerpc: enable NAP only on cpus who support it to avoid memory corruption
[PATCH] powerpc: Clarify wording for CRASH_DUMP Kconfig option
[PATCH] powerpc/64: enable CONFIG_BLK_DEV_SL82C105
[PATCH] powerpc: correct cacheflush loop in zImage
powerpc: Fix problem with time going backwards
powerpc: Disallow lparcfg being a module
|
|
The dynamic add path for PCI Host Bridges can fail to configure children
adapters under P5IOC controllers. It fails to properly fixup bus/device
resources, and it fails to properly enable EEH. Both of these steps
need to occur before any children devices are enabled in
pci_bus_add_devices().
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Patch from Ben Dooks
The enable_hlt and disable_hlt should be declared in
include/asm/setup.h. This fixes sparse errors from
arch/arm/kernel/process.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] iwmmxt thread state alignment
[ARM] 3350/1: Enable 1-wire on ARM
[ARM] 3356/1: Workaround for the ARM1136 I-cache invalidation problem
[ARM] 3355/1: NSLU2: remove propmt depends
[ARM] 3354/1: NAS100d: fix power led handling
[ARM] Fix muldi3.S
|
|
This patch removes the reliance of iwmmxt on hand coded alignments.
Since thread_info is always 8K aligned, specifying that fpstate is
8-byte aligned achieves the same effect without needing to resort
to hand coded alignments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The patch '[PATCH] RCU signal handling' [1] added an export for
__put_task_struct_cb, a put_task_struct helper newly introduced in that
patch. But the put_task_struct couldn't be used modular previously as
__put_task_struct wasn't exported. There are not callers of it in modular
code, and it shouldn't be exported because we don't want drivers to hold
references to task_structs.
This patch removes the export and folds __put_task_struct into
__put_task_struct_cb as there's no other caller.
[1] http://www2.kernel.org/git/gitweb.cgi?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=e56d090310d7625ecb43a1eeebd479f04affb48b
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch fixes illegal __GFP_FS allocation inside ext3 transaction in
ext3_symlink(). Such allocation may re-enter ext3 code from
try_to_free_pages. But JBD/ext3 code keeps a pointer to current journal
handle in task_struct and, hence, is not reentrable.
This bug led to "Assertion failure in journal_dirty_metadata()" messages.
http://bugzilla.openvz.org/show_bug.cgi?id=115
Signed-off-by: Andrey Savochkin <saw@saw.sw.com.sg>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The cache reaper currently tries to free all alien caches and all remote
per cpu pages in each pass of cache_reap. For a machines with large number
of nodes (such as Altix) this may lead to sporadic delays of around ~10ms.
Interrupts are disabled while reclaiming creating unacceptable delays.
This patch changes that behavior by adding a per cpu reap_node variable.
Instead of attempting to free all caches, we free only one alien cache and
the per cpu pages from one remote node. That reduces the time spend in
cache_reap. However, doing so will lengthen the time it takes to
completely drain all remote per cpu pagesets and all alien caches. The
time needed will grow with the number of nodes in the system. All caches
are drained when they overflow their respective capacity. So the drawback
here is only that a bit of memory may be wasted for awhile longer.
Details:
1. Rename drain_remote_pages to drain_node_pages to allow the specification
of the node to drain of pcp pages.
2. Add additional functions init_reap_node, next_reap_node for NUMA
that manage a per cpu reap_node counter.
3. Add a reap_alien function that reaps only from the current reap_node.
For us this seems to be a critical issue. Holdoffs of an average of ~7ms
cause some HPC benchmarks to slow down significantly. F.e. NAS parallel
slows down dramatically. NAS parallel has a 12-16 seconds runtime w/o rotor
compared to 5.8 secs with the rotor patches. It gets down to 5.05 secs with
the additional interrupt holdoff reductions.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We require that all archs implement atomic_cmpxchg(), for the generic
version of atomic_add_unless().
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix some bugs in mtd/jffs2 on 64bit platform.
The MEMGETBADBLOCK/MEMSETBADBLOCK ioctl are not listed in compat_ioctl.h.
And some variables in jffs2 are declared as uint32_t but used to hold
size_t values.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This is gluing the build of cirrusfb but really the mess that would need
cleaning and fixing is <video/vga.h> and <linux/vt_buffer.h> ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc-merge:
powerpc: Fix various syscall/signal/swapcontext bugs
[PATCH] powerpc: incorrect rmo_top handling in prom_init
[PATCH] powerpc: Fix incorrect pud_ERROR() message
[PATCH] powerpc: Expose SMT and L1 icache snoop userland features
[PATCH] powerpc: Fix windfarm_pm112 not starting all control loops
[PATCH] powerpc: Fix old g5 issues with windfarm
powerpc32: Fix timebase synchronization on 32-bit powermacs
powerpc: Turn off verbose debug output in powermac platform functions
powerpc: Fix might-sleep warning in program check exception handler
|
|
ATI chipsets tend to generate double timer interrupts for the local APIC
timer when both the 8254 and the IO-APIC timer pins are enabled. This is
because they route it to both and the result is anded together and the CPU
ends up processing it twice.
This patch changes check_timer to disable the 8254 routing for interrupt 0.
I think it would be safe on all chipsets actually (i tested it on a couple
and it worked everywhere) and Windows seems to do it in a similar way, but
to be conservative this patch only enables this mode on ATI (and adds
options to enable/disable too)
Ported over from a similar x86-64 change.
I reused the ACPI earlyquirk infrastructure for the ATI bridge check, but
tweaked it a bit to work even without ACPI.
Inspired by a patch from Chuck Ebbert, but redone.
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
While testing kexec and kdump we hit problems where the new kernel would
freeze or instantly reboot. The easiest way to trigger it was to kexec a
kernel compiled for CONFIG_M586 on an athlon cpu. Compiling for CONFIG_MK7
instead would work fine.
The patch fixes a few problems with the kexec inline asm.
Signed-off-by: Chris Mason <mason@suse.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
I have benchmarked this on an x86_64 NUMA system and see no significant
performance difference on kernbench. Tested on both x86_64 and powerpc.
The way we do file struct accounting is not very suitable for batched
freeing. For scalability reasons, file accounting was
constructor/destructor based. This meant that nr_files was decremented
only when the object was removed from the slab cache. This is susceptible
to slab fragmentation. With RCU based file structure, consequent batched
freeing and a test program like Serge's, we just speed this up and end up
with a very fragmented slab -
llm22:~ # cat /proc/sys/fs/file-nr
587730 0 758844
At the same time, I see only a 2000+ objects in filp cache. The following
patch I fixes this problem.
This patch changes the file counting by removing the filp_count_lock.
Instead we use a separate percpu counter, nr_files, for now and all
accesses to it are through get_nr_files() api. In the sysctl handler for
nr_files, we populate files_stat.nr_files before returning to user.
Counting files as an when they are created and destroyed (as opposed to
inside slab) allows us to correctly count open files with RCU.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds new tunables for RCU queue and finished batches. There are
two types of controls - number of completed RCU updates invoked in a batch
(blimit) and monitoring for high rate of incoming RCUs on a cpu (qhimark,
qlowmark).
By default, the per-cpu batch limit is set to a small value. If the input
RCU rate exceeds the high watermark, we do two things - force quiescent
state on all cpus and set the batch limit of the CPU to INTMAX. Setting
batch limit to INTMAX forces all finished RCUs to be processed in one shot.
If we have more than INTMAX RCUs queued up, then we have bigger problems
anyway. Once the incoming queued RCUs fall below the low watermark, the
batch limit is set to the default.
Signed-off-by: Dipankar Sarma <dipankar@in.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Implement percpu_counter_sum(). This is a more accurate but slower version of
percpu_counter_read_positive().
We need this for Alex's speedup-ext3_statfs patch and for the nr_file
accounting fix. Otherwise these things would be too inaccurate on large CPU
counts.
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Cc: Alex Tomas <alex@clusterfs.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If the 'ptr' is a const, this code cause "assignment of read-only variable"
error on gcc 4.x.
Use __u64 instead of __typeof__(*(ptr)) for temporary variable to get
rid of errors on gcc 4.x.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We fixed this:
arch/powerpc/platforms/pseries/eeh.c: In function `eeh_add_device_tree_late':
arch/powerpc/platforms/pseries/eeh.c:901: warning: implicit declaration of function `eeh_add_device_late'
arch/powerpc/platforms/pseries/eeh.c: At top level:
arch/powerpc/platforms/pseries/eeh.c:918: error: conflicting types for 'eeh_add_device_late'
arch/powerpc/platforms/pseries/eeh.c:901: error: previous implicit declaration of 'eeh_add_device_late' was here
make[2]: *** [arch/powerpc/platforms/pseries/eeh.o] Error 1
But we forgot the !CONFIG_EEH stub.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
They aren't used (nor even really usable) outside of pipe.c anyway
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
A careful reading of the recent changes to the system call entry/exit
paths revealed several problems, plus some things that could be
simplified and improved:
* 32-bit wasn't testing the _TIF_NOERROR bit in the syscall fast exit
path, so it was only doing anything with it once it saw some other
bit being set. In other words, the noerror behaviour would apply to
the next system call where we had to reschedule or deliver a signal,
which is not necessarily the current system call.
* 32-bit wasn't doing the call to ptrace_notify in the syscall exit
path when the _TIF_SINGLESTEP bit was set.
* _TIF_RESTOREALL was in both _TIF_USER_WORK_MASK and
_TIF_PERSYSCALL_MASK, which is odd since _TIF_RESTOREALL is only set
by system calls. I took it out of _TIF_USER_WORK_MASK.
* On 64-bit, _TIF_RESTOREALL wasn't causing the non-volatile registers
to be restored (unless perhaps a signal was delivered or the syscall
was traced or single-stepped). Thus the non-volatile registers
weren't restored on exit from a signal handler. We probably got
away with it mostly because signal handlers written in C wouldn't
alter the non-volatile registers.
* On 32-bit I simplified the code and made it more like 64-bit by
making the syscall exit path jump to ret_from_except to handle
preemption and signal delivery.
* 32-bit was calling do_signal unnecessarily when _TIF_RESTOREALL was
set - but I think because of that 32-bit was actually restoring the
non-volatile registers on exit from a signal handler.
* I changed the order of enabling interrupts and saving the
non-volatile registers before calling do_syscall_trace_leave; now we
enable interrupts first.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
Patch from Catalin Marinas
Chapter B2.7.3 in the latest ARM ARM (with v6 information) states that
the completion of a TLB maintenance operation is only guaranteed by
the execution of a DSB (Data Syncronization Barrier, formerly Data
Write Barrier or Drain Write Buffer).
Note that a DSB is only needed in the flush_tlb_kernel_* functions
since the completion is guaranteed by a mode change (i.e. switching
back to user mode) for the flush_tlb_user_* functions.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Systems with extemely large numbers of nodes or cpus need to kmalloc
structures larger than is currently supported. This patch increases the
maximum supported size for very large systems.
This patch should have no effect on current systems.
(akpm: why not just use alloc_pages() for sysfs_cpus?)
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
include/linux/memory_hotplug.h:53: warning: 'struct page' declared inside parameter list
(akpm: I tossed in a couple more possibly-needed-sometime struct decls too)
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
When CONFIG_VIRT_CPU_ACCOUNTING is not defined compiling fails with an
undefined reference to account_vtime().
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Also from Thomas Gleixner <tglx@linutronix.de>
Function next_timer_interrupt() got broken with a recent patch
6ba1b91213e81aa92b5cf7539f7d2a94ff54947c as sys_nanosleep() was moved to
hrtimer. This broke things as next_timer_interrupt() did not check hrtimer
tree for next event.
Function next_timer_interrupt() is needed with dyntick (CONFIG_NO_IDLE_HZ,
VST) implementations, as the system can be in idle when next hrtimer event
was supposed to happen. At least ARM and S390 currently use
next_timer_interrupt().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add new PCI IDs for HFC-S PCI based ISDN TA 'Primux II S0' and 'Primux II S0'
from Gerdes AG
Signed-off-by: Martin Bachem <info@colognechip.com>
Signed-off-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We must use the "a" (allocate) attribute every time we
emit an entry into the __ex_table section.
For consistency, use "a" instead of #alloc which is some
Solaris compat cruft GNU as provides on Sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The powerpc pud_ERROR() function misleadingly prints a message
indicating a pmd error. This patch fixes it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch makes userland aware of the icache snoop capability of the
POWER5 (and possibly others in the future) and of SMT capabilities.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The bitmaps associated with generation numbers for directory entries
are declared as an array of ints. On some platforms, this causes alignment
exceptions.
The following patch uses the standard bitmap declaration macros to
declare the bitmaps, fixing the problem.
Originally from Takashi Iwai.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
This patch should fixe a problem with eeh_add_device_late() not being
defined in the ppc64 build process, causing the build to break.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
vendor string
This is needed to distinguish Intersil and non-Intersil cards with
numeric ID 0x0156, 0x0002.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
|
|
This patch adds mm->task_size to keep track of the task size of a given mm
and uses that to fix the powerpc vdso so that it uses the mm task size to
decide what pages to fault in instead of the current thread flags (which
broke when ptracing).
(akpm: I expect that mm_struct.task_size will become the way in which we
finally sort out the confusion between 32-bit processes and 32-bit mm's. It
may need tweaks, but at this stage this patch is powerpc-only.)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Allow sysadmin to disable all warnings about userland apps
making unaligned accesses by using:
# echo 1 > /proc/sys/kernel/ignore-unaligned-usertrap
Rather than having to use prctl on a process by process basis.
Default behaivour leaves the warnings enabled.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Some hotplug driver functions were migrated to the kernel for use by EEH
in commit 2bf6a8fa21570f37fd1789610da30f70a05ac5e3.
Previously, the PCI Hotplug module had been changed to use the new
OFDT-based PCI probe when appropriate:
5fa80fcdca9d20d30c9ecec30d4dbff4ed93a5c6
When rpaphp_pci_config_slot() was moved from the rpaphp driver to the
new kernel function pcibios_add_pci_devices(), the OFDT-based probe
stuff was dropped. This patch restores it.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
TSC assumption on IBM systems"
This reverts commit 13a229abc25640813f1480c0478dfc6bdbc1c19e.
Quoth Andi:
"After some consideration and feedback from various people it turns
out this wasn't that good an idea. It has some problems and needs
more work. Since it was only an optimization anyways it's best to
just back it out again for now."
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make the limit for the number of TIO nodes a function of the number
of C/M nodes in the system instead of a hardcoded constant. The
number of TIO nodes should be the same as the number of C/M nodes.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The nfnetlink_log infrastructure changes broke compatiblity of the LOG
targets. They currently use whatever log backend was registered first,
which means that if ipt_ULOG was loaded first, no messages will be printed
to the ring buffer anymore.
Restore compatiblity by using the old log functions by default and only use
the nf_log backend if the user explicitly said so.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only reason post_input exists at all is that it gives us the
potential to adjust the checksums incrementally in future which
we ought to do.
However, after thinking about it for a bit we can adjust the
checksums without using this post_input stuff at all. The crucial
point is that only the inner-most NAT-T SA needs to be considered
when adjusting checksums. What's more, the checksum adjustment
comes down to a single u32 due to the linearity of IP checksums.
We just happen to have a spare u32 lying around in our skb structure :)
When ip_summed is set to CHECKSUM_NONE on input, the value of skb->csum
is currently unused. All we have to do is to make that the checksum
adjustment and voila, there goes all the post_input and decap structures!
I've left in the decap data structures for now since it's intricately
woven into the sec_path stuff. We can kill them later too.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported and initial fix by Thomas Koeller <thomas.koeller@baslerweb.com>,
rewritten by me.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
A recent change requires cpu_possible_map to be initialized before
smp_sched_init() but most MIPS platforms were initializing their
processors in the prom_prepare_cpus callback of smp_prepare_cpus. The
simple fix of calling prom_prepare_cpus from one of the earlier SMP
initialization hooks doesn't work well either since IPIs may require
init_IRQ() to have completed, so bit the bullet and split
prom_prepare_cpus into two initialization functions, plat_smp_setup
which is called early from setup_arch and plat_prepare_cpus called where
prom_prepare_cpus used to be called.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The change to kernel/sched.c's init code to use for_each_cpu()
requires that the cpu_possible_map be setup much earlier.
Set it up via setup_arch(), constrained to NR_CPUS, and later
constrain it to max_cpus in smp_prepare_cpus().
This fixes SMP booting on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMP time selection originally ran after all CPUs were brought up because
it needed to know the number of CPUs to decide if it needs an MP safe
timer or not.
This is not needed anymore because we know present CPUs early.
This fixes a couple of problems:
- apicmaintimer didn't always work because it relied on state that was
set up time_init_gtod too late.
- The output for the used timer in early kernel log was misleading
because time_init_gtod could actually change it later. Now always
print the final timer choice
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It didn't set up the CPU possible map early enough, so the
option didn't actually work.
Noticed by Heiko Carstens
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
assumption on IBM systems
Big Unisys systems have multiple clusters too, but they have an
synchronized TSC.
I'm using the SMBIOS to check for vendor == IBM.
Cc: Chris McDermott <lcm@us.ibm.com>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The value, while currently unused in the native kernel, was off by one.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In previous versions of pci-gart.c, no_iommu was used to determine if IOMMU was
disabled in the GART DMA mapping functions. This changed in 2.6.16 and now
gart_xxx() functions are only called if gart is enabled. Therefore, uses of
no_iommu in the GART code are no longer necessary and can be removed.
Also, it removes double deceleration of no_iommu and force_iommu in pci.h and
proto.h, by removing the deceleration in pci.h.
Lastly, end_pfn off by one error.
Tested (along with patch 1/2) on dual opteron with gart enabled, iommu=soft,
and iommu=off.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
I'm currently at the POSIX meeting and one thing covered was the
incompatibility of Linux's link() with the POSIX definition. The name.
Linux does not follow symlinks, POSIX requires it does.
Even if somebody thinks this is a good default behavior we cannot change this
because it would break the ABI. But the fact remains that some application
might want this behavior.
We have one chance to help implementing this without breaking the behavior.
For this we could use the new linkat interface which would need a new
flags parameter. If the new parameter is AT_SYMLINK_FOLLOW the new
behavior could be invoked.
I do not want to introduce such a patch now. But we could add the
parameter now, just don't use it. The patch below would do this. Can we
get this late patch applied before the release more or less fixes the
syscall API?
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Recent GDT changes broke the SMP boot sequence if the booting CPU is
numbered anything other than zero. There's also a subtle source of error
in that the boot time CPU now uses cpu_gdt_table (which is actually the GDT
for booting CPUs in head.S). This patch fixes both problems by making GDT
descriptors themselves allocated from a per_cpu area and switching to them
in cpu_init(), which now means that cpu_gdt_table is exclusively used for
booting CPUs again.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Zachary Amsden <zach@vmware.com>
Cc: Matt Tolentino <metolent@snoqualmie.dp.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix a problem seen on i686 machine with NX support where the instruction
could not be single stepped because of NX bit set on the memory pages
allocated by kprobes module. This patch provides allocation of instruction
solt so that the processor can execute the instruction from that location
similar to x86_64 architecture. Thanks to Bibo and Masami for testing this
patch.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix and update for gcc-4.0.
- arch/m32r/kernel/signal.c:
Change type of the 8th parameter of sys_rt_sigsuspend() from
'struct pt_regs' to 'struct pt_regs *'.
This functions make use of the 'regs' parameter to return status value,
but gcc-4.0 optimizes and removes it as a dead code.
Functions, sys_sigaltstack() and sys_rt_sigreturn(), have also modified.
- arch/m32r/lib/usercopy.c, include/asm-m32r/uaccess.h:
Add early-clobber constraints('&') to output values of asm statements;
these constraints seems to be required for gcc-4.0 register assignment.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
The runlatch SPR can take a lot of time to write. My original runlatch
code would set it on every exception entry even though most of the time
this was not required. It would also continually set it in the idle
loop, which is an issue on an SMT capable processor.
Now we cache the runlatch value in a threadinfo bit, and only check for
it in decrementer and hardware interrupt exceptions as well as the idle
loop. Boot on POWER3, POWER5 and iseries, and compile tested on pmac32.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
corruption
On the 83xx platform to ensure the PCI inbound memory is handled properly we
have to turn on coherency for all pages in the MMU. Otherwise we see
corruption if inbound "prefetching/streaming" is enabled on the PCI controller.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
For kexec we need to know the size of the MMU hash table.
Currently we calculate the size once in the htab code, and then twice more in
the kexec code, once using htab_hash_mask and once using ppc64_pft_size.
On some machines the ppc64_pft_size calculation is broken because
ppc64_pft_size is not set.
So we need to fix the second calculation, but better still we should just
calculate the size once and use it everywhere else.
Tested on Power5 LPAR, Power4 non-LPAR and Power3.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We often just do an atomic_dec(&x->refcnt) on an xfrm_state object
because we know there is more than 1 reference remaining and thus
we can elide the heavier xfrm_state_put() call.
Do this behind an inline function called __xfrm_state_put() so that is
more obvious and also to allow us to more cleanly add refcount
debugging later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial comment fix for include/linux/serial_reg.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
|
|
Patch from Andrew Victor
This patch adds the at91_set_multi_drive() function to enable/disable
the multi-drive (open collector) pin capability on the AT91RM9200
processor.
This is necessary to fix the UDC (USB Gadget) driver for the AT91RM9200
board as it will not allow the board reset line to be pulled low if the
pullup is not driven as an open collector output as the boards are wired
to the USB connector on both the DK/EK.
This version of the patch updates it to 2.6.16-rc4.
Orignal patch by Jeff Warren.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Alessandro Zummo
The I2C pin assignment for the Iomega NAS100d board was incorrect. This
patch fixes it. The correct assignment has now been tested using the
new RTC class and a new driver for the RTC on the NAS100d.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This change reverts the 033b96fd30db52a710d97b06f87d16fc59fee0f1 commit
from Kay Sievers that removed the mount/umount uevents from the kernel.
Some older versions of HAL still depend on these events to detect when a
new device has been mounted. These events are not correctly emitted,
and are broken by design, and so, should not be relied upon by any
future program. Instead, the /proc/mounts file should be polled to
properly detect this kind of event.
A feature-removal-schedule.txt entry has been added, noting when this
interface will be removed from the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
It's MMC_CMD_MASK not MMC_CMD_TYPE.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
|
|
(This really is only the half of the patch which was forgotten in
326a625748535c4cdb1c632b1dcb07030989a393 ...)
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
It seems current get_user() incorrectly sign-extend an unsigned int
value on 64bit kernel. I think this is because '(__typeof__(val))'
cast in final assignment. I suppose the cast should be
'(__typeof__(*(addr))'.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/bird
|
|
|
|
This patch fixes a bug of include/asm-m32r/system.h:__cmpxchg_u32().
static __inline__ unsigned long
__cmpxchg_u32(volatile unsigned int *p, unsigned int old, unsigned int new);
In __cmpxchg_u32(), the "old" value must not be changed to the previous "*p"
value. But the former code modifies the previous "*p" value.
A deadlock at _atomic_dec_and_lock sometimes happened due to this bug.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Revert dasd eer module until we have a common understanding of how the
interface should be.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The compat syscalls are added to sys_ni.c since they are not defined if the
above CONFIG options are off. Also, nfs would not build with CONFIG_SYSCTL
off.
Noticed by Arthur Othieno.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Luke Yang <luke.adi@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently, acpi video options can only be set on kernel command line. That's
little inflexible; I'd like userland s2ram application that just works, and
modifying kernel command line according to whitelist is not fun. It is better
to just allow s2ram application to set video options just before suspend
(according to the whitelist).
This implements sysctl to allow setting suspend video options without reboot.
(akpm: Documentation updates for this new sysctl are pending..)
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: "Brown, Len" <len.brown@intel.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Some allocations are restricted to a limited set of nodes (due to memory
policies or cpuset constraints). If the page allocator is not able to find
enough memory then that does not mean that overall system memory is low.
In particular going postal and more or less randomly shooting at processes
is not likely going to help the situation but may just lead to suicide (the
whole system coming down).
It is better to signal to the process that no memory exists given the
constraints that the process (or the configuration of the process) has
placed on the allocation behavior. The process may be killed but then the
sysadmin or developer can investigate the situation. The solution is
similar to what we do when running out of hugepages.
This patch adds a check before we kill processes. At that point
performance considerations do not matter much so we just scan the zonelist
and reconstruct a list of nodes. If the list of nodes does not contain all
online nodes then this is a constrained allocation and we should kill the
current process.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch makes ata_for_each_sg() start with pad_sgent when
qc->n_elem is zero. Previously, ata_for_each_sg() unconditionally
started with qc->__sg, handling the first sg to fill_sg() routines
even when the entry was invalid. And while at it, unwind ?: in
ata_qc_next_sg() into if statement.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
|
|
A few symbols are exported twice, remove them from ppc_ksyms.c
Remove users of sys_ctrler in arch/ppc/
WARNING: vmlinux: duplicate symbol '__delay' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__up' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol '__down_interruptible' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'sys_ctrler' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncat' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strncmp' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strrchr' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strnlen' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strpbrk' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'memscan' previous definition was in vmlinux
WARNING: vmlinux: duplicate symbol 'strstr' previous definition was in vmlinux
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
added __raw_writel(), sanitized include order in iomap_copy.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Patch claiming to remove enable_irq_nosync() had left it alive but killed
disable_irq_nosync() instead...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
One of the parameters to the __pud_free_tlb() macro for powerpc is
incorrect (see patch) . We get away with it by accident, because the one
place the macro is called, the second parameter is a variable named "pud".
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Introduce additional_cpus command line option. By default no additional cpu
can be attached to the system anymore. Only the cpus present at IPL time can
be switched on/off. If it is desired that additional cpus can be attached to
the system the maximum number of additional cpus needs to be specified with
this option.
This change is necessary in order to limit the waste of per_cpu data
structures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Do not mask TIF_SINGLESTEP bit in _TIF_WORK_MASK. Masking this stopped
do_notify_resume() from being called when it should have been.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This provides an interface for arch code to find out how many
nanoseconds are going to be added on to xtime by the next call to
do_timer. The value returned is a fixed-point number in 52.12 format
in nanoseconds. The reason for this format is that it gives the
full precision that the timekeeping code is using internally.
The motivation for this is to fix a problem that has arisen on 32-bit
powerpc in that the value returned by do_gettimeofday drifts apart
from xtime if NTP is being used. PowerPC is now using a lockless
do_gettimeofday based on reading the timebase register and performing
some simple arithmetic. (This method of getting the time is also
exported to userspace via the VDSO.) However, the factor and offset
it uses were calculated based on the nominal tick length and weren't
being adjusted when NTP varied the tick length.
Note that 64-bit powerpc has had the lockless do_gettimeofday for a
long time now. It also had an extremely hairy routine that got called
from the 32-bit compat routine for adjtimex, which adjusted the
factor and offset according to what it thought the timekeeping code
was going to do. Not only was this only called if a 32-bit task did
adjtimex (i.e. not if a 64-bit task did adjtimex), it was also
duplicating computations from kernel/timer.c and it wasn't clear that
it was (still) correct.
The simple solution is to ask the timekeeping code how long the
current jiffy will be on each timer interrupt, after calling
do_timer. If this jiffy will be a different length from the last one,
we then need to compute new values for the factor and offset used in
the lockless do_gettimeofday. In this way we can keep xtime and
do_gettimeofday in sync, even when NTP is varying the tick length.
Note that when adjtimex varies the tick length, it almost always
introduces the variation from the next tick on. The only case I could
see where adjtimex would vary the length of the current tick is when
an old-style adjtime adjustment is being cancelled. (It's not clear
to me why the adjustment has to be cancelled immediately rather than
from the next tick on.) Thus I don't see any real need for a hook in
adjtimex; the rare case of an old-style adjustment being cancelled can
be fixed up at the next tick.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: john stultz <johnstul@us.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
|
|
|
|
Otherwise it has no effect anyways.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
AMD SimNow!'s JIT doesn't like them at all in the guest. For distribution
installation it's easiest if it's a boot time option.
Also I moved the variable to a more appropiate place and make
it independent from sysctl
And marked __read_mostly which it is.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Patch from Nicolas Pitre
With EABI the multiplex sys_ipc and sys_socketcall syscalls are
unavailable and their support code even removed from the compiled
kernel, and the new unmuxed syscalls must be used instead.
Make those syscall numbers visible.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
A change to the SMP initialisation caused the following oops:
CPU1: Booted secondary processor
CPU1: D VIPT write-back cache
CPU1: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
CPU1: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
<7>Calibrating delay loop... 83.14 BogoMIPS (lpj=415744)
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000001c
...
PC is at enqueue_task+0x1c/0x64
LR is at activate_task+0xcc/0xe4
SMP initialisation now requires cpu_possible_map to be initialised in
setup_arch(). Move this from smp_prepare_cpus() to smp_init_cpus()
and call it from our setup_arch() if CONFIG_SMP is enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
For two macros the arguments were expanded twice, change them to inline
functions to avoid it.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make new MADV_REMOVE, MADV_DONTFORK, MADV_DOFORK consistent across all
arches. The idea is to make it possible to use them portably even before
distros include them in libc headers.
Move common flags to asm-generic/mman.h
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
There were two mistakes in the register-read-on-(un)blank approach.
- First, without proper register (un)locking the value read back will always
be zero, and this is what I missed entirely until just now. Due to this,
the logic could not be verified at all and I tried some bogus checks which
are completely stupid.
- Second, the LCD status bit will always be set to zero when the backlight
has been turned off. Reading the value back during unblank will disable the
LCD unconditionally, regardless of the state it is supposed to be in, since
we set it to zero beforehand.
So this is what we do now:
- create a new variable in struct neofb_par, and use that to determine
whether to read back registers (initialized to true)
- before actually blanking the screen, read back the register to sense any
possible change made through Fn key combo
- use proper neoUnlock() / neoLock() to actually read something
- every call to neofb_blank() determines if we read back next time: blanking
disables readback, unblanking (FB_BLANK_UNBLANK) enables it
This should give us a nice and clean state machine. Has been thoroughly
tested on a Dell Latitude CPiA / NM220 Chip docked to a C/Dock2 with attached
CRT in all possible combinations of LCD/CRT on/off. I changed the config via
Fn key, let the console blank, unblanked by keypress - works flawlessly.
Signed-off-by: Christian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
nf_hook() is supposed to call the netfilter hook and return control of the
packet back to the caller in case it may pass, the okfn is only used for
queueing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When a packet matching an IPsec policy is SNATed so it doesn't match any
policy anymore it looses its xfrm bundle, which makes xfrm4_output_finish
crash because of a NULL pointer dereference.
This patch directs these packets to the original output path instead. Since
the packets have already passed the POST_ROUTING hook, but need to start at
the beginning of the original output path which includes another
POST_ROUTING invocation, a flag is added to the IPCB to indicate that the
packet was rerouted and doesn't need to pass the POST_ROUTING hook again.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original ia64 udelay() was simple, but flawed for platforms without
synchronized ITCs: a preemption and migration to another CPU during the
while-loop likely resulted in too-early termination or very, very
lengthy looping.
The first fix (now in 2.6.15) broke the delay loop into smaller,
non-preemptible chunks, reenabling preemption between the chunks. This
fix is flawed in that the total udelay is computed to be the sum of just
the non-premptible while-loop pieces, i.e., not counting the time spent
in the interim preemptible periods. If an interrupt or a migration
occurs during one of these interim periods, then that time is invisible
and only serves to lengthen the effective udelay().
This new fix backs out the current flawed fix and returns to a simple
udelay(), fully preemptible and interruptible. It implements two simple
alternative udelay() routines: one a default generic version that uses
ia64_get_itc(), and the other an sn-specific version that uses that
platform's RTC.
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Fix XPC so that it does not deliver any messages until the connected
callout has returned, as well as, prevent the disconnected callout to
occur before the disconnecting callout has returned.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
The __sn_cnodeid_to_nasid array was incorrectly sized at MAX_NUMNODES.
On a large system, this array could overflow. The following patch
corrects this by defining it to MAX_COMPACT_NODES.
Signed-off-by: Dean Roe <roe@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Remove obsolete SGI address
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
General SN2 code cleanup:
- Do not initialize global variables to zero
- Use kzalloc instead of kmalloc+memset
- Check kmalloc return values
- Do not obfuscate spin lock calls
- Remove some unused code
- Various formatting cleanups
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
1. The tracee can go from ptrace_stop() to do_signal_stop()
after __ptrace_unlink(p).
2. It is unsafe to __ptrace_unlink(p) while p->parent may wait
for tasklist_lock in ptrace_detach().
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
To find out if a packet needs to be handled by IPsec after SNAT, packets
are currently rerouted in POST_ROUTING and a new xfrm lookup is done. This
breaks SNAT of non-unicast packets to non-local addresses because the
packet is routed as incoming packet and no neighbour entry is bound to the
dst_entry. In general, it seems to be a bad idea to replace the dst_entry
after the packet was already sent to the output routine because its state
might not match what's expected.
This patch changes the xfrm lookup in POST_ROUTING to re-use the original
dst_entry without routing the packet again. This means no policy routing
can be used for transport mode transforms (which keep the original route)
when packets are SNATed to match the policy, but it looks like the best
we can do for now.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the FRV arch use virtual interrupt disablement because accesses to the
processor status register (PSR) are relatively slow and because we will
soon have the need to deal with multiple interrupt controls at the same
time (separate h/w and inter-core interrupts).
The way this is done is to dedicate one of the four integer condition code
registers (ICC2) to maintaining a virtual interrupt disablement state
whilst inside the kernel. This uses the ICC2.Z flag (Zero) to indicate
whether the interrupts are virtually disabled and the ICC2.C flag (Carry)
to indicate whether the interrupts are physically disabled.
ICC2.Z is set to indicate interrupts are virtually disabled. ICC2.C is set
to indicate interrupts are physically enabled. Under normal running
conditions Z==0 and C==1.
Disabling interrupts with local_irq_disable() doesn't then actually
physically disable interrupts - it merely sets ICC2.Z to 1. Should an
interrupt then happen, the exception prologue will note ICC2.Z is set and
branch out of line using one instruction (an unlikely BEQ). Here it will
physically disable interrupts and clear ICC2.C.
When it comes time to enable interrupts (local_irq_enable()), this simply
clears the ICC2.Z flag and invokes a trap #2 if both Z and C flags are
clear (the HI integer condition). This can be done with the TIHI
conditional trap instruction.
The trap then physically reenables interrupts and sets ICC2.C again. Upon
returning the interrupt will be taken as interrupts will then be enabled.
Note that whilst processing the trap, the whole exceptions system is
disabled, and so an interrupt can't happen till it returns.
If no pending interrupt had happened, ICC2.C would still be set, the HI
condition would not be fulfilled, and no trap will happen.
Saving interrupts (local_irq_save) is simply a matter of pulling the ICC2.Z
flag out of the CCR register, shifting it down and masking it off. This
gives a result of 0 if interrupts were enabled and 1 if they weren't.
Restoring interrupts (local_irq_restore) is then a matter of taking the
saved value mentioned previously and XOR'ing it against 1. If it was one,
the result will be zero, and if it was zero the result will be non-zero.
This result is then used to affect the ICC2.Z flag directly (it is a
condition code flag after all). An XOR instruction does not affect the
Carry flag, and so that bit of state is unchanged. The two flags can then
be sampled to see if they're both zero using the trap (TIHI) as for the
unconditional reenablement (local_irq_enable).
This patch also:
(1) Modifies the debugging stub (break.S) to handle single-stepping crossing
into the trap #2 handler and into virtually disabled interrupts.
(2) Removes superseded fixup pointers from the second instructions in the trap
tables (there's no a separate fixup table for this).
(3) Declares the trap #3 vector for use in .org directives in the trap table.
(4) Moves irq_enter() and irq_exit() in do_IRQ() to avoid problems with
virtual interrupt handling, and removes the duplicate code that has now
been folded into irq_exit() (softirq and preemption handling).
(5) Tells the compiler in the arch Makefile that ICC2 is now reserved.
(6) Documents the in-kernel ABI, including the virtual interrupts.
(7) Renames the old irq management functions to different names.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make various alterations and fixes to the FRV arch:
(1) Resyncs the FRV system call collection with the i386 arch.
(2) Discards __iounmap() as it's not used.
(3) Fixes the use of the SWAP/SWAPI instruction to get the arguments the right
way around in atomic.h, and also to get the asm constraints correct.
(4) Moves copy_to/from_user_page() to asm/cacheflush.h to be consistent with
other archs.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Revert commit d7102e95b7b9c00277562c29aad421d2d521c5f6:
[PATCH] sched: filter affine wakeups
Apparently caused more than 10% performance regression for aim7 benchmark.
The setup in use is 16-cpu HP rx8620, 64Gb of memory and 12 MSA1000s with 144
disks. Each disk is 72Gb with a single ext3 filesystem (courtesy of HP, who
supplied benchmark results).
The problem is, for aim7, the wake-up pattern is random, but it still needs
load balancing action in the wake-up path to achieve best performance. With
the above commit, lack of load balancing hurts that workload.
However, for workloads like database transaction processing, the requirement
is exactly opposite. In the wake up path, best performance is achieved with
absolutely zero load balancing. We simply wake up the process on the CPU that
it was previously run. Worst performance is obtained when we do load
balancing at wake up.
There isn't an easy way to auto detect the workload characteristics. Ingo's
earlier patch that detects idle CPU and decide whether to load balance or not
doesn't perform with aim7 either since all CPUs are busy (it causes even
bigger perf. regression).
Revert commit d7102e95b7b9c00277562c29aad421d2d521c5f6, which causes more
than 10% performance regression with aim7.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently, copy-on-write may change the physical address of a page even if the
user requested that the page is pinned in memory (either by mlock or by
get_user_pages). This happens if the process forks meanwhile, and the parent
writes to that page. As a result, the page is orphaned: in case of
get_user_pages, the application will never see any data hardware DMA's into
this page after the COW. In case of mlock'd memory, the parent is not getting
the realtime/security benefits of mlock.
In particular, this affects the Infiniband modules which do DMA from and into
user pages all the time.
This patch adds madvise options to control whether memory range is inherited
across fork. Useful e.g. for when hardware is doing DMA from/into these
pages. Could also be useful to an application wanting to speed up its forks
by cutting large areas out of consideration.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The correct way to export hyperthreading based functions is to predicate
them on CONFIG_X86_HT. Without this, the topology exporting patch breaks
the build on all non-PC x86 subarchitectures.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If 2 threads attached to the same process are blocking on different locks on
different files (maybe even on different servers) but have the same lock
arguments (i.e. same offset+length - actually quite common, since most
processes try to lock the entire file) then the first GRANTED call that wakes
one up will also wake the other.
Currently when the NLM_GRANTED callback comes in, lockd walks the list of
blocked locks in search of a match to the lock that the NLM server has
granted. Although it checks the lock pid, start and end, it fails to check
the filehandle and the server address.
By checking the filehandle and server IP address, we ensure that this only
happens if the locks truly are referencing the same file.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch reverts commit f93ea411b73594f7d144855fd34278bcf34a9afc:
[PATCH] jbd: split checkpoint lists
This broke journal_flush() for OCFS2, which is its method of being sure
that metadata is sent to disk for another node.
And two related commits 8d3c7fce2d20ecc3264c8d8c91ae3beacdeaed1b and
43c3e6f5abdf6acac9b90c86bf03f995bf7d3d92 with the subjects:
[PATCH] jbd: log_do_checkpoint fix
[PATCH] jbd: remove_transaction fix
These seem to be incremental bugfixes on the original patch and as such are
no longer needed.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Jan Kara <jack@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Have a facility to account for potentially hot-pluggable CPUs. ACPI doesnt
give a determinstic method to find hot-pluggable CPUs. Hence we use 2 methods
to assist.
- BIOS can mark potentially hot-pluggable CPUs as disabled in the MADT tables.
- User can specify the number of hot-pluggable CPUs via parameter
additional_cpus=X
The option is enabled only if ACPI_CONFIG_HOTPLUG_CPU=y which enables the
physical hotplug option. Without which user can still use logical onlining
and offlining of CPUs by enabling CONFIG_HOTPLUG_CPU=y
Adds more bits to cpu_possible_map for potentially hot-pluggable cpus.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
From Richard Sandiford <richard@codesourcery.com>:
This patch caused a miscompilation of the restore_gp_regs() block
in restore_sigcontext(). This was in a 32-bit kernel compiled with
GCC CVS head.
restore_gp_regs() copies 64-bit user fields into 32-bit variables,
and in this combination, the new __get_user_asm_ll32() clobbers too
many registers. It says:
/*
* Get a long long 64 using 32 bit registers.
*/
{ \
__asm__ __volatile__( \
"1: lw %1, (%3) \n" \
"2: lw %D1, 4(%3) \n" \
" move %0, $0 \n" \
"3: .section .fixup,\"ax\" \n" \
"4: li %0, %4 \n" \
" move %1, $0 \n" \
" move %D1, $0 \n" \
" j 3b \n" \
" .previous \n" \
" .section __ex_table,\"a\" \n" \
" " __UA_ADDR " 1b, 4b \n" \
" " __UA_ADDR " 2b, 4b \n" \
" .previous \n" \
: "=r" (__gu_err), "=&r" (val) \
: "0" (0), "r" (addr), "i" (-EFAULT)); \
}
and this requires val (%1) to be a 64-bit value. In the case I saw,
gcc was using $3 for the 32-bit val, and wasn't expecting $4 to be
clobbered.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add blast_xxx_range(), protected_blast_xxx_range() etc. for common
use. They are built by __BUILD_BLAST_CACHE_RANGE().
Use protected_cache_op() macro for various protected_ routines.
Output code should be logically same.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
So we can get rid of config.h and the #ifdef crapola in the generic
timex.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
We have several points in the SCSI stack (primarily for our device
functions) where we need to guarantee process context, but (given the
place where the last reference was released) we cannot guarantee this.
This API gets around the issue by executing the function directly if
the caller has process context, but scheduling a workqueue to execute
in process context if the caller doesn't have it. Unfortunately, it
requires memory allocation in interrupt context, but it's better than
what we have previously. The true solution will require a bit of
re-engineering, so isn't appropriate for 2.6.16.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
|
|
|
|
From: Joe Perches <joe@perches.com>
Based upon a patch by Dave Jones.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reduces the default L2CAP MTU for all RFCOMM connections
from 1024 to 1013 to improve the interoperability with some broken
RFCOMM implementations. To make this more flexible the L2CAP MTU
becomes also a module parameter and so it can changed at runtime.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add fstatat64 support to s390 in order to follow changes with
commit cff2b760096d1e6feaa31948e7af4abbefe47822 .
Also fixes compilation for 31 bit.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add support for Geforce4 MX 4000 (0x185)
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Right now in __constant_test_bit for the s390 there is an extra set of ()
surrounding the calculation. This patch simply removes one set of () that is
surrounding the whole clause.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Based on a patch from Maximilian Attems <maks@sternwelten.at> . Nothing in
asm-s390/setup.h is of interest for user space.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add support for unshare system call.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add missing smp_cpu_not_running define to avoid build warnings in the non smp
case.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With David Woodhouse <dwmw2@infradead.org>
select() presently has a habit of increasing the value of the user's
`timeout' argument on return.
We were writing back a timeout larger than the original. We _deliberately_
round up, since we know we must wait at _least_ as long as the caller asks
us to.
The patch adds a couple of helper functions for magnitude comparison of
timespecs and of timevals, and uses them to prevent the various poll and
select functions from returning a timeout which is larger than the one which
was passed in.
The patch also fixes a bug in compat_sys_pselect7(): it was adding the new
timeout value to the old one and was returning that. It should just return
the new timeout value.
(We have various handy timespec/timeval-to-from-nsec conversion functions in
time.h. But this code open-codes it all).
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: george anzinger <george@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
[description from AK]
The IBM Summit 3 chipset doesn't implement the HPET timer replacement
option. Since the current Linux code relies on it use a mixed mode with
both PIT for the interrupt and HPET counters for the time keeping. That
was already implemented, but didn't work properly because it was still
using the last interrupt offset in HPET. This resulted in x460 not
booting. Fix this up by using the free running HPET counter.
Shouldn't affect any other machine because they either use full HPET mode
or no HPET at all.
TBD needs a similar 32bit fix.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Pallipadi, Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Bob Picco <bob.picco@hp.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The *at patches introduced fstatat and, due to inusfficient research, I
used the newfstat functions generally as the guideline. The result is that
on 32-bit platforms we don't have all the information needed to implement
fstatat64.
This patch modifies the code to pass up 64-bit information if
__ARCH_WANT_STAT64 is defined. I renamed the syscall entry point to make
this clear. Other archs will continue to use the existing code. On x86-64
the compat code is implemented using a new sys32_ function. this is what
is done for the other stat syscalls as well.
This patch might break some other archs (those which define
__ARCH_WANT_STAT64 and which already wired up the syscall). Yet others
might need changes to accomodate the compatibility mode. I really don't
want to do that work because all this stat handling is a mess (more so in
glibc, but the kernel is also affected). It should be done by the arch
maintainers. I'll provide some stand-alone test shortly. Those who are
eager could compile glibc and run 'make check' (no installation needed).
The patch below has been tested on x86 and x86-64.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
Patch from Ben Dooks
Define the bits for the two board control latches
that control various items on the H1940 iPAQ.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Prevent stalled processing of received data when a driver allocates tty
buffer space but does not immediately follow the allocation with more data
and a call to schedule receive tty processing. (example: hvc_console) This
bug was introduced by the first locking patch for the new tty buffering.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Initialising cpu_possible_map to all-ones with CONFIG_HOTPLUG_CPU means that
a) All for_each_cpu() loops will iterate across all NR_CPUS CPUs, rather
than over possible ones. That can be quite expensive.
b) Soon we'll be allocating per-cpu areas only for possible CPUs. So with
CPU_MASK_ALL, we'll be wasting memory.
I also switched voyager over to not use CPU_MASK_ALL in the non-CPU-hotplug
case. Should be OK..
I note that parisc is also using CPU_MASK_ALL. Suggest that it stop doing
that.
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Paul Jackson <pj@sgi.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Zwane Mwaikambo <zwane@linuxpower.ca>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
It is possible that the reserved crashkernel region can be overlapped with
initrd since the bootloader sets the initrd location. When the initrd
region is freed, the second kernel memory will not be contiguous. The
Kexec_load can cause an oops since there is no contiguous memory to write
the second kernel or this memory could be used in the first kernel itself
and may not be part of the dump. For example, on powerpc, the initrd is
located at 36MB and the crashkernel starts at 32MB. The kexec_load caused
panic since writing into non-allocated memory (after 36MB). We could see
the similar issue even on other archs.
One possibility is to move the initrd outside of crashkernel region. But,
the initrd region will be freed anyway before the system is up. This patch
fixes this issue and frees only regions that are not part of crashkernel
memory in case overlaps.
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Registers system call for the powerpc architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
|
|
This patch set IrDA's addr_len properly, i.e to 4 bytes, the size of the
IrLAP device address.
Signed-off-by: Samuel Ortiz <samuel.ortiz@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlink overrun was broken while improvement of netlink.
Destination socket is used in the place where it was meant to be source socket,
so that now overrun is never sent to user netlink sockets, when it should be,
and it even can be set on kernel socket, which results in complete deadlock
of rtnetlink.
Suggested fix is to restore status quo passing source socket as additional
argument to netlink_attachskb().
A little explanation: overrun is set on a socket, when it failed
to receive some message and sender of this messages does not or even
have no way to handle this error. This happens in two cases:
1. when kernel sends something. Kernel never retransmits and cannot
wait for buffer space.
2. when user sends a broadcast and the message was not delivered
to some recipients.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear unblockable signals beforehand.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
Add unshare syscall for x86-64
ppoll/pselect are not ready yet, but add reservations.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Registers system call for the ia64 architecture.
Reserves space for ppoll and pselect, and adds unshare at system
call number 1296.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
|
|
Manual conflict merge of arch/arm/Kconfig
|
|
Patch from Tony Lindgren
This patch adds the missing cache flushes to common low-level
init that are needed to access the IO region. These flushes
are normally done at the end of devicemaps_init(), but we
need to detect the OMAP core type early.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This patch adds new PCI serial card support.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Patch from Nicolas Pitre
Since:
if (unlikely(__res || __ex_flag))
produces worse code on ARM than:
if (unlikely(__res | __ex_flag))
I therefore made it more explicit:
__res |= __ex_flag;
if (unlikely(__res != 0))
so it is not seen as a typo again.
Also made everything static inline rather than macros for better readability
(both produce the same code after all).
And finally added missing \t from multi-line assembly code.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
|
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
|
It's return value is ignored everywhere.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/bird
|
|
q->ordcolor must only be flipped on initial queueing of a hardbarrier
request.
Constructing ordered sequence and requeueing used to pass through
__elv_add_request() which flips q->ordcolor when it sees a barrier
request.
This patch separates out elv_insert() from __elv_add_request() and uses
elv_insert() when constructing ordered sequence and requeueing.
elv_insert() inserts the given request at the specified position and
does nothing else.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch adds a windfarm module, windfarm_pm112, for the dual core G5s
(both 2 and 4 core models), keeping the machine from getting into
vacuum-cleaner mode ;) For proper credits, the patch was initially
written by Paul Mackerras, and slightly reworked by me to add overtemp
handling among others. The patch also removes the sysfs attributes from
windfarm_pm81 and windfarm_pm91 and instead adds code to the windfarm
core to automagically expose attributes for sensor & controls.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
* compat_alloc_user_space() returns __user pointer
* copying between two userland areas is copy_in_user(), not copy_from_user()
* dereferencing userland pointers is bad
* so's get_user() from local variables
... plus usual __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
A pile of internal functions use only inside mips io.h has names starting
with mem_... and clashing with names in drivers; renamed to __mem_....
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
|
|
|
|
Also, the Solaris syscall table is sized differrently,
and does not go beyond entry 255, so trim off the excess
entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
A bunch of asm/bug.h includes are both not needed (since it will get
pulled anyway) and bogus (since they are done too early). Removed.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
|
|
Need to include the local asm/irq.h to get the NR_IRQS definition.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Registers system call for the i386 architecture.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
If the namespace structure is being shared, allocate a new one and copy
information from the current, shared, structure.
Signed-off-by: Janak Desai <janak@us.ibm.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Compound pages on SMP systems can now often be freed from pagetables via
the release_pages path. This uses put_page_testzero which does not handle
compound pages at all. Releasing constituent pages from process mappings
decrements their count to a large negative number and leaks the reference
at the head page - net result is a memory leak.
The problem was hidden because the debug check in put_page_testzero itself
actually did take compound pages into consideration.
Fix the bug and the debug check.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Fix compilation problem in PM headers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
With the latest 2.6.15 kernel builds for alpha on Debian, we ran into a
problem with undefined references to __cmpxchg_called_with_bad_pointer() in
a couple of kernel modules (xfs.ko and drm.ko; see
http://bugs.debian.org/347556).
It looks like people have been trying to out-clever each other wrt the
definition of "inline" on this architecture :), with the result that
__cmpxchg(), which must be inlined so the compiler can see its argument is
const, is not guaranteed to be inlined. Indeed, it was not being inlined
when building with -Os.
The attached patch fixes the issue by adding an
__attribute__((always_inline)) explicitly to the definition of __cmpxchg()
instead of relying on redefines of "inline" elsewhere to make this happen.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Currently, x86_64 and ia64 arches do not clear the corresponding bits in
the node's cpumask when a cpu goes down or cpu bring up is cancelled. This
is buggy since there are pieces of common code where the cpumask is checked
in the cpu down code path to decide on things (like in the slab down path).
PPC does the right thing, but x86_64 and ia64 don't (This was the reason
Sonny hit upon a slab bug during cpu offline on ppc and could not reproduce
on other arches). This patch fixes it for x86_64. I won't attempt ia64 as
I cannot test it.
Credit for spotting this should go to Alok.
(akpm: this was applied, then reverted. But it's OK now because we now use
for_each_cpu() in the right places).
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
|
|
|
I've noticed that PCI clock was incorrectly reported as 66 MHz while being
mere 33 MHz on RBTX4937 board -- this was due to the different encoding of
the PCI divisor field in CCFG register between TX4927 and TX4937 chips...
Also, RBTX49x7 was printed out as a CPU name (e.g., "CPU is RBTX4937");
and some debug printk() were duplicating each other...
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If mfc0 $12 follows store and the mfc0 is last instruction of a
page and fetching the next instruction causes TLB miss, the result
of the mfc0 might wrongly contain EXL bit.
ERT-TX49H2-027, ERT-TX49H3-012, ERT-TX49HL3-006, ERT-TX49H4-008
Workaround: mask EXL bit of the result or place a nop before mfc0. It
doesn't harm to always clear those bits, so we change the code to do so.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
From Franck Bui-Huu <vagabon.xyz@gmail.com> with modifications by me.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This fixes sparse warnings 'dereference of noderef expression'.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
fls was the only called of flz, so fold flz into fls, same for the
__ilog2 call. Delete the now unused flz function.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
It always left the assembler in reorder mode possibly causing disaster.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Build blast_xxx, blast_xxx_page, blast_xxx_page_indexed from template.
Easier to maintaina and saves 300 lines. Generated code should be
unchanged.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
AMD Au1200 SOC just doesn't have UART3, so KGDB won't even compile for it
as is, here's the fix to make KGDB use UART1.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Fix the #define's for TX4927/37 timer reg's to match the datasheets (those
Signed-off-by: Konstantin Baydarov <kbaidarov@mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
