From: Bjorn Helgaas At least some VIA chipsets require the fixup even in IO-APIC mode. This was found and debugged with the patient assistance of Stian Jordet on an Asus CUV266-DLS motherboard. Signed-off-by: Bjorn Helgaas Signed-off-by: Andrew Morton --- drivers/pci/quirks.c | 35 +++++++++++++---------------------- 1 files changed, 13 insertions(+), 22 deletions(-) diff -puN drivers/pci/quirks.c~pci-do-via-irq-fixup-always-not-just-in-pic-mode drivers/pci/quirks.c --- 25/drivers/pci/quirks.c~pci-do-via-irq-fixup-always-not-just-in-pic-mode 2005-06-06 00:13:38.000000000 -0700 +++ 25-akpm/drivers/pci/quirks.c 2005-06-06 00:13:38.000000000 -0700 @@ -466,17 +466,6 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_SE /* - * Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip - * devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature: - * when written, it makes an internal connection to the PIC. - * For these devices, this register is defined to be 4 bits wide. - * Normally this is fine. However for IO-APIC motherboards, or - * non-x86 architectures (yes Via exists on PPC among other places), - * we must mask the PCI_INTERRUPT_LINE value versus 0xf to get - * interrupts delivered properly. - */ - -/* * FIXME: it is questionable that quirk_via_acpi * is needed. It shows up as an ISA bridge, and does not * support the PCI_INTERRUPT_LINE register at all. Therefore @@ -498,28 +487,30 @@ static void __devinit quirk_via_acpi(str DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C586_3, quirk_via_acpi ); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_82C686_4, quirk_via_acpi ); -static void quirk_via_irqpic(struct pci_dev *dev) +/* + * Via 686A/B: The PCI_INTERRUPT_LINE register for the on-chip + * devices, USB0/1, AC97, MC97, and ACPI, has an unusual feature: + * when written, it makes an internal connection to the PIC. + * For these devices, this register is defined to be 4 bits wide. + * Normally this is fine. However for IO-APIC motherboards, or + * non-x86 architectures (yes Via exists on PPC among other places), + * we must mask the PCI_INTERRUPT_LINE value versus 0xf to get + * interrupts delivered properly. + */ +static void quirk_via_irq(struct pci_dev *dev) { u8 irq, new_irq; -#ifdef CONFIG_X86_IO_APIC - if (nr_ioapics && !skip_ioapic_setup) - return; -#endif -#ifdef CONFIG_ACPI - if (acpi_irq_model != ACPI_IRQ_MODEL_PIC) - return; -#endif new_irq = dev->irq & 0xf; pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &irq); if (new_irq != irq) { - printk(KERN_INFO "PCI: Via PIC IRQ fixup for %s, from %d to %d\n", + printk(KERN_INFO "PCI: Via IRQ fixup for %s, from %d to %d\n", pci_name(dev), irq, new_irq); udelay(15); /* unknown if delay really needed */ pci_write_config_byte(dev, PCI_INTERRUPT_LINE, new_irq); } } -DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irqpic); +DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_VIA, PCI_ANY_ID, quirk_via_irq); /* * PIIX3 USB: We have to disable USB interrupts that are _