From: Tobias Klauser The files wanpipe.txt and wan-router.txt in Documentation/networking contain the exact same information (diff between the two shows no document is "Linux WAN Router Utilities Package" and therefor the name wan-router.txt is more appropriate. Signed-off-by: Tobias Klauser Signed-off-by: Domen Puncer Signed-off-by: Andrew Morton --- dev/null | 619 --------------------------------------------------------------- 1 files changed, 619 deletions(-) diff -L Documentation/networking/wanpipe.txt -puN Documentation/networking/wanpipe.txt~remove-duplicate-file-in-documentation-networking /dev/null --- 25/Documentation/networking/wanpipe.txt +++ /dev/null 2003-09-15 06:40:47.000000000 -0700 @@ -1,622 +0,0 @@ ------------------------------------------------------------------------------- -Linux WAN Router Utilities Package ------------------------------------------------------------------------------- -Version 2.2.1 -Mar 28, 2001 -Author: Nenad Corbic -Copyright (c) 1995-2001 Sangoma Technologies Inc. ------------------------------------------------------------------------------- - -INTRODUCTION - -Wide Area Networks (WANs) are used to interconnect Local Area Networks (LANs) -and/or stand-alone hosts over vast distances with data transfer rates -significantly higher than those achievable with commonly used dial-up -connections. - -Usually an external device called `WAN router' sitting on your local network -or connected to your machine's serial port provides physical connection to -WAN. Although router's job may be as simple as taking your local network -traffic, converting it to WAN format and piping it through the WAN link, these -devices are notoriously expensive, with prices as much as 2 - 5 times higher -then the price of a typical PC box. - -Alternatively, considering robustness and multitasking capabilities of Linux, -an internal router can be built (most routers use some sort of stripped down -Unix-like operating system anyway). With a number of relatively inexpensive WAN -interface cards available on the market, a perfectly usable router can be -built for less than half a price of an external router. Yet a Linux box -acting as a router can still be used for other purposes, such as fire-walling, -running FTP, WWW or DNS server, etc. - -This kernel module introduces the notion of a WAN Link Driver (WLD) to Linux -operating system and provides generic hardware-independent services for such -drivers. Why can existing Linux network device interface not be used for -this purpose? Well, it can. However, there are a few key differences between -a typical network interface (e.g. Ethernet) and a WAN link. - -Many WAN protocols, such as X.25 and frame relay, allow for multiple logical -connections (known as `virtual circuits' in X.25 terminology) over a single -physical link. Each such virtual circuit may (and almost always does) lead -to a different geographical location and, therefore, different network. As a -result, it is the virtual circuit, not the physical link, that represents a -route and, therefore, a network interface in Linux terms. - -To further complicate things, virtual circuits are usually volatile in nature -(excluding so called `permanent' virtual circuits or PVCs). With almost no -time required to set up and tear down a virtual circuit, it is highly desirable -to implement on-demand connections in order to minimize network charges. So -unlike a typical network driver, the WAN driver must be able to handle multiple -network interfaces and cope as multiple virtual circuits come into existence -and go away dynamically. - -Last, but not least, WAN configuration is much more complex than that of say -Ethernet and may well amount to several dozens of parameters. Some of them -are "link-wide" while others are virtual circuit-specific. The same holds -true for WAN statistics which is by far more extensive and extremely useful -when troubleshooting WAN connections. Extending the ifconfig utility to suit -these needs may be possible, but does not seem quite reasonable. Therefore, a -WAN configuration utility and corresponding application programmer's interface -is needed for this purpose. - -Most of these problems are taken care of by this module. Its goal is to -provide a user with more-or-less standard look and feel for all WAN devices and -assist a WAN device driver writer by providing common services, such as: - - o User-level interface via /proc file system - o Centralized configuration - o Device management (setup, shutdown, etc.) - o Network interface management (dynamic creation/destruction) - o Protocol encapsulation/decapsulation - -To ba able to use the Linux WAN Router you will also need a WAN Tools package -available from - - ftp.sangoma.com/pub/linux/current_wanpipe/wanpipe-X.Y.Z.tgz - -where vX.Y.Z represent the wanpipe version number. - -For technical questions and/or comments please e-mail to ncorbic@sangoma.com. -For general inquiries please contact Sangoma Technologies Inc. by - - Hotline: 1-800-388-2475 (USA and Canada, toll free) - Phone: (905) 474-1990 ext: 106 - Fax: (905) 474-9223 - E-mail: dm@sangoma.com (David Mandelstam) - WWW: http://www.sangoma.com - - -INSTALLATION - -Please read the WanpipeForLinux.pdf manual on how to -install the WANPIPE tools and drivers properly. - - -After installing wanpipe package: /usr/local/wanrouter/doc. -On the ftp.sangoma.com : /linux/current_wanpipe/doc - - -COPYRIGHT AND LICENSING INFORMATION - -This program is free software; you can redistribute it and/or modify it under -the terms of the GNU General Public License as published by the Free Software -Foundation; either version 2, or (at your option) any later version. - -This program is distributed in the hope that it will be useful, but WITHOUT -ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS -FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - -You should have received a copy of the GNU General Public License along with -this program; if not, write to the Free Software Foundation, Inc., 675 Mass -Ave, Cambridge, MA 02139, USA. - - - -ACKNOWLEDGEMENTS - -This product is based on the WANPIPE(tm) Multiprotocol WAN Router developed -by Sangoma Technologies Inc. for Linux 2.0.x and 2.2.x. Success of the WANPIPE -together with the next major release of Linux kernel in summer 1996 commanded -adequate changes to the WANPIPE code to take full advantage of new Linux -features. - -Instead of continuing developing proprietary interface tied to Sangoma WAN -cards, we decided to separate all hardware-independent code into a separate -module and defined two levels of interfaces - one for user-level applications -and another for kernel-level WAN drivers. WANPIPE is now implemented as a -WAN driver compliant with the WAN Link Driver interface. Also a general -purpose WAN configuration utility and a set of shell scripts was developed to -support WAN router at the user level. - -Many useful ideas concerning hardware-independent interface implementation -were given by Mike McLagan and his implementation -of the Frame Relay router and drivers for Sangoma cards (dlci/sdla). - -With the new implementation of the APIs being incorporated into the WANPIPE, -a special thank goes to Alan Cox in providing insight into BSD sockets. - -Special thanks to all the WANPIPE users who performed field-testing, reported -bugs and made valuable comments and suggestions that help us to improve this -product. - - - -NEW IN THIS RELEASE - - o Updated the WANCFG utility - Calls the pppconfig to configure the PPPD - for async connections. - - o Added the PPPCONFIG utility - Used to configure the PPPD dameon for the - WANPIPE Async PPP and standard serial port. - The wancfg calls the pppconfig to configure - the pppd. - - o Fixed the PCI autodetect feature. - The SLOT 0 was used as an autodetect option - however, some high end PC's slot numbers start - from 0. - - o This release has been tested with the new backupd - daemon release. - - -PRODUCT COMPONENTS AND RELATED FILES - -/etc: (or user defined) - wanpipe1.conf default router configuration file - -/lib/modules/X.Y.Z/misc: - wanrouter.o router kernel loadable module - af_wanpipe.o wanpipe api socket module - -/lib/modules/X.Y.Z/net: - sdladrv.o Sangoma SDLA support module - wanpipe.o Sangoma WANPIPE(tm) driver module - -/proc/net/wanrouter - Config reads current router configuration - Status reads current router status - {name} reads WAN driver statistics - -/usr/sbin: - wanrouter wanrouter start-up script - wanconfig wanrouter configuration utility - sdladump WANPIPE adapter memory dump utility - fpipemon Monitor for Frame Relay - cpipemon Monitor for Cisco HDLC - ppipemon Monitor for PPP - xpipemon Monitor for X25 - wpkbdmon WANPIPE keyboard led monitor/debugger - -/usr/local/wanrouter: - README this file - COPYING GNU General Public License - Setup installation script - Filelist distribution definition file - wanrouter.rc meta-configuration file - (used by the Setup and wanrouter script) - -/usr/local/wanrouter/doc: - wanpipeForLinux.pdf WAN Router User's Manual - -/usr/local/wanrouter/patches: - wanrouter-v2213.gz patch for Linux kernels 2.2.11 up to 2.2.13. - wanrouter-v2214.gz patch for Linux kernel 2.2.14. - wanrouter-v2215.gz patch for Linux kernels 2.2.15 to 2.2.17. - wanrouter-v2218.gz patch for Linux kernels 2.2.18 and up. - wanrouter-v240.gz patch for Linux kernel 2.4.0. - wanrouter-v242.gz patch for Linux kernel 2.4.2 and up. - wanrouter-v2034.gz patch for Linux kernel 2.0.34 - wanrouter-v2036.gz patch for Linux kernel 2.0.36 and up. - -/usr/local/wanrouter/patches/kdrivers: - Sources of the latest WANPIPE device drivers. - These are used to UPGRADE the linux kernel to the newest - version if the kernel source has already been pathced with - WANPIPE drivers. - -/usr/local/wanrouter/samples: - interface sample interface configuration file - wanpipe1.cpri CHDLC primary port - wanpipe2.csec CHDLC secondary port - wanpipe1.fr Frame Relay protocol - wanpipe1.ppp PPP protocol ) - wanpipe1.asy CHDLC ASYNC protocol - wanpipe1.x25 X25 protocol - wanpipe1.stty Sync TTY driver (Used by Kernel PPPD daemon) - wanpipe1.atty Async TTY driver (Used by Kernel PPPD daemon) - wanrouter.rc sample meta-configuration file - -/usr/local/wanrouter/util: - * wan-tools utilities source code - -/usr/local/wanrouter/api/x25: - * x25 api sample programs. -/usr/local/wanrouter/api/chdlc: - * chdlc api sample programs. -/usr/local/wanrouter/api/fr: - * fr api sample programs. -/usr/local/wanrouter/config/wancfg: - wancfg WANPIPE GUI configuration program. - Creates wanpipe#.conf files. -/usr/local/wanrouter/config/cfgft1: - cfgft1 GUI CSU/DSU configuration program. - -/usr/include/linux: - wanrouter.h router API definitions - wanpipe.h WANPIPE API definitions - sdladrv.h SDLA support module API definitions - sdlasfm.h SDLA firmware module definitions - if_wanpipe.h WANPIPE Socket definitions - if_wanpipe_common.h WANPIPE Socket/Driver common definitions. - sdlapci.h WANPIPE PCI definitions - - -/usr/src/linux/net/wanrouter: - * wanrouter source code - -/var/log: - wanrouter wanrouter start-up log (created by the Setup script) - -/var/lock: (or /var/lock/subsys for RedHat) - wanrouter wanrouter lock file (created by the Setup script) - -/usr/local/wanrouter/firmware: - fr514.sfm Frame relay firmware for Sangoma S508/S514 card - cdual514.sfm Dual Port Cisco HDLC firmware for Sangoma S508/S514 card - ppp514.sfm PPP Firmware for Sangoma S508 and S514 cards - x25_508.sfm X25 Firmware for Sangoma S508 card. - - -REVISION HISTORY - -1.0.0 December 31, 1996 Initial version - -1.0.1 January 30, 1997 Status and statistics can be read via /proc - filesystem entries. - -1.0.2 April 30, 1997 Added UDP management via monitors. - -1.0.3 June 3, 1997 UDP management for multiple boards using Frame - Relay and PPP - Enabled continuous transmission of Configure - Request Packet for PPP (for 508 only) - Connection Timeout for PPP changed from 900 to 0 - Flow Control Problem fixed for Frame Relay - -1.0.4 July 10, 1997 S508/FT1 monitoring capability in fpipemon and - ppipemon utilities. - Configurable TTL for UDP packets. - Multicast and Broadcast IP source addresses are - silently discarded. - -1.0.5 July 28, 1997 Configurable T391,T392,N391,N392,N393 for Frame - Relay in router.conf. - Configurable Memory Address through router.conf - for Frame Relay, PPP and X.25. (commenting this - out enables auto-detection). - Fixed freeing up received buffers using kfree() - for Frame Relay and X.25. - Protect sdla_peek() by calling save_flags(), - cli() and restore_flags(). - Changed number of Trace elements from 32 to 20 - Added DLCI specific data monitoring in FPIPEMON. -2.0.0 Nov 07, 1997 Implemented protection of RACE conditions by - critical flags for FRAME RELAY and PPP. - DLCI List interrupt mode implemented. - IPX support in FRAME RELAY and PPP. - IPX Server Support (MARS) - More driver specific stats included in FPIPEMON - and PIPEMON. - -2.0.1 Nov 28, 1997 Bug Fixes for version 2.0.0. - Protection of "enable_irq()" while - "disable_irq()" has been enabled from any other - routine (for Frame Relay, PPP and X25). - Added additional Stats for Fpipemon and Ppipemon - Improved Load Sharing for multiple boards - -2.0.2 Dec 09, 1997 Support for PAP and CHAP for ppp has been - implemented. - -2.0.3 Aug 15, 1998 New release supporting Cisco HDLC, CIR for Frame - relay, Dynamic IP assignment for PPP and Inverse - Arp support for Frame-relay. Man Pages are - included for better support and a new utility - for configuring FT1 cards. - -2.0.4 Dec 09, 1998 Dual Port support for Cisco HDLC. - Support for HDLC (LAPB) API. - Supports BiSync Streaming code for S502E - and S503 cards. - Support for Streaming HDLC API. - Provides a BSD socket interface for - creating applications using BiSync - streaming. - -2.0.5 Aug 04, 1999 CHDLC initializatin bug fix. - PPP interrupt driven driver: - Fix to the PPP line hangup problem. - New PPP firmware - Added comments to the startup SYSTEM ERROR messages - Xpipemon debugging application for the X25 protocol - New USER_MANUAL.txt - Fixed the odd boundary 4byte writes to the board. - BiSync Streaming code has been taken out. - Available as a patch. - Streaming HDLC API has been taken out. - Available as a patch. - -2.0.6 Aug 17, 1999 Increased debugging in statup scripts - Fixed insallation bugs from 2.0.5 - Kernel patch works for both 2.2.10 and 2.2.11 kernels. - There is no functional difference between the two packages - -2.0.7 Aug 26, 1999 o Merged X25API code into WANPIPE. - o Fixed a memeory leak for X25API - o Updated the X25API code for 2.2.X kernels. - o Improved NEM handling. - -2.1.0 Oct 25, 1999 o New code for S514 PCI Card - o New CHDLC and Frame Relay drivers - o PPP and X25 are not supported in this release - -2.1.1 Nov 30, 1999 o PPP support for S514 PCI Cards - -2.1.3 Apr 06, 2000 o Socket based x25api - o Socket based chdlc api - o Socket based fr api - o Dual Port Receive only CHDLC support. - o Asynchronous CHDLC support (Secondary Port) - o cfgft1 GUI csu/dsu configurator - o wancfg GUI configuration file - configurator. - o Architectual directory changes. - -beta-2.1.4 Jul 2000 o Dynamic interface configuration: - Network interfaces reflect the state - of protocol layer. If the protocol becomes - disconnected, driver will bring down - the interface. Once the protocol reconnects - the interface will be brought up. - - Note: This option is turned off by default. - - o Dynamic wanrouter setup using 'wanconfig': - wanconfig utility can be used to - shutdown,restart,start or reconfigure - a virtual circuit dynamically. - - Frame Relay: Each DLCI can be: - created,stopped,restarted and reconfigured - dynamically using wanconfig. - - ex: wanconfig card wanpipe1 dev wp1_fr16 up - - o Wanrouter startup via command line arguments: - wanconfig also supports wanrouter startup via command line - arguments. Thus, there is no need to create a wanpipe#.conf - configuration file. - - o Socket based x25api update/bug fixes. - Added support for LCN numbers greater than 255. - Option to pass up modem messages. - Provided a PCI IRQ check, so a single S514 - card is guaranteed to have a non-sharing interrupt. - - o Fixes to the wancfg utility. - o New FT1 debugging support via *pipemon utilities. - o Frame Relay ARP support Enabled. - -beta3-2.1.4 Jul 2000 o X25 M_BIT Problem fix. - o Added the Multi-Port PPP - Updated utilites for the Multi-Port PPP. - -2.1.4 Aut 2000 - o In X25API: - Maximum packet an application can send - to the driver has been extended to 4096 bytes. - - Fixed the x25 startup bug. Enable - communications only after all interfaces - come up. HIGH SVC/PVC is used to calculate - the number of channels. - Enable protocol only after all interfaces - are enabled. - - o Added an extra state to the FT1 config, kernel module. - o Updated the pipemon debuggers. - - o Blocked the Multi-Port PPP from running on kernels - 2.2.16 or greater, due to syncppp kernel module - change. - -beta1-2.1.5 Nov 15 2000 - o Fixed the MulitPort PPP Support for kernels 2.2.16 and above. - 2.2.X kernels only - - o Secured the driver UDP debugging calls - - All illegal netowrk debugging calls are reported to - the log. - - Defined a set of allowed commands, all other denied. - - o Cpipemon - - Added set FT1 commands to the cpipemon. Thus CSU/DSU - configuraiton can be performed using cpipemon. - All systems that cannot run cfgft1 GUI utility should - use cpipemon to configure the on board CSU/DSU. - - - o Keyboard Led Monitor/Debugger - - A new utilty /usr/sbin/wpkbdmon uses keyboard leds - to convey operatinal statistic information of the - Sangoma WANPIPE cards. - NUM_LOCK = Line State (On=connected, Off=disconnected) - CAPS_LOCK = Tx data (On=transmitting, Off=no tx data) - SCROLL_LOCK = Rx data (On=receiving, Off=no rx data - - o Hardware probe on module load and dynamic device allocation - - During WANPIPE module load, all Sangoma cards are probed - and found information is printed in the /var/log/messages. - - If no cards are found, the module load fails. - - Appropriate number of devices are dynamically loaded - based on the number of Sangoma cards found. - - Note: The kernel configuraiton option - CONFIG_WANPIPE_CARDS has been taken out. - - o Fixed the Frame Relay and Chdlc network interfaces so they are - compatible with libpcap libraries. Meaning, tcpdump, snort, - ethereal, and all other packet sniffers and debuggers work on - all WANPIPE netowrk interfaces. - - Set the network interface encoding type to ARPHRD_PPP. - This tell the sniffers that data obtained from the - network interface is in pure IP format. - Fix for 2.2.X kernels only. - - o True interface encoding option for Frame Relay and CHDLC - - The above fix sets the network interface encoding - type to ARPHRD_PPP, however some customers use - the encoding interface type to determine the - protocol running. Therefore, the TURE ENCODING - option will set the interface type back to the - original value. - - NOTE: If this option is used with Frame Relay and CHDLC - libpcap library support will be broken. - i.e. tcpdump will not work. - Fix for 2.2.x Kernels only. - - o Ethernet Bridgind over Frame Relay - - The Frame Relay bridging has been developed by - Kristian Hoffmann and Mark Wells. - - The Linux kernel bridge is used to send ethernet - data over the frame relay links. - For 2.2.X Kernels only. - - o Added extensive 2.0.X support. Most new features of - 2.1.5 for protocols Frame Relay, PPP and CHDLC are - supported under 2.0.X kernels. - -beta1-2.2.0 Dec 30 2000 - o Updated drivers for 2.4.X kernels. - o Updated drivers for SMP support. - o X25API is now able to share PCI interrupts. - o Took out a general polling routine that was used - only by X25API. - o Added appropriate locks to the dynamic reconfiguration - code. - o Fixed a bug in the keyboard debug monitor. - -beta2-2.2.0 Jan 8 2001 - o Patches for 2.4.0 kernel - o Patches for 2.2.18 kernel - o Minor updates to PPP and CHLDC drivers. - Note: No functinal difference. - -beta3-2.2.9 Jan 10 2001 - o I missed the 2.2.18 kernel patches in beta2-2.2.0 - release. They are included in this release. - -Stable Release -2.2.0 Feb 01 2001 - o Bug fix in wancfg GUI configurator. - The edit function didn't work properly. - - -bata1-2.2.1 Feb 09 2001 - o WANPIPE TTY Driver emulation. - Two modes of operation Sync and Async. - Sync: Using the PPPD daemon, kernel SyncPPP layer - and the Wanpipe sync TTY driver: a PPP protocol - connection can be established via Sangoma adapter, over - a T1 leased line. - - The 2.4.0 kernel PPP layer supports MULTILINK - protocol, that can be used to bundle any number of Sangoma - adapters (T1 lines) into one, under a single IP address. - Thus, efficiently obtaining multiple T1 throughput. - - NOTE: The remote side must also implement MULTILINK PPP - protocol. - - Async:Using the PPPD daemon, kernel AsyncPPP layer - and the WANPIPE async TTY driver: a PPP protocol - connection can be established via Sangoma adapter and - a modem, over a telephone line. - - Thus, the WANPIPE async TTY driver simulates a serial - TTY driver that would normally be used to interface the - MODEM to the linux kernel. - - o WANPIPE PPP Backup Utility - This utility will monitor the state of the PPP T1 line. - In case of failure, a dial up connection will be established - via pppd daemon, ether via a serial tty driver (serial port), - or a WANPIPE async TTY driver (in case serial port is unavailable). - - Furthermore, while in dial up mode, the primary PPP T1 link - will be monitored for signs of life. - - If the PPP T1 link comes back to life, the dial up connection - will be shutdown and T1 line re-established. - - - o New Setup installation script. - Option to UPGRADE device drivers if the kernel source has - already been patched with WANPIPE. - - Option to COMPILE WANPIPE modules against the currently - running kernel, thus no need for manual kernel and module - re-compilatin. - - o Updates and Bug Fixes to wancfg utility. - -bata2-2.2.1 Feb 20 2001 - - o Bug fixes to the CHDLC device drivers. - The driver had compilation problems under kernels - 2.2.14 or lower. - - o Bug fixes to the Setup installation script. - The device drivers compilation options didn't work - properly. - - o Update to the wpbackupd daemon. - Optimized the cross-over times, between the primary - link and the backup dialup. - -beta3-2.2.1 Mar 02 2001 - o Patches for 2.4.2 kernel. - - o Bug fixes to util/ make files. - o Bug fixes to the Setup installation script. - - o Took out the backupd support and made it into - as separate package. - -beta4-2.2.1 Mar 12 2001 - - o Fix to the Frame Relay Device driver. - IPSAC sends a packet of zero length - header to the frame relay driver. The - driver tries to push its own 2 byte header - into the packet, which causes the driver to - crash. - - o Fix the WANPIPE re-configuration code. - Bug was found by trying to run the cfgft1 while the - interface was already running. - - o Updates to cfgft1. - Writes a wanpipe#.cfgft1 configuration file - once the CSU/DSU is configured. This file can - holds the current CSU/DSU configuration. - - - ->>>>>> END OF README <<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<<< - - _